static int load_cpu_fw_direct(const char *fn, u8 __iomem *mem, struct cx18 *cx)
{
	const struct firmware *fw = NULL;
	int i, j;
	unsigned size;
	u32 __iomem *dst = (u32 __iomem *)mem;
	const u32 *src;

	if (request_firmware(&fw, fn, &cx->pci_dev->dev)) {
		CX18_ERR("Unable to open firmware %s\n", fn);
		CX18_ERR("Did you put the firmware in the hotplug firmware directory?\n");
		return -ENOMEM;
	}

	src = (const u32 *)fw->data;

	for (i = 0; i < fw->size; i += 4096) {
		cx18_setup_page(cx, i);
		for (j = i; j < fw->size && j < i + 4096; j += 4) {
			/* no need for endianness conversion on the ppc */
			cx18_raw_writel(cx, *src, dst);
			if (cx18_raw_readl(cx, dst) != *src) {
				CX18_ERR("Mismatch at offset %x\n", i);
				release_firmware(fw);
				cx18_setup_page(cx, 0);
				return -EIO;
			}
			dst++;
			src++;
		}
	}
	if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
		CX18_INFO("loaded %s firmware (%zd bytes)\n", fn, fw->size);
	size = fw->size;
	release_firmware(fw);
	cx18_setup_page(cx, SCB_OFFSET);
	return size;
}
Ejemplo n.º 2
0
void cx18_unmute(struct cx18 *cx)
{
    u32 h;
    if (atomic_read(&cx->ana_capturing)) {
        h = cx18_find_handle(cx);
        if (h != CX18_INVALID_TASK_HANDLE) {
            cx18_msleep_timeout(100, 0);
            cx18_vapi(cx, CX18_CPU_SET_MISC_PARAMETERS, 2, h, 12);
            cx18_vapi(cx, CX18_CPU_SET_AUDIO_MUTE, 2, h, 0);
        } else
            CX18_ERR("Can't find valid task handle for unmute\n");
    }
    CX18_DEBUG_INFO("Unmute\n");
}
Ejemplo n.º 3
0
/* Calls i2c device based on CX18_HW_ flag. If hw == 0, then do nothing.
   If hw == CX18_HW_GPIO then call the gpio handler. */
int cx18_i2c_hw(struct cx18 *cx, u32 hw, unsigned int cmd, void *arg)
{
	int addr;

	if (hw == CX18_HW_GPIO || hw == 0)
		return 0;
	if (hw == CX18_HW_CX23418)
		return cx18_av_cmd(cx, cmd, arg);

	addr = cx18_i2c_hw_addr(cx, hw);
	if (addr < 0) {
		CX18_ERR("i2c hardware 0x%08x (%s) not found for cmd 0x%x!\n",
			       hw, cx18_i2c_hw_name(hw), cmd);
		return addr;
	}
	return cx18_call_i2c_client(cx, addr, cmd, arg);
}
Ejemplo n.º 4
0
int cx18_v4l2_open(struct file *filp)
{
	int res;
	struct video_device *video_dev = video_devdata(filp);
	struct cx18_stream *s = video_get_drvdata(video_dev);
	struct cx18 *cx = s->cx;

	mutex_lock(&cx->serialize_lock);
	if (cx18_init_on_first_open(cx)) {
		CX18_ERR("Failed to initialize on minor %d\n",
			 video_dev->minor);
		mutex_unlock(&cx->serialize_lock);
		return -ENXIO;
	}
	res = cx18_serialized_open(s, filp);
	mutex_unlock(&cx->serialize_lock);
	return res;
}
Ejemplo n.º 5
0
int cx18_firmware_init(struct cx18 *cx)
{
    /* Allow chip to control CLKRUN */
    write_reg(0x5, CX18_DSP0_INTERRUPT_MASK);

    write_reg(0x000F000F, CX18_PROC_SOFT_RESET); /* stop the fw */

    cx18_msleep_timeout(1, 0);

    sw1_irq_enable(IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU);
    sw2_irq_enable(IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);

    /* Only if the processor is not running */
    if (read_reg(CX18_PROC_SOFT_RESET) & 8) {
        int sz = load_apu_fw_direct("v4l-cx23418-apu.fw",
                   cx->enc_mem, cx, CX18_FW_APU_SIZE);

        sz = sz <= 0 ? sz : load_cpu_fw_direct("v4l-cx23418-cpu.fw",
                    cx->enc_mem, cx, CX18_FW_CPU_SIZE);

        if (sz > 0) {
            int retries = 0;

            /* start the CPU */
            write_reg(0x00080000, CX18_PROC_SOFT_RESET);
            while (retries++ < 50) { /* Loop for max 500mS */
                if ((read_reg(CX18_PROC_SOFT_RESET) & 1) == 0)
                    break;
                cx18_msleep_timeout(10, 0);
            }
            cx18_msleep_timeout(200, 0);
            if (retries == 51) {
                CX18_ERR("Could not start the CPU\n");
                return -EIO;
            }
        }
        if (sz <= 0)
            return -EIO;
    }
    /* initialize GPIO */
    write_reg(0x14001400, 0xC78110);
    return 0;
}
Ejemplo n.º 6
0
int cx18_v4l2_open(struct inode *inode, struct file *filp)
{
    int res, x, y = 0;
    struct cx18 *cx = NULL;
    struct cx18_stream *s = NULL;
    int minor = iminor(inode);

    /* Find which card this open was on */
    spin_lock(&cx18_cards_lock);
    for (x = 0; cx == NULL && x < cx18_cards_active; x++) {
        /* find out which stream this open was on */
        for (y = 0; y < CX18_MAX_STREAMS; y++) {
            if (cx18_cards[x] == NULL)
                continue;
            s = &cx18_cards[x]->streams[y];
            if (s->v4l2dev && s->v4l2dev->minor == minor) {
                cx = cx18_cards[x];
                break;
            }
        }
    }
    spin_unlock(&cx18_cards_lock);

    if (cx == NULL) {
        /* Couldn't find a device registered
           on that minor, shouldn't happen! */
        printk(KERN_WARNING "No cx18 device found on minor %d\n",
               minor);
        return -ENXIO;
    }

    mutex_lock(&cx->serialize_lock);
    if (cx18_init_on_first_open(cx)) {
        CX18_ERR("Failed to initialize on minor %d\n", minor);
        mutex_unlock(&cx->serialize_lock);
        return -ENXIO;
    }
    res = cx18_serialized_open(s, filp);
    mutex_unlock(&cx->serialize_lock);
    return res;
}
Ejemplo n.º 7
0
int cx18_call_i2c_client(struct cx18 *cx, int addr, unsigned cmd, void *arg)
{
	struct i2c_client *client;
	int retval;
	int i;

	CX18_DEBUG_I2C("call_i2c_client addr=%02x\n", addr);
	for (i = 0; i < I2C_CLIENTS_MAX; i++) {
		client = cx->i2c_clients[i];
		if (client == NULL || client->driver == NULL ||
				client->driver->command == NULL)
			continue;
		if (addr == client->addr) {
			retval = client->driver->command(client, cmd, arg);
			return retval;
		}
	}
	if (cmd != VIDIOC_G_CHIP_IDENT)
		CX18_ERR("i2c addr 0x%02x not found for cmd 0x%x!\n",
			       addr, cmd);
	return -ENODEV;
}
Ejemplo n.º 8
0
/* All the DVB attach calls go here, this function get's modified
 * for each new card. No other function in this file needs
 * to change.
 */
static int dvb_register(struct cx18_stream *stream)
{
	struct cx18_dvb *dvb = &stream->dvb;
	struct cx18 *cx = stream->cx;
	int ret = 0;

	switch (cx->card->type) {
	case CX18_CARD_HVR_1600_ESMT:
	case CX18_CARD_HVR_1600_SAMSUNG:
		dvb->fe = dvb_attach(s5h1409_attach,
			&hauppauge_hvr1600_config,
			&cx->i2c_adap[0]);
		if (dvb->fe != NULL) {
			dvb_attach(mxl5005s_attach, dvb->fe,
				&cx->i2c_adap[0],
				&hauppauge_hvr1600_tuner);
			ret = 0;
		}
		break;
	default:
		/* No Digital Tv Support */
		break;
	}

	if (dvb->fe == NULL) {
		CX18_ERR("frontend initialization failed\n");
		return -1;
	}

	ret = dvb_register_frontend(&dvb->dvb_adapter, dvb->fe);
	if (ret < 0) {
		if (dvb->fe->ops.release)
			dvb->fe->ops.release(dvb->fe);
		return ret;
	}

	return ret;
}
Ejemplo n.º 9
0
static void cx18_process_options(struct cx18 *cx)
{
	int i, j;

	cx->options.megabytes[CX18_ENC_STREAM_TYPE_TS] = enc_ts_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_MPG] = enc_mpg_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_IDX] = enc_idx_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_YUV] = enc_yuv_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_VBI] = enc_vbi_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_PCM] = enc_pcm_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_RAD] = 0; /* control only */

	cx->stream_buffers[CX18_ENC_STREAM_TYPE_TS] = enc_ts_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_MPG] = enc_mpg_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_IDX] = enc_idx_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_YUV] = enc_yuv_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_VBI] = enc_vbi_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_PCM] = enc_pcm_bufs;
	cx->stream_buffers[CX18_ENC_STREAM_TYPE_RAD] = 0; /* control, no data */

	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_TS] = enc_ts_bufsize;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_MPG] = enc_mpg_bufsize;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_IDX] = enc_idx_bufsize;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_YUV] = enc_yuv_bufsize;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_VBI] = vbi_active_samples * 36;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_PCM] = enc_pcm_bufsize;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_RAD] = 0; /* control no data */

	/* Ensure stream_buffers & stream_buf_size are valid */
	for (i = 0; i < CX18_MAX_STREAMS; i++) {
		if (cx->stream_buffers[i] == 0 ||     /* User said 0 buffers */
		    cx->options.megabytes[i] <= 0 ||  /* User said 0 MB total */
		    cx->stream_buf_size[i] <= 0) {    /* User said buf size 0 */
			cx->options.megabytes[i] = 0;
			cx->stream_buffers[i] = 0;
			cx->stream_buf_size[i] = 0;
			continue;
		}
		/*
		 * YUV is a special case where the stream_buf_size needs to be
		 * an integral multiple of 33.75 kB (storage for 32 screens
		 * lines to maintain alignment in case of lost buffers).
		 *
		 * IDX is a special case where the stream_buf_size should be
		 * an integral multiple of 1.5 kB (storage for 64 index entries
		 * to maintain alignment in case of lost buffers).
		 *
		 */
		if (i == CX18_ENC_STREAM_TYPE_YUV) {
			cx->stream_buf_size[i] *= 1024;
			cx->stream_buf_size[i] -=
			   (cx->stream_buf_size[i] % CX18_UNIT_ENC_YUV_BUFSIZE);

			if (cx->stream_buf_size[i] < CX18_UNIT_ENC_YUV_BUFSIZE)
				cx->stream_buf_size[i] =
						CX18_UNIT_ENC_YUV_BUFSIZE;
		} else if (i == CX18_ENC_STREAM_TYPE_IDX) {
			cx->stream_buf_size[i] *= 1024;
			cx->stream_buf_size[i] -=
			   (cx->stream_buf_size[i] % CX18_UNIT_ENC_IDX_BUFSIZE);

			if (cx->stream_buf_size[i] < CX18_UNIT_ENC_IDX_BUFSIZE)
				cx->stream_buf_size[i] =
						CX18_UNIT_ENC_IDX_BUFSIZE;
		}
		/*
		 * YUV and IDX are special cases where the stream_buf_size is
		 * now in bytes.
		 * VBI is a special case where the stream_buf_size is fixed
		 * and already in bytes
		 */
		if (i == CX18_ENC_STREAM_TYPE_VBI ||
		    i == CX18_ENC_STREAM_TYPE_YUV ||
		    i == CX18_ENC_STREAM_TYPE_IDX) {
			if (cx->stream_buffers[i] < 0) {
				cx->stream_buffers[i] =
					cx->options.megabytes[i] * 1024 * 1024
					/ cx->stream_buf_size[i];
			} else {
				/* N.B. This might round down to 0 */
				cx->options.megabytes[i] =
					cx->stream_buffers[i]
					* cx->stream_buf_size[i]/(1024 * 1024);
			}
		} else {
			/* All other streams have stream_buf_size in kB here */
			if (cx->stream_buffers[i] < 0) {
				cx->stream_buffers[i] =
						cx->options.megabytes[i] * 1024
						/ cx->stream_buf_size[i];
			} else {
				/* N.B. This might round down to 0 */
				cx->options.megabytes[i] =
						cx->stream_buffers[i]
						* cx->stream_buf_size[i] / 1024;
			}
			/* convert from kB to bytes */
			cx->stream_buf_size[i] *= 1024;
		}
		CX18_DEBUG_INFO("Stream type %d options: %d MB, %d buffers, "
				"%d bytes\n", i, cx->options.megabytes[i],
				cx->stream_buffers[i], cx->stream_buf_size[i]);
	}

