/*
* Probe a i2400m interface and register it
*
* @iface: USB interface to link to
* @id: USB class/subclass/protocol id
* @returns: 0 if ok, < 0 errno code on error.
*
* Alloc a net device, initialize the bus-specific details and then
* calls the bus-generic initialization routine. That will register
* the wimax and netdev devices, upload the firmware [using
* _bus_bm_*()], call _bus_dev_start() to finalize the setup of the
* communication with the device and then will start to talk to it to
* finnish setting it up.
*/
static
int i2400mu_probe(struct usb_interface *iface,
const struct usb_device_id *id)
{
int result;
struct net_device *net_dev;
struct device *dev = &iface->dev;
struct i2400m *i2400m;
struct i2400mu *i2400mu;
struct usb_device *usb_dev = interface_to_usbdev(iface);
if (usb_dev->speed != USB_SPEED_HIGH)
dev_err(dev, "device not connected as high speed\n");
/* Allocate instance [calls i2400m_netdev_setup() on it]. */
result = -ENOMEM;
net_dev = alloc_netdev(sizeof(*i2400mu), "wmx%d",
i2400mu_netdev_setup);
if (net_dev == NULL) {
dev_err(dev, "no memory for network device instance\n");
goto error_alloc_netdev;
}
SET_NETDEV_DEV(net_dev, dev);
SET_NETDEV_DEVTYPE(net_dev, &i2400mu_type);
i2400m = net_dev_to_i2400m(net_dev);
i2400mu = container_of(i2400m, struct i2400mu, i2400m);
i2400m->wimax_dev.net_dev = net_dev;
i2400mu->usb_dev = usb_get_dev(usb_dev);
i2400mu->usb_iface = iface;
usb_set_intfdata(iface, i2400mu);
i2400m->bus_tx_block_size = I2400MU_BLK_SIZE;
i2400m->bus_pl_size_max = I2400MU_PL_SIZE_MAX;
i2400m->bus_dev_start = i2400mu_bus_dev_start;
i2400m->bus_dev_stop = i2400mu_bus_dev_stop;
i2400m->bus_tx_kick = i2400mu_bus_tx_kick;
i2400m->bus_reset = i2400mu_bus_reset;
i2400m->bus_bm_retries = I2400M_BOOT_RETRIES;
i2400m->bus_bm_cmd_send = i2400mu_bus_bm_cmd_send;
i2400m->bus_bm_wait_for_ack = i2400mu_bus_bm_wait_for_ack;
i2400m->bus_fw_names = i2400mu_bus_fw_names;
i2400m->bus_bm_mac_addr_impaired = 0;
#ifdef CONFIG_PM
iface->needs_remote_wakeup = 1; /* autosuspend (15s delay) */
device_init_wakeup(dev, 1);
usb_autopm_enable(i2400mu->usb_iface);
usb_dev->autosuspend_delay = 15 * HZ;
usb_dev->autosuspend_disabled = 0;
#endif
result = i2400m_setup(i2400m, I2400M_BRI_MAC_REINIT);
if (result < 0) {
dev_err(dev, "cannot setup device: %d\n", result);
goto error_setup;
}
result = i2400mu_debugfs_add(i2400mu);
if (result < 0) {
dev_err(dev, "Can't register i2400mu's debugfs: %d\n", result);
goto error_debugfs_add;
}
return 0;
error_debugfs_add:
i2400m_release(i2400m);
error_setup:
usb_set_intfdata(iface, NULL);
usb_put_dev(i2400mu->usb_dev);
free_netdev(net_dev);
error_alloc_netdev:
return result;
}
/* ath6kl usb driver registered functions */
static int ath6kl_usb_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_device *dev = interface_to_usbdev(interface);
struct ath6kl *ar;
struct ath6kl_usb *ar_usb = NULL;
int vendor_id, product_id;
int ret = 0;
usb_get_dev(dev);
vendor_id = le16_to_cpu(dev->descriptor.idVendor);
product_id = le16_to_cpu(dev->descriptor.idProduct);
ath6kl_dbg(ATH6KL_DBG_USB, "vendor_id = %04x\n", vendor_id);
ath6kl_dbg(ATH6KL_DBG_USB, "product_id = %04x\n", product_id);
if (interface->cur_altsetting)
ath6kl_dbg(ATH6KL_DBG_USB, "USB Interface %d\n",
interface->cur_altsetting->desc.bInterfaceNumber);
if (dev->speed == USB_SPEED_HIGH)
ath6kl_dbg(ATH6KL_DBG_USB, "USB 2.0 Host\n");
else
ath6kl_dbg(ATH6KL_DBG_USB, "USB 1.1 Host\n");
ar_usb = ath6kl_usb_create(interface);
if (ar_usb == NULL) {
ret = -ENOMEM;
goto err_usb_put;
}
ar = ath6kl_core_create(&ar_usb->udev->dev);
if (ar == NULL) {
ath6kl_err("Failed to alloc ath6kl core\n");
ret = -ENOMEM;
goto err_usb_destroy;
}
ar->hif_priv = ar_usb;
ar->hif_type = ATH6KL_HIF_TYPE_USB;
ar->hif_ops = &ath6kl_usb_ops;
ar->mbox_info.block_size = 16;
ar->bmi.max_data_size = 252;
ar_usb->ar = ar;
ret = ath6kl_core_init(ar);
if (ret) {
ath6kl_err("Failed to init ath6kl core: %d\n", ret);
goto err_core_free;
}
return ret;
err_core_free:
ath6kl_core_destroy(ar);
err_usb_destroy:
ath6kl_usb_destroy(ar_usb);
err_usb_put:
usb_put_dev(dev);
return ret;
}
static void smdhsic_disconnect(struct usb_interface *intf)
{
int devid;
struct usb_interface *smd_intf;
struct str_intf_priv *intfpriv;
struct usb_device *device = NULL;
pr_info("%s: Called\n", __func__);
intfpriv = usb_get_intfdata(intf);
if (!intfpriv) {
pr_err("%s: intfpriv is NULL\n", __func__);
goto err_get_intfdata;
}
device = get_usb_device(intfpriv);
devid = GET_DEVID(intfpriv->devid);
pr_debug("%s : devid : %d\n", __func__, devid);
smd_intf = get_usb_intf(intfpriv);
if (!smd_intf) {
pr_err("smd_intf is NULL\n");
goto err_get_usb_intf;
}
if (smd_intf != intf) {
pr_err("smd_intf is not same intf\n");
goto err_mismatched_intf;
}
usb_driver_release_interface(get_usb_driver(intf), smd_intf);
if (!device)
usb_put_dev(device);
pm_runtime_disable(&device->dev);
if (g_usbdev.hsic)
cancel_delayed_work(&g_usbdev.hsic->pm_runtime_work);
switch (devid) {
case FMT_DEV_ID:
flush_txurb(&g_usbdev.ipc_urbq);
flush_txurb(&g_usbdev.data_urbq);
smdctl_request_connection_recover(true);
case RAW_DEV_ID:
case RFS_DEV_ID:
case CMD_DEV_ID:
case DOWN_DEV_ID:
if (emu_discon_func[devid])
emu_discon_func[devid](g_usbdev.smd_device[devid]);
else
kfree(intfpriv->data);
break;
default:
pr_warn("%s:Undefined Callback Function\n",
__func__);
}
/* to prevent sleep at connection recover
* when, usb suspend and recover routine overlap
* it makes huge delay on modem reset
*/
wake_lock_timeout(&g_usbdev.txwake, 20*HZ);
kfree(intfpriv);
usb_set_intfdata(intf, NULL);
g_usbdev.usbdev = NULL;
g_usbdev.suspended = 0;
g_usbdev.hsic = NULL;
return;
err_mismatched_intf:
err_get_usb_intf:
if (!device)
usb_put_dev(device);
err_get_intfdata:
pr_err("release(2) : %p\n", intf);
usb_driver_release_interface(get_usb_driver(intf), intf);
return;
}
static int gigaset_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{
int retval;
struct usb_device *udev = interface_to_usbdev(interface);
struct usb_host_interface *hostif = interface->cur_altsetting;
struct cardstate *cs = NULL;
struct usb_cardstate *ucs = NULL;
struct usb_endpoint_descriptor *endpoint;
int buffer_size;
