/**
* Gets the software revision of the software in the RLY08
*/
unsigned int getRLY08SoftwareRevision() {
IdleI2C();
StartI2C();
IdleI2C();
while(I2CCONbits.SEN);
// send the address
MasterWriteI2C(writeAddr);
IdleI2C();
// send the register
MasterWriteI2C(RLY08_REGISTER_SOFTWARE_REVISION);
IdleI2C();
StopI2C();
IdleI2C();
StartI2C();
while(I2CCONbits.SEN);
// send the address again with read bit
MasterWriteI2C(readAddr);
IdleI2C();
// read the data
unsigned char data = MasterReadI2C();
IdleI2C();
StopI2C();
return data;
}
// Configure and start temperature sensor
void configStartTempSensor(void)
{
// Set configuration register
StartI2C();
WriteI2C(0x9E); // slave address + W
IdleI2C();
WriteI2C(0xAC); // access configuration
IdleI2C();
WriteI2C(0x00); // set config
IdleI2C();
StopI2C();
// Need at least a 10msec delay (from data sheet)
Delay10KTCYx(40);
// Start temperature conversion
StartI2C();
WriteI2C(0x9E); // slave address + W
IdleI2C();
WriteI2C(0xEE); // start conversion
IdleI2C();
StopI2C();
// Another delay
Delay10KTCYx(40);
}
void rtcInit(void)
{
StartI2C();
WriteI2C(0xD0);
WriteI2C(0x00);
WriteI2C(0x80); //CH = 1 Stop oscillator
WriteI2C(0x48); //Minute
WriteI2C(0x16); //Hour
WriteI2C(0x03); //Tuesday
WriteI2C(0x14); //14
WriteI2C(0x03); //March
WriteI2C(0x17); //2017
StopI2C(); //Stop the I2C Protocol
Delay10KTCYx(250);
Delay10KTCYx(250);
Delay10KTCYx(250);
Delay10KTCYx(250);
//Have to start the Clock again
StartI2C();
WriteI2C(0xD0);
WriteI2C(0x00);
WriteI2C(0x00); //start Clock and set the second hand to Zero
StopI2C();
Delay10KTCYx(250);
Delay10KTCYx(250);
Delay10KTCYx(250);
Delay10KTCYx(250);
}
void EEPROM_write(BYTE devaddr, DWORD addr, BYTE *data, BYTE size)
{
BYTE i = 0;
IdleI2C();
StartI2C();
IdleI2C();
// Dev address
WriteI2C( devaddr << 1 );
IdleI2C();
// Memory address
WriteI2C( addr >> 8 );
IdleI2C();
WriteI2C( addr & 0xFF );
IdleI2C();
// data
for(; i < size; ++i)
{
WriteI2C( data[i] );
IdleI2C();
}
StopI2C();
DelayMs(5);
}
void ITG3200_write(unsigned char reg, unsigned char val) {
StartI2C();
WriteI2C(ITG3200_ADDR_WRITE);
WriteI2C(reg);
WriteI2C(val);
StopI2C();
}
void ADXL345_multiByteWrite(unsigned char startAddress, char* buffer, unsigned char size) {
#if I2C
unsigned char i;
StartI2C();
WriteI2C(ADXL343_ADDR_WRITE);
WriteI2C(startAddress);
for (i = 0; i < size; i++) {
WriteI2C(buffer[i]);
}
StopI2C();
#elif SPI
unsigned char tx = (ADXL345_SPI_WRITE | ADXL345_MULTI_BYTE | (startAddress & 0x3F));
unsigned char i;
SPI_CS_PIN = 0; //CS pin low, ie enable chip
Delay1TCY(); // delay at least 5 ns
WriteSPI(tx); //Send starting write address.
