| Hardware | description |
|---|---|
| CPU | SAMSUNG S3C6410, run at 533Mhz, up to 667Mhz |
| Board | Tiny6410 (v1308) |
| Expander Board | Tiny6410SDK(TinyADK 1312B) with 7"LCD |
| folder | description |
|---|---|
| arm-asm | ARM-S3C6410 Assembler |
| no-os | ARM-S3C6410 Bare-Metal Program |
| linux | ARM-S3C6410 Linux Program |
| doc | ARM-S3C6410 documents |
##核心板: Tiny6410 - v1308 SDRAM: SAMSUNG K4X2G323PD-8GD8 Mobile DDR 64Mx32 200Mhz Halogen Free FBGA90 DRAM 64Mbx32 = 2048Mb = 2Gb = 256MB
NAND FLASH: SAMSUNG K9K8G08U0E-SCB0, 8G bit Nand Flash 1Gx8 SLC
LED: LED1 ~ LED4 (nLED_1 ~ nLED_4), 低电平点亮LED.
LED1 - GPK4
LED2 - GPK5
LED3 - GPK6
LED4 - GPK7
JTAG: 10 pin 2.0mm space Jtag connector
Button: Reset button, 连接M_nRESET接口, 低电平有效;
Power: Supply Voltage from 2.0V to 6V
Crystal: Y1 - 12M - ( XTO , XTI ) - 外部时钟
Y2 - 27M - ( 27MXTO , 27MXTI ) - X27MXTO
Y3 - 48M - ( OTGTO , OTGTI ) - USB OTG 时钟
Y4 - 32.768K - ( RTCTO , RTCTI ) - RTC 时钟
####NAND FLASH:
SAMSUNG K9K8G08U0E-SCB0, 8G bit Nand Flash,1Gx8 SLC
K9F4G08U0E , K9K8G08U0E, 同一个芯片手册;
型号说明： http://www.elnec.com/device/Samsung/K9F4G08U0E+%5BTSOP48%5D/
- K = Memory
- 9 = NAND Flash
- F = SLC Normal ; K = SLC Die Normal, SLC Die stack;
- Density: 4G = 4Gbit, 8G = 8Gbit;
- Technology: 0 = Normal (x8)
- Organization: 8 = x8
- Supply Voltage: U = 2.7V to 3.6V
- Mode: 0 = Normal
- Generation: E = 6th generation
####SDRAM - K4X2G323PD-8GD8 http://www.samsung.com/us/business/oem-solutions/pdfs/PSG_2H_2012.pdf
K4X2G323PD-8GD8
K: SAMSUNG Memort
4: DRAM
X: Mobile DDR SDRAM
2G: 2G, 8K/64ms
32: x32 (bit organization) 3: 4 of Internal Banks
P: LVTTL, 1.8V, 1.8V
D: 5th Generation
S/D: 90balls FBGA
====== ###扩展底层板: Tiny6410SDK 增强版 - TinyADK 1312B
Button: K1 - XEINT16
K2 - XEINT17
K3 - XEINT18
K4 - XEINT19
Button IO接上拉电阻，按下按键后IO为拉为低电平;
Buzzer: XpwmTOUT0 (XpwmTOUT0/XCLKOUT/GPF14)
I2C-EEPROM: ATMLH346
Xi2cSCL0, Xi2cSDA0
###FriendlyARM Tiny6410 下载程序 - MiniTools.exe
-
底层板S2选择NAND启动方式
-
按住K1按钮，打开电源开关S1
-
此时若串口连接COM0到PC，配置波特率为115200，就可以看到串口输出消息; 不进行串口连接，也可以在液晶屏上看到同样的消息;
-
输出消息:
Booting from NAND Superboot6410 Ver: 141011 CPU: S3C6410 533MHz RAM: 256MB NAND: 1GB(SLC) ID:ECD35195 Touch Device: 1-wire LCD Type: S70(Auto) USB Mode: Waiting... Hello USB Loop -
底层板通过USB与PC连接，PC识别USB设备。打开MiniTools.exe软件，识别到ARM开发板;
-
同时串口输出消息:
USB Mode: Connected -
选择不同模式，下载程序;
注意：必须先给板子上电，然后在打开MiniTools.exe, 否则MiniTools.exe会卡死无响应。
###FriendlyARM Tiny6410 下载程序 - SDHC