/**
* @brief Sets transceiver state
*
* @param trx_cmd needs to be one of the trx commands
*
* @return current trx state
*/
tal_trx_status_t set_trx_state(trx_cmd_t trx_cmd)
{
if (tal_trx_status == TRX_SLEEP)
{
/*
* Since the wake-up procedure relies on the Awake IRQ and
* the global interrupts may be disabled at this point of time,
* we need to make sure that the global interrupts are enabled
* during wake-up procedure.
* Once the TRX is awake, the original state of the global interrupts
* will be restored.
*/
/* Reset wake-up interrupt flag. */
tal_awake_end_flag = false;
/* Set callback function for the awake interrupt. */
pal_trx_irq_init(trx_irq_awake_handler_cb);
/* The pending transceiver interrupts on the microcontroller are cleared. */
pal_trx_irq_flag_clr();
pal_trx_irq_en(); /* Enable transceiver main interrupt. */
/* Save current state of global interrupts. */
ENTER_CRITICAL_REGION();
/* Force enabling of global interrupts. */
ENABLE_GLOBAL_IRQ();
/* Leave trx sleep mode. */
PAL_SLP_TR_LOW();
/* Poll wake-up interrupt flag until set within ISR. */
while (!tal_awake_end_flag);
/* Restore original state of global interrupts. */
LEAVE_CRITICAL_REGION();
/* Clear existing interrupts */
pal_trx_reg_read(RG_IRQ_STATUS);
/* Re-install default IRQ handler for main interrupt. */
pal_trx_irq_init(trx_irq_handler_cb);
/* Re-enable TRX_END interrupt */
pal_trx_reg_write(RG_IRQ_MASK, TRX_IRQ_DEFAULT);
#if (ANTENNA_DIVERSITY == 1)
/* Enable antenna diversity. */
pal_trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_ENABLE);
#endif
#ifdef EXT_RF_FRONT_END_CTRL
/* Enable RF front end control */
pal_trx_bit_write(SR_PA_EXT_EN, 1);
#endif
tal_trx_status = TRX_OFF;
if ((trx_cmd == CMD_TRX_OFF) || (trx_cmd == CMD_FORCE_TRX_OFF))
{
return TRX_OFF;
}
}
#ifdef ENABLE_DEEP_SLEEP
else if (tal_trx_status == TRX_DEEP_SLEEP)
{
/* Leave trx sleep mode. */
PAL_SLP_TR_LOW();
/* Check if trx has left deep sleep. */
tal_trx_status_t trx_state;
do
{
trx_state = (tal_trx_status_t)pal_trx_reg_read(RG_TRX_STATUS);
}
while (trx_state != TRX_OFF);
tal_trx_status = TRX_OFF;
/* Using deep sleep, the transceiver's registers need to be restored. */
trx_config();
/*
* Write all PIB values to the transceiver
* that are needed by the transceiver itself.
*/
write_all_tal_pib_to_trx(); /* implementation can be found in 'tal_pib.c' */
if ((trx_cmd == CMD_TRX_OFF) || (trx_cmd == CMD_FORCE_TRX_OFF))
{
return TRX_OFF;
}
}
#endif
switch (trx_cmd) /* requested state */
{
case CMD_SLEEP:
#ifdef ENABLE_DEEP_SLEEP
/* Fall through. */
case CMD_DEEP_SLEEP:
#endif
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
#if (ANTENNA_DIVERSITY == 1)
/*
* Disable antenna diversity: to reduce the power consumption or
* avoid leakage current of an external RF switch during SLEEP.
*/
pal_trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_DISABLE);
#endif
#ifdef EXT_RF_FRONT_END_CTRL
/* Disable RF front end control */
pal_trx_bit_write(SR_PA_EXT_EN, 0);
#endif
/* Clear existing interrupts */
pal_trx_reg_read(RG_IRQ_STATUS);
/*
* Enable Awake_end interrupt.
* This is used for save wake-up from sleep later.
*/
pal_trx_bit_write(SR_IRQ_MASK, TRX_IRQ_4_CCA_ED_DONE);
#ifdef ENABLE_DEEP_SLEEP
if (trx_cmd == CMD_DEEP_SLEEP)
{
pal_trx_reg_write(RG_TRX_STATE, CMD_PREP_DEEP_SLEEP);
tal_trx_status = TRX_DEEP_SLEEP;
}
else
{
/*
* Enable Awake_end interrupt.