for (i = 0; i < size; i++) {
WriteSPI(buffer[i]);
}
SPI_CS_PIN = 1; //CS pin high, ie disable chip
#endif
}
int16_t PutsMasterI2C (uint8_t adresse, uint8_t *donnees, uint8_t nb_octet)
{
uint8_t j;
if (StartI2C () != 1)
{
return ERREUR_I2C_START;
}
if (WriteI2C ((adresse<<1)) != 1)
{
return ERREUR_I2C_WRITE;
}
for (j=0; j<nb_octet; j++)
{
if (WriteI2C (donnees[j]) != 1)
{
return ERREUR_I2C_WRITE;
}
}
if (StopI2C () != 1)
{
return ERREUR_I2C_STOP;
}
return 1;
}
/*
*------------------------------------------------------------------------------
* void ReadRtcTimeAndDate(UINT8 * buff)
*
* Summary : Read time and date related registers from RTC
*
* Input : UINT8 *buff - buffer pointer to receive the data
*
* Output : None
*
*------------------------------------------------------------------------------
*/
void ReadRtcTimeAndDate(UINT8 * buff)
{
StartI2C();
WriteI2C(DEV_ADDR_RTC);
WriteI2C(RTC_REG_SEC);
StartI2C();
WriteI2C(DEV_ADDR_RTC + 1);
*(buff+0)=ReadI2C(ACK); // Second
*(buff+1)=ReadI2C(ACK); // Minute
*(buff+2)=ReadI2C(ACK); // hour
*(buff+3)=ReadI2C(ACK); // Day
*(buff+4)=ReadI2C(ACK); // date
*(buff+5)=ReadI2C(ACK); // month
*(buff+6)=ReadI2C(NO_ACK); // year
StopI2C();
}
/*********************************************************************
* Function: XEE_RESULT XEEBeginRead(unsigned char control,
* XEE_ADDR address)
*
* PreCondition: XEEInit() is already called.
*
* Input: control - EEPROM control and address code.
* address - Address at which read is to be performed.
*
* Output: XEE_SUCCESS if successful
* other value if failed.
*
* Side Effects: None
*
* Overview: Sets internal address counter to given address.
* Puts EEPROM in sequential read mode.
*
* Note: This function does not release I2C bus.
* User must call XEEEndRead() when read is not longer
* needed; I2C bus will released after XEEEndRead()
* is called.
********************************************************************/
XEE_RESULT XEEBeginRead(unsigned char control, XEE_ADDR address )
{
unsigned char r;
r = XEESetAddr(control, address);
if ( r != XEE_SUCCESS )
return r;
r = XEEClose();
if ( r != XEE_SUCCESS )
return r;
IdleI2C();
StartI2C();
while( EEPROM_SPICON2bits.SEN );
if ( PIR2bits.BCLIF )
return XEE_BUS_COLLISION;
if ( WriteI2C(control+1) )
return XEE_BUS_COLLISION;
IdleI2C();
if ( !EEPROM_SPICON2bits.ACKSTAT )
return XEE_SUCCESS;
return XEE_NAK;
}
/*********************************************************************
* Function: LDByteWriteI2C()
* Input: Control Byte, 8 - bit address, data.
* Overview: Write a byte to low density device at address LowAdd
********************************************************************/
unsigned int LDByteWriteI2C(unsigned char ControlByte, unsigned char LowAdd, unsigned char data)
{
unsigned int ErrorCode1;
unsigned int ErrorCode2;
IdleI2C(); //Ensure Module is Idle
StartI2C(); //Generate Start COndition
WriteI2C(ControlByte); //Write Control byte
IdleI2C();
ErrorCode1 = ACKStatus(); //Return ACK Status
WriteI2C(LowAdd); //Write Low Address
IdleI2C();
ErrorCode2 = ACKStatus(); //Return ACK Status
WriteI2C(data); //Write Data
IdleI2C();
StopI2C(); //Initiate Stop Condition
//EEAckPolling(ControlByte); //Perform ACK polling
if(ErrorCode1 == 0) { printf("ACK 1 not recieved"); }
if(ErrorCode2 == 0) { printf("ACK 2 not recieved"); }
//return(ErrorCode);
}
void MCP3422_config(uint8_t config_byte)
{
StartI2C();
WriteI2C(0xD0); // I2C address (for writing)
WriteI2C(config_byte); // CODE_LOAD command
StopI2C();
}
/*
*------------------------------------------------------------------------------
* void StoreSystemDay(UINT8 day)
*
* Summary : Set new day
*
* Input : UINT8 day - value related to day
*
* Output : None
*
* Nonte : Day value must be between 1 to 7
*------------------------------------------------------------------------------
*/
void StoreSystemDay(UINT8 day)
{
StartI2C();
WriteI2C(DEV_ADDR_RTC);
WriteI2C(RTC_REG_DAY);
WriteI2C(day); //day
StopI2C();
}
/*!
