/**
* e1000e_check_options - Range Checking for Command Line Parameters
* @adapter: board private structure
*
* This routine checks all command line parameters for valid user
* input. If an invalid value is given, or if no user specified
* value exists, a default value is used. The final value is stored
* in a variable in the adapter structure.
**/
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
dev_notice(&adapter->pdev->dev,
"Warning: no configuration for board #%i\n", bd);
dev_notice(&adapter->pdev->dev,
"Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY } }
};
if (num_TxIntDelay > bd) {
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt,
adapter);
} else {
adapter->tx_int_delay = opt.def;
}
}
{ /* Transmit Absolute Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY } }
};
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
}
{ /* Receive Interrupt Delay */
static struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY } }
};
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
adapter);
} else {
adapter->rx_int_delay = opt.def;
}
}
{ /* Receive Absolute Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY } }
};
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
}
{ /* Interrupt Throttling Rate */
static const struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of "
__MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR } }
};
if (num_InterruptThrottleRate > bd) {
adapter->itr = InterruptThrottleRate[bd];
/*
* Make sure a message is printed for non-special
* values. And in case of an invalid option, display
* warning, use default and go through itr/itr_setting
* adjustment logic below
*/
if ((adapter->itr > 4) &&
e1000_validate_option(&adapter->itr, &opt, adapter))
adapter->itr = opt.def;
} else {
/*
* If no option specified, use default value and go
* through the logic below to adjust itr/itr_setting
*/
adapter->itr = opt.def;
/*
* Make sure a message is printed for non-special
* default values
*/
if (adapter->itr > 4)
dev_info(&adapter->pdev->dev,
"%s set to default %d\n", opt.name,
adapter->itr);
}
adapter->itr_setting = adapter->itr;
switch (adapter->itr) {
case 0:
dev_info(&adapter->pdev->dev, "%s turned off\n",
opt.name);
break;
case 1:
dev_info(&adapter->pdev->dev,
"%s set to dynamic mode\n", opt.name);
adapter->itr = 20000;
break;
case 3:
dev_info(&adapter->pdev->dev,
"%s set to dynamic conservative mode\n",
opt.name);
adapter->itr = 20000;
break;
case 4:
dev_info(&adapter->pdev->dev,
"%s set to simplified (2000-8000 ints) mode\n",
opt.name);
break;
default:
/*
* Save the setting, because the dynamic bits
* change itr.
*
* Clear the lower two bits because
* they are used as control.
*/
adapter->itr_setting &= ~3;
break;
}
}
{ /* Interrupt Mode */
static struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Mode",
#ifndef CONFIG_PCI_MSI
.err = "defaulting to 0 (legacy)",
.def = E1000E_INT_MODE_LEGACY,
.arg = { .r = { .min = 0,
.max = 0 } }
#endif
};
#ifdef CONFIG_PCI_MSI
if (adapter->flags & FLAG_HAS_MSIX) {
opt.err = kstrdup("defaulting to 2 (MSI-X)",
GFP_KERNEL);
opt.def = E1000E_INT_MODE_MSIX;
opt.arg.r.max = E1000E_INT_MODE_MSIX;
} else {
opt.err = kstrdup("defaulting to 1 (MSI)", GFP_KERNEL);
opt.def = E1000E_INT_MODE_MSI;
opt.arg.r.max = E1000E_INT_MODE_MSI;
}
if (!opt.err) {
dev_err(&adapter->pdev->dev,
"Failed to allocate memory\n");
return;
}
#endif
if (num_IntMode > bd) {
unsigned int int_mode = IntMode[bd];
e1000_validate_option(&int_mode, &opt, adapter);
adapter->int_mode = int_mode;
} else {
adapter->int_mode = opt.def;
}
#ifdef CONFIG_PCI_MSI
kfree(opt.err);
#endif
}
{ /* Smart Power Down */
static const struct e1000_option opt = {
.type = enable_option,
.name = "PHY Smart Power Down",
.err = "defaulting to Disabled",
.def = OPTION_DISABLED
};
if (num_SmartPowerDownEnable > bd) {
unsigned int spd = SmartPowerDownEnable[bd];
e1000_validate_option(&spd, &opt, adapter);