gig_dbg(DEBUG_ANY, "%s: Check if device matches ...", __func__);
/* See if the device offered us matches what we can accept */
if ((le16_to_cpu(udev->descriptor.idVendor) != USB_M105_VENDOR_ID) ||
(le16_to_cpu(udev->descriptor.idProduct) != USB_M105_PRODUCT_ID)) {
gig_dbg(DEBUG_ANY, "device ID (0x%x, 0x%x) not for me - skip",
le16_to_cpu(udev->descriptor.idVendor),
le16_to_cpu(udev->descriptor.idProduct));
return -ENODEV;
}
if (hostif->desc.bInterfaceNumber != 0) {
gig_dbg(DEBUG_ANY, "interface %d not for me - skip",
hostif->desc.bInterfaceNumber);
return -ENODEV;
}
if (hostif->desc.bAlternateSetting != 0) {
dev_notice(&udev->dev, "unsupported altsetting %d - skip",
hostif->desc.bAlternateSetting);
return -ENODEV;
}
if (hostif->desc.bInterfaceClass != 255) {
dev_notice(&udev->dev, "unsupported interface class %d - skip",
hostif->desc.bInterfaceClass);
return -ENODEV;
}
dev_info(&udev->dev, "%s: Device matched ... !\n", __func__);
/* allocate memory for our device state and intialize it */
cs = gigaset_initcs(driver, 1, 1, 0, cidmode, GIGASET_MODULENAME);
if (!cs)
return -ENODEV;
ucs = cs->hw.usb;
/* save off device structure ptrs for later use */
usb_get_dev(udev);
ucs->udev = udev;
ucs->interface = interface;
cs->dev = &interface->dev;
/* save address of controller structure */
usb_set_intfdata(interface, cs); // dev_set_drvdata(&interface->dev, cs);
endpoint = &hostif->endpoint[0].desc;
buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
ucs->bulk_out_size = buffer_size;
ucs->bulk_out_endpointAddr = endpoint->bEndpointAddress;
ucs->bulk_out_buffer = kmalloc(buffer_size, GFP_KERNEL);
if (!ucs->bulk_out_buffer) {
dev_err(cs->dev, "Couldn't allocate bulk_out_buffer\n");
retval = -ENOMEM;
goto error;
}
ucs->bulk_out_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!ucs->bulk_out_urb) {
dev_err(cs->dev, "Couldn't allocate bulk_out_urb\n");
retval = -ENOMEM;
goto error;
}
endpoint = &hostif->endpoint[1].desc;
ucs->busy = 0;
ucs->read_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!ucs->read_urb) {
dev_err(cs->dev, "No free urbs available\n");
retval = -ENOMEM;
goto error;
}
buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
ucs->rcvbuf_size = buffer_size;
ucs->int_in_endpointAddr = endpoint->bEndpointAddress;
cs->inbuf[0].rcvbuf = kmalloc(buffer_size, GFP_KERNEL);
if (!cs->inbuf[0].rcvbuf) {
dev_err(cs->dev, "Couldn't allocate rcvbuf\n");
retval = -ENOMEM;
goto error;
}
/* Fill the interrupt urb and send it to the core */
usb_fill_int_urb(ucs->read_urb, udev,
usb_rcvintpipe(udev,
endpoint->bEndpointAddress & 0x0f),
cs->inbuf[0].rcvbuf, buffer_size,
gigaset_read_int_callback,
cs->inbuf + 0, endpoint->bInterval);
retval = usb_submit_urb(ucs->read_urb, GFP_KERNEL);
if (retval) {
dev_err(cs->dev, "Could not submit URB (error %d)\n", -retval);
goto error;
}
/* tell common part that the device is ready */
if (startmode == SM_LOCKED)
cs->mstate = MS_LOCKED;
if (!gigaset_start(cs)) {
tasklet_kill(&cs->write_tasklet);
retval = -ENODEV; //FIXME
goto error;
}
return 0;
error:
usb_kill_urb(ucs->read_urb);
kfree(ucs->bulk_out_buffer);
usb_free_urb(ucs->bulk_out_urb);
kfree(cs->inbuf[0].rcvbuf);
usb_free_urb(ucs->read_urb);
usb_set_intfdata(interface, NULL);
ucs->read_urb = ucs->bulk_out_urb = NULL;
cs->inbuf[0].rcvbuf = ucs->bulk_out_buffer = NULL;
usb_put_dev(ucs->udev);
ucs->udev = NULL;
ucs->interface = NULL;
gigaset_freecs(cs);
return retval;
}
static void kevent (void *data)
{
struct usbnet *dev = (struct usbnet *)data;
#else
static void kevent (struct work_struct *work)
{
struct usbnet *dev =
container_of(work, struct usbnet, kevent);
#endif
int status;
/* usb_clear_halt() needs a thread context */
if (test_bit (EVENT_TX_HALT, &dev->flags)) {
unlink_urbs (dev, &dev->txq);
status = usb_clear_halt (dev->udev, dev->out);
if (status < 0
&& status != -EPIPE
&& status != -ESHUTDOWN) {
if (netif_msg_tx_err (dev))
deverr (dev, "can't clear tx halt, status %d",
status);
} else {
clear_bit (EVENT_TX_HALT, &dev->flags);
if (status != -ESHUTDOWN)
netif_wake_queue (dev->net);
}
}
if (test_bit (EVENT_RX_HALT, &dev->flags)) {
unlink_urbs (dev, &dev->rxq);
status = usb_clear_halt (dev->udev, dev->in);
if (status < 0
&& status != -EPIPE
&& status != -ESHUTDOWN) {
if (netif_msg_rx_err (dev))
deverr (dev, "can't clear rx halt, status %d",
status);
} else {
clear_bit (EVENT_RX_HALT, &dev->flags);
tasklet_schedule (&dev->bh);
}
}
/* tasklet could resubmit itself forever if memory is tight */
if (test_bit (EVENT_RX_MEMORY, &dev->flags)) {
struct urb *urb = NULL;
if (netif_running (dev->net))
urb = usb_alloc_urb (0, GFP_KERNEL);
else
clear_bit (EVENT_RX_MEMORY, &dev->flags);
if (urb != NULL) {
clear_bit (EVENT_RX_MEMORY, &dev->flags);
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,14)
urb->transfer_flags |= URB_ASYNC_UNLINK;
#endif
rx_submit (dev, urb, GFP_KERNEL);
tasklet_schedule (&dev->bh);
}
}
if (test_bit (EVENT_LINK_RESET, &dev->flags)) {
struct driver_info *info = dev->driver_info;
int retval = 0;
clear_bit (EVENT_LINK_RESET, &dev->flags);
if(info->link_reset && (retval = info->link_reset(dev)) < 0) {
devinfo(dev, "link reset failed (%d) usbnet usb-%s-%s, %s",
retval,
dev->udev->bus->bus_name, dev->udev->devpath,
info->description);
}
}
if (dev->flags)
devdbg (dev, "kevent done, flags = 0x%lx",
dev->flags);
}
/*-------------------------------------------------------------------------*/
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,19)
static void tx_complete (struct urb *urb, struct pt_regs *regs)
#else
static void tx_complete (struct urb *urb)
#endif
{
struct sk_buff *skb = (struct sk_buff *) urb->context;
struct skb_data *entry = (struct skb_data *) skb->cb;
struct usbnet *dev = entry->dev;
if (urb->status == 0) {
dev->stats.tx_packets++;
dev->stats.tx_bytes += entry->length;
} else {
dev->stats.tx_errors++;
switch (urb->status) {
case -EPIPE:
axusbnet_defer_kevent (dev, EVENT_TX_HALT);
break;
/* software-driven interface shutdown */
case -ECONNRESET: // async unlink
case -ESHUTDOWN: // hardware gone
break;
// like rx, tx gets controller i/o faults during khubd delays
// and so it uses the same throttling mechanism.