\brief
LCD IO Ports lesen
\return LCD IO Port
*/
unsigned char GetIOLCD(void)
{
unsigned char data = 0x00;
StartI2C(LCD_DEV+1);
data = ReadI2C(0);
StopI2C();
return data;
}
// ******************************************************************************
// * Function Name: I2CWriteByte *
// * Return Value: error condition status *
// * Parameters: EE memory device control, address and data *
// * bytes. *
// * Description: Write single data byte to I2C EE memory *
// * device. This routine can be used for any I2C *
// * EE memory device, which uses 2 bytes of *
// * address data as in the 24LC32A/64A/256A. *
// * *
// ******************************************************************************
void I2CWriteByte( byte Device, word Address, byte Data )
{
// Ensure I2C module is idle
IdleI2C();
// Transmit a Start condition
StartI2C();
// Wait till Start sequence is completed
while(I2CCONbits.SEN );
// Ensure I2C module is idle
IdleI2C();
// Write Slave address and set master for transmission (R/W bit should be 0)
MasterWriteI2C(Device);
// Wait till address is transmitted
while(I2CSTATbits.TBF);
// Test for ACK condition received
while(I2CSTATbits.ACKSTAT);
// Ensure I2C module is idle
IdleI2C();
// Write word address for serial EEPROM
MasterWriteI2C(Address);
// Wait till address is transmitted
while(I2CSTATbits.TBF);
// Test for ACK condition received
while(I2CSTATbits.ACKSTAT);
// Ensure I2C module is idle
IdleI2C();
// Write data byte to serial EEPROM
MasterWriteI2C(Data);
// Wait till address is transmitted
while(I2CSTATbits.TBF);
// Ensure I2C module is idle
IdleI2C();
// send STOP condition
StopI2C();
// Wait till Stop sequence is completed
while(I2CCONbits.PEN);
// Ensure I2C module is idle
IdleI2C();
}
void MCP3422_read3(uint8_t* byte1, uint8_t* byte2, uint8_t* config_byte)
{
StartI2C();
WriteI2C(0xD1); // I2C address (for reading)
*byte1 = ReadI2C();
*byte2 = ReadI2C();
*config_byte = ReadLastI2C();
StopI2C();
}
void MAX5217_load_code(uint8_t value_hi, uint8_t value_lo)
{
StartI2C();
WriteI2C(0x3A); // I2C address (for writing)
WriteI2C(0x01); // CODE_LOAD command
WriteI2C(value_hi); // DAC value <15:8>
WriteI2C(value_lo); // DAC value <7:0>
StopI2C();
}
/*
*------------------------------------------------------------------------------
* void StoreSystemDate(void)
*
* Summary : Set new RTC date
*
* Input : None
*
* Output : None
*
*------------------------------------------------------------------------------
*/
void StoreSystemDate(UINT8 *databuffer)
{
StartI2C();
WriteI2C(DEV_ADDR_RTC);
WriteI2C(RTC_REG_DATE);
WriteI2C(((*(databuffer + 0) & 0x0F)<<4) | (*(databuffer + 1) & 0x0F)); //date
WriteI2C(((*(databuffer + 2) & 0x0F)<<4) | (*(databuffer + 3) & 0x0F)); //month
WriteI2C(((*(databuffer + 4) & 0x0F)<<4) | (*(databuffer + 5) & 0x0F)); //year
StopI2C();
}
/*
*------------------------------------------------------------------------------
* void StoreSystemTime(void)
*
* Summary : Set new RTC time
*
* Input : None
*
* Output : None
*
*------------------------------------------------------------------------------
*/
void StoreSystemTime(UINT8 *databuffer)
{
StartI2C();
WriteI2C(DEV_ADDR_RTC);
WriteI2C(RTC_REG_SEC);
WriteI2C(((*(databuffer + 4) & 0x0F)<<4) | (*(databuffer + 5) & 0x0F)); //sec
WriteI2C(((*(databuffer + 2) & 0x0F)<<4) | (*(databuffer + 3) & 0x0F)); //min
WriteI2C(((*(databuffer + 0) & 0x0F)<<4) | (*(databuffer + 1) & 0x0F)); //hour
StopI2C();
}
/*!