	cx->options.cardtype = cardtype[cx->instance];
	cx->options.tuner = tuner[cx->instance];
	cx->options.radio = radio[cx->instance];

	cx->std = cx18_parse_std(cx);
	if (cx->options.cardtype == -1) {
		CX18_INFO("Ignore card\n");
		return;
	}
	cx->card = cx18_get_card(cx->options.cardtype - 1);
	if (cx->card)
		CX18_INFO("User specified %s card\n", cx->card->name);
	else if (cx->options.cardtype != 0)
		CX18_ERR("Unknown user specified type, trying to autodetect card\n");
	if (cx->card == NULL) {
		if (cx->pci_dev->subsystem_vendor == CX18_PCI_ID_HAUPPAUGE) {
			cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
			CX18_INFO("Autodetected Hauppauge card\n");
		}
	}
	if (cx->card == NULL) {
		for (i = 0; (cx->card = cx18_get_card(i)); i++) {
			if (cx->card->pci_list == NULL)
				continue;
			for (j = 0; cx->card->pci_list[j].device; j++) {
				if (cx->pci_dev->device !=
				    cx->card->pci_list[j].device)
					continue;
				if (cx->pci_dev->subsystem_vendor !=
				    cx->card->pci_list[j].subsystem_vendor)
					continue;
				if (cx->pci_dev->subsystem_device !=
				    cx->card->pci_list[j].subsystem_device)
					continue;
				CX18_INFO("Autodetected %s card\n", cx->card->name);
				goto done;
			}
		}
	}
done:

	if (cx->card == NULL) {
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		CX18_ERR("Unknown card: vendor/device: [%04x:%04x]\n",
			 cx->pci_dev->vendor, cx->pci_dev->device);
		CX18_ERR("              subsystem vendor/device: [%04x:%04x]\n",
			 cx->pci_dev->subsystem_vendor,
			 cx->pci_dev->subsystem_device);
		CX18_ERR("Defaulting to %s card\n", cx->card->name);
		CX18_ERR("Please mail the vendor/device and subsystem vendor/device IDs and what kind of\n");
		CX18_ERR("card you have to the ivtv-devel mailinglist (www.ivtvdriver.org)\n");
		CX18_ERR("Prefix your subject line with [UNKNOWN CX18 CARD].\n");
	}
	cx->v4l2_cap = cx->card->v4l2_capabilities;
	cx->card_name = cx->card->name;
	cx->card_i2c = cx->card->i2c;
}
Ejemplo n.º 10
0
static void cx18_process_eeprom(struct cx18 *cx)
{
	struct tveeprom tv;

	cx18_read_eeprom(cx, &tv);

	/* Many thanks to Steven Toth from Hauppauge for providing the
	   model numbers */
	/* Note: the Samsung memory models cannot be reliably determined
	   from the model number. Use the cardtype module option if you
	   have one of these preproduction models. */
	switch (tv.model) {
	case 74301: /* Retail models */
	case 74321:
	case 74351: /* OEM models */
	case 74361:
		/* Digital side is s5h1411/tda18271 */
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_S5H1411);
		break;
	case 74021: /* Retail models */
	case 74031:
	case 74041:
	case 74141:
	case 74541: /* OEM models */
	case 74551:
	case 74591:
	case 74651:
	case 74691:
	case 74751:
	case 74891:
		/* Digital side is s5h1409/mxl5005s */
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		break;
	case 0x718:
		return;
	case 0xffffffff:
		CX18_INFO("Unknown EEPROM encoding\n");
		return;
	case 0:
		CX18_ERR("Invalid EEPROM\n");
		return;
	default:
		CX18_ERR("Unknown model %d, defaulting to original HVR-1600 "
			 "(cardtype=1)\n", tv.model);
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		break;
	}

	cx->v4l2_cap = cx->card->v4l2_capabilities;
	cx->card_name = cx->card->name;
	cx->card_i2c = cx->card->i2c;

	CX18_INFO("Autodetected %s\n", cx->card_name);

	if (tv.tuner_type == TUNER_ABSENT)
		CX18_ERR("tveeprom cannot autodetect tuner!\n");

	if (cx->options.tuner == -1)
		cx->options.tuner = tv.tuner_type;
	if (cx->options.radio == -1)
		cx->options.radio = (tv.has_radio != 0);

	if (cx->std != 0)
		/* user specified tuner standard */
		return;

	/* autodetect tuner standard */
#define TVEEPROM_TUNER_FORMAT_ALL (V4L2_STD_B  | V4L2_STD_GH | \
				   V4L2_STD_MN | \
				   V4L2_STD_PAL_I | \
				   V4L2_STD_SECAM_L | V4L2_STD_SECAM_LC | \
				   V4L2_STD_DK)
	if ((tv.tuner_formats & TVEEPROM_TUNER_FORMAT_ALL)
					== TVEEPROM_TUNER_FORMAT_ALL) {
		CX18_DEBUG_INFO("Worldwide tuner detected\n");
		cx->std = V4L2_STD_ALL;
	} else if (tv.tuner_formats & V4L2_STD_PAL) {
		CX18_DEBUG_INFO("PAL tuner detected\n");
		cx->std |= V4L2_STD_PAL_BG | V4L2_STD_PAL_H;
	} else if (tv.tuner_formats & V4L2_STD_NTSC) {
		CX18_DEBUG_INFO("NTSC tuner detected\n");
		cx->std |= V4L2_STD_NTSC_M;
	} else if (tv.tuner_formats & V4L2_STD_SECAM) {
		CX18_DEBUG_INFO("SECAM tuner detected\n");
		cx->std |= V4L2_STD_SECAM_L;
	} else {
		CX18_INFO("No tuner detected, default to NTSC-M\n");
		cx->std |= V4L2_STD_NTSC_M;
	}
}
Ejemplo n.º 11
0
static int cx18_api_call(struct cx18 *cx, u32 cmd, int args, u32 data[])
{
	const struct cx18_api_info *info = find_api_info(cmd);
	u32 state = 0, irq = 0, req, oldreq, err;
	struct cx18_mailbox __iomem *mb;
	wait_queue_head_t *waitq;
	int timeout = 100;
	int cnt = 0;
	int sig = 0;
	int i;

	if (info == NULL) {
		CX18_WARN("unknown cmd %x\n", cmd);
		return -EINVAL;
	}

	if (cmd == CX18_CPU_DE_SET_MDL)
		CX18_DEBUG_HI_API("%s\n", info->name);
	else
		CX18_DEBUG_API("%s\n", info->name);
	cx18_setup_page(cx, SCB_OFFSET);
	mb = cx18_mb_is_complete(cx, info->rpu, &state, &irq, &req);

	if (mb == NULL) {
		CX18_ERR("mb %s busy\n", info->name);
		return -EBUSY;
	}

	oldreq = req - 1;
	cx18_writel(cx, cmd, &mb->cmd);
	for (i = 0; i < args; i++)
		cx18_writel(cx, data[i], &mb->args[i]);
	cx18_writel(cx, 0, &mb->error);
	cx18_writel(cx, req, &mb->request);

	switch (info->rpu) {
	case APU: waitq = &cx->mb_apu_waitq; break;
	case CPU: waitq = &cx->mb_cpu_waitq; break;
	case EPU: waitq = &cx->mb_epu_waitq; break;
	case HPU: waitq = &cx->mb_hpu_waitq; break;
	default: return -EINVAL;
	}
	if (info->flags & API_FAST)
		timeout /= 2;
	cx18_write_reg(cx, irq, SW1_INT_SET);

	while (!sig && cx18_readl(cx, &mb->ack) != cx18_readl(cx, &mb->request)
	       && cnt < 660) {
		if (cnt > 200 && !in_atomic())
			sig = cx18_msleep_timeout(10, 1);
		cnt++;
	}
	if (sig)
		return -EINTR;
	if (cnt == 660) {
		cx18_writel(cx, oldreq, &mb->request);
		CX18_ERR("mb %s failed\n", info->name);
		return -EINVAL;
	}
	for (i = 0; i < MAX_MB_ARGUMENTS; i++)
		data[i] = cx18_readl(cx, &mb->args[i]);
	err = cx18_readl(cx, &mb->error);
	if (!in_atomic() && (info->flags & API_SLOW))
		cx18_msleep_timeout(300, 0);
	if (err)
		CX18_DEBUG_API("mailbox error %08x for command %s\n", err,
				info->name);
	return err ? -EIO : 0;
}
Ejemplo n.º 12
0
static int __devinit cx18_probe(struct pci_dev *pci_dev,
				const struct pci_device_id *pci_id)
{
	int retval = 0;
	int i;
	u32 devtype;
	struct cx18 *cx;

	
	i = atomic_inc_return(&cx18_instance) - 1;
	if (i >= CX18_MAX_CARDS) {
		printk(KERN_ERR "cx18: cannot manage card %d, driver has a "
		       "limit of 0 - %d\n", i, CX18_MAX_CARDS - 1);
		return -ENOMEM;
	}

	cx = kzalloc(sizeof(struct cx18), GFP_ATOMIC);
	if (cx == NULL) {
		printk(KERN_ERR "cx18: cannot manage card %d, out of memory\n",
		       i);
		return -ENOMEM;
	}
	cx->pci_dev = pci_dev;
	cx->instance = i;

	retval = v4l2_device_register(&pci_dev->dev, &cx->v4l2_dev);
	if (retval) {
		printk(KERN_ERR "cx18: v4l2_device_register of card %d failed"
		       "\n", cx->instance);
		kfree(cx);
		return retval;
	}
	snprintf(cx->v4l2_dev.name, sizeof(cx->v4l2_dev.name), "cx18-%d",
		 cx->instance);
	CX18_INFO("Initializing card %d\n", cx->instance);

	cx18_process_options(cx);
	if (cx->options.cardtype == -1) {
		retval = -ENODEV;
		goto err;
	}

	retval = cx18_init_struct1(cx);
	if (retval)
		goto err;

	CX18_DEBUG_INFO("base addr: 0x%08x\n", cx->base_addr);

	
	retval = cx18_setup_pci(cx, pci_dev, pci_id);
	if (retval != 0)
		goto free_workqueues;

	
	CX18_DEBUG_INFO("attempting ioremap at 0x%08x len 0x%08x\n",
		   cx->base_addr + CX18_MEM_OFFSET, CX18_MEM_SIZE);
	cx->enc_mem = ioremap_nocache(cx->base_addr + CX18_MEM_OFFSET,
				       CX18_MEM_SIZE);
	if (!cx->enc_mem) {
		CX18_ERR("ioremap failed, perhaps increasing __VMALLOC_RESERVE in page.h\n");
		CX18_ERR("or disabling CONFIG_HIGHMEM4G into the kernel would help\n");
		retval = -ENOMEM;
		goto free_mem;
	}
	cx->reg_mem = cx->enc_mem + CX18_REG_OFFSET;
	devtype = cx18_read_reg(cx, 0xC72028);
	switch (devtype & 0xff000000) {
	case 0xff000000:
		CX18_INFO("cx23418 revision %08x (A)\n", devtype);
		break;
	case 0x01000000:
		CX18_INFO("cx23418 revision %08x (B)\n", devtype);
		break;
	default:
		CX18_INFO("cx23418 revision %08x (Unknown)\n", devtype);
		break;
	}

	cx18_init_power(cx, 1);
	cx18_init_memory(cx);

	cx->scb = (struct cx18_scb __iomem *)(cx->enc_mem + SCB_OFFSET);
	cx18_init_scb(cx);

	cx18_gpio_init(cx);

	
	retval = cx18_av_probe(cx);
	if (retval) {
		CX18_ERR("Could not register A/V decoder subdevice\n");
		goto free_map;
	}
	cx18_call_hw(cx, CX18_HW_418_AV, core, init, 0);

	
	if (cx->card->hw_all & CX18_HW_GPIO_RESET_CTRL) {
		if (cx18_gpio_register(cx, CX18_HW_GPIO_RESET_CTRL) != 0)
			CX18_WARN("Could not register GPIO reset controller"
				  "subdevice; proceeding anyway.\n");
		else
			cx->hw_flags |= CX18_HW_GPIO_RESET_CTRL;
	}