case -EPROTO:
case -ETIME:
case -EILSEQ:
if (!timer_pending (&dev->delay)) {
mod_timer (&dev->delay,
jiffies + THROTTLE_JIFFIES);
if (netif_msg_link (dev))
devdbg (dev, "tx throttle %d",
urb->status);
}
netif_stop_queue (dev->net);
break;
default:
if (netif_msg_tx_err (dev))
devdbg (dev, "tx err %d", entry->urb->status);
break;
}
}
urb->dev = NULL;
entry->state = tx_done;
defer_bh(dev, skb, &dev->txq);
}
/*-------------------------------------------------------------------------*/
static
void axusbnet_tx_timeout (struct net_device *net)
{
struct usbnet *dev = netdev_priv(net);
unlink_urbs (dev, &dev->txq);
tasklet_schedule (&dev->bh);
// FIXME: device recovery -- reset?
}
/*-------------------------------------------------------------------------*/
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,32)
static int
#else
static netdev_tx_t
#endif
axusbnet_start_xmit (struct sk_buff *skb,
struct net_device *net)
{
struct usbnet *dev = netdev_priv(net);
int length;
struct urb *urb = NULL;
struct skb_data *entry;
struct driver_info *info = dev->driver_info;
unsigned long flags;
int retval;
// some devices want funky USB-level framing, for
// win32 driver (usually) and/or hardware quirks
if (info->tx_fixup) {
skb = info->tx_fixup (dev, skb, GFP_ATOMIC);
if (!skb) {
if (netif_msg_tx_err (dev))
devdbg (dev, "can't tx_fixup skb");
goto drop;
}
}
length = skb->len;
if (!(urb = usb_alloc_urb (0, GFP_ATOMIC))) {
if (netif_msg_tx_err (dev))
devdbg (dev, "no urb");
goto drop;
}
entry = (struct skb_data *) skb->cb;
entry->urb = urb;
entry->dev = dev;
entry->state = tx_start;
entry->length = length;
usb_fill_bulk_urb (urb, dev->udev, dev->out,
skb->data, skb->len, tx_complete, skb);
/* don't assume the hardware handles USB_ZERO_PACKET
* NOTE: strictly conforming cdc-ether devices should expect
* the ZLP here, but ignore the one-byte packet.
*/
if (!(info->flags & FLAG_SEND_ZLP) && (length % dev->maxpacket) == 0) {
urb->transfer_buffer_length++;
if (skb_tailroom(skb)) {
skb->data[skb->len] = 0;
__skb_put(skb, 1);
}
}
spin_lock_irqsave (&dev->txq.lock, flags);
switch ((retval = usb_submit_urb (urb, GFP_ATOMIC))) {
case -EPIPE:
netif_stop_queue (net);
axusbnet_defer_kevent (dev, EVENT_TX_HALT);
break;
default:
if (netif_msg_tx_err (dev))
devdbg (dev, "tx: submit urb err %d", retval);
break;
case 0:
net->trans_start = jiffies;
__skb_queue_tail (&dev->txq, skb);
if (dev->txq.qlen >= TX_QLEN (dev))
netif_stop_queue (net);
}
spin_unlock_irqrestore (&dev->txq.lock, flags);
if (retval) {
if (netif_msg_tx_err (dev))
devdbg (dev, "drop, code %d", retval);
drop:
dev->stats.tx_dropped++;
if (skb)
dev_kfree_skb_any (skb);
usb_free_urb (urb);
} else if (netif_msg_tx_queued (dev)) {
devdbg (dev, "> tx, len %d, type 0x%x",
length, skb->protocol);
}
return NETDEV_TX_OK;
}
/*-------------------------------------------------------------------------*/
// tasklet (work deferred from completions, in_irq) or timer
static void axusbnet_bh (unsigned long param)
{
struct usbnet *dev = (struct usbnet *) param;
struct sk_buff *skb;
struct skb_data *entry;
while ((skb = skb_dequeue (&dev->done))) {
entry = (struct skb_data *) skb->cb;
switch (entry->state) {
case rx_done:
entry->state = rx_cleanup;
rx_process (dev, skb);
continue;
case tx_done:
case rx_cleanup:
usb_free_urb (entry->urb);
dev_kfree_skb (skb);
continue;
default:
devdbg (dev, "bogus skb state %d", entry->state);
}
}
// waiting for all pending urbs to complete?
if (dev->wait) {
if ((dev->txq.qlen + dev->rxq.qlen + dev->done.qlen) == 0) {
wake_up (dev->wait);
}
// or are we maybe short a few urbs?
} else if (netif_running (dev->net)
&& netif_device_present (dev->net)
&& !timer_pending (&dev->delay)
&& !test_bit (EVENT_RX_HALT, &dev->flags)) {
int temp = dev->rxq.qlen;
int qlen = RX_QLEN (dev);
if (temp < qlen) {
struct urb *urb;
int i;
// don't refill the queue all at once
for (i = 0; i < 10 && dev->rxq.qlen < qlen; i++) {
urb = usb_alloc_urb (0, GFP_ATOMIC);
if (urb != NULL) {
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,14)
urb->transfer_flags |= URB_ASYNC_UNLINK;
#endif
rx_submit (dev, urb, GFP_ATOMIC);
}
}
if (temp != dev->rxq.qlen && netif_msg_link (dev))
devdbg (dev, "rxqlen %d --> %d",
temp, dev->rxq.qlen);
if (dev->rxq.qlen < qlen)
tasklet_schedule (&dev->bh);
}
if (dev->txq.qlen < TX_QLEN (dev))
netif_wake_queue (dev->net);
}
}
/*-------------------------------------------------------------------------
*
* USB Device Driver support
*
*-------------------------------------------------------------------------*/
// precondition: never called in_interrupt
static
void axusbnet_disconnect (struct usb_interface *intf)
{
struct usbnet *dev;
struct usb_device *xdev;
struct net_device *net;
dev = usb_get_intfdata(intf);
usb_set_intfdata(intf, NULL);
if (!dev)
return;
xdev = interface_to_usbdev (intf);
if (netif_msg_probe (dev))
devinfo (dev, "unregister '%s' usb-%s-%s, %s",
intf->dev.driver->name,
xdev->bus->bus_name, xdev->devpath,
dev->driver_info->description);
net = dev->net;
unregister_netdev (net);
/* we don't hold rtnl here ... */
flush_scheduled_work ();
if (dev->driver_info->unbind)
dev->driver_info->unbind (dev, intf);
free_netdev(net);
usb_put_dev (xdev);
}
/*-------------------------------------------------------------------------*/
// precondition: never called in_interrupt
static int
axusbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod)
{
struct usbnet *dev;
struct net_device *net;
struct usb_host_interface *interface;
struct driver_info *info;
struct usb_device *xdev;
int status;
const char *name;
name = udev->dev.driver->name;
info = (struct driver_info *) prod->driver_info;
if (!info) {
printk (KERN_ERR "blacklisted by %s\n", name);
return -ENODEV;
}
xdev = interface_to_usbdev (udev);
interface = udev->cur_altsetting;
usb_get_dev (xdev);
status = -ENOMEM;
// set up our own records
net = alloc_etherdev(sizeof(*dev));
if (!net) {
dbg ("can't kmalloc dev");
goto out;
}
dev = netdev_priv(net);
dev->udev = xdev;
dev->intf = udev;
dev->driver_info = info;
dev->driver_name = name;
dev->msg_enable = netif_msg_init (msg_level, NETIF_MSG_DRV
| NETIF_MSG_PROBE | NETIF_MSG_LINK);
skb_queue_head_init (&dev->rxq);
skb_queue_head_init (&dev->txq);
skb_queue_head_init (&dev->done);
dev->bh.func = axusbnet_bh;
dev->bh.data = (unsigned long) dev;
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,20)
INIT_WORK (&dev->kevent, kevent, dev);
#else
INIT_WORK (&dev->kevent, kevent);
#endif
dev->delay.function = axusbnet_bh;
dev->delay.data = (unsigned long) dev;
init_timer (&dev->delay);
// mutex_init (&dev->phy_mutex);
dev->net = net;
/* rx and tx sides can use different message sizes;
* bind() should set rx_urb_size in that case.