* This is used for save wake-up from sleep later.
*/
pal_trx_bit_write(SR_IRQ_MASK, TRX_IRQ_4_CCA_ED_DONE);
tal_trx_status = TRX_SLEEP;
}
#else
/*
* Enable Awake_end interrupt.
* This is used for save wake-up from sleep later.
*/
pal_trx_bit_write(SR_IRQ_MASK, TRX_IRQ_4_CCA_ED_DONE);
tal_trx_status = TRX_SLEEP;
#endif
PAL_WAIT_1_US();
PAL_SLP_TR_HIGH();
pal_timer_delay(TRX_OFF_TO_SLEEP_TIME_CLKM_CYCLES);
/* Transceiver register cannot be read during TRX_SLEEP or DEEP_SLEEP. */
return tal_trx_status;
case CMD_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_FORCE_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_PLL_ON:
switch (tal_trx_status)
{
case PLL_ON:
break;
case TRX_OFF:
switch_pll_on();
break;
case RX_ON:
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_FORCE_PLL_ON:
switch (tal_trx_status)
{
case TRX_OFF:
switch_pll_on();
break;
case PLL_ON:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_PLL_ON);
break;
}
break;
case CMD_RX_ON:
switch (tal_trx_status)
{
case RX_ON:
break;
case PLL_ON:
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_RX_AACK_ON:
switch (tal_trx_status)
{
case RX_AACK_ON:
break;
case TX_ARET_ON:
case PLL_ON:
case RX_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on(); // state change from TRX_OFF to RX_AACK_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_TX_ARET_ON:
switch (tal_trx_status)
{
case TX_ARET_ON:
break;
case PLL_ON:
case RX_ON:
case RX_AACK_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on(); // state change from TRX_OFF to TX_ARET_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
default:
/* CMD_NOP, CMD_TX_START */
ASSERT("trx command not handled" == 0);
break;
}
do
{
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
}
while (tal_trx_status == STATE_TRANSITION_IN_PROGRESS);
return tal_trx_status;
} /* set_trx_state() */
/*
* \brief Sets transceiver state
*
* \param trx_cmd needs to be one of the trx commands
*
* \return current trx state
*/
tal_trx_status_t set_trx_state(trx_cmd_t trx_cmd)
{
if (tal_trx_status == TRX_SLEEP) {
/*
* Since the wake-up procedure relies on the Awake IRQ and
* the global interrupts may be disabled at this point of time,
* we need to make sure that the global interrupts are enabled
* during wake-up procedure.
* Once the TRX is awake, the original state of the global
*interrupts
* will be restored.
*/
/* Reset wake-up interrupt flag. */
if (CMD_SLEEP == trx_cmd) {
return TRX_SLEEP;
}
tal_awake_end_flag = false;
/* Set callback function for the awake interrupt. */
pal_trx_irq_init_awake((FUNC_PTR)trx_awake_handler_cb);
/* Save current state of global interrupts. */
ENTER_CRITICAL_REGION();
/* Force enabling of global interrupts. */
ENABLE_GLOBAL_IRQ();
/* Leave trx sleep mode. */
TRX_SLP_TR_LOW();
/* Poll wake-up interrupt flag until set within ISR. */
while (!tal_awake_end_flag) {
}
/* Restore original state of global interrupts. */
LEAVE_CRITICAL_REGION();
/* Clear existing interrupts */
trx_reg_write(RG_IRQ_STATUS, 0xFF);
/* Re-enable TRX_END interrupt */
trx_reg_write(RG_IRQ_MASK, TRX_IRQ_DEFAULT);
#if (ANTENNA_DIVERSITY == 1)
/* Enable antenna diversity. */
trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_ENABLE);
#endif
if ((trx_cmd == CMD_TRX_OFF) ||
(trx_cmd == CMD_FORCE_TRX_OFF)) {
tal_trx_status = TRX_OFF;
return TRX_OFF;
}
}
switch (trx_cmd) { /* requested state */
case CMD_SLEEP:
trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
#if (ANTENNA_DIVERSITY == 1)
/* Disable antenna diversity: sets pulls */
trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_DISABLE);
#endif
{
uint16_t rand_value;
/*
* Init the SEED value of the CSMA backoff algorithm.