if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
&& spd)
adapter->flags |= FLAG_SMART_POWER_DOWN;
}
}
{ /* CRC Stripping */
static const struct e1000_option opt = {
.type = enable_option,
.name = "CRC Stripping",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_CrcStripping > bd) {
unsigned int crc_stripping = CrcStripping[bd];
e1000_validate_option(&crc_stripping, &opt, adapter);
if (crc_stripping == OPTION_ENABLED)
adapter->flags2 |= FLAG2_CRC_STRIPPING;
} else {
adapter->flags2 |= FLAG2_CRC_STRIPPING;
}
}
{ /* Kumeran Lock Loss Workaround */
static const struct e1000_option opt = {
.type = enable_option,
.name = "Kumeran Lock Loss Workaround",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_KumeranLockLoss > bd) {
unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
kmrn_lock_loss);
} else {
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
opt.def);
}
}
{ /* Write-protect NVM */
static const struct e1000_option opt = {
.type = enable_option,
.name = "Write-protect NVM",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (adapter->flags & FLAG_IS_ICH) {
if (num_WriteProtectNVM > bd) {
unsigned int write_protect_nvm = WriteProtectNVM[bd];
e1000_validate_option(&write_protect_nvm, &opt,
adapter);
if (write_protect_nvm)
adapter->flags |= FLAG_READ_ONLY_NVM;
} else {
if (opt.def)
adapter->flags |= FLAG_READ_ONLY_NVM;
}
}
}
{ /* EEE for parts supporting the feature */
static const struct e1000_option opt = {
.type = enable_option,
.name = "EEE Support",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (adapter->flags2 & FLAG2_HAS_EEE) {
/* Currently only supported on 82579 */
if (num_EEE > bd) {
unsigned int eee = EEE[bd];
e1000_validate_option(&eee, &opt, adapter);
hw->dev_spec.ich8lan.eee_disable = !eee;
} else {
hw->dev_spec.ich8lan.eee_disable = !opt.def;
}
}
}
}
/**
* e1000e_check_options - Range Checking for Command Line Parameters
* @adapter: board private structure
*
* This routine checks all command line parameters for valid user
* input. If an invalid value is given, or if no user specified
* value exists, a default value is used. The final value is stored
* in a variable in the adapter structure.
**/
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
e_notice("Warning: no configuration for board #%i\n", bd);
e_notice("Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY } }
};
if (num_TxIntDelay > bd) {
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt,
adapter);
} else {
adapter->tx_int_delay = opt.def;
}
}
{ /* Transmit Absolute Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY } }
};
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
}
{ /* Receive Interrupt Delay */
struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY } }
};
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
adapter);
} else {
adapter->rx_int_delay = opt.def;
}
}
{ /* Receive Absolute Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY } }
};
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
}
{ /* Interrupt Throttling Rate */
const struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of "
__MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR } }
};
if (num_InterruptThrottleRate > bd) {
adapter->itr = InterruptThrottleRate[bd];
switch (adapter->itr) {
case 0:
e_info("%s turned off\n", opt.name);
break;
case 1:
e_info("%s set to dynamic mode\n", opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
case 3:
e_info("%s set to dynamic conservative mode\n",
opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
default:
/*
* Save the setting, because the dynamic bits
* change itr.
*/
if (e1000_validate_option(&adapter->itr, &opt,
adapter) &&
(adapter->itr == 3)) {
/*
* In case of invalid user value,
* default to conservative mode.
*/
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
} else {
/*
* Clear the lower two bits because
* they are used as control.