*/
dev->hard_mtu = net->mtu + net->hard_header_len;
#if 0
// dma_supported() is deeply broken on almost all architectures
// possible with some EHCI controllers
if (dma_supported (&udev->dev, DMA_BIT_MASK(64)))
net->features |= NETIF_F_HIGHDMA;
#endif
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)
net->open = axusbnet_open,
net->stop = axusbnet_stop,
net->hard_start_xmit = axusbnet_start_xmit,
net->tx_timeout = axusbnet_tx_timeout,
net->get_stats = axusbnet_get_stats;
#endif
net->watchdog_timeo = TX_TIMEOUT_JIFFIES;
net->ethtool_ops = &axusbnet_ethtool_ops;
// allow device-specific bind/init procedures
// NOTE net->name still not usable ...
status = info->bind (dev, udev);
if (status < 0) {
deverr(dev, "Binding device failed: %d", status);
goto out1;
}
/* maybe the remote can't receive an Ethernet MTU */
if (net->mtu > (dev->hard_mtu - net->hard_header_len))
net->mtu = dev->hard_mtu - net->hard_header_len;
status = init_status (dev, udev);
if (status < 0)
goto out3;
if (!dev->rx_urb_size)
dev->rx_urb_size = dev->hard_mtu;
dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1);
SET_NETDEV_DEV(net, &udev->dev);
status = register_netdev (net);
if (status) {
deverr(dev, "net device registration failed: %d", status);
goto out3;
}
if (netif_msg_probe (dev))
devinfo (dev, "register '%s' at usb-%s-%s, %s, %pM",
udev->dev.driver->name,
xdev->bus->bus_name, xdev->devpath,
dev->driver_info->description,
net->dev_addr);
// ok, it's ready to go.
usb_set_intfdata (udev, dev);
// start as if the link is up
netif_device_attach (net);
return 0;
out3:
if (info->unbind)
info->unbind (dev, udev);
out1:
free_netdev(net);
out:
usb_put_dev(xdev);
return status;
}
/*-------------------------------------------------------------------------*/
/*
* suspend the whole driver as soon as the first interface is suspended
* resume only when the last interface is resumed
*/
static int axusbnet_suspend (struct usb_interface *intf,
#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,10)
pm_message_t message)
#else
u32 message)
#endif
{
struct usbnet *dev = usb_get_intfdata(intf);
if (!dev->suspend_count++) {
/*
* accelerate emptying of the rx and queues, to avoid
* having everything error out.
*/
netif_device_detach (dev->net);
(void) unlink_urbs (dev, &dev->rxq);
(void) unlink_urbs (dev, &dev->txq);
/*
* reattach so runtime management can use and
* wake the device
*/
netif_device_attach (dev->net);
}
return 0;
}
static int
axusbnet_resume (struct usb_interface *intf)
{
struct usbnet *dev = usb_get_intfdata(intf);
if (!--dev->suspend_count)
tasklet_schedule (&dev->bh);
return 0;
}
int
usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod)
{
struct usbnet *dev;
struct net_device *net;
struct usb_host_interface *interface;
struct driver_info *info;
struct usb_device *xdev;
int status;
const char *name;
struct usb_driver *driver = to_usb_driver(udev->dev.driver);
/* usbnet already took usb runtime pm, so have to enable the feature
* for usb interface, otherwise usb_autopm_get_interface may return
* failure if USB_SUSPEND(RUNTIME_PM) is enabled.
*/
if (!driver->supports_autosuspend) {
driver->supports_autosuspend = 1;
pm_runtime_enable(&udev->dev);
}
name = udev->dev.driver->name;
info = (struct driver_info *) prod->driver_info;
if (!info) {
dev_dbg (&udev->dev, "blacklisted by %s\n", name);
return -ENODEV;
}
xdev = interface_to_usbdev (udev);
interface = udev->cur_altsetting;
usb_get_dev (xdev);
status = -ENOMEM;
// set up our own records
net = alloc_etherdev(sizeof(*dev));
if (!net) {
dbg ("can't kmalloc dev");
goto out;
}
/* netdev_printk() needs this so do it as early as possible */
SET_NETDEV_DEV(net, &udev->dev);
dev = netdev_priv(net);
dev->udev = xdev;
dev->intf = udev;
dev->driver_info = info;
dev->driver_name = name;
dev->msg_enable = netif_msg_init (msg_level, NETIF_MSG_DRV
| NETIF_MSG_PROBE | NETIF_MSG_LINK);
skb_queue_head_init (&dev->rxq);
skb_queue_head_init (&dev->txq);
skb_queue_head_init (&dev->done);
skb_queue_head_init(&dev->rxq_pause);
dev->bh.func = usbnet_bh;
dev->bh.data = (unsigned long) dev;
INIT_WORK (&dev->kevent, kevent);
init_usb_anchor(&dev->deferred);
dev->delay.function = usbnet_bh;
dev->delay.data = (unsigned long) dev;
init_timer (&dev->delay);
mutex_init (&dev->phy_mutex);
dev->net = net;
strcpy (net->name, "usb%d");
memcpy (net->dev_addr, node_id, sizeof node_id);
/* rx and tx sides can use different message sizes;
* bind() should set rx_urb_size in that case.