	
	CX18_DEBUG_INFO("activating i2c...\n");
	retval = init_cx18_i2c(cx);
	if (retval) {
		CX18_ERR("Could not initialize i2c\n");
		goto free_map;
	}

	if (cx->card->hw_all & CX18_HW_TVEEPROM) {
		
		cx18_process_eeprom(cx);
	}
	if (cx->card->comment)
		CX18_INFO("%s", cx->card->comment);
	if (cx->card->v4l2_capabilities == 0) {
		retval = -ENODEV;
		goto free_i2c;
	}
	cx18_init_memory(cx);
	cx18_init_scb(cx);

	
	retval = request_irq(cx->pci_dev->irq, cx18_irq_handler,
			     IRQF_SHARED | IRQF_DISABLED,
			     cx->v4l2_dev.name, (void *)cx);
	if (retval) {
		CX18_ERR("Failed to register irq %d\n", retval);
		goto free_i2c;
	}

	if (cx->std == 0)
		cx->std = V4L2_STD_NTSC_M;

	if (cx->options.tuner == -1) {
		for (i = 0; i < CX18_CARD_MAX_TUNERS; i++) {
			if ((cx->std & cx->card->tuners[i].std) == 0)
				continue;
			cx->options.tuner = cx->card->tuners[i].tuner;
			break;
		}
	}
	
	if (cx->options.tuner == -1 && cx->card->tuners[0].std) {
		cx->std = cx->card->tuners[0].std;
		if (cx->std & V4L2_STD_PAL)
			cx->std = V4L2_STD_PAL_BG | V4L2_STD_PAL_H;
		else if (cx->std & V4L2_STD_NTSC)
			cx->std = V4L2_STD_NTSC_M;
		else if (cx->std & V4L2_STD_SECAM)
			cx->std = V4L2_STD_SECAM_L;
		cx->options.tuner = cx->card->tuners[0].tuner;
	}
	if (cx->options.radio == -1)
		cx->options.radio = (cx->card->radio_input.audio_type != 0);

	
	cx18_init_struct2(cx);

	cx18_init_subdevs(cx);

	if (cx->std & V4L2_STD_525_60)
		cx->is_60hz = 1;
	else
		cx->is_50hz = 1;

	cx->params.video_gop_size = cx->is_60hz ? 15 : 12;

	if (cx->options.radio > 0)
		cx->v4l2_cap |= V4L2_CAP_RADIO;

	if (cx->options.tuner > -1) {
		struct tuner_setup setup;

		setup.addr = ADDR_UNSET;
		setup.type = cx->options.tuner;
		setup.mode_mask = T_ANALOG_TV;  
		setup.tuner_callback = (setup.type == TUNER_XC2028) ?
			cx18_reset_tuner_gpio : NULL;
		cx18_call_all(cx, tuner, s_type_addr, &setup);
		if (setup.type == TUNER_XC2028) {
			static struct xc2028_ctrl ctrl = {
				.fname = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
			};
			struct v4l2_priv_tun_config cfg = {
				.tuner = cx->options.tuner,
				.priv = &ctrl,
			};
			cx18_call_all(cx, tuner, s_config, &cfg);
		}
	}

	
	cx->tuner_std = cx->std;

	retval = cx18_streams_setup(cx);
	if (retval) {
		CX18_ERR("Error %d setting up streams\n", retval);
		goto free_irq;
	}
	retval = cx18_streams_register(cx);
	if (retval) {
		CX18_ERR("Error %d registering devices\n", retval);
		goto free_streams;
	}

	CX18_INFO("Initialized card: %s\n", cx->card_name);
	return 0;

free_streams:
	cx18_streams_cleanup(cx, 1);
free_irq:
	free_irq(cx->pci_dev->irq, (void *)cx);
free_i2c:
	exit_cx18_i2c(cx);
free_map:
	cx18_iounmap(cx);
free_mem:
	release_mem_region(cx->base_addr, CX18_MEM_SIZE);
free_workqueues:
	destroy_workqueue(cx->in_work_queue);
	destroy_workqueue(cx->out_work_queue);
err:
	if (retval == 0)
		retval = -ENODEV;
	CX18_ERR("Error %d on initialization\n", retval);

	v4l2_device_unregister(&cx->v4l2_dev);
	kfree(cx);
	return retval;
}

int cx18_init_on_first_open(struct cx18 *cx)
{
	int video_input;
	int fw_retry_count = 3;
	struct v4l2_frequency vf;
	struct cx18_open_id fh;

	fh.cx = cx;

	if (test_bit(CX18_F_I_FAILED, &cx->i_flags))
		return -ENXIO;

	if (test_and_set_bit(CX18_F_I_INITED, &cx->i_flags))
		return 0;

	while (--fw_retry_count > 0) {
		
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}
	set_bit(CX18_F_I_LOADED_FW, &cx->i_flags);

	

	
	cx18_vapi(cx, CX18_APU_START, 2, CX18_APU_ENCODING_METHOD_MPEG|0xb9, 0);
	cx18_vapi(cx, CX18_APU_RESETAI, 0);
	cx18_vapi(cx, CX18_APU_STOP, 1, CX18_APU_ENCODING_METHOD_MPEG);

	fw_retry_count = 3;
	while (--fw_retry_count > 0) {
		
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}

	

	
	cx18_vapi(cx, CX18_APU_START, 2, CX18_APU_ENCODING_METHOD_MPEG|0xb9, 0);
	cx18_vapi(cx, CX18_APU_RESETAI, 0);
	cx18_vapi(cx, CX18_APU_STOP, 1, CX18_APU_ENCODING_METHOD_MPEG);

	
	v4l2_subdev_call(cx->sd_av, core, load_fw);

	vf.tuner = 0;
	vf.type = V4L2_TUNER_ANALOG_TV;
	vf.frequency = 6400; 

	
	if (cx->std == V4L2_STD_NTSC_M_JP)
		vf.frequency = 1460;	
	else if (cx->std & V4L2_STD_NTSC_M)
		vf.frequency = 1076;	

	video_input = cx->active_input;
	cx->active_input++;	
	cx18_s_input(NULL, &fh, video_input);

	
	cx->std++;		
	cx18_s_std(NULL, &fh, &cx->tuner_std);
	cx18_s_frequency(NULL, &fh, &vf);
	return 0;
}

static void cx18_cancel_in_work_orders(struct cx18 *cx)
{
	int i;
	for (i = 0; i < CX18_MAX_IN_WORK_ORDERS; i++)
		cancel_work_sync(&cx->in_work_order[i].work);
}
int cx18_av_loadfw(struct cx18 *cx)
{
	const struct firmware *fw = NULL;
	u32 size;
	u32 v;
	u8 *ptr;
	int i;

	if (request_firmware(&fw, FWFILE, &cx->dev->dev) != 0) {
		CX18_ERR("unable to open firmware %s\n", FWFILE);
		return -EINVAL;
	}

	cx18_av_write4(cx, CXADEC_CHIP_CTRL, 0x00010000);
	cx18_av_write(cx, CXADEC_STD_DET_CTL, 0xf6); /* Byte 0 */

	/* Reset the Mako core (Register is undocumented.) */
	cx18_av_write4(cx, 0x8100, 0x00010000);

	/* Put the 8051 in reset and enable firmware upload */
	cx18_av_write4(cx, CXADEC_DL_CTL, 0x0F000000);

	ptr = fw->data;
	size = fw->size;

	for (i = 0; i < size; i++) {
		u32 dl_control = 0x0F000000 | ((u32)ptr[i] << 16);
		u32 value = 0;
		int retries;

		for (retries = 0; retries < 5; retries++) {
			cx18_av_write4(cx, CXADEC_DL_CTL, dl_control);
			value = cx18_av_read4(cx, CXADEC_DL_CTL);
			if ((value & 0x3F00) == (dl_control & 0x3F00))
				break;
		}
		if (retries >= 5) {
			CX18_ERR("unable to load firmware %s\n", FWFILE);
			release_firmware(fw);
			return -EIO;
		}
	}

	cx18_av_write4(cx, CXADEC_DL_CTL, 0x13000000 | fw->size);

	/* Output to the 416 */
	cx18_av_and_or4(cx, CXADEC_PIN_CTRL1, ~0, 0x78000);

	/* Audio input control 1 set to Sony mode */
	/* Audio output input 2 is 0 for slave operation input */
	/* 0xC4000914[5]: 0 = left sample on WS=0, 1 = left sample on WS=1 */
	/* 0xC4000914[7]: 0 = Philips mode, 1 = Sony mode (1st SCK rising edge
	   after WS transition for first bit of audio word. */
	cx18_av_write4(cx, CXADEC_I2S_IN_CTL, 0x000000A0);

	/* Audio output control 1 is set to Sony mode */
	/* Audio output control 2 is set to 1 for master mode */
	/* 0xC4000918[5]: 0 = left sample on WS=0, 1 = left sample on WS=1 */
	/* 0xC4000918[7]: 0 = Philips mode, 1 = Sony mode (1st SCK rising edge
	   after WS transition for first bit of audio word. */
	/* 0xC4000918[8]: 0 = slave operation, 1 = master (SCK_OUT and WS_OUT
	   are generated) */
	cx18_av_write4(cx, CXADEC_I2S_OUT_CTL, 0x000001A0);

	/* set alt I2s master clock to /16 and enable alt divider i2s
	   passthrough */
	cx18_av_write4(cx, CXADEC_PIN_CFG3, 0x5000B687);

	cx18_av_write4(cx, CXADEC_STD_DET_CTL, 0x000000F6);
	/* CxDevWrReg(CXADEC_STD_DET_CTL, 0x000000FF); */

	/* Set bit 0 in register 0x9CC to signify that this is MiniMe. */
	/* Register 0x09CC is defined by the Merlin firmware, and doesn't
	   have a name in the spec. */
	cx18_av_write4(cx, 0x09CC, 1);

#define CX18_AUDIO_ENABLE            	0xc72014
	v = read_reg(CX18_AUDIO_ENABLE);
	/* If bit 11 is 1 */
	if (v & 0x800)
		write_reg(v & 0xFFFFFBFF, CX18_AUDIO_ENABLE); /* Clear bit 10 */

	/* Enable WW auto audio standard detection */
	v = cx18_av_read4(cx, CXADEC_STD_DET_CTL);
	v |= 0xFF;   /* Auto by default */
	v |= 0x400;  /* Stereo by default */
	v |= 0x14000000;
	cx18_av_write4(cx, CXADEC_STD_DET_CTL, v);

	release_firmware(fw);

	CX18_INFO("loaded %s firmware (%d bytes)\n", FWFILE, size);
	return 0;
}
Ejemplo n.º 14
0
static void cx18_process_options(struct cx18 *cx)
{
	int i, j;

	cx->options.megabytes[CX18_ENC_STREAM_TYPE_MPG] = enc_mpg_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_TS] = enc_ts_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_YUV] = enc_yuv_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_VBI] = enc_vbi_buffers;
	cx->options.megabytes[CX18_ENC_STREAM_TYPE_PCM] = enc_pcm_buffers;
	cx->options.cardtype = cardtype[cx->num];
	cx->options.tuner = tuner[cx->num];
	cx->options.radio = radio[cx->num];

	cx->std = cx18_parse_std(cx);
	if (cx->options.cardtype == -1) {
		CX18_INFO("Ignore card\n");
		return;
	}
	cx->card = cx18_get_card(cx->options.cardtype - 1);
	if (cx->card)
		CX18_INFO("User specified %s card\n", cx->card->name);
	else if (cx->options.cardtype != 0)
		CX18_ERR("Unknown user specified type, trying to autodetect card\n");
	if (cx->card == NULL) {
		if (cx->dev->subsystem_vendor == CX18_PCI_ID_HAUPPAUGE) {
			cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
			CX18_INFO("Autodetected Hauppauge card\n");
		}
	}
	if (cx->card == NULL) {
		for (i = 0; (cx->card = cx18_get_card(i)); i++) {
			if (cx->card->pci_list == NULL)
				continue;
			for (j = 0; cx->card->pci_list[j].device; j++) {
				if (cx->dev->device !=
				    cx->card->pci_list[j].device)
					continue;
				if (cx->dev->subsystem_vendor !=
				    cx->card->pci_list[j].subsystem_vendor)
					continue;
				if (cx->dev->subsystem_device !=
				    cx->card->pci_list[j].subsystem_device)
					continue;
				CX18_INFO("Autodetected %s card\n", cx->card->name);
				goto done;
			}
		}
	}
done:

	if (cx->card == NULL) {
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		CX18_ERR("Unknown card: vendor/device: %04x/%04x\n",
		     cx->dev->vendor, cx->dev->device);
		CX18_ERR("              subsystem vendor/device: %04x/%04x\n",
		     cx->dev->subsystem_vendor, cx->dev->subsystem_device);
		CX18_ERR("Defaulting to %s card\n", cx->card->name);
		CX18_ERR("Please mail the vendor/device and subsystem vendor/device IDs and what kind of\n");
		CX18_ERR("card you have to the ivtv-devel mailinglist (www.ivtvdriver.org)\n");
		CX18_ERR("Prefix your subject line with [UNKNOWN CX18 CARD].\n");
	}
	cx->v4l2_cap = cx->card->v4l2_capabilities;
	cx->card_name = cx->card->name;
	cx->card_i2c = cx->card->i2c;
}
static int cx18_prep_dev(struct cx18 *cx, int type)
{
	struct cx18_stream *s = &cx->streams[type];
	u32 cap = cx->v4l2_cap;
	int num_offset = cx18_stream_info[type].num_offset;
	int num = cx->instance + cx18_first_minor + num_offset;

	s->video_dev = NULL;
	s->dvb = NULL;
	s->cx = cx;
	s->type = type;
	s->name = cx18_stream_info[type].name;

	
	if (type == CX18_ENC_STREAM_TYPE_RAD && !(cap & V4L2_CAP_RADIO))
		return 0;

	
	if (type == CX18_ENC_STREAM_TYPE_VBI &&
	    !(cap & (V4L2_CAP_VBI_CAPTURE | V4L2_CAP_SLICED_VBI_CAPTURE)))
		return 0;

	if (cx18_stream_info[type].dma != PCI_DMA_NONE &&
	    cx->stream_buffers[type] == 0) {
		CX18_INFO("Disabled %s device\n", cx18_stream_info[type].name);
		return 0;
	}

	cx18_stream_init(cx, type);

	
	if (type == CX18_ENC_STREAM_TYPE_TS) {
		if (cx->card->hw_all & CX18_HW_DVB) {
			s->dvb = kzalloc(sizeof(struct cx18_dvb), GFP_KERNEL);
			if (s->dvb == NULL) {
				CX18_ERR("Couldn't allocate cx18_dvb structure"
					 " for %s\n", s->name);
				return -ENOMEM;
			}
		} else {
			
			s->buffers = 0;
		}
	}

	if (num_offset == -1)
		return 0;

	
	s->video_dev = video_device_alloc();
	if (s->video_dev == NULL) {
		CX18_ERR("Couldn't allocate v4l2 video_device for %s\n",
				s->name);
		return -ENOMEM;
	}

	snprintf(s->video_dev->name, sizeof(s->video_dev->name), "%s %s",
		 cx->v4l2_dev.name, s->name);

	s->video_dev->num = num;
	s->video_dev->v4l2_dev = &cx->v4l2_dev;
	s->video_dev->fops = &cx18_v4l2_enc_fops;
	s->video_dev->release = video_device_release;
	s->video_dev->tvnorms = V4L2_STD_ALL;
	set_bit(V4L2_FL_USE_FH_PRIO, &s->video_dev->flags);
	cx18_set_funcs(s->video_dev);
	return 0;
}
Ejemplo n.º 16
0
static void cx18_process_eeprom(struct cx18 *cx)
{
	struct tveeprom tv;

	cx18_read_eeprom(cx, &tv);

	/* Many thanks to Steven Toth from Hauppauge for providing the
	   model numbers */
	/* Note: the Samsung memory models cannot be reliably determined
	   from the model number. Use the cardtype module option if you
	   have one of these preproduction models. */
	switch (tv.model) {
	case 74000 ... 74999:
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		break;
	case 0x718:
		return;
	case 0xffffffff:
		CX18_INFO("Unknown EEPROM encoding\n");
		return;
	case 0:
		CX18_ERR("Invalid EEPROM\n");
		return;
	default:
		CX18_ERR("Unknown model %d, defaulting to HVR-1600\n", tv.model);
		cx->card = cx18_get_card(CX18_CARD_HVR_1600_ESMT);
		break;
	}

	cx->v4l2_cap = cx->card->v4l2_capabilities;
	cx->card_name = cx->card->name;
	cx->card_i2c = cx->card->i2c;

	CX18_INFO("Autodetected %s\n", cx->card_name);

	if (tv.tuner_type == TUNER_ABSENT)
		CX18_ERR("tveeprom cannot autodetect tuner!\n");

	if (cx->options.tuner == -1)
		cx->options.tuner = tv.tuner_type;
	if (cx->options.radio == -1)
		cx->options.radio = (tv.has_radio != 0);

	if (cx->std != 0)
		/* user specified tuner standard */
		return;

	/* autodetect tuner standard */
	if (tv.tuner_formats & V4L2_STD_PAL) {
		CX18_DEBUG_INFO("PAL tuner detected\n");
		cx->std |= V4L2_STD_PAL_BG | V4L2_STD_PAL_H;
	} else if (tv.tuner_formats & V4L2_STD_NTSC) {
		CX18_DEBUG_INFO("NTSC tuner detected\n");
		cx->std |= V4L2_STD_NTSC_M;
	} else if (tv.tuner_formats & V4L2_STD_SECAM) {
		CX18_DEBUG_INFO("SECAM tuner detected\n");
		cx->std |= V4L2_STD_SECAM_L;
	} else {
		CX18_INFO("No tuner detected, default to NTSC-M\n");
		cx->std |= V4L2_STD_NTSC_M;
	}
}
Ejemplo n.º 17
0
static int load_apu_fw_direct(const char *fn, u8 __iomem *dst, struct cx18 *cx, long size)
{
    const struct firmware *fw = NULL;
    int retries = 3;
    int i, j;
    const u32 *src;
    struct cx18_apu_rom_seghdr seghdr;
    const u8 *vers;
    u32 offset = 0;
    u32 apu_version = 0;
    int sz;

retry:
    if (!retries || request_firmware(&fw, fn, &cx->dev->dev)) {
        CX18_ERR("unable to open firmware %s (must be %ld bytes)\n",
                fn, size);
        CX18_ERR("did you put the firmware in the hotplug firmware directory?\n");
        return -ENOMEM;
    }

    src = (const u32 *)fw->data;
    vers = fw->data + sizeof(seghdr);
    sz = fw->size;

    if (fw->size != size) {
        /* Due to race conditions in firmware loading (esp. with
           udev <0.95) the wrong file was sometimes loaded. So we check
           filesizes to see if at least the right-sized file was
           loaded. If not, then we retry. */
        CX18_INFO("retry: file loaded was not %s (expected size %ld, got %zd)\n",
                   fn, size, fw->size);
        release_firmware(fw);
        retries--;
        goto retry;
    }
    apu_version = (vers[0] << 24) | (vers[4] << 16) | vers[32];
    while (offset + sizeof(seghdr) < size) {
        /* TODO: byteswapping */
        memcpy(&seghdr, src + offset / 4, sizeof(seghdr));
        offset += sizeof(seghdr);
        if (seghdr.sync1 != APU_ROM_SYNC1 ||
            seghdr.sync2 != APU_ROM_SYNC2) {
            offset += seghdr.size;
            continue;
        }
        CX18_DEBUG_INFO("load segment %x-%x\n", seghdr.addr,
                seghdr.addr + seghdr.size - 1);
        if (offset + seghdr.size > sz)
            break;
        for (i = 0; i < seghdr.size; i += 4096) {
            setup_page(offset + i);
            for (j = i; j < seghdr.size && j < i + 4096; j += 4) {
                /* no need for endianness conversion on the ppc */
                __raw_writel(src[(offset + j) / 4], dst + seghdr.addr + j);
                if (__raw_readl(dst + seghdr.addr + j) != src[(offset + j) / 4]) {
                    CX18_ERR("Mismatch at offset %x\n", offset + j);
                    release_firmware(fw);
                    return -EIO;
                }
            }
        }
        offset += seghdr.size;
    }
    if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
        CX18_INFO("loaded %s firmware V%08x (%zd bytes)\n",
                fn, apu_version, fw->size);
    release_firmware(fw);
    /* Clear bit0 for APU to start from 0 */
    write_reg(read_reg(0xc72030) & ~1, 0xc72030);
    return size;
}
int cx18_firmware_init(struct cx18 *cx)
{
	u32 fw_entry_addr;
	int sz, retries;
	u32 api_args[MAX_MB_ARGUMENTS];

	/* Allow chip to control CLKRUN */
	cx18_write_reg(cx, 0x5, CX18_DSP0_INTERRUPT_MASK);

	/* Stop the firmware */
	cx18_write_reg_expect(cx, 0x000F000F, CX18_PROC_SOFT_RESET,
				  0x0000000F, 0x000F000F);

	cx18_msleep_timeout(1, 0);

	/* If the CPU is still running */
	if ((cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 8) == 0) {
		CX18_ERR("%s: couldn't stop CPU to load firmware\n", __func__);
		return -EIO;
	}

	cx18_sw1_irq_enable(cx, IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU);
	cx18_sw2_irq_enable(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);

	sz = load_cpu_fw_direct("v4l-cx23418-cpu.fw", cx->enc_mem, cx);
	if (sz <= 0)
		return sz;

	/* The SCB & IPC area *must* be correct before starting the firmwares */
	cx18_init_scb(cx);

	fw_entry_addr = 0;
	sz = load_apu_fw_direct("v4l-cx23418-apu.fw", cx->enc_mem, cx,
				&fw_entry_addr);
	if (sz <= 0)
		return sz;

	/* Start the CPU. The CPU will take care of the APU for us. */
	cx18_write_reg_expect(cx, 0x00080000, CX18_PROC_SOFT_RESET,
				  0x00000000, 0x00080008);

	/* Wait up to 500 ms for the APU to come out of reset */
	for (retries = 0;
	     retries < 50 && (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1;
	     retries++)
		cx18_msleep_timeout(10, 0);

	cx18_msleep_timeout(200, 0);

	if (retries == 50 &&
	    (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1) {
		CX18_ERR("Could not start the CPU\n");
		return -EIO;
	}

	/*
	 * The CPU had once before set up to receive an interrupt for it's
	 * outgoing IRQ_CPU_TO_EPU_ACK to us.  If it ever does this, we get an
	 * interrupt when it sends us an ack, but by the time we process it,
	 * that flag in the SW2 status register has been cleared by the CPU
	 * firmware.  We'll prevent that not so useful condition from happening
	 * by clearing the CPU's interrupt enables for Ack IRQ's we want to
	 * process.
	 */
	cx18_sw2_irq_disable_cpu(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);

	/* Try a benign command to see if the CPU is alive and well */
	sz = cx18_vapi_result(cx, api_args, CX18_CPU_DEBUG_PEEK32, 1, 0);
	if (sz < 0)
		return sz;

	/* initialize GPIO */
	cx18_write_reg_expect(cx, 0x14001400, 0xc78110, 0x00001400, 0x14001400);
	return 0;
}
static int load_apu_fw_direct(const char *fn, u8 __iomem *dst, struct cx18 *cx,
				u32 *entry_addr)
{
	const struct firmware *fw = NULL;
	int i, j;
	unsigned size;
	const u32 *src;
	struct cx18_apu_rom_seghdr seghdr;
	const u8 *vers;
	u32 offset = 0;
	u32 apu_version = 0;
	int sz;

	if (request_firmware(&fw, fn, &cx->pci_dev->dev)) {
		CX18_ERR("unable to open firmware %s\n", fn);
		CX18_ERR("did you put the firmware in the hotplug firmware directory?\n");
		cx18_setup_page(cx, 0);
		return -ENOMEM;
	}

	*entry_addr = 0;
	src = (const u32 *)fw->data;
	vers = fw->data + sizeof(seghdr);
	sz = fw->size;

	apu_version = (vers[0] << 24) | (vers[4] << 16) | vers[32];
	while (offset + sizeof(seghdr) < fw->size) {
		/* TODO: byteswapping */
		memcpy(&seghdr, src + offset / 4, sizeof(seghdr));
		offset += sizeof(seghdr);
		if (seghdr.sync1 != APU_ROM_SYNC1 ||
		    seghdr.sync2 != APU_ROM_SYNC2) {
			offset += seghdr.size;
			continue;
		}
		CX18_DEBUG_INFO("load segment %x-%x\n", seghdr.addr,
				seghdr.addr + seghdr.size - 1);
		if (*entry_addr == 0)
			*entry_addr = seghdr.addr;
		if (offset + seghdr.size > sz)
			break;
		for (i = 0; i < seghdr.size; i += 4096) {
			cx18_setup_page(cx, seghdr.addr + i);
			for (j = i; j < seghdr.size && j < i + 4096; j += 4) {
				/* no need for endianness conversion on the ppc */
				cx18_raw_writel(cx, src[(offset + j) / 4],
						dst + seghdr.addr + j);
				if (cx18_raw_readl(cx, dst + seghdr.addr + j)
				    != src[(offset + j) / 4]) {
					CX18_ERR("Mismatch at offset %x\n",
						 offset + j);
					release_firmware(fw);
					cx18_setup_page(cx, 0);
					return -EIO;
				}
			}
		}
		offset += seghdr.size;
	}
	if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
		CX18_INFO("loaded %s firmware V%08x (%zd bytes)\n",
				fn, apu_version, fw->size);
	size = fw->size;
	release_firmware(fw);
	cx18_setup_page(cx, 0);
	return size;
}
Ejemplo n.º 20
0
static int __devinit cx18_probe(struct pci_dev *pci_dev,
				const struct pci_device_id *pci_id)
{
	int retval = 0;
	int i;
	u32 devtype;
	struct cx18 *cx;