*/
adapter->itr_setting =
adapter->itr & ~3;
}
break;
}
} else {
adapter->itr_setting = opt.def;
adapter->itr = 20000;
}
}
{ /* Interrupt Mode */
struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Mode",
.err = "defaulting to 2 (MSI-X)",
.def = E1000E_INT_MODE_MSIX,
.arg = { .r = { .min = MIN_INTMODE,
.max = MAX_INTMODE } }
};
if (num_IntMode > bd) {
unsigned int int_mode = IntMode[bd];
e1000_validate_option(&int_mode, &opt, adapter);
adapter->int_mode = int_mode;
} else {
adapter->int_mode = opt.def;
}
}
{ /* Smart Power Down */
const struct e1000_option opt = {
.type = enable_option,
.name = "PHY Smart Power Down",
.err = "defaulting to Disabled",
.def = OPTION_DISABLED
};
if (num_SmartPowerDownEnable > bd) {
unsigned int spd = SmartPowerDownEnable[bd];
e1000_validate_option(&spd, &opt, adapter);
if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
&& spd)
adapter->flags |= FLAG_SMART_POWER_DOWN;
}
}
{ /* CRC Stripping */
const struct e1000_option opt = {
.type = enable_option,
.name = "CRC Stripping",
.err = "defaulting to enabled",
.def = OPTION_ENABLED
};
if (num_CrcStripping > bd) {
unsigned int crc_stripping = CrcStripping[bd];
e1000_validate_option(&crc_stripping, &opt, adapter);
if (crc_stripping == OPTION_ENABLED)
adapter->flags2 |= FLAG2_CRC_STRIPPING;
}
}
{ /* Kumeran Lock Loss Workaround */
const struct e1000_option opt = {
.type = enable_option,
.name = "Kumeran Lock Loss Workaround",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_KumeranLockLoss > bd) {
unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
kmrn_lock_loss);
} else {
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
opt.def);
}
}
{ /* Write-protect NVM */
const struct e1000_option opt = {
.type = enable_option,
.name = "Write-protect NVM",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (adapter->flags & FLAG_IS_ICH) {
if (num_WriteProtectNVM > bd) {
unsigned int write_protect_nvm = WriteProtectNVM[bd];
e1000_validate_option(&write_protect_nvm, &opt,
adapter);
if (write_protect_nvm)
adapter->flags |= FLAG_READ_ONLY_NVM;
} else {
if (opt.def)
adapter->flags |= FLAG_READ_ONLY_NVM;
}
}
}
}
/**
* e1000e_check_options - Range Checking for Command Line Parameters
* @adapter: board private structure
*
* This routine checks all command line parameters for valid user
* input. If an invalid value is given, or if no user specified
* value exists, a default value is used. The final value is stored
* in a variable in the adapter structure.
**/
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
e_notice("Warning: no configuration for board #%i\n", bd);
e_notice("Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY } }
};
if (num_TxIntDelay > bd) {
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt,
adapter);
} else {
adapter->tx_int_delay = opt.def;
}
}
{ /* Transmit Absolute Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY } }
};
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
}
{ /* Receive Interrupt Delay */
static struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY } }
};
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
adapter);
} else {
adapter->rx_int_delay = opt.def;
}
}
{ /* Receive Absolute Interrupt Delay */
static const struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY } }
};
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
}
{ /* Interrupt Throttling Rate */
static const struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of "
__MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR } }
};
if (num_InterruptThrottleRate > bd) {
adapter->itr = InterruptThrottleRate[bd];
switch (adapter->itr) {
case 0:
e_info("%s turned off\n", opt.name);
break;
case 1:
e_info("%s set to dynamic mode\n", opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
case 3:
e_info("%s set to dynamic conservative mode\n",
opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
case 4:
e_info("%s set to simplified (2000-8000 ints) "
"mode\n", opt.name);
adapter->itr_setting = 4;
break;
default:
/*
* Save the setting, because the dynamic bits
* change itr.
*/
if (e1000_validate_option(&adapter->itr, &opt,
adapter) &&
(adapter->itr == 3)) {
/*
* In case of invalid user value,
* default to conservative mode.
*/
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
} else {
/*
* Clear the lower two bits because
* they are used as control.