*/
dev->hard_mtu = net->mtu + net->hard_header_len;
#if 0
// dma_supported() is deeply broken on almost all architectures
// possible with some EHCI controllers
if (dma_supported (&udev->dev, DMA_BIT_MASK(64)))
net->features |= NETIF_F_HIGHDMA;
#endif
net->netdev_ops = &usbnet_netdev_ops;
net->watchdog_timeo = TX_TIMEOUT_JIFFIES;
net->ethtool_ops = &usbnet_ethtool_ops;
// allow device-specific bind/init procedures
// NOTE net->name still not usable ...
if (info->bind) {
status = info->bind (dev, udev);
if (status < 0)
goto out1;
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
/* maybe the remote can't receive an Ethernet MTU */
if (net->mtu > (dev->hard_mtu - net->hard_header_len))
net->mtu = dev->hard_mtu - net->hard_header_len;
} else if (!info->in || !info->out)
status = usbnet_get_endpoints (dev, udev);
else {
dev->in = usb_rcvbulkpipe (xdev, info->in);
dev->out = usb_sndbulkpipe (xdev, info->out);
if (!(info->flags & FLAG_NO_SETINT))
status = usb_set_interface (xdev,
interface->desc.bInterfaceNumber,
interface->desc.bAlternateSetting);
else
status = 0;
}
if (status >= 0 && dev->status)
status = init_status (dev, udev);
if (status < 0)
goto out3;
if (!dev->rx_urb_size)
dev->rx_urb_size = dev->hard_mtu;
dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1);
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
SET_NETDEV_DEVTYPE(net, &wlan_type);
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
SET_NETDEV_DEVTYPE(net, &wwan_type);
status = register_netdev (net);
if (status)
goto out3;
netif_info(dev, probe, dev->net,
"register '%s' at usb-%s-%s, %s, %pM\n",
udev->dev.driver->name,
xdev->bus->bus_name, xdev->devpath,
dev->driver_info->description,
net->dev_addr);
// ok, it's ready to go.
usb_set_intfdata (udev, dev);
netif_device_attach (net);
if (dev->driver_info->flags & FLAG_LINK_INTR)
netif_carrier_off(net);
return 0;
out3:
if (info->unbind)
info->unbind (dev, udev);
out1:
free_netdev(net);
out:
usb_put_dev(xdev);
return status;
}
int __devinit rtl_usb_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
int err;
struct ieee80211_hw *hw = NULL;
struct rtl_priv *rtlpriv = NULL;
struct usb_device *udev;
struct rtl_usb_priv *usb_priv;
hw = ieee80211_alloc_hw(sizeof(struct rtl_priv) +
sizeof(struct rtl_usb_priv), &rtl_ops);
if (!hw) {
RT_ASSERT(false, "ieee80211 alloc failed\n");
return -ENOMEM;
}
rtlpriv = hw->priv;
rtlpriv->usb_data = kzalloc(RTL_USB_MAX_RX_COUNT * sizeof(u32),
GFP_KERNEL);
if (!rtlpriv->usb_data)
return -ENOMEM;
/* this spin lock must be initialized early */
spin_lock_init(&rtlpriv->locks.usb_lock);
rtlpriv->usb_data_index = 0;
init_completion(&rtlpriv->firmware_loading_complete);
SET_IEEE80211_DEV(hw, &intf->dev);
udev = interface_to_usbdev(intf);
usb_get_dev(udev);
usb_priv = rtl_usbpriv(hw);
memset(usb_priv, 0, sizeof(*usb_priv));
usb_priv->dev.intf = intf;
usb_priv->dev.udev = udev;
usb_set_intfdata(intf, hw);
/* init cfg & intf_ops */
rtlpriv->rtlhal.interface = INTF_USB;
rtlpriv->cfg = (struct rtl_hal_cfg *)(id->driver_info);
rtlpriv->intf_ops = &rtl_usb_ops;
rtl_dbgp_flag_init(hw);
/* Init IO handler */
_rtl_usb_io_handler_init(&udev->dev, hw);
rtlpriv->cfg->ops->read_chip_version(hw);
/*like read eeprom and so on */
rtlpriv->cfg->ops->read_eeprom_info(hw);
err = _rtl_usb_init(hw);
if (err)
goto error_out;
rtl_usb_init_sw(hw);
/* Init mac80211 sw */
err = rtl_init_core(hw);
if (err) {
RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
"Can't allocate sw for mac80211\n");
goto error_out;
}
if (rtlpriv->cfg->ops->init_sw_vars(hw)) {
RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG, "Can't init_sw_vars\n");
goto error_out;
}
rtlpriv->cfg->ops->init_sw_leds(hw);
return 0;
error_out:
rtl_deinit_core(hw);
_rtl_usb_io_handler_release(hw);
usb_put_dev(udev);
complete(&rtlpriv->firmware_loading_complete);
return -ENODEV;
}
static void pixcir_delete(struct kref *kref)
{
struct pixcir_mt_usb *dev = to_pixcir_dev(kref);
usb_put_dev(dev->udev);
kfree(dev);
}
/*
========================================================================
Routine Description:
Release a use of the usb device structure.
Arguments:
dev - the USB device
Return Value:
None
Note:
========================================================================
*/
void rausb_put_dev(VOID *dev)
{
usb_put_dev((struct usb_device *)dev);
}
/*
Line6 device disconnected.
*/
static void line6_disconnect(struct usb_interface *interface)
{
struct usb_line6 *line6;
struct usb_device *usbdev;
int interface_number;
if (interface == NULL)
return;
usbdev = interface_to_usbdev(interface);
if (usbdev == NULL)
return;
/* removal of additional special files should go here */
sysfs_remove_link(&interface->dev.kobj, "usb_device");
interface_number = interface->cur_altsetting->desc.bInterfaceNumber;
line6 = usb_get_intfdata(interface);
if (line6 != NULL) {
if (line6->urb_listen != NULL)
line6_stop_listen(line6);
if (usbdev != line6->usbdev)
dev_err(line6->ifcdev,
"driver bug: inconsistent usb device\n");
switch (line6->usbdev->descriptor.idProduct) {
case LINE6_DEVID_BASSPODXT:
case LINE6_DEVID_BASSPODXTLIVE:
case LINE6_DEVID_BASSPODXTPRO:
case LINE6_DEVID_POCKETPOD:
case LINE6_DEVID_PODX3:
case LINE6_DEVID_PODX3LIVE:
case LINE6_DEVID_PODXT:
case LINE6_DEVID_PODXTPRO:
line6_pod_disconnect(interface);
break;
case LINE6_DEVID_PODHD300:
case LINE6_DEVID_PODHD500:
line6_podhd_disconnect(interface);
break;
case LINE6_DEVID_PODXTLIVE:
switch (interface_number) {
case PODXTLIVE_INTERFACE_POD:
line6_pod_disconnect(interface);
break;
case PODXTLIVE_INTERFACE_VARIAX:
line6_variax_disconnect(interface);
break;
}
break;
case LINE6_DEVID_VARIAX:
line6_variax_disconnect(interface);
break;
case LINE6_DEVID_PODSTUDIO_GX:
case LINE6_DEVID_PODSTUDIO_UX1:
case LINE6_DEVID_PODSTUDIO_UX2:
case LINE6_DEVID_TONEPORT_GX:
case LINE6_DEVID_TONEPORT_UX1:
case LINE6_DEVID_TONEPORT_UX2:
case LINE6_DEVID_GUITARPORT:
line6_toneport_disconnect(interface);
break;
default:
MISSING_CASE;
}
dev_info(&interface->dev, "Line6 %s now disconnected\n",
line6->properties->name);
}
line6_destruct(interface);
/* decrement reference counters: */
usb_put_intf(interface);
usb_put_dev(usbdev);
}
void rausb_put_dev(struct usb_device *dev)
{
usb_put_dev(dev);
}
static void usbtmc_delete(struct kref *kref)
