Linux Software Guide for TSP Boards

1. Introduction
- This package cantains the linux device driver and application for  TSP/TVB Boards
- Compiled and tested under the Red Hat Fedora(2.6.9.???),

2. How to use sample programs

(TSP102 board)
1. make driver, low level dll, sample application
* make all 
* output : tsp102.o p102 r102 ./lld/tsplld0421.o 
2. load tsp102 driver (root privilege required)
* ./l 102
3. play or record stream
* ./p102 streamfile 19392658 1
* ./r102 capturefile 310M|ASI 1
4. unload driver (root privilege required)
* ./u 102

(Tvb140/Tqk150/Tom160 board)
1. make driver, low level dll, sample application
* make all 
* output : tvb140.o/tqk150.o/tom160.o 
p140/p150/p160
t140/t150/t160
./lld/tsplld042x.o
./t??tune/t??_tune.o
2. load driver (root privilege required)
* ./l 140/150/160
3. play or record stream using p140/p150/160 or t140/t150/t160
* /p140 streams 19392658 1
* t140 freq capturefile
4. unload driver (root privilege required)
* ./u 140/150/160

(Tvb360 board)
1. make driver, low level dll, sample application
* make all 
* output : tvb360.o p360 ./lld/tsplld0425.o 
2. load tvb360 driver (root privilege required)
* ./l 360
3. set modulator parameter
* ./p360 modulation_mode input freq symbol coding mode
4. unload driver (root privilege required)
* ./u 360

(Tvb380 board)
1. make driver, low level dll, sample application
* make all
* output : tvb380v4.o(ko) mod_??? ./lld/tsplld0381.o
2. load tvb380 driver (root privilege required)
* ./l 380
3. set play/modulator parameter
* ./mod_?????
4. unload driver (root privilege required)
* ./u 380
5. If you have new TVB380(Revision #3), check the following CFLAG must be included at Makefile.
	...
	EXTRA_CFLAGS += -DTVB380
	EXTRA_CFLAGS += -DTVB390V8

(Tvb390 board)
1. make driver, low level dll, sample application
* make all
* output : tvb380v4.o(ko) mod_??? ./lld/tsplld0381.o
2. load tvb390 driver (root privilege required)
* ./l 390
3. set play/modulator parameter
* ./mod_????? 
4. unload driver (root privilege required)
* ./u 390
5. If you have new TVB390V7, check the following CFLAG must be included at Makefile.
	...
	EXTRA_CFLAGS += -DTVB380V4
	EXTRA_CFLAGS += -DTVB390V8

(Tvb590 board)
0. If one uses TVB590 boards, follow this procedures instead of the above Tvb390 case

1. make driver, low level dll, sample application
* make all
* output : tvb380v4.o(ko) mod_??? ./lld/tsplld0381.o
2. load tvb390 driver (root privilege required)
* ./l 590
3. set play/modulator parameter
* ./mod_?????
4. unload driver (root privilege required)
* ./u 590
5. If you have new TVB590(TVB390V8 or higher), check the following EXTRA_CFLAGS is included at Makefile.
        ...
        EXTRA_CFLAGS += -DTVB380V4
        EXTRA_CFLAGS += -DTVB390V8

        And comment the following line if it is neither TVB595 nor TVB597A.
        #EXTRA_CFLAGS += -DTVB595V1
	
And, uncomment only the line "(cd ./lld; make -f Makefile.380 clean; make -f Makefile.380)" for lld build.

(Tvb595/Tvb597A board)
0. No driver load/unload procedure is not needed, but usb host management is supported by "libusb-0.1.12" tools.
1. If you have new TVB595, check the following CFLAG must be included at Makefile.
        ...
        EXTRA_CFLAGS += -DTVB380V4
        EXTRA_CFLAGS += -DTVB390V8
        EXTRA_CFLAGS += -DTVB595V1

And, uncomment only the line "(cd ./lld; make -f Makefile.595 clean; make -f Makefile.595)" for lld build.

(Tvb590E board)
0. If PCI-express performance is too low, before both loading device driver and building application, 
1. Run ./p .
2. It will create and install a helper library and a service driver for TVB590E performance.

(Tvb370 board)
1. make driver, low level dll, sample application
* make all
* output : tvb370v6.o(ko) p390_??? ./lld/tsplld0381.o
2. load tvb370 driver (root privilege required)
* ./l 370
3. set play/modulator parameters
* ./p390_vsb
4. unload driver (root privilege required)
* ./u 370

5. If you have new TVB370/8VSB, check the following EXTRA_CFLAGS is included at Makefile.
	...
	EXTRA_CFLAGS += -DTVB370V6

6. If you have new TVB370/IF, check the following EXTRA_CFLAGS is included at Makefile.
	...
	EXTRA_CFLAGS += -DTVB370V6	
	EXTRA_CFLAGS += -DTVB390V8

And, uncomment only the line "(cd ./lld; make -f Makefile.370 clean; make -f Makefile.370)" for lld build.

(Tse110 board)
1. make driver, low level dll, sample application
* make all
* output : tse110v1.o(ko) lld_ ./lld/tsplld0431.o
2. load tse110 driver (root privilege required)
* ./l 110
3. set play/record parameters
* ./lld_tse110
4. unload driver (root privilege required)
* ./u 110

5. Check the following EXTRA_CFLAGS is included at Makefile.
	...
	EXTRA_CFLAGS += -DTSE110V1

And, uncomment only the line "(cd ./lld; make -f Makefile.110 clean; make -f Makefile.110)" for lld build.