	/* FIXME - module parameter arrays constrain max instances */
	i = atomic_inc_return(&cx18_instance) - 1;
	if (i >= CX18_MAX_CARDS) {
		printk(KERN_ERR "cx18: cannot manage card %d, driver has a "
		       "limit of 0 - %d\n", i, CX18_MAX_CARDS - 1);
		return -ENOMEM;
	}

	cx = kzalloc(sizeof(struct cx18), GFP_ATOMIC);
	if (cx == NULL) {
		printk(KERN_ERR "cx18: cannot manage card %d, out of memory\n",
		       i);
		return -ENOMEM;
	}
	cx->pci_dev = pci_dev;
	cx->instance = i;

	retval = v4l2_device_register(&pci_dev->dev, &cx->v4l2_dev);
	if (retval) {
		printk(KERN_ERR "cx18: v4l2_device_register of card %d failed"
		       "\n", cx->instance);
		kfree(cx);
		return retval;
	}
	snprintf(cx->v4l2_dev.name, sizeof(cx->v4l2_dev.name), "cx18-%d",
		 cx->instance);
	CX18_INFO("Initializing card %d\n", cx->instance);

	cx18_process_options(cx);
	if (cx->options.cardtype == -1) {
		retval = -ENODEV;
		goto err;
	}

	retval = cx18_init_struct1(cx);
	if (retval)
		goto err;

	CX18_DEBUG_INFO("base addr: 0x%08x\n", cx->base_addr);

	/* PCI Device Setup */
	retval = cx18_setup_pci(cx, pci_dev, pci_id);
	if (retval != 0)
		goto free_workqueues;

	/* map io memory */
	CX18_DEBUG_INFO("attempting ioremap at 0x%08x len 0x%08x\n",
		   cx->base_addr + CX18_MEM_OFFSET, CX18_MEM_SIZE);
	cx->enc_mem = ioremap_nocache(cx->base_addr + CX18_MEM_OFFSET,
				       CX18_MEM_SIZE);
	if (!cx->enc_mem) {
		CX18_ERR("ioremap failed. Can't get a window into CX23418 "
			 "memory and register space\n");
		CX18_ERR("Each capture card with a CX23418 needs 64 MB of "
			 "vmalloc address space for the window\n");
		CX18_ERR("Check the output of 'grep Vmalloc /proc/meminfo'\n");
		CX18_ERR("Use the vmalloc= kernel command line option to set "
			 "VmallocTotal to a larger value\n");
		retval = -ENOMEM;
		goto free_mem;
	}
	cx->reg_mem = cx->enc_mem + CX18_REG_OFFSET;
	devtype = cx18_read_reg(cx, 0xC72028);
	switch (devtype & 0xff000000) {
	case 0xff000000:
		CX18_INFO("cx23418 revision %08x (A)\n", devtype);
		break;
	case 0x01000000:
		CX18_INFO("cx23418 revision %08x (B)\n", devtype);
		break;
	default:
		CX18_INFO("cx23418 revision %08x (Unknown)\n", devtype);
		break;
	}

	cx18_init_power(cx, 1);
	cx18_init_memory(cx);

	cx->scb = (struct cx18_scb __iomem *)(cx->enc_mem + SCB_OFFSET);
	cx18_init_scb(cx);

	cx18_gpio_init(cx);

	/* Initialize integrated A/V decoder early to set PLLs, just in case */
	retval = cx18_av_probe(cx);
	if (retval) {
		CX18_ERR("Could not register A/V decoder subdevice\n");
		goto free_map;
	}

	/* Initialize GPIO Reset Controller to do chip resets during i2c init */
	if (cx->card->hw_all & CX18_HW_GPIO_RESET_CTRL) {
		if (cx18_gpio_register(cx, CX18_HW_GPIO_RESET_CTRL) != 0)
			CX18_WARN("Could not register GPIO reset controller"
				  "subdevice; proceeding anyway.\n");
		else
			cx->hw_flags |= CX18_HW_GPIO_RESET_CTRL;
	}

	/* active i2c  */
	CX18_DEBUG_INFO("activating i2c...\n");
	retval = init_cx18_i2c(cx);
	if (retval) {
		CX18_ERR("Could not initialize i2c\n");
		goto free_map;
	}

	if (cx->card->hw_all & CX18_HW_TVEEPROM) {
		/* Based on the model number the cardtype may be changed.
		   The PCI IDs are not always reliable. */
		const struct cx18_card *orig_card = cx->card;
		cx18_process_eeprom(cx);

		if (cx->card != orig_card) {
			/* Changed the cardtype; re-reset the I2C chips */
			cx18_gpio_init(cx);
			cx18_call_hw(cx, CX18_HW_GPIO_RESET_CTRL,
					core, reset, (u32) CX18_GPIO_RESET_I2C);
		}
	}
	if (cx->card->comment)
		CX18_INFO("%s", cx->card->comment);
	if (cx->card->v4l2_capabilities == 0) {
		retval = -ENODEV;
		goto free_i2c;
	}
	cx18_init_memory(cx);
	cx18_init_scb(cx);

	/* Register IRQ */
	retval = request_irq(cx->pci_dev->irq, cx18_irq_handler,
			     IRQF_SHARED | IRQF_DISABLED,
			     cx->v4l2_dev.name, (void *)cx);
	if (retval) {
		CX18_ERR("Failed to register irq %d\n", retval);
		goto free_i2c;
	}

	if (cx->std == 0)
		cx->std = V4L2_STD_NTSC_M;

	if (cx->options.tuner == -1) {
		for (i = 0; i < CX18_CARD_MAX_TUNERS; i++) {
			if ((cx->std & cx->card->tuners[i].std) == 0)
				continue;
			cx->options.tuner = cx->card->tuners[i].tuner;
			break;
		}
	}
	/* if no tuner was found, then pick the first tuner in the card list */
	if (cx->options.tuner == -1 && cx->card->tuners[0].std) {
		cx->std = cx->card->tuners[0].std;
		if (cx->std & V4L2_STD_PAL)
			cx->std = V4L2_STD_PAL_BG | V4L2_STD_PAL_H;
		else if (cx->std & V4L2_STD_NTSC)
			cx->std = V4L2_STD_NTSC_M;
		else if (cx->std & V4L2_STD_SECAM)
			cx->std = V4L2_STD_SECAM_L;
		cx->options.tuner = cx->card->tuners[0].tuner;
	}
	if (cx->options.radio == -1)
		cx->options.radio = (cx->card->radio_input.audio_type != 0);

	/* The card is now fully identified, continue with card-specific
	   initialization. */
	cx18_init_struct2(cx);

	cx18_init_subdevs(cx);

	if (cx->std & V4L2_STD_525_60)
		cx->is_60hz = 1;
	else
		cx->is_50hz = 1;

	cx2341x_handler_set_50hz(&cx->cxhdl, !cx->is_60hz);

	if (cx->options.radio > 0)
		cx->v4l2_cap |= V4L2_CAP_RADIO;

	if (cx->options.tuner > -1) {
		struct tuner_setup setup;

		setup.addr = ADDR_UNSET;
		setup.type = cx->options.tuner;
		setup.mode_mask = T_ANALOG_TV;  /* matches TV tuners */
		setup.tuner_callback = (setup.type == TUNER_XC2028) ?
			cx18_reset_tuner_gpio : NULL;
		cx18_call_all(cx, tuner, s_type_addr, &setup);
		if (setup.type == TUNER_XC2028) {
			static struct xc2028_ctrl ctrl = {
				.fname = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
			};
			struct v4l2_priv_tun_config cfg = {
				.tuner = cx->options.tuner,
				.priv = &ctrl,
			};
			cx18_call_all(cx, tuner, s_config, &cfg);
		}
	}

	/* The tuner is fixed to the standard. The other inputs (e.g. S-Video)
	   are not. */
	cx->tuner_std = cx->std;
	if (cx->std == V4L2_STD_ALL)
		cx->std = V4L2_STD_NTSC_M;

	retval = cx18_streams_setup(cx);
	if (retval) {
		CX18_ERR("Error %d setting up streams\n", retval);
		goto free_irq;
	}
	retval = cx18_streams_register(cx);
	if (retval) {
		CX18_ERR("Error %d registering devices\n", retval);
		goto free_streams;
	}

	CX18_INFO("Initialized card: %s\n", cx->card_name);

	/* Load cx18 submodules (cx18-alsa) */
	request_modules(cx);
	return 0;

free_streams:
	cx18_streams_cleanup(cx, 1);
free_irq:
	free_irq(cx->pci_dev->irq, (void *)cx);
free_i2c:
	exit_cx18_i2c(cx);
free_map:
	cx18_iounmap(cx);
free_mem:
	release_mem_region(cx->base_addr, CX18_MEM_SIZE);
free_workqueues:
	destroy_workqueue(cx->in_work_queue);
err:
	if (retval == 0)
		retval = -ENODEV;
	CX18_ERR("Error %d on initialization\n", retval);

	v4l2_device_unregister(&cx->v4l2_dev);
	kfree(cx);
	return retval;
}

int cx18_init_on_first_open(struct cx18 *cx)
{
	int video_input;
	int fw_retry_count = 3;
	struct v4l2_frequency vf;
	struct cx18_open_id fh;
	v4l2_std_id std;

	fh.cx = cx;

	if (test_bit(CX18_F_I_FAILED, &cx->i_flags))
		return -ENXIO;

	if (test_and_set_bit(CX18_F_I_INITED, &cx->i_flags))
		return 0;

	while (--fw_retry_count > 0) {
		/* load firmware */
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}
	set_bit(CX18_F_I_LOADED_FW, &cx->i_flags);

	/*
	 * Init the firmware twice to work around a silicon bug
	 * with the digital TS.
	 *
	 * The second firmware load requires us to normalize the APU state,
	 * or the audio for the first analog capture will be badly incorrect.
	 *
	 * I can't seem to call APU_RESETAI and have it succeed without the
	 * APU capturing audio, so we start and stop it here to do the reset
	 */

	/* MPEG Encoding, 224 kbps, MPEG Layer II, 48 ksps */
	cx18_vapi(cx, CX18_APU_START, 2, CX18_APU_ENCODING_METHOD_MPEG|0xb9, 0);
	cx18_vapi(cx, CX18_APU_RESETAI, 0);
	cx18_vapi(cx, CX18_APU_STOP, 1, CX18_APU_ENCODING_METHOD_MPEG);

	fw_retry_count = 3;
	while (--fw_retry_count > 0) {
		/* load firmware */
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}

	/*
	 * The second firmware load requires us to normalize the APU state,
	 * or the audio for the first analog capture will be badly incorrect.
	 *
	 * I can't seem to call APU_RESETAI and have it succeed without the
	 * APU capturing audio, so we start and stop it here to do the reset
	 */

	/* MPEG Encoding, 224 kbps, MPEG Layer II, 48 ksps */
	cx18_vapi(cx, CX18_APU_START, 2, CX18_APU_ENCODING_METHOD_MPEG|0xb9, 0);
	cx18_vapi(cx, CX18_APU_RESETAI, 0);
	cx18_vapi(cx, CX18_APU_STOP, 1, CX18_APU_ENCODING_METHOD_MPEG);

	/* Init the A/V decoder, if it hasn't been already */
	v4l2_subdev_call(cx->sd_av, core, load_fw);

	vf.tuner = 0;
	vf.type = V4L2_TUNER_ANALOG_TV;
	vf.frequency = 6400; /* the tuner 'baseline' frequency */

	/* Set initial frequency. For PAL/SECAM broadcasts no
	   'default' channel exists AFAIK. */
	if (cx->std == V4L2_STD_NTSC_M_JP)
		vf.frequency = 1460;	/* ch. 1 91250*16/1000 */
	else if (cx->std & V4L2_STD_NTSC_M)
		vf.frequency = 1076;	/* ch. 4 67250*16/1000 */

	video_input = cx->active_input;
	cx->active_input++;	/* Force update of input */
	cx18_s_input(NULL, &fh, video_input);