{
struct usbtmc_device_data *data = to_usbtmc_data(kref);
usb_put_dev(data->usb_dev);
}
static int
ksb_usb_probe(struct usb_interface *ifc, const struct usb_device_id *id)
{
__u8 ifc_num;
struct usb_host_interface *ifc_desc;
struct usb_endpoint_descriptor *ep_desc;
int i;
struct ks_bridge *ksb;
ifc_num = ifc->cur_altsetting->desc.bInterfaceNumber;
switch (id->idProduct) {
case 0x9008:
if (ifc_num != 0)
return -ENODEV;
ksb = __ksb[BOOT_BRIDGE_INDEX];
break;
case 0x9048:
case 0x904C:
if (ifc_num != 2)
return -ENODEV;
ksb = __ksb[EFS_BRIDGE_INDEX];
break;
default:
return -ENODEV;
}
if (!ksb) {
pr_err("ksb is not initialized");
return -ENODEV;
}
ksb->udev = usb_get_dev(interface_to_usbdev(ifc));
ksb->ifc = ifc;
ifc_desc = ifc->cur_altsetting;
for (i = 0; i < ifc_desc->desc.bNumEndpoints; i++) {
ep_desc = &ifc_desc->endpoint[i].desc;
if (!ksb->in_epAddr && usb_endpoint_is_bulk_in(ep_desc))
ksb->in_epAddr = ep_desc->bEndpointAddress;
if (!ksb->out_epAddr && usb_endpoint_is_bulk_out(ep_desc))
ksb->out_epAddr = ep_desc->bEndpointAddress;
}
if (!(ksb->in_epAddr && ksb->out_epAddr)) {
pr_err("could not find bulk in and bulk out endpoints");
usb_put_dev(ksb->udev);
ksb->ifc = NULL;
return -ENODEV;
}
ksb->in_pipe = usb_rcvbulkpipe(ksb->udev, ksb->in_epAddr);
ksb->out_pipe = usb_sndbulkpipe(ksb->udev, ksb->out_epAddr);
usb_set_intfdata(ifc, ksb);
set_bit(USB_DEV_CONNECTED, &ksb->flags);
dbg_log_event(ksb, "PID-ATT", id->idProduct, 0);
ksb->fs_dev = (struct miscdevice *)id->driver_info;
misc_register(ksb->fs_dev);
ifc->needs_remote_wakeup = 1;
usb_enable_autosuspend(ksb->udev);
pr_debug("usb dev connected");
return 0;
}
static int zfLnxProbe(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_device *dev = interface_to_usbdev(interface);
struct net_device *net = NULL;
struct usbdrv_private *macp = NULL;
int vendor_id, product_id;
int result = 0;
usb_get_dev(dev);
vendor_id = dev->descriptor.idVendor;
product_id = dev->descriptor.idProduct;
#ifdef HMAC_DEBUG
printk(KERN_NOTICE "vendor_id = %04x\n", vendor_id);
printk(KERN_NOTICE "product_id = %04x\n", product_id);
if (dev->speed == USB_SPEED_HIGH)
printk(KERN_NOTICE "USB 2.0 Host\n");
else
printk(KERN_NOTICE "USB 1.1 Host\n");
#endif
if (!(macp = kmalloc(sizeof(struct usbdrv_private), GFP_KERNEL)))
{
printk(KERN_ERR "out of memory allocating device structure\n");
result = -ENOMEM;
goto fail;
}
/* Zero the memory */
memset(macp, 0, sizeof(struct usbdrv_private));
net = alloc_etherdev(0);
if (net == NULL)
{
printk(KERN_ERR "zfLnxProbe: Not able to alloc etherdev struct\n");
result = -ENOMEM;
goto fail1;
}
strcpy(net->name, "ath%d");
net->ml_priv = macp; //kernel 2.6
macp->udev = dev;
macp->device = net;
/* set up the endpoint information */
/* check out the endpoints */
macp->interface = interface;
//init_waitqueue_head(&macp->regSet_wait);
//init_waitqueue_head(&macp->iorwRsp_wait);
//init_waitqueue_head(&macp->term_wait);
if (!zfLnxAllocAllUrbs(macp))
{
result = -ENOMEM;
goto fail2;
}
if (!zfLnxInitSetup(net, macp))
{
result = -EIO;
goto fail3;
}
else
{
usb_set_intfdata(interface, macp);
SET_NETDEV_DEV(net, &interface->dev);
if (register_netdev(net) != 0)
{
usb_set_intfdata(interface, NULL);
goto fail3;
}
}
netif_carrier_off(net);
goto done;
fail3:
zfLnxFreeAllUrbs(macp);
fail2:
free_netdev(net); //kernel 2.6
fail1:
kfree(macp);
fail:
usb_put_dev(dev);
macp = NULL;
done:
return result;
}
static
int i1480u_add(struct i1480u *i1480u, struct usb_interface *iface)
{
int result = -ENODEV;
struct wlp *wlp = &i1480u->wlp;
struct usb_device *usb_dev = interface_to_usbdev(iface);
struct net_device *net_dev = i1480u->net_dev;
struct uwb_rc *rc;
struct uwb_dev *uwb_dev;
#ifdef i1480u_FLOW_CONTROL
struct usb_endpoint_descriptor *epd;
#endif
i1480u->usb_dev = usb_get_dev(usb_dev);
i1480u->usb_iface = iface;
rc = uwb_rc_get_by_grandpa(&i1480u->usb_dev->dev);
if (rc == NULL) {
dev_err(&iface->dev, "Cannot get associated UWB Radio "
"Controller\n");
goto out;
}
wlp->xmit_frame = i1480u_xmit_frame;
wlp->fill_device_info = i1480u_fill_device_info;
wlp->stop_queue = i1480u_stop_queue;
wlp->start_queue = i1480u_start_queue;
result = wlp_setup(wlp, rc, net_dev);
if (result < 0) {
dev_err(&iface->dev, "Cannot setup WLP\n");
goto error_wlp_setup;
}
result = 0;
ether_setup(net_dev); /* make it an etherdevice */
uwb_dev = &rc->uwb_dev;
/* FIXME: hookup address change notifications? */
memcpy(net_dev->dev_addr, uwb_dev->mac_addr.data,
sizeof(net_dev->dev_addr));
net_dev->hard_header_len = sizeof(struct untd_hdr_cmp)
+ sizeof(struct wlp_tx_hdr)
+ WLP_DATA_HLEN
+ ETH_HLEN;
net_dev->mtu = 3500;
net_dev->tx_queue_len = 20; /* FIXME: maybe use 1000? */
/* net_dev->flags &= ~IFF_BROADCAST; FIXME: BUG in firmware */
/* FIXME: multicast disabled */
net_dev->flags &= ~IFF_MULTICAST;
net_dev->features &= ~NETIF_F_SG;
net_dev->features &= ~NETIF_F_FRAGLIST;
/* All NETIF_F_*_CSUM disabled */
net_dev->features |= NETIF_F_HIGHDMA;
net_dev->watchdog_timeo = 5*HZ; /* FIXME: a better default? */
net_dev->netdev_ops = &i1480u_netdev_ops;
#ifdef i1480u_FLOW_CONTROL
/* Notification endpoint setup (submitted when we open the device) */
i1480u->notif_urb = usb_alloc_urb(0, GFP_KERNEL);
if (i1480u->notif_urb == NULL) {
dev_err(&iface->dev, "Unable to allocate notification URB\n");
result = -ENOMEM;
goto error_urb_alloc;
}
epd = &iface->cur_altsetting->endpoint[0].desc;
usb_fill_int_urb(i1480u->notif_urb, usb_dev,
usb_rcvintpipe(usb_dev, epd->bEndpointAddress),
i1480u->notif_buffer, sizeof(i1480u->notif_buffer),
i1480u_notif_cb, i1480u, epd->bInterval);
#endif
i1480u->tx_inflight.max = i1480u_TX_INFLIGHT_MAX;
i1480u->tx_inflight.threshold = i1480u_TX_INFLIGHT_THRESHOLD;
i1480u->tx_inflight.restart_ts = jiffies;
usb_set_intfdata(iface, i1480u);
return result;
#ifdef i1480u_FLOW_CONTROL
error_urb_alloc:
#endif
wlp_remove(wlp);
error_wlp_setup:
uwb_rc_put(rc);
out:
usb_put_dev(i1480u->usb_dev);
return result;
}
static void go7007_loader_disconnect(struct usb_interface *interface)
{
dev_info(&interface->dev, "disconnect\n");
usb_put_dev(interface_to_usbdev(interface));
usb_set_intfdata(interface, NULL);
}
/*
========================================================================
Routine Description:
Release allocated resources.