*/
rand_value = (uint16_t)rand();
trx_reg_write(RG_CSMA_SEED_0, (uint8_t)rand_value);
trx_bit_write(SR_CSMA_SEED_1,
(uint8_t)(rand_value >> 8));
}
/*
* Clear existing interrupts to have clear interrupt flags
* during wake-up.
*/
trx_reg_write(RG_IRQ_STATUS, 0xFF);
/*
* Enable Awake_end interrupt.
* This is used for save wake-up from sleep later.
*/
trx_reg_write(RG_IRQ_MASK, TRX_IRQ_AWAKE_ONLY);
PAL_WAIT_1_US();
TRX_SLP_TR_HIGH();
pal_timer_delay(TRX_OFF_TO_SLEEP_TIME_CLKM_CYCLES);
tal_trx_status = TRX_SLEEP;
return TRX_SLEEP; /* transceiver register cannot be read during
*TRX_SLEEP */
case CMD_TRX_OFF:
switch (tal_trx_status) {
case TRX_OFF:
break;
default:
trx_reg_write(RG_TRX_STATE, CMD_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_FORCE_TRX_OFF:
switch (tal_trx_status) {
case TRX_OFF:
break;
default:
trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_PLL_ON:
switch (tal_trx_status) {
case PLL_ON:
break;
case TRX_OFF:
switch_pll_on();
break;
case RX_ON:
case RX_AACK_ON:
case TX_ARET_ON:
trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
case CMD_FORCE_PLL_ON:
switch (tal_trx_status) {
case TRX_OFF:
switch_pll_on();
break;
case PLL_ON:
break;
default:
trx_reg_write(RG_TRX_STATE, CMD_FORCE_PLL_ON);
break;
}
break;
case CMD_RX_ON:
switch (tal_trx_status) {
case RX_ON:
break;
case PLL_ON:
case RX_AACK_ON:
case TX_ARET_ON:
trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
case CMD_RX_AACK_ON:
switch (tal_trx_status) {
case RX_AACK_ON:
break;
case TX_ARET_ON:
case PLL_ON:
trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on(); /* state change from TRX_OFF to
* RX_AACK_ON can be done directly, too */
trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case RX_ON:
trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
/* check if state change could be applied */
tal_trx_status = (tal_trx_status_t)trx_bit_read(
SR_TRX_STATUS);
if (tal_trx_status != PLL_ON) {
return tal_trx_status;
}
trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
case CMD_TX_ARET_ON:
switch (tal_trx_status) {
case TX_ARET_ON:
break;
case PLL_ON:
trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case RX_ON:
case RX_AACK_ON:
trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
/* check if state change could be applied */
tal_trx_status = (tal_trx_status_t)trx_bit_read(
SR_TRX_STATUS);
if (tal_trx_status != PLL_ON) {
return tal_trx_status;
}
trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on(); /* state change from TRX_OFF to
* TX_ARET_ON can be done directly, too */
trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
default:
/* CMD_NOP, CMD_TX_START */
Assert("trx command not handled" == 0);
break;
}
do {
tal_trx_status = (tal_trx_status_t)trx_bit_read(SR_TRX_STATUS);
} while (tal_trx_status == STATE_TRANSITION_IN_PROGRESS);
return tal_trx_status;
} /* set_trx_state() */
static tal_trx_status_t set_trx_state(trx_cmd_t trx_cmd)
{
tal_trx_status = (tal_trx_status_t) pal_trx_bit_read(SR_TRX_STATUS);
/*
* State transition is handled among FORCE_TRX_OFF, RX_ON and PLL_ON.
* These are the essential states required for a basic transmission
* and reception.