	/* Let the VIDIOC_S_STD ioctl do all the work, keeps the code
	   in one place. */
	cx->std++;		/* Force full standard initialization */
	std = (cx->tuner_std == V4L2_STD_ALL) ? V4L2_STD_NTSC_M : cx->tuner_std;
	cx18_s_std(NULL, &fh, &std);
	cx18_s_frequency(NULL, &fh, &vf);
	return 0;
}

static void cx18_cancel_in_work_orders(struct cx18 *cx)
{
	int i;
	for (i = 0; i < CX18_MAX_IN_WORK_ORDERS; i++)
		cancel_work_sync(&cx->in_work_order[i].work);
}
Ejemplo n.º 21
0
static int cx18_api_call(struct cx18 *cx, u32 cmd, int args, u32 data[])
{
	const struct cx18_api_info *info = find_api_info(cmd);
	u32 state, irq, req, ack, err;
	struct cx18_mailbox __iomem *mb;
	u32 __iomem *xpu_state;
	wait_queue_head_t *waitq;
	struct mutex *mb_lock;
	long int timeout, ret;
	int i;
	char argstr[MAX_MB_ARGUMENTS*11+1];

	if (info == NULL) {
		CX18_WARN("unknown cmd %x\n", cmd);
		return -EINVAL;
	}

	if (cx18_debug & CX18_DBGFLG_API) { /* only call u32arr2hex if needed */
		if (cmd == CX18_CPU_DE_SET_MDL) {
			if (cx18_debug & CX18_DBGFLG_HIGHVOL)
				CX18_DEBUG_HI_API("%s\tcmd %#010x args%s\n",
						info->name, cmd,
						u32arr2hex(data, args, argstr));
		} else
			CX18_DEBUG_API("%s\tcmd %#010x args%s\n",
				       info->name, cmd,
				       u32arr2hex(data, args, argstr));
	}

	switch (info->rpu) {
	case APU:
		waitq = &cx->mb_apu_waitq;
		mb_lock = &cx->epu2apu_mb_lock;
		irq = IRQ_EPU_TO_APU;
		mb = &cx->scb->epu2apu_mb;
		xpu_state = &cx->scb->apu_state;
		break;
	case CPU:
		waitq = &cx->mb_cpu_waitq;
		mb_lock = &cx->epu2cpu_mb_lock;
		irq = IRQ_EPU_TO_CPU;
		mb = &cx->scb->epu2cpu_mb;
		xpu_state = &cx->scb->cpu_state;
		break;
	default:
		CX18_WARN("Unknown RPU (%d) for API call\n", info->rpu);
		return -EINVAL;
	}

	mutex_lock(mb_lock);
	/*
	 * Wait for an in-use mailbox to complete
	 *
	 * If the XPU is responding with Ack's, the mailbox shouldn't be in
	 * a busy state, since we serialize access to it on our end.
	 *
	 * If the wait for ack after sending a previous command was interrupted
	 * by a signal, we may get here and find a busy mailbox.  After waiting,
	 * mark it "not busy" from our end, if the XPU hasn't ack'ed it still.
	 */
	state = cx18_readl(cx, xpu_state);
	req = cx18_readl(cx, &mb->request);
	timeout = msecs_to_jiffies(10);
	ret = wait_event_timeout(*waitq,
				 (ack = cx18_readl(cx, &mb->ack)) == req,
				 timeout);
	if (req != ack) {
		/* waited long enough, make the mbox "not busy" from our end */
		cx18_writel(cx, req, &mb->ack);
		CX18_ERR("mbox was found stuck busy when setting up for %s; "
			 "clearing busy and trying to proceed\n", info->name);
	} else if (ret != timeout)
		CX18_DEBUG_API("waited %u msecs for busy mbox to be acked\n",
			       jiffies_to_msecs(timeout-ret));

	/* Build the outgoing mailbox */
	req = ((req & 0xfffffffe) == 0xfffffffe) ? 1 : req + 1;

	cx18_writel(cx, cmd, &mb->cmd);
	for (i = 0; i < args; i++)
		cx18_writel(cx, data[i], &mb->args[i]);
	cx18_writel(cx, 0, &mb->error);
	cx18_writel(cx, req, &mb->request);
	cx18_writel(cx, req - 1, &mb->ack); /* ensure ack & req are distinct */

	/*
	 * Notify the XPU and wait for it to send an Ack back
	 */
	timeout = msecs_to_jiffies((info->flags & API_FAST) ? 10 : 20);

	CX18_DEBUG_HI_IRQ("sending interrupt SW1: %x to send %s\n",
			  irq, info->name);
	cx18_write_reg_expect(cx, irq, SW1_INT_SET, irq, irq);

	ret = wait_event_timeout(
		       *waitq,
		       cx18_readl(cx, &mb->ack) == cx18_readl(cx, &mb->request),
		       timeout);

	if (ret == 0) {
		/* Timed out */
		mutex_unlock(mb_lock);
		CX18_DEBUG_WARN("sending %s timed out waiting %d msecs for RPU "
				"acknowledgement\n",
				info->name, jiffies_to_msecs(timeout));
		return -EINVAL;
	}

	if (ret != timeout)
		CX18_DEBUG_HI_API("waited %u msecs for %s to be acked\n",
				  jiffies_to_msecs(timeout-ret), info->name);

	/* Collect data returned by the XPU */
	for (i = 0; i < MAX_MB_ARGUMENTS; i++)
		data[i] = cx18_readl(cx, &mb->args[i]);
	err = cx18_readl(cx, &mb->error);
	mutex_unlock(mb_lock);

	/*
	 * Wait for XPU to perform extra actions for the caller in some cases.
	 * e.g. CX18_CPU_DE_RELEASE_MDL will cause the CPU to send all buffers
	 * back in a burst shortly thereafter
	 */
	if (info->flags & API_SLOW)
		cx18_msleep_timeout(300, 0);

	if (err)
		CX18_DEBUG_API("mailbox error %08x for command %s\n", err,
				info->name);
	return err ? -EIO : 0;
}
Ejemplo n.º 22
0
static int cx18_prep_dev(struct cx18 *cx, int type)
{
	struct cx18_stream *s = &cx->streams[type];
	u32 cap = cx->v4l2_cap;
	int num_offset = cx18_stream_info[type].num_offset;
	int num = cx->instance + cx18_first_minor + num_offset;

	/*
	 * These five fields are always initialized.
	 * For analog capture related streams, if video_dev == NULL then the
	 * stream is not in use.
	 * For the TS stream, if dvb == NULL then the stream is not in use.
	 * In those cases no other fields but these four can be used.
	 */
	s->video_dev = NULL;
	s->dvb = NULL;
	s->cx = cx;
	s->type = type;
	s->name = cx18_stream_info[type].name;

	/* Check whether the radio is supported */
	if (type == CX18_ENC_STREAM_TYPE_RAD && !(cap & V4L2_CAP_RADIO))
		return 0;

	/* Check whether VBI is supported */
	if (type == CX18_ENC_STREAM_TYPE_VBI &&
	    !(cap & (V4L2_CAP_VBI_CAPTURE | V4L2_CAP_SLICED_VBI_CAPTURE)))
		return 0;

	/* User explicitly selected 0 buffers for these streams, so don't
	   create them. */
	if (cx18_stream_info[type].dma != PCI_DMA_NONE &&
	    cx->stream_buffers[type] == 0) {
		CX18_INFO("Disabled %s device\n", cx18_stream_info[type].name);
		return 0;
	}

	cx18_stream_init(cx, type);

	/* Allocate the cx18_dvb struct only for the TS on cards with DTV */
	if (type == CX18_ENC_STREAM_TYPE_TS) {
		if (cx->card->hw_all & CX18_HW_DVB) {
			s->dvb = kzalloc(sizeof(struct cx18_dvb), GFP_KERNEL);
			if (s->dvb == NULL) {
				CX18_ERR("Couldn't allocate cx18_dvb structure"
					 " for %s\n", s->name);
				return -ENOMEM;
			}
		} else {
			/* Don't need buffers for the TS, if there is no DVB */
			s->buffers = 0;
		}
	}

	if (num_offset == -1)
		return 0;

	/* allocate and initialize the v4l2 video device structure */
	s->video_dev = video_device_alloc();
	if (s->video_dev == NULL) {
		CX18_ERR("Couldn't allocate v4l2 video_device for %s\n",
				s->name);
		return -ENOMEM;
	}

	snprintf(s->video_dev->name, sizeof(s->video_dev->name), "%s %s",
		 cx->v4l2_dev.name, s->name);

	s->video_dev->num = num;
	s->video_dev->v4l2_dev = &cx->v4l2_dev;
	s->video_dev->fops = &cx18_v4l2_enc_fops;
	s->video_dev->release = video_device_release;
	s->video_dev->tvnorms = V4L2_STD_ALL;
	s->video_dev->lock = &cx->serialize_lock;
	set_bit(V4L2_FL_USE_FH_PRIO, &s->video_dev->flags);
	cx18_set_funcs(s->video_dev);
	return 0;
}
Ejemplo n.º 23
0
static int cx18_reg_dev(struct cx18 *cx, int type)
{
	struct cx18_stream *s = &cx->streams[type];
	int vfl_type = cx18_stream_info[type].vfl_type;
	int num, ret;

	/* TODO: Shouldn't this be a VFL_TYPE_TRANSPORT or something?
	 * We need a VFL_TYPE_TS defined.
	 */
	if (strcmp("TS", s->name) == 0) {
		/* just return if no DVB is supported */
		if ((cx->card->hw_all & CX18_HW_DVB) == 0)
			return 0;
		ret = cx18_dvb_register(s);
		if (ret < 0) {
			CX18_ERR("DVB failed to register\n");
			return ret;
		}
	}

	if (s->video_dev == NULL)
		return 0;

	num = s->video_dev->num;
	/* card number + user defined offset + device offset */
	if (type != CX18_ENC_STREAM_TYPE_MPG) {
		struct cx18_stream *s_mpg = &cx->streams[CX18_ENC_STREAM_TYPE_MPG];

		if (s_mpg->video_dev)
			num = s_mpg->video_dev->num
			    + cx18_stream_info[type].num_offset;
	}
	video_set_drvdata(s->video_dev, s);

	/* Register device. First try the desired minor, then any free one. */
	ret = video_register_device_no_warn(s->video_dev, vfl_type, num);
	if (ret < 0) {
		CX18_ERR("Couldn't register v4l2 device for %s (device node number %d)\n",
			s->name, num);
		video_device_release(s->video_dev);
		s->video_dev = NULL;
		return ret;
	}
	num = s->video_dev->num;

	switch (vfl_type) {
	case VFL_TYPE_GRABBER:
		CX18_INFO("Registered device video%d for %s "
			  "(%d x %d.%02d kB)\n",
			  num, s->name, cx->stream_buffers[type],
			  cx->stream_buf_size[type] / 1024,
			  (cx->stream_buf_size[type] * 100 / 1024) % 100);
		break;

	case VFL_TYPE_RADIO:
		CX18_INFO("Registered device radio%d for %s\n",
			num, s->name);
		break;

	case VFL_TYPE_VBI:
		if (cx->stream_buffers[type])
			CX18_INFO("Registered device vbi%d for %s "
				  "(%d x %d bytes)\n",
				  num, s->name, cx->stream_buffers[type],
				  cx->stream_buf_size[type]);
		else
			CX18_INFO("Registered device vbi%d for %s\n",
				num, s->name);
		break;
	}

	return 0;
}
Ejemplo n.º 24
0
/* init + register i2c algo-bit adapter */
int init_cx18_i2c(struct cx18 *cx)
{
	int i;
	CX18_DEBUG_I2C("i2c init\n");