Arguments:
*dev Point to the PCI or USB device
pAd driver control block pointer
Return Value:
None
Note:
========================================================================
*/
static void rt2870_disconnect(struct usb_device *dev, VOID *pAd)
{
struct net_device *net_dev;
DBGPRINT(RT_DEBUG_ERROR, ("rtusb_disconnect: unregister usbnet usb-%s-%s\n",
dev->bus->bus_name, dev->devpath));
if (!pAd)
{
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0) /* kernel 2.4 series */
while(MOD_IN_USE > 0)
{
MOD_DEC_USE_COUNT;
}
#else
usb_put_dev(dev);
#endif /* LINUX_VERSION_CODE */
printk("rtusb_disconnect: pAd == NULL!\n");
return;
}
/* RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST); */
RTMP_DRIVER_NIC_NOT_EXIST_SET(pAd);
/* for debug, wait to show some messages to /proc system */
udelay(1);
RTMP_DRIVER_NET_DEV_GET(pAd, &net_dev);
RtmpPhyNetDevExit(pAd, net_dev);
/* FIXME: Shall we need following delay and flush the schedule?? */
udelay(1);
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0) /* kernel 2.4 series */
#else
flush_scheduled_work();
#endif /* LINUX_VERSION_CODE */
udelay(1);
#ifdef CONFIG_HAS_EARLYSUSPEND
RTMP_DRIVER_ADAPTER_UNREGISTER_EARLYSUSPEND(pAd);
#endif
#ifdef RT_CFG80211_SUPPORT
RTMP_DRIVER_80211_UNREGISTER(pAd, net_dev);
#endif /* RT_CFG80211_SUPPORT */
/* free the root net_device */
// RtmpOSNetDevFree(net_dev);
RtmpRaDevCtrlExit(pAd);
/* free the root net_device */
RtmpOSNetDevFree(net_dev);
/* release a use of the usb device structure */
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0) /* kernel 2.4 series */
while(MOD_IN_USE > 0)
{
MOD_DEC_USE_COUNT;
}
#else
usb_put_dev(dev);
#endif /* LINUX_VERSION_CODE */
udelay(1);
DBGPRINT(RT_DEBUG_ERROR, (" RTUSB disconnect successfully\n"));
}
static int go7007_loader_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_device *usbdev;
const struct firmware *fw;
u16 vendor, product;
const char *fw1, *fw2;
int ret;
int i;
usbdev = usb_get_dev(interface_to_usbdev(interface));
if (!usbdev)
goto failed2;
if (usbdev->descriptor.bNumConfigurations != 1) {
dev_err(&interface->dev, "can't handle multiple config\n");
goto failed2;
}
vendor = le16_to_cpu(usbdev->descriptor.idVendor);
product = le16_to_cpu(usbdev->descriptor.idProduct);
for (i = 0; fw_configs[i].fw_name1; i++)
if (fw_configs[i].vendor == vendor &&
fw_configs[i].product == product)
break;
/* Should never happen */
if (fw_configs[i].fw_name1 == NULL)
goto failed2;
fw1 = fw_configs[i].fw_name1;
fw2 = fw_configs[i].fw_name2;
dev_info(&interface->dev, "loading firmware %s\n", fw1);
if (request_firmware(&fw, fw1, &usbdev->dev)) {
dev_err(&interface->dev,
"unable to load firmware from file \"%s\"\n", fw1);
goto failed2;
}
ret = cypress_load_firmware(usbdev, fw, CYPRESS_FX2);
release_firmware(fw);
if (0 != ret) {
dev_err(&interface->dev, "loader download failed\n");
goto failed2;
}
if (fw2 == NULL)
return 0;
if (request_firmware(&fw, fw2, &usbdev->dev)) {
dev_err(&interface->dev,
"unable to load firmware from file \"%s\"\n", fw2);
goto failed2;
}
ret = cypress_load_firmware(usbdev, fw, CYPRESS_FX2);
release_firmware(fw);
if (0 != ret) {
dev_err(&interface->dev, "firmware download failed\n");
goto failed2;
}
return 0;
failed2:
usb_put_dev(usbdev);
dev_err(&interface->dev, "probe failed\n");
return -ENODEV;
}
/*
* Probe a i2400m interface and register it
*
* @iface: USB interface to link to
* @id: USB class/subclass/protocol id
* @returns: 0 if ok, < 0 errno code on error.
*
* Alloc a net device, initialize the bus-specific details and then
* calls the bus-generic initialization routine. That will register
* the wimax and netdev devices, upload the firmware [using
* _bus_bm_*()], call _bus_dev_start() to finalize the setup of the
* communication with the device and then will start to talk to it to
* finnish setting it up.
*/
static
int i2400mu_probe(struct usb_interface *iface,
const struct usb_device_id *id)
{
int result;
struct net_device *net_dev;
struct device *dev = &iface->dev;
struct i2400m *i2400m;
struct i2400mu *i2400mu;
struct usb_device *usb_dev = interface_to_usbdev(iface);
if (usb_dev->speed != USB_SPEED_HIGH)
dev_err(dev, "device not connected as high speed\n");
/* Allocate instance [calls i2400m_netdev_setup() on it]. */
result = -ENOMEM;
net_dev = alloc_netdev(sizeof(*i2400mu), "wmx%d",
i2400mu_netdev_setup);
if (net_dev == NULL) {
dev_err(dev, "no memory for network device instance\n");
goto error_alloc_netdev;
}
SET_NETDEV_DEV(net_dev, dev);
SET_NETDEV_DEVTYPE(net_dev, &i2400mu_type);
i2400m = net_dev_to_i2400m(net_dev);
i2400mu = container_of(i2400m, struct i2400mu, i2400m);
i2400m->wimax_dev.net_dev = net_dev;
i2400mu->usb_dev = usb_get_dev(usb_dev);
i2400mu->usb_iface = iface;
usb_set_intfdata(iface, i2400mu);
i2400m->bus_tx_block_size = I2400MU_BLK_SIZE;
/*
* Room required in the Tx queue for USB message to accommodate
* a smallest payload while allocating header space is 16 bytes.
* Adding this room for the new tx message increases the
* possibilities of including any payload with size <= 16 bytes.