*/
switch (trx_cmd) { /* requested state */
case CMD_FORCE_TRX_OFF:
/* Handling FORCE_TRX_OFF state */
switch (tal_trx_status) {
case TRX_OFF:
/* Do nothing - maintain the previous state */
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_PLL_ON:
/* Handling PLL_ON state */
switch (tal_trx_status) {
case PLL_ON:
/* Do nothing - maintain the previous state */
break;
case TRX_OFF:
switch_pll_on();
break;
case RX_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
case CMD_RX_ON:
/* Handling the RX_ON state */
switch (tal_trx_status) {
case RX_ON:
/* Do nothing - maintain the previous state */
break;
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
default:
Assert("state transition not handled" == 0);
break;
}
break;
default:
Assert("trx command not handled" == 0);
break;
}
/* Hold till the state transition is complete */
do {
tal_trx_status = (tal_trx_status_t)
pal_trx_bit_read(SR_TRX_STATUS);
} while (tal_trx_status == STATE_TRANSITION_IN_PROGRESS);
return tal_trx_status;
}
/**
* @brief Sets transceiver state
*
* @param trx_cmd needs to be one of the trx commands
*
* @return current trx state
*/
tal_trx_status_t set_trx_state(trx_cmd_t trx_cmd)
{
if (tal_trx_status == TRX_SLEEP)
{
uint8_t bit_status;
PAL_SLP_TR_LOW();
do
{
bit_status = pal_trx_bit_read(SR_TRX_STATUS);
} while (bit_status != TRX_OFF);
if ((trx_cmd == CMD_TRX_OFF) || (trx_cmd == CMD_FORCE_TRX_OFF))
{
tal_trx_status = TRX_OFF;
return TRX_OFF;
}
}
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
switch (trx_cmd) /* new state */
{
case CMD_TRX_SLEEP:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
{
uint16_t rand_value;
/*
* Init the SEED value of the CSMA backoff algorithm.
*/
rand_value = (uint16_t)rand();
pal_trx_reg_write(RG_CSMA_SEED_0, (uint8_t)rand_value);
pal_trx_bit_write(SR_CSMA_SEED_1, (uint8_t)(rand_value >> 8));
}
PAL_WAIT_1_US();
PAL_SLP_TR_HIGH();
pal_timer_delay(TRX_OFF_TO_SLEEP_TIME);
tal_trx_status = TRX_SLEEP;
return TRX_SLEEP; /* transceiver register cannot be read during TRX_SLEEP */
//break; // do not use break, since it is unreachable
case CMD_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_FORCE_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_SLP_TR_HIGH();
pal_timer_delay(2);
PAL_SLP_TR_LOW();
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_PLL_ON:
switch (tal_trx_status)
{
case PLL_ON:
break;
case TRX_OFF:
switch_pll_on();
break;
case RX_ON:
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_FORCE_PLL_ON: /* software state */
switch (tal_trx_status)
{
case RX_ON:
case BUSY_RX:
case RX_AACK_ON:
case BUSY_RX_AACK:
ENTER_TRX_REGION();
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
// clear trx irq in case a frame is received meanwhile
pal_trx_reg_read(RG_IRQ_STATUS);
pal_trx_irq_flag_clr();
LEAVE_TRX_REGION();
PAL_WAIT_1_US();
break;
case BUSY_TX:
ENTER_TRX_REGION();
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
LEAVE_TRX_REGION();
PAL_WAIT_1_US();
break;
case BUSY_TX_ARET:
ENTER_TRX_REGION();
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_SLP_TR_LOW();
pal_timer_delay(SLP_TR_TOGGLE_US);
PAL_SLP_TR_HIGH();
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
LEAVE_TRX_REGION();
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
break;
case PLL_ON:
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_RX_ON:
switch (tal_trx_status)
{
case RX_ON:
break;
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
// check if state change could be applied
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
if (tal_trx_status != PLL_ON)
{
return tal_trx_status;
}
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_RX_AACK_ON:
switch (tal_trx_status)
{
case RX_AACK_ON:
break;
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();// state change from TRX_OFF to RX_AACK_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case TX_ARET_ON:
case RX_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
// check if state change could be applied
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
if (tal_trx_status != PLL_ON)
{
return tal_trx_status;
}
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_TX_ARET_ON:
switch (tal_trx_status)
{
case TX_ARET_ON:
break;
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case RX_ON:
case RX_AACK_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
// check if state change could be applied
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