*/
adapter->itr_setting =
adapter->itr & ~3;
}
break;
}
} else {
adapter->itr_setting = opt.def;
adapter->itr = 20000;
}
}
#ifdef CONFIG_E1000E_MSIX
{ /* Interrupt Mode */
static struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Mode",
.err = "defaulting to 2 (MSI-X)",
.def = E1000E_INT_MODE_MSIX,
.arg = { .r = { .min = MIN_INTMODE,
.max = MAX_INTMODE } }
};
if (num_IntMode > bd) {
unsigned int int_mode = IntMode[bd];
e1000_validate_option(&int_mode, &opt, adapter);
adapter->int_mode = int_mode;
} else {
adapter->int_mode = opt.def;
}
}
#endif /* CONFIG_E1000E_MSIX */
{ /* Smart Power Down */
static const struct e1000_option opt = {
.type = enable_option,
.name = "PHY Smart Power Down",
.err = "defaulting to Disabled",
.def = OPTION_DISABLED
};
if (num_SmartPowerDownEnable > bd) {
unsigned int spd = SmartPowerDownEnable[bd];
e1000_validate_option(&spd, &opt, adapter);
if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
&& spd)
adapter->flags |= FLAG_SMART_POWER_DOWN;
}
}
{ /* CRC Stripping */
static const struct e1000_option opt = {
.type = enable_option,
.name = "CRC Stripping",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_CrcStripping > bd) {
unsigned int crc_stripping = CrcStripping[bd];
e1000_validate_option(&crc_stripping, &opt, adapter);
if (crc_stripping == OPTION_ENABLED)
adapter->flags2 |= FLAG2_CRC_STRIPPING;
} else {
adapter->flags2 |= FLAG2_CRC_STRIPPING;
}
}
{ /* Kumeran Lock Loss Workaround */
static const struct e1000_option opt = {
.type = enable_option,
.name = "Kumeran Lock Loss Workaround",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_KumeranLockLoss > bd) {
unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
kmrn_lock_loss);
} else {
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
opt.def);
}
}
{ /* EEE for parts supporting the feature */
static const struct e1000_option opt = {
.type = enable_option,
.name = "EEE Support",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (adapter->flags2 & FLAG2_HAS_EEE) {
/* Currently only supported on 82579 */
if (num_EEE > bd) {
unsigned int eee = EEE[bd];
e1000_validate_option(&eee, &opt, adapter);
hw->dev_spec.ich8lan.eee_disable = !eee;
} else {
hw->dev_spec.ich8lan.eee_disable = !opt.def;
}
}
}
{ /* configure node specific allocation */
static struct e1000_option opt = {
.type = range_option,
.name = "Node used to allocate memory",
.err = "defaulting to -1 (disabled)",
#ifdef HAVE_EARLY_VMALLOC_NODE
.def = 0,
#else
.def = -1,
#endif
.arg = { .r = { .min = 0,
.max = MAX_NUMNODES - 1 } }
};
int node = opt.def;
/* if the default was zero then we need to set the
* default value to an online node, which is not
* necessarily zero, and the constant initializer
* above can't take first_online_node */
if (node == 0)
/* must set opt.def for validate */
opt.def = node = first_online_node;
if (num_Node > bd) {
node = Node[bd];
e1000_validate_option((uint *)&node, &opt, adapter);
if (node != OPTION_UNSET)
e_info("node used for allocation: %d\n", node);
}
/* check sanity of the value */
if ((node != -1) && !node_online(node)) {
e_info("ignoring node set to invalid value %d\n", node);
node = opt.def;
}
adapter->node = node;
}
}
/**
* e1000e_check_options - Range Checking for Command Line Parameters
* @adapter: board private structure
*
* This routine checks all command line parameters for valid user
* input. If an invalid value is given, or if no user specified
* value exists, a default value is used. The final value is stored
* in a variable in the adapter structure.