\brief
LCD IO Ports schreiben
\param setCommand an - oder auschalten
\param bits zu setzende bits
*/
void SetIOLCD(unsigned char setCommand, unsigned char bits)
{
if (setCommand == ON)
portLCD |= bits;
else
portLCD &= ~bits;
StartI2C(LCD_DEV);
WriteI2C(portLCD);
StopI2C();
}
void changeRLY08Address(int newAddress) {
StartI2C();
IdleI2C();
while(I2CCONbits.SEN);
MasterWriteI2C(writeAddr);
IdleI2C();
// command register
MasterWriteI2C(RLY08_REGISTER_COMMAND);
IdleI2C();
StartI2C();
while(I2CCONbits.SEN);
MasterWriteI2C(RLY08_CHANGE_ADDRESS_FIRST_COMMAND);
IdleI2C();
MasterWriteI2C(RLY08_CHANGE_ADDRESS_SECOND_COMMAND);
IdleI2C();
MasterWriteI2C(RLY08_CHANGE_ADDRESS_THIRD_COMMAND);
MasterWriteI2C(newAddress);
StopI2C();
}
unsigned char i2c_master_send(unsigned char length, unsigned char *msg) {
for (ic_ptr->outbuflen = 0; ic_ptr->outbuflen < length; ic_ptr->outbuflen++) {
ic_ptr->outbuffer[ic_ptr->outbuflen] = msg[ic_ptr->outbuflen];
}
ic_ptr->outbuflen = length;
ic_ptr->outbufind = 1; // point to the second byte to be sent
ic_ptr->status = I2C_MASTER_SEND_ADDR;
ic_ptr->slave_addr = ic_ptr->outbuffer[0];
StartI2C();
return (0);
}
void internalChangeAddressLine(unsigned char oldAddress, unsigned char value) {
IdleI2C();
StartI2C();
MasterWriteI2C(oldAddress);
IdleI2C();
MasterWriteI2C(0);
IdleI2C();
MasterWriteI2C(value);
IdleI2C();
StopI2C();
IdleI2C();
}
unsigned char readSRF02(char addr, char reg) {
StartI2C();
while (I2CCONbits.SEN);
// send the address
MasterWriteI2C(addr);
IdleI2C();
// send the register
MasterWriteI2C(reg);
IdleI2C();
StopI2C();
IdleI2C();
StartI2C();
while (I2CCONbits.SEN);
// send the address again with read bit
MasterWriteI2C(addr + 1);
IdleI2C();
// read the data
unsigned char data = MasterReadI2C();
StopI2C();
return data;
}
// Configure and start temperature sensor
void stopTempSensor(void)
{
StartI2C();
IdleI2C();
WriteI2C(0x9E); // slave address + W
IdleI2C();
WriteI2C(0x22); // stop conversion
IdleI2C();
StopI2C();
// Another delay
Delay10KTCYx(40);
}
int getRelayStates() {
StartI2C();
IdleI2C();
// send the address
MasterWriteI2C(writeAddr);
IdleI2C();
// send the register
MasterWriteI2C(RLY08_REGISTER_RELAY_STATES);
IdleI2C();
StartI2C();
// send the address again with read bit
MasterWriteI2C(readAddr);
IdleI2C();
// send the register
MasterWriteI2C(RLY08_REGISTER_RELAY_STATES);
// read the data - and send an ACK
int data = MasterReadI2C();
StopI2C();
return(data);
}
unsigned char rtc_get_time (unsigned char address)
{
unsigned char time;
StartI2C();
WriteI2C(0xD0);
WriteI2C(address);
RestartI2C();
WriteI2C(0xD1);
time = ReadI2C();
return (((time & 0xF0) >> 4) * 10) + (time & 0x0F); // BCD to decimal
}
void i2c_setup(void)
{
//-------------------
//Setup I2C
//-------------------
SSPADD = 0x78; //120
OpenI2C(MASTER, SLEW_OFF); //Init I2C module
printf("\n\n\rConfiguring I2C...");
StartI2C();
WriteI2C(0x98);
WriteI2C(0x07); //mode register
WriteI2C(0x00); //Standby mode
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x05); //SPCNT register
WriteI2C(0x00); //No sleep count
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x06); //interrupt register (INTSU)
WriteI2C(0xE4); //shake INT on 3-axis, and tap detect
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x09); //PDET register
WriteI2C(0x84); //tap detection on z-axis
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x08); //SR register
WriteI2C(0x00); //Sample rate at 32/sec
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x0A); //PD register
WriteI2C(0x2F); //test tap detection, debounce
StopI2C();
IdleI2C();
StartI2C();
WriteI2C(0x98);
WriteI2C(0x07); //select the mode register
WriteI2C(0x41); //active mode, int push pull
StopI2C();
printf("Finished!\r\n");
}
/*********************************************************************
* Function: LDPageWriteI2C()
* Input: ControlByte, LowAdd, *wrptr.