if (tal_trx_status != PLL_ON)
{
return tal_trx_status;
}
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();// state change from TRX_OFF to TX_ARET_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
default:
/* CMD_NOP, CMD_TX_START */
ASSERT("trx command not handled" == 0);
break;
}
do
{
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
} while (tal_trx_status == STATE_TRANSITION_IN_PROGRESS);
return tal_trx_status;
} /* set_trx_state() */
/**
* @brief Sets transceiver state
*
* @param trx_cmd needs to be one of the trx commands
*
* @return current trx state
*/
tal_trx_status_t set_trx_state(trx_cmd_t trx_cmd)
{
if (tal_trx_status == TRX_SLEEP)
{
uint8_t bit_status;
uint8_t cnt;
tryagain:
cnt = 100;
PAL_SLP_TR_LOW();
/* poll status register until TRX_OFF is reached */
do
{
bit_status = pal_trx_bit_read(SR_TRX_STATUS);
if (bit_status != TRX_OFF)
{
if (--cnt == 0)
{
/* Work around for trx being "half awake". */
PAL_SLP_TR_HIGH();
goto tryagain;
}
PAL_WAIT_1_US();
}
} while (bit_status != TRX_OFF);
#if (DEBUG > 0)
pal_trx_reg_read(RG_IRQ_STATUS); /* clear Wake irq, dummy read */
#endif
#ifdef ANTENNA_DIVERSITY
/* Enable antenna diversity. */
pal_trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_SWITCH_ENABLE);
#endif
if ((trx_cmd == CMD_TRX_OFF) || (trx_cmd == CMD_FORCE_TRX_OFF))
{
tal_trx_status = TRX_OFF;
return TRX_OFF;
}
}
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
switch (trx_cmd) /* requested state */
{
case CMD_SLEEP:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
#ifdef ANTENNA_DIVERSITY
/* Disable antenna diversity: sets pulls */
pal_trx_bit_write(SR_ANT_EXT_SW_EN, ANT_EXT_SW_SWITCH_DISABLE);
#endif
{
uint16_t rand_value;
/*
* Init the SEED value of the CSMA backoff algorithm.
*/
rand_value = (uint16_t)rand();
pal_trx_reg_write(RG_CSMA_SEED_0, (uint8_t)rand_value);
pal_trx_bit_write(SR_CSMA_SEED_1, (uint8_t)(rand_value >> 8));
}
PAL_WAIT_1_US();
PAL_SLP_TR_HIGH();
pal_timer_delay(TRX_OFF_TO_SLEEP_TIME);
tal_trx_status = TRX_SLEEP;
return TRX_SLEEP; /* transceiver register cannot be read during TRX_SLEEP */
case CMD_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_FORCE_TRX_OFF:
switch (tal_trx_status)
{
case TRX_OFF:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_TRX_OFF);
PAL_WAIT_1_US();
break;
}
break;
case CMD_PLL_ON:
switch (tal_trx_status)
{
case PLL_ON:
break;
case TRX_OFF:
switch_pll_on();
break;
case RX_ON:
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_FORCE_PLL_ON:
switch (tal_trx_status)
{
case TRX_OFF:
switch_pll_on();
break;
case PLL_ON:
break;
default:
pal_trx_reg_write(RG_TRX_STATE, CMD_FORCE_PLL_ON);
break;
}
break;
case CMD_RX_ON:
switch (tal_trx_status)
{
case RX_ON:
break;
case PLL_ON:
case RX_AACK_ON:
case TX_ARET_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_RX_AACK_ON:
switch (tal_trx_status)
{
case RX_AACK_ON:
break;
case TX_ARET_ON:
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();// state change from TRX_OFF to RX_AACK_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case RX_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
// check if state change could be applied
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
if (tal_trx_status != PLL_ON)
{
return tal_trx_status;
}
pal_trx_reg_write(RG_TRX_STATE, CMD_RX_AACK_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
case CMD_TX_ARET_ON:
switch (tal_trx_status)
{
case TX_ARET_ON:
break;
case PLL_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case RX_ON:
case RX_AACK_ON:
pal_trx_reg_write(RG_TRX_STATE, CMD_PLL_ON);
PAL_WAIT_1_US();
// check if state change could be applied
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
if (tal_trx_status != PLL_ON)
{
return tal_trx_status;
}
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case TRX_OFF:
switch_pll_on();// state change from TRX_OFF to TX_ARET_ON can be done directly, too
pal_trx_reg_write(RG_TRX_STATE, CMD_TX_ARET_ON);
PAL_WAIT_1_US();
break;
case BUSY_RX:
case BUSY_TX:
case BUSY_RX_AACK:
case BUSY_TX_ARET:
/* do nothing if trx is busy */
break;
default:
ASSERT("state transition not handled" == 0);
break;
}
break;
default:
/* CMD_NOP, CMD_TX_START */
ASSERT("trx command not handled" == 0);
break;
}
do
{
tal_trx_status = (tal_trx_status_t)pal_trx_bit_read(SR_TRX_STATUS);
} while (tal_trx_status == STATE_TRANSITION_IN_PROGRESS);
return tal_trx_status;
} /* set_trx_state() */