	/* Sanity checks for the I2C hardware arrays. They must be the
	 * same size and GPIO/CX23418 must be the last entries.
	 */
	if (ARRAY_SIZE(hw_driverids) != ARRAY_SIZE(hw_addrs) ||
	    ARRAY_SIZE(hw_devicenames) != ARRAY_SIZE(hw_addrs) ||
	    CX18_HW_GPIO != (1 << (ARRAY_SIZE(hw_addrs) - 2)) ||
	    CX18_HW_CX23418 != (1 << (ARRAY_SIZE(hw_addrs) - 1)) ||
	    hw_driverids[ARRAY_SIZE(hw_addrs) - 1]) {
		CX18_ERR("Mismatched I2C hardware arrays\n");
		return -ENODEV;
	}

	for (i = 0; i < 2; i++) {
		memcpy(&cx->i2c_adap[i], &cx18_i2c_adap_template,
			sizeof(struct i2c_adapter));
		memcpy(&cx->i2c_algo[i], &cx18_i2c_algo_template,
			sizeof(struct i2c_algo_bit_data));
		cx->i2c_algo_cb_data[i].cx = cx;
		cx->i2c_algo_cb_data[i].bus_index = i;
		cx->i2c_algo[i].data = &cx->i2c_algo_cb_data[i];
		cx->i2c_adap[i].algo_data = &cx->i2c_algo[i];

		sprintf(cx->i2c_adap[i].name + strlen(cx->i2c_adap[i].name),
				" #%d-%d", cx->num, i);
		i2c_set_adapdata(&cx->i2c_adap[i], cx);

		memcpy(&cx->i2c_client[i], &cx18_i2c_client_template,
			sizeof(struct i2c_client));
		sprintf(cx->i2c_client[i].name +
				strlen(cx->i2c_client[i].name), "%d", i);
		cx->i2c_client[i].adapter = &cx->i2c_adap[i];
		cx->i2c_adap[i].dev.parent = &cx->dev->dev;
	}

	if (cx18_read_reg(cx, CX18_REG_I2C_2_WR) != 0x0003c02f) {
		/* Reset/Unreset I2C hardware block */
		/* Clock select 220MHz */
		cx18_write_reg_expect(cx, 0x10000000, 0xc71004,
					  0x00000000, 0x10001000);
		/* Clock Enable */
		cx18_write_reg_expect(cx, 0x10001000, 0xc71024,
					  0x00001000, 0x10001000);
	}
	/* courtesy of Steven Toth <[email protected]> */
	cx18_write_reg_expect(cx, 0x00c00000, 0xc7001c, 0x00000000, 0x00c000c0);
	mdelay(10);
	cx18_write_reg_expect(cx, 0x00c000c0, 0xc7001c, 0x000000c0, 0x00c000c0);
	mdelay(10);
	cx18_write_reg_expect(cx, 0x00c00000, 0xc7001c, 0x00000000, 0x00c000c0);
	mdelay(10);

	/* Set to edge-triggered intrs. */
	cx18_write_reg(cx, 0x00c00000, 0xc730c8);
	/* Clear any stale intrs */
	cx18_write_reg_expect(cx, HW2_I2C1_INT|HW2_I2C2_INT, HW2_INT_CLR_STATUS,
		       ~(HW2_I2C1_INT|HW2_I2C2_INT), HW2_I2C1_INT|HW2_I2C2_INT);

	/* Hw I2C1 Clock Freq ~100kHz */
	cx18_write_reg(cx, 0x00021c0f & ~4, CX18_REG_I2C_1_WR);
	cx18_setscl(&cx->i2c_algo_cb_data[0], 1);
	cx18_setsda(&cx->i2c_algo_cb_data[0], 1);

	/* Hw I2C2 Clock Freq ~100kHz */
	cx18_write_reg(cx, 0x00021c0f & ~4, CX18_REG_I2C_2_WR);
	cx18_setscl(&cx->i2c_algo_cb_data[1], 1);
	cx18_setsda(&cx->i2c_algo_cb_data[1], 1);

	cx18_reset_i2c_slaves_gpio(cx);

	return i2c_bit_add_bus(&cx->i2c_adap[0]) ||
		i2c_bit_add_bus(&cx->i2c_adap[1]);
}
Ejemplo n.º 25
0
static int __devinit cx18_probe(struct pci_dev *dev,
				const struct pci_device_id *pci_id)
{
	int retval = 0;
	int vbi_buf_size;
	u32 devtype;
	struct cx18 *cx;

	spin_lock(&cx18_cards_lock);

	/* Make sure we've got a place for this card */
	if (cx18_cards_active == CX18_MAX_CARDS) {
		printk(KERN_ERR "cx18:  Maximum number of cards detected (%d).\n",
			      cx18_cards_active);
		spin_unlock(&cx18_cards_lock);
		return -ENOMEM;
	}

	cx = kzalloc(sizeof(struct cx18), GFP_ATOMIC);
	if (!cx) {
		spin_unlock(&cx18_cards_lock);
		return -ENOMEM;
	}
	cx18_cards[cx18_cards_active] = cx;
	cx->dev = dev;
	cx->num = cx18_cards_active++;
	snprintf(cx->name, sizeof(cx->name), "cx18-%d", cx->num);
	CX18_INFO("Initializing card #%d\n", cx->num);

	spin_unlock(&cx18_cards_lock);

	cx18_process_options(cx);
	if (cx->options.cardtype == -1) {
		retval = -ENODEV;
		goto err;
	}
	if (cx18_init_struct1(cx)) {
		retval = -ENOMEM;
		goto err;
	}

	CX18_DEBUG_INFO("base addr: 0x%08x\n", cx->base_addr);

	/* PCI Device Setup */
	retval = cx18_setup_pci(cx, dev, pci_id);
	if (retval != 0) {
		if (retval == -EIO)
			goto free_workqueue;
		else if (retval == -ENXIO)
			goto free_mem;
	}
	/* save cx in the pci struct for later use */
	pci_set_drvdata(dev, cx);

	/* map io memory */
	CX18_DEBUG_INFO("attempting ioremap at 0x%08x len 0x%08x\n",
		   cx->base_addr + CX18_MEM_OFFSET, CX18_MEM_SIZE);
	cx->enc_mem = ioremap_nocache(cx->base_addr + CX18_MEM_OFFSET,
				       CX18_MEM_SIZE);
	if (!cx->enc_mem) {
		CX18_ERR("ioremap failed, perhaps increasing __VMALLOC_RESERVE in page.h\n");
		CX18_ERR("or disabling CONFIG_HIGHMEM4G into the kernel would help\n");
		retval = -ENOMEM;
		goto free_mem;
	}
	cx->reg_mem = cx->enc_mem + CX18_REG_OFFSET;
	devtype = read_reg(0xC72028);
	switch (devtype & 0xff000000) {
	case 0xff000000:
		CX18_INFO("cx23418 revision %08x (A)\n", devtype);
		break;
	case 0x01000000:
		CX18_INFO("cx23418 revision %08x (B)\n", devtype);
		break;
	default:
		CX18_INFO("cx23418 revision %08x (Unknown)\n", devtype);
		break;
	}

	cx18_init_power(cx, 1);
	cx18_init_memory(cx);

	cx->scb = (struct cx18_scb __iomem *)(cx->enc_mem + SCB_OFFSET);
	cx18_init_scb(cx);

	cx18_gpio_init(cx);

	/* active i2c  */
	CX18_DEBUG_INFO("activating i2c...\n");
	if (init_cx18_i2c(cx)) {
		CX18_ERR("Could not initialize i2c\n");
		goto free_map;
	}

	CX18_DEBUG_INFO("Active card count: %d.\n", cx18_cards_active);

	if (cx->card->hw_all & CX18_HW_TVEEPROM) {
		/* Based on the model number the cardtype may be changed.
		   The PCI IDs are not always reliable. */
		cx18_process_eeprom(cx);
	}
	if (cx->card->comment)
		CX18_INFO("%s", cx->card->comment);
	if (cx->card->v4l2_capabilities == 0) {
		retval = -ENODEV;
		goto free_i2c;
	}
	cx18_init_memory(cx);

	/* Register IRQ */
	retval = request_irq(cx->dev->irq, cx18_irq_handler,
			     IRQF_SHARED | IRQF_DISABLED, cx->name, (void *)cx);
	if (retval) {
		CX18_ERR("Failed to register irq %d\n", retval);
		goto free_i2c;
	}

	if (cx->std == 0)
		cx->std = V4L2_STD_NTSC_M;

	if (cx->options.tuner == -1) {
		int i;

		for (i = 0; i < CX18_CARD_MAX_TUNERS; i++) {
			if ((cx->std & cx->card->tuners[i].std) == 0)
				continue;
			cx->options.tuner = cx->card->tuners[i].tuner;
			break;
		}
	}
	/* if no tuner was found, then pick the first tuner in the card list */
	if (cx->options.tuner == -1 && cx->card->tuners[0].std) {
		cx->std = cx->card->tuners[0].std;
		if (cx->std & V4L2_STD_PAL)
			cx->std = V4L2_STD_PAL_BG | V4L2_STD_PAL_H;
		else if (cx->std & V4L2_STD_NTSC)
			cx->std = V4L2_STD_NTSC_M;
		else if (cx->std & V4L2_STD_SECAM)
			cx->std = V4L2_STD_SECAM_L;
		cx->options.tuner = cx->card->tuners[0].tuner;
	}
	if (cx->options.radio == -1)
		cx->options.radio = (cx->card->radio_input.audio_type != 0);

	/* The card is now fully identified, continue with card-specific
	   initialization. */
	cx18_init_struct2(cx);

	cx18_load_and_init_modules(cx);

	if (cx->std & V4L2_STD_525_60) {
		cx->is_60hz = 1;
		cx->is_out_60hz = 1;
	} else {
		cx->is_50hz = 1;
		cx->is_out_50hz = 1;
	}
	cx->params.video_gop_size = cx->is_60hz ? 15 : 12;

	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_MPG] = 0x08000;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_TS] = 0x08000;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_PCM] = 0x01200;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_YUV] = 0x20000;
	vbi_buf_size = cx->vbi.raw_size * (cx->is_60hz ? 24 : 36) / 2;
	cx->stream_buf_size[CX18_ENC_STREAM_TYPE_VBI] = vbi_buf_size;

	if (cx->options.radio > 0)
		cx->v4l2_cap |= V4L2_CAP_RADIO;

	if (cx->options.tuner > -1) {
		struct tuner_setup setup;

		setup.addr = ADDR_UNSET;
		setup.type = cx->options.tuner;
		setup.mode_mask = T_ANALOG_TV;  /* matches TV tuners */
		setup.tuner_callback = (setup.type == TUNER_XC2028) ?
			cx18_reset_tuner_gpio : NULL;
		cx18_call_i2c_clients(cx, TUNER_SET_TYPE_ADDR, &setup);
		if (setup.type == TUNER_XC2028) {
			static struct xc2028_ctrl ctrl = {
				.fname = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
			};
			struct v4l2_priv_tun_config cfg = {
				.tuner = cx->options.tuner,
				.priv = &ctrl,
			};
			cx18_call_i2c_clients(cx, TUNER_SET_CONFIG, &cfg);
		}
	}

	/* The tuner is fixed to the standard. The other inputs (e.g. S-Video)
	   are not. */
	cx->tuner_std = cx->std;

	retval = cx18_streams_setup(cx);
	if (retval) {
		CX18_ERR("Error %d setting up streams\n", retval);
		goto free_irq;
	}
	retval = cx18_streams_register(cx);
	if (retval) {
		CX18_ERR("Error %d registering devices\n", retval);
		goto free_streams;
	}

	CX18_INFO("Initialized card #%d: %s\n", cx->num, cx->card_name);

	return 0;

free_streams:
	cx18_streams_cleanup(cx, 1);
free_irq:
	free_irq(cx->dev->irq, (void *)cx);
free_i2c:
	exit_cx18_i2c(cx);
free_map:
	cx18_iounmap(cx);
free_mem:
	release_mem_region(cx->base_addr, CX18_MEM_SIZE);
free_workqueue:
err:
	if (retval == 0)
		retval = -ENODEV;
	CX18_ERR("Error %d on initialization\n", retval);

	kfree(cx18_cards[cx18_cards_active]);
	cx18_cards[cx18_cards_active] = NULL;
	return retval;
}

int cx18_init_on_first_open(struct cx18 *cx)
{
	int video_input;
	int fw_retry_count = 3;
	struct v4l2_frequency vf;
	struct cx18_open_id fh;

	fh.cx = cx;

	if (test_bit(CX18_F_I_FAILED, &cx->i_flags))
		return -ENXIO;

	if (test_and_set_bit(CX18_F_I_INITED, &cx->i_flags))
		return 0;

	while (--fw_retry_count > 0) {
		/* load firmware */
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}
	set_bit(CX18_F_I_LOADED_FW, &cx->i_flags);

	/* Init the firmware twice to work around a silicon bug
	 * transport related. */

	fw_retry_count = 3;
	while (--fw_retry_count > 0) {
		/* load firmware */
		if (cx18_firmware_init(cx) == 0)
			break;
		if (fw_retry_count > 1)
			CX18_WARN("Retry loading firmware\n");
	}

	if (fw_retry_count == 0) {
		set_bit(CX18_F_I_FAILED, &cx->i_flags);
		return -ENXIO;
	}

	vf.tuner = 0;
	vf.type = V4L2_TUNER_ANALOG_TV;
	vf.frequency = 6400; /* the tuner 'baseline' frequency */