**/
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
struct net_device *netdev = adapter->netdev;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
ndev_notice(netdev,
"Warning: no configuration for board #%i\n", bd);
ndev_notice(netdev, "Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY } }
};
if (num_TxIntDelay > bd) {
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt,
adapter);
} else {
adapter->tx_int_delay = opt.def;
}
}
{ /* Transmit Absolute Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY } }
};
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
}
{ /* Receive Interrupt Delay */
struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY } }
};
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
adapter);
} else {
adapter->rx_int_delay = opt.def;
}
}
{ /* Receive Absolute Interrupt Delay */
const struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY } }
};
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
}
{ /* Interrupt Throttling Rate */
const struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of "
__MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR } }
};
if (num_InterruptThrottleRate > bd) {
adapter->itr = InterruptThrottleRate[bd];
switch (adapter->itr) {
case 0:
ndev_info(netdev, "%s turned off\n",
opt.name);
break;
case 1:
ndev_info(netdev,
"%s set to dynamic mode\n",
opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
case 3:
ndev_info(netdev,
"%s set to dynamic conservative mode\n",
opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
default:
e1000_validate_option(&adapter->itr, &opt,
adapter);
/*
* save the setting, because the dynamic bits
* change itr. clear the lower two bits
* because they are used as control
*/
adapter->itr_setting = adapter->itr & ~3;
break;
}
} else {
adapter->itr_setting = opt.def;
adapter->itr = 20000;
}
}
{ /* Smart Power Down */
const struct e1000_option opt = {
.type = enable_option,
.name = "PHY Smart Power Down",
.err = "defaulting to Disabled",
.def = OPTION_DISABLED
};
if (num_SmartPowerDownEnable > bd) {
unsigned int spd = SmartPowerDownEnable[bd];
e1000_validate_option(&spd, &opt, adapter);
if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
&& spd)
adapter->flags |= FLAG_SMART_POWER_DOWN;
}
}
{ /* Kumeran Lock Loss Workaround */
const struct e1000_option opt = {
.type = enable_option,
.name = "Kumeran Lock Loss Workaround",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_KumeranLockLoss > bd) {
unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
kmrn_lock_loss);
} else {
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
opt.def);
}
}
}
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
e_notice("Warning: no configuration for board #%i\n", bd);
e_notice("Using defaults for all values\n");
}
{
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TIDV),
.def = DEFAULT_TIDV,
.arg = { .r = { .min = MIN_TXDELAY,
.max = MAX_TXDELAY } }
};
if (num_TxIntDelay > bd) {
adapter->tx_int_delay = TxIntDelay[bd];
e1000_validate_option(&adapter->tx_int_delay, &opt,
adapter);
} else {
adapter->tx_int_delay = opt.def;
}
}
{
static const struct e1000_option opt = {
.type = range_option,
.name = "Transmit Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_TADV),
.def = DEFAULT_TADV,
.arg = { .r = { .min = MIN_TXABSDELAY,
.max = MAX_TXABSDELAY } }
};
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
}
{
static struct e1000_option opt = {
.type = range_option,
.name = "Receive Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RDTR),
.def = DEFAULT_RDTR,
.arg = { .r = { .min = MIN_RXDELAY,
.max = MAX_RXDELAY } }
};
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
adapter);
} else {
adapter->rx_int_delay = opt.def;
}
}
{
static const struct e1000_option opt = {
.type = range_option,
