void run(){
#ifdef DEBUG_DWT
volatile unsigned int *DWT_CYCCNT = (volatile unsigned int *)0xE0001004; //address of the register
volatile unsigned int *DWT_CONTROL = (volatile unsigned int *)0xE0001000; //address of the register
volatile unsigned int *SCB_DEMCR = (volatile unsigned int *)0xE000EDFC; //address of the register
*SCB_DEMCR = *SCB_DEMCR | 0x01000000;
*DWT_CONTROL = *DWT_CONTROL | 1 ; // enable the counter
#endif
for(;;){
if(doProcessAudio){
#ifdef DEBUG_AUDIO
setPin(GPIOC, GPIO_Pin_5); // PC5 DEBUG
#endif
#ifdef DEBUG_DWT
*DWT_CYCCNT = 0; // reset the counter
#endif
buffer.split(source);
patches.process(buffer);
buffer.comb(dest);
if(collision){
collision = false;
#ifdef DEBUG_AUDIO
debugToggle();
#endif
}else{
doProcessAudio = false;
}
#ifdef DEBUG_AUDIO
clearPin(GPIOC, GPIO_Pin_5); // PC5 DEBUG
#endif
#ifdef DEBUG_DWT
dwt_count = *DWT_CYCCNT;
#endif
}
}
}
void toggleActiveSlot(){
patches.toggleActiveSlot();
updateLed();
midi.sendPatchParameterNames(); // todo: this should probably be requested from client
}
void updateLed(){
setLed((LedPin)patches.getActiveSlot());
midi.sendCc(LED, getLed() == GREEN ? 42 : 84);
}
void setup(){
// NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0); // 0 bits for preemption, 4 bits for subpriority
/* Set up interrupt controller: 2 bits for priority (0-3),
* 2 bits for sub-priority (0-3). Priorities control which
* interrupts are allowed to preempt one another.
*/
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
/* Increase SysTick priority to be higher than USB interrupt
* priority. USB code stalls inside interrupt and we can't let
* this throw off the SysTick timer.
*/
NVIC_SetPriority(SysTick_IRQn, NVIC_EncodePriority(NVIC_PriorityGroup_2, SYSTICK_PRIORITY, SYSTICK_SUBPRIORITY));
NVIC_SetPriority(DMA1_Stream3_IRQn, NVIC_EncodePriority(NVIC_PriorityGroup_2, 0, 0));
NVIC_SetPriority(DMA1_Stream4_IRQn, NVIC_EncodePriority(NVIC_PriorityGroup_2, 0, 0));
NVIC_SetPriority(SPI2_IRQn, NVIC_EncodePriority(NVIC_PriorityGroup_2, 1, 0));
NVIC_SetPriority(ADC_IRQn, NVIC_EncodePriority(NVIC_PriorityGroup_2, 2, 0));
ledSetup();
setLed(RED);
/* check if we need to DFU boot */
configureDigitalInput(SWITCH_B_PORT, SWITCH_B_PIN, GPIO_PuPd_UP);
if(isPushButtonPressed())
jump_to_bootloader();
adcSetup();
clockSetup();
setupSwitchA(footSwitchCallback);
setupSwitchB(pushButtonCallback);
settings.init();
midi.init(MIDI_CHANNEL);
patches.init();
#ifdef EXPRESSION_PEDAL
#ifndef OWLMODULAR
setupExpressionPedal();
#endif
#endif
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE); // DEBUG
configureDigitalOutput(GPIOB, GPIO_Pin_1); // PB1, DEBUG LED
debugClear();
#ifdef DEBUG_AUDIO
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE); // DEBUG
configureDigitalOutput(GPIOA, GPIO_Pin_7); // PA7 DEBUG
configureDigitalOutput(GPIOC, GPIO_Pin_5); // PC5 DEBUG
clearPin(GPIOC, GPIO_Pin_5); // DEBUG
clearPin(GPIOA, GPIO_Pin_7); // DEBUG
#endif /* DEBUG_AUDIO */
usb_init();
#if SERIAL_PORT == 1
setupSerialPort1(115200);
#elif SERIAL_PORT == 2
setupSerialPort2(115200); // expression pedal
#warning expression pedal jack configured as serial port
#ifdef EXPRESSION_PEDAL
#error invalid configuration
#endif
#endif
#ifdef OWLMODULAR
configureDigitalInput(GPIOB, GPIO_Pin_6, GPIO_PuPd_NOPULL); // PB6 OWL Modular digital input
configureDigitalOutput(GPIOB, GPIO_Pin_7); // PB7 OWL Modular digital output
setPin(GPIOB, GPIO_Pin_7); // PB7 OWL Modular digital output
#endif
codec.setup();
codec.init(settings);
printString("startup\n");
updateBypassMode();
codec.start();
}
void processBlock(){
buffer.split(getProgramVector()->audio_input, getProgramVector()->audio_blocksize);
patches.process(buffer);
buffer.comb(getProgramVector()->audio_output);
}
void setup(){
setLed(GREEN);
// int* foo = new int; // causes reset
registry.init();
patches.init(); // causes reset?
}