* Overview: Write a page of data from array pointed to be wrptr
* starting at LowAdd
* Note: LowAdd must start on a page boundary
********************************************************************/
unsigned int LDPageWriteI2C(unsigned char ControlByte, unsigned char LowAdd, unsigned char *wrptr)
{
IdleI2C(); //wait for bus Idle
StartI2C(); //Generate Start condition
WriteI2C(ControlByte); //send controlbyte for a write
IdleI2C(); //wait for bus Idle
WriteI2C(LowAdd); //send low address
IdleI2C(); //wait for bus Idle
putstringI2C(wrptr); //send data
IdleI2C(); //wait for bus Idle
StopI2C(); //Generate Stop
return(0);
}
void writeSRF02Command(char addr, char reg, char cmd) {
StartI2C();
// Wait till Start sequence is completed
IdleI2C();
MasterWriteI2C(addr);
IdleI2C();
MasterWriteI2C(reg);
IdleI2C();
// command
MasterWriteI2C(cmd);
IdleI2C();
StopI2C();
}
/*********************************************************************
* Function: XEE_RESULT XEEIsBusy(unsigned char control)
*
* PreCondition: XEEInit() is already called.
*
* Input: control - EEPROM control and address code.
*
* Output: XEE_READY if EEPROM is not busy
* XEE_BUSY if EEPROM is busy
* other value if failed.
*
* Side Effects: None
*
* Overview: Requests ack from EEPROM.
*
* Note: None
********************************************************************/
XEE_RESULT XEEIsBusy(unsigned char control)
{
XEE_RESULT r;
IdleI2C(); // ensure module is idle
StartI2C(); // initiate START condition
while ( EEPROM_SPICON2bits.SEN ); // wait until start condition is over
if ( PIR2bits.BCLIF ) // test for bus collision
{
return XEE_BUS_COLLISION; // return with Bus Collision error
}
else
{
if ( WriteI2C( control ) ) // write byte - R/W bit should be 0
return XEE_BUS_COLLISION; // set error for write collision
IdleI2C(); // ensure module is idle
if ( PIR2bits.BCLIF ) // test for bus collision
return XEE_BUS_COLLISION; // return with Bus Collision error
if ( !EEPROM_SPICON2bits.ACKSTAT )
r = XEE_READY;
else
r = XEE_BUSY;
#if 0
while ( EEPROM_SPICON2bits.ACKSTAT ) // test for ACK condition received
{
RestartI2C(); // initiate Restart condition
while ( EEPROM_SPICON2bits.RSEN ); // wait until re-start condition is over
if ( PIR2bits.BCLIF ) // test for bus collision
return XEE_BUS_COLLISION; // return with Bus Collision error
if ( WriteI2C( control ) ) // write byte - R/W bit should be 0
return XEE_BUS_COLLISION; // set error for write collision
IdleI2C(); // ensure module is idle
}
#endif
}
StopI2C(); // send STOP condition
while ( EEPROM_SPICON2bits.PEN ); // wait until stop condition is over
if ( PIR2bits.BCLIF ) // test for bus collision
return XEE_BUS_COLLISION; // return with Bus Collision error
return r;
//return XEE_READY; // return with no error
}