.name = "Receive Absolute Interrupt Delay",
.err = "using default of "
__MODULE_STRING(DEFAULT_RADV),
.def = DEFAULT_RADV,
.arg = { .r = { .min = MIN_RXABSDELAY,
.max = MAX_RXABSDELAY } }
};
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
}
{
static const struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Throttling Rate (ints/sec)",
.err = "using default of "
__MODULE_STRING(DEFAULT_ITR),
.def = DEFAULT_ITR,
.arg = { .r = { .min = MIN_ITR,
.max = MAX_ITR } }
};
if (num_InterruptThrottleRate > bd) {
adapter->itr = InterruptThrottleRate[bd];
if ((adapter->itr > 4) &&
e1000_validate_option(&adapter->itr, &opt, adapter))
adapter->itr = opt.def;
} else {
adapter->itr = opt.def;
if (adapter->itr > 40)
e_info("%s set to default %d\n", opt.name,
adapter->itr);
}
adapter->itr_setting = adapter->itr;
switch (adapter->itr) {
case 0:
e_info("%s turned off\n", opt.name);
break;
case 1:
e_info("%s set to dynamic mode\n", opt.name);
adapter->itr = 20000;
break;
case 3:
e_info("%s set to dynamic conservative mode\n",
opt.name);
adapter->itr = 20000;
break;
case 4:
e_info("%s set to simplified (2000-8000 ints) mode\n",
opt.name);
break;
default:
adapter->itr_setting &= ~3;
break;
}
}
{
static struct e1000_option opt = {
.type = range_option,
.name = "Interrupt Mode",
#ifndef CONFIG_PCI_MSI
.err = "defaulting to 0 (legacy)",
.def = E1000E_INT_MODE_LEGACY,
.arg = { .r = { .min = 0,
.max = 0 } }
#endif
};
#ifdef CONFIG_PCI_MSI
if (adapter->flags & FLAG_HAS_MSIX) {
opt.err = kstrdup("defaulting to 2 (MSI-X)",
GFP_KERNEL);
opt.def = E1000E_INT_MODE_MSIX;
opt.arg.r.max = E1000E_INT_MODE_MSIX;
} else {
opt.err = kstrdup("defaulting to 1 (MSI)", GFP_KERNEL);
opt.def = E1000E_INT_MODE_MSI;
opt.arg.r.max = E1000E_INT_MODE_MSI;
}
if (!opt.err) {
dev_err(&adapter->pdev->dev,
"Failed to allocate memory\n");
return;
}
#endif
if (num_IntMode > bd) {
unsigned int int_mode = IntMode[bd];
e1000_validate_option(&int_mode, &opt, adapter);
adapter->int_mode = int_mode;
} else {
adapter->int_mode = opt.def;
}
#ifdef CONFIG_PCI_MSI
kfree(opt.err);
#endif
}
{
static const struct e1000_option opt = {
.type = enable_option,
.name = "PHY Smart Power Down",
.err = "defaulting to Disabled",
.def = OPTION_DISABLED
};
if (num_SmartPowerDownEnable > bd) {
unsigned int spd = SmartPowerDownEnable[bd];
e1000_validate_option(&spd, &opt, adapter);
if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
&& spd)
adapter->flags |= FLAG_SMART_POWER_DOWN;
}
}
{
static const struct e1000_option opt = {
.type = enable_option,
.name = "CRC Stripping",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_CrcStripping > bd) {
unsigned int crc_stripping = CrcStripping[bd];
e1000_validate_option(&crc_stripping, &opt, adapter);
if (crc_stripping == OPTION_ENABLED) {
adapter->flags2 |= FLAG2_CRC_STRIPPING;
adapter->flags2 |= FLAG2_DFLT_CRC_STRIPPING;
}
} else {
adapter->flags2 |= FLAG2_CRC_STRIPPING;
adapter->flags2 |= FLAG2_DFLT_CRC_STRIPPING;
}
}
{
static const struct e1000_option opt = {
.type = enable_option,
.name = "Kumeran Lock Loss Workaround",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (num_KumeranLockLoss > bd) {
unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
kmrn_lock_loss);
} else {
if (hw->mac.type == e1000_ich8lan)
e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
opt.def);
}
}
{
static const struct e1000_option opt = {
.type = enable_option,
.name = "Write-protect NVM",
.err = "defaulting to Enabled",
.def = OPTION_ENABLED
};
if (adapter->flags & FLAG_IS_ICH) {
if (num_WriteProtectNVM > bd) {
unsigned int write_protect_nvm = WriteProtectNVM[bd];
e1000_validate_option(&write_protect_nvm, &opt,
adapter);
if (write_protect_nvm)
adapter->flags |= FLAG_READ_ONLY_NVM;
} else {
if (opt.def)
adapter->flags |= FLAG_READ_ONLY_NVM;
}
}
}
}