	/* Set initial frequency. For PAL/SECAM broadcasts no
	   'default' channel exists AFAIK. */
	if (cx->std == V4L2_STD_NTSC_M_JP)
		vf.frequency = 1460;	/* ch. 1 91250*16/1000 */
	else if (cx->std & V4L2_STD_NTSC_M)
		vf.frequency = 1076;	/* ch. 4 67250*16/1000 */

	video_input = cx->active_input;
	cx->active_input++;	/* Force update of input */
	cx18_s_input(NULL, &fh, video_input);

	/* Let the VIDIOC_S_STD ioctl do all the work, keeps the code
	   in one place. */
	cx->std++;		/* Force full standard initialization */
	cx18_s_std(NULL, &fh, &cx->tuner_std);
	cx18_s_frequency(NULL, &fh, &vf);
	return 0;
}

static void cx18_remove(struct pci_dev *pci_dev)
{
	struct cx18 *cx = pci_get_drvdata(pci_dev);

	CX18_DEBUG_INFO("Removing Card #%d\n", cx->num);

	/* Stop all captures */
	CX18_DEBUG_INFO("Stopping all streams\n");
	if (atomic_read(&cx->tot_capturing) > 0)
		cx18_stop_all_captures(cx);

	/* Interrupts */
	sw1_irq_disable(IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU);
	sw2_irq_disable(IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);

	cx18_halt_firmware(cx);

	cx18_streams_cleanup(cx, 1);

	exit_cx18_i2c(cx);

	free_irq(cx->dev->irq, (void *)cx);

	cx18_iounmap(cx);

	release_mem_region(cx->base_addr, CX18_MEM_SIZE);

	pci_disable_device(cx->dev);

	CX18_INFO("Removed %s, card #%d\n", cx->card_name, cx->num);
}

/* define a pci_driver for card detection */
static struct pci_driver cx18_pci_driver = {
      .name =     "cx18",
      .id_table = cx18_pci_tbl,
      .probe =    cx18_probe,
      .remove =   cx18_remove,
};

static int module_start(void)
{
	printk(KERN_INFO "cx18:  Start initialization, version %s\n", CX18_VERSION);

	memset(cx18_cards, 0, sizeof(cx18_cards));

	/* Validate parameters */
	if (cx18_first_minor < 0 || cx18_first_minor >= CX18_MAX_CARDS) {
		printk(KERN_ERR "cx18:  Exiting, ivtv_first_minor must be between 0 and %d\n",
		     CX18_MAX_CARDS - 1);
		return -1;
	}

	if (cx18_debug < 0 || cx18_debug > 511) {
		cx18_debug = 0;
		printk(KERN_INFO "cx18:   Debug value must be >= 0 and <= 511!\n");
	}

	if (pci_register_driver(&cx18_pci_driver)) {
		printk(KERN_ERR "cx18:   Error detecting PCI card\n");
		return -ENODEV;
	}
	printk(KERN_INFO "cx18:  End initialization\n");
	return 0;
}

static void module_cleanup(void)
{
	int i;

	pci_unregister_driver(&cx18_pci_driver);

	for (i = 0; i < cx18_cards_active; i++) {
		if (cx18_cards[i] == NULL)
			continue;
		kfree(cx18_cards[i]);
	}
}
Ejemplo n.º 26
0
/* Kernel DVB framework calls this when the feed needs to start.
 * The CX18 framework should enable the transport DMA handling
 * and queue processing.
 */
static int cx18_dvb_start_feed(struct dvb_demux_feed *feed)
{
	struct dvb_demux *demux = feed->demux;
	struct cx18_stream *stream = (struct cx18_stream *) demux->priv;
	struct cx18 *cx;
	int ret;
	u32 v;

	if (!stream)
		return -EINVAL;

	cx = stream->cx;
	CX18_DEBUG_INFO("Start feed: pid = 0x%x index = %d\n",
			feed->pid, feed->index);

	mutex_lock(&cx->serialize_lock);
	ret = cx18_init_on_first_open(cx);
	mutex_unlock(&cx->serialize_lock);
	if (ret) {
		CX18_ERR("Failed to initialize firmware starting DVB feed\n");
		return ret;
	}
	ret = -EINVAL;

	switch (cx->card->type) {
	case CX18_CARD_HVR_1600_ESMT:
	case CX18_CARD_HVR_1600_SAMSUNG:
	case CX18_CARD_HVR_1600_S5H1411:
		v = cx18_read_reg(cx, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
		v |= 0x00400000; /* Serial Mode */
		v |= 0x00002000; /* Data Length - Byte */
		v |= 0x00010000; /* Error - Polarity */
		v |= 0x00020000; /* Error - Passthru */
		v |= 0x000c0000; /* Error - Ignore */
		cx18_write_reg(cx, v, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
		break;

	case CX18_CARD_LEADTEK_DVR3100H:
	case CX18_CARD_YUAN_MPC718:
	case CX18_CARD_GOTVIEW_PCI_DVD3:
	default:
		/* Assumption - Parallel transport - Signalling
		 * undefined or default.
		 */
		break;
	}

	if (!demux->dmx.frontend)
		return -EINVAL;

	mutex_lock(&stream->dvb->feedlock);
	if (stream->dvb->feeding++ == 0) {
		CX18_DEBUG_INFO("Starting Transport DMA\n");
		mutex_lock(&cx->serialize_lock);
		set_bit(CX18_F_S_STREAMING, &stream->s_flags);
		ret = cx18_start_v4l2_encode_stream(stream);
		if (ret < 0) {
			CX18_DEBUG_INFO("Failed to start Transport DMA\n");
			stream->dvb->feeding--;
			if (stream->dvb->feeding == 0)
				clear_bit(CX18_F_S_STREAMING, &stream->s_flags);
		}
		mutex_unlock(&cx->serialize_lock);
	} else
		ret = 0;
	mutex_unlock(&stream->dvb->feedlock);

	return ret;
}
Ejemplo n.º 27
0
static int cx18_reg_dev(struct cx18 *cx, int type)
{
	struct cx18_stream *s = &cx->streams[type];
	int vfl_type = cx18_stream_info[type].vfl_type;
	const char *name;
	int num, ret;

	if (type == CX18_ENC_STREAM_TYPE_TS && s->dvb != NULL) {
		ret = cx18_dvb_register(s);
		if (ret < 0) {
			CX18_ERR("DVB failed to register\n");
			return ret;
		}
	}

	if (s->video_dev == NULL)
		return 0;

	num = s->video_dev->num;
	/* card number + user defined offset + device offset */
	if (type != CX18_ENC_STREAM_TYPE_MPG) {
		struct cx18_stream *s_mpg = &cx->streams[CX18_ENC_STREAM_TYPE_MPG];

		if (s_mpg->video_dev)
			num = s_mpg->video_dev->num
			    + cx18_stream_info[type].num_offset;
	}
	video_set_drvdata(s->video_dev, s);

	/* Register device. First try the desired minor, then any free one. */
	ret = video_register_device_no_warn(s->video_dev, vfl_type, num);
	if (ret < 0) {
		CX18_ERR("Couldn't register v4l2 device for %s (device node number %d)\n",
			s->name, num);
		video_device_release(s->video_dev);
		s->video_dev = NULL;
		return ret;
	}

	name = video_device_node_name(s->video_dev);

	switch (vfl_type) {
	case VFL_TYPE_GRABBER:
		CX18_INFO("Registered device %s for %s (%d x %d.%02d kB)\n",
			  name, s->name, cx->stream_buffers[type],
			  cx->stream_buf_size[type] / 1024,
			  (cx->stream_buf_size[type] * 100 / 1024) % 100);
		break;

	case VFL_TYPE_RADIO:
		CX18_INFO("Registered device %s for %s\n", name, s->name);
		break;

	case VFL_TYPE_VBI:
		if (cx->stream_buffers[type])
			CX18_INFO("Registered device %s for %s "
				  "(%d x %d bytes)\n",
				  name, s->name, cx->stream_buffers[type],
				  cx->stream_buf_size[type]);
		else
			CX18_INFO("Registered device %s for %s\n",
				name, s->name);
		break;
	}

	return 0;
}
Ejemplo n.º 28
0
/* All the DVB attach calls go here, this function get's modified
 * for each new card. cx18_dvb_start_feed() will also need changes.
 */
static int dvb_register(struct cx18_stream *stream)
{
	struct cx18_dvb *dvb = stream->dvb;
	struct cx18 *cx = stream->cx;
	int ret = 0;

	switch (cx->card->type) {
	case CX18_CARD_HVR_1600_ESMT:
	case CX18_CARD_HVR_1600_SAMSUNG:
		dvb->fe = dvb_attach(s5h1409_attach,
			&hauppauge_hvr1600_config,
			&cx->i2c_adap[0]);
		if (dvb->fe != NULL) {
			dvb_attach(mxl5005s_attach, dvb->fe,
				&cx->i2c_adap[0],
				&hauppauge_hvr1600_tuner);
			ret = 0;
		}
		break;
	case CX18_CARD_HVR_1600_S5H1411:
		dvb->fe = dvb_attach(s5h1411_attach,
				     &hcw_s5h1411_config,
				     &cx->i2c_adap[0]);
		if (dvb->fe != NULL)
			dvb_attach(tda18271_attach, dvb->fe,
				   0x60, &cx->i2c_adap[0],
				   &hauppauge_tda18271_config);
		break;
	case CX18_CARD_LEADTEK_DVR3100H:
		dvb->fe = dvb_attach(zl10353_attach,
				     &leadtek_dvr3100h_demod,
				     &cx->i2c_adap[1]);
		if (dvb->fe != NULL) {
			struct dvb_frontend *fe;
			struct xc2028_config cfg = {
				.i2c_adap = &cx->i2c_adap[1],
				.i2c_addr = 0xc2 >> 1,
				.ctrl = NULL,
			};
			static struct xc2028_ctrl ctrl = {
				.fname   = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
				.demod   = XC3028_FE_ZARLINK456,
				.type    = XC2028_AUTO,
			};

			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
				fe->ops.tuner_ops.set_config(fe, &ctrl);
		}
		break;
	case CX18_CARD_YUAN_MPC718:
		/*
		 * TODO
		 * Apparently, these cards also could instead have a
		 * DiBcom demod supported by one of the db7000 drivers
		 */
		dvb->fe = dvb_attach(mt352_attach,
				     &yuan_mpc718_mt352_demod,
				     &cx->i2c_adap[1]);
		if (dvb->fe == NULL)
			dvb->fe = dvb_attach(zl10353_attach,
					     &yuan_mpc718_zl10353_demod,
					     &cx->i2c_adap[1]);
		if (dvb->fe != NULL) {
			struct dvb_frontend *fe;
			struct xc2028_config cfg = {
				.i2c_adap = &cx->i2c_adap[1],
				.i2c_addr = 0xc2 >> 1,
				.ctrl = NULL,
			};
			static struct xc2028_ctrl ctrl = {
				.fname   = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
				.demod   = XC3028_FE_ZARLINK456,
				.type    = XC2028_AUTO,
			};

			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
				fe->ops.tuner_ops.set_config(fe, &ctrl);
		}
		break;
	case CX18_CARD_GOTVIEW_PCI_DVD3:
			dvb->fe = dvb_attach(zl10353_attach,
					     &gotview_dvd3_zl10353_demod,
					     &cx->i2c_adap[1]);
		if (dvb->fe != NULL) {
			struct dvb_frontend *fe;
			struct xc2028_config cfg = {
				.i2c_adap = &cx->i2c_adap[1],
				.i2c_addr = 0xc2 >> 1,
				.ctrl = NULL,
			};
			static struct xc2028_ctrl ctrl = {
				.fname   = XC2028_DEFAULT_FIRMWARE,
				.max_len = 64,
				.demod   = XC3028_FE_ZARLINK456,
				.type    = XC2028_AUTO,
			};

			fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
			if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
				fe->ops.tuner_ops.set_config(fe, &ctrl);
		}
		break;
	default:
		/* No Digital Tv Support */
		break;
	}

	if (dvb->fe == NULL) {
		CX18_ERR("frontend initialization failed\n");
		return -1;
	}

	dvb->fe->callback = cx18_reset_tuner_gpio;

	ret = dvb_register_frontend(&dvb->dvb_adapter, dvb->fe);
	if (ret < 0) {
		if (dvb->fe->ops.release)
			dvb->fe->ops.release(dvb->fe);
		return ret;
	}

	/*
	 * The firmware seems to enable the TS DMUX clock
	 * under various circumstances.  However, since we know we
	 * might use it, let's just turn it on ourselves here.
	 */
	cx18_write_reg_expect(cx,
			      (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK,
			      CX18_CLOCK_ENABLE2,
			      CX18_DMUX_CLK_MASK,
			      (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK);

	return ret;
}

MODULE_FIRMWARE(FWFILE);