*/
i2400m->bus_tx_room_min = I2400MU_BLK_SIZE;
i2400m->bus_pl_size_max = I2400MU_PL_SIZE_MAX;
i2400m->bus_setup = NULL;
i2400m->bus_dev_start = i2400mu_bus_dev_start;
i2400m->bus_dev_stop = i2400mu_bus_dev_stop;
i2400m->bus_release = NULL;
i2400m->bus_tx_kick = i2400mu_bus_tx_kick;
i2400m->bus_reset = i2400mu_bus_reset;
i2400m->bus_bm_retries = I2400M_USB_BOOT_RETRIES;
i2400m->bus_bm_cmd_send = i2400mu_bus_bm_cmd_send;
i2400m->bus_bm_wait_for_ack = i2400mu_bus_bm_wait_for_ack;
i2400m->bus_bm_mac_addr_impaired = 0;
switch (id->idProduct) {
case USB_DEVICE_ID_I6050:
case USB_DEVICE_ID_I6050_2:
case USB_DEVICE_ID_I6250:
i2400mu->i6050 = 1;
break;
default:
break;
}
if (i2400mu->i6050) {
i2400m->bus_fw_names = i2400mu_bus_fw_names_6050;
i2400mu->endpoint_cfg.bulk_out = 0;
i2400mu->endpoint_cfg.notification = 3;
i2400mu->endpoint_cfg.reset_cold = 2;
i2400mu->endpoint_cfg.bulk_in = 1;
} else {
i2400m->bus_fw_names = i2400mu_bus_fw_names_5x50;
i2400mu->endpoint_cfg.bulk_out = 0;
i2400mu->endpoint_cfg.notification = 1;
i2400mu->endpoint_cfg.reset_cold = 2;
i2400mu->endpoint_cfg.bulk_in = 3;
}
#ifdef CONFIG_PM
iface->needs_remote_wakeup = 1; /* autosuspend (15s delay) */
device_init_wakeup(dev, 1);
pm_runtime_set_autosuspend_delay(&usb_dev->dev, 15000);
usb_enable_autosuspend(usb_dev);
#endif
result = i2400m_setup(i2400m, I2400M_BRI_MAC_REINIT);
if (result < 0) {
dev_err(dev, "cannot setup device: %d\n", result);
goto error_setup;
}
result = i2400mu_debugfs_add(i2400mu);
if (result < 0) {
dev_err(dev, "Can't register i2400mu's debugfs: %d\n", result);
goto error_debugfs_add;
}
return 0;
error_debugfs_add:
i2400m_release(i2400m);
error_setup:
usb_set_intfdata(iface, NULL);
usb_put_dev(i2400mu->usb_dev);
free_netdev(net_dev);
error_alloc_netdev:
return result;
}
static void smdhsic_disconnect(struct usb_interface *intf)
{
int devid;
struct usb_interface *smd_intf;
struct str_intf_priv *intfpriv;
struct usb_device *device = NULL;
pr_info("%s: Called\n", __func__);
intfpriv = usb_get_intfdata(intf);
if (!intfpriv) {
pr_err("%s: intfpriv is NULL\n", __func__);
goto err_get_intfdata;
}
device = get_usb_device(intfpriv);
devid = GET_DEVID(intfpriv->devid);
pr_debug("%s : devid : %d\n", __func__, devid);
smd_intf = get_usb_intf(intfpriv);
if (!smd_intf) {
pr_err("smd_intf is NULL\n");
goto err_get_usb_intf;
}
if (smd_intf != intf) {
pr_err("smd_intf is not same intf\n");
goto err_mismatched_intf;
}
usb_driver_release_interface(get_usb_driver(intf), smd_intf);
if (!device)
usb_put_dev(device);
switch (devid) {
case FMT_DEV_ID:
pm_runtime_disable(&device->dev);
if (g_usbdev.hsic)
cancel_delayed_work(&g_usbdev.hsic->pm_runtime_work);
smdctl_request_connection_recover(true);
case RAW_DEV_ID:
case RFS_DEV_ID:
case CMD_DEV_ID:
case DOWN_DEV_ID:
if (emu_discon_func[devid])
emu_discon_func[devid](g_usbdev.smd_device[devid]);
else
kfree(intfpriv->data);
break;
default:
pr_warn("%s:Undefined Callback Function\n",
__func__);
}
/* Power on/off kernel-panic workaround,
* if USB suspend cmd was queued in power.work before disconnect,
* reset the runtime PM request value to PM_REQ_NONE
*/
device->dev.power.request = RPM_REQ_NONE;
kfree(intfpriv);
usb_set_intfdata(intf, NULL);
g_usbdev.usbdev = NULL;
g_usbdev.suspended = 0;
g_usbdev.hsic = NULL;
return;
err_mismatched_intf:
err_get_usb_intf:
if (device)
usb_put_dev(device);
err_get_intfdata:
pr_err("release(2) : %p\n", intf);
usb_driver_release_interface(get_usb_driver(intf), intf);
return;
}
static int rmnet_usb_probe(struct usb_interface *iface,
const struct usb_device_id *prod)
{
struct usbnet *unet;
struct driver_info *info = (struct driver_info *)prod->driver_info;
struct usb_device *udev;
int status = 0;
unsigned int i, unet_id, rdev_cnt, n = 0;
bool mux;
udev = interface_to_usbdev(iface);
if (iface->num_altsetting != 1) {
dev_err(&iface->dev, "%s invalid num_altsetting %u\n",
__func__, iface->num_altsetting);
status = -EINVAL;
goto out;
}
mux = test_bit(info->data, &mux_enabled);
rdev_cnt = mux ? no_rmnet_insts_per_dev : 1;
info->in = 0;
for (n = 0; n < rdev_cnt; n++) {
/* Use this filed to increment device count this will be
* used by bind to determin the forward link and reverse
* link network interface names.
*/
info->in++;
status = usbnet_probe(iface, prod);
if (status < 0) {
dev_err(&iface->dev, "usbnet_probe failed %d\n",
status);
goto out;
}
unet_id = n + info->data * no_rmnet_insts_per_dev;
unet_list[unet_id] = unet = usb_get_intfdata(iface);
/*store mux id for later access*/
unet->data[3] = n;
/*save mux info for control and usbnet devices*/
unet->data[1] = unet->data[4] = mux;
/*set rmnet operation mode to eth by default*/
set_bit(RMNET_MODE_LLP_ETH, &unet->data[0]);
/*update net device*/
rmnet_usb_setup(unet->net, mux);
/*create /sys/class/net/rmnet_usbx/dbg_mask*/
status = device_create_file(&unet->net->dev,
&dev_attr_dbg_mask);
if (status) {
free_netdev(unet->net);
usb_put_dev(udev);
goto out;
}
status = rmnet_usb_ctrl_probe(iface, unet->status, info->data,
&unet->data[1]);
if (status) {
device_remove_file(&unet->net->dev, &dev_attr_dbg_mask);
free_netdev(unet->net);
usb_put_dev(udev);
goto out;
}
status = rmnet_usb_data_debugfs_init(unet);
if (status)
dev_dbg(&iface->dev,
"mode debugfs file is not available\n");
}
usb_enable_autosuspend(udev);
if (udev->parent && !udev->parent->parent) {
/* allow modem and roothub to wake up suspended system */
device_set_wakeup_enable(&udev->dev, 1);
device_set_wakeup_enable(&udev->parent->dev, 1);
/* set default autosuspend timeout for modem and roothub */
pm_runtime_set_autosuspend_delay(&udev->dev, 1000);
pm_runtime_set_autosuspend_delay(&udev->parent->dev, 200);
}
return 0;
out:
for (i = 0; i < n; i++) {
unet_id = i + info->data * no_rmnet_insts_per_dev;
rmnet_usb_ctrl_cleanup(
(struct rmnet_ctrl_dev *)unet_list[unet_id]->data[1]);
device_remove_file(&unet_list[unet_id]->net->dev,
&dev_attr_dbg_mask);
free_netdev(unet_list[unet_id]->net);
usb_put_dev(udev);
}
return status;
}
static void tmsi_delete(struct kref *kref) {
struct tmsi_data* dev = container_of(kref, struct tmsi_data, kref);
usb_put_dev(dev->udev);
kfree(dev);
info("Tmsi device deleted");
}
static int mephisto_probe(struct usb_interface *interface, const struct usb_device_id *id)
{
int err = ME_ERRNO_SUCCESS;
mephisto_usb_device_t* dev; /// The usb device.
me_device_t* n_device = NULL;
me_device_t* o_device = NULL;
long unsigned int serial_no;
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,27)
char* tmp;
#endif
PDEBUG("executed.\n");
/// Allocate structures.
dev = kzalloc(sizeof(mephisto_usb_device_t), GFP_KERNEL);
if (!dev)
{
PERROR_CRITICAL("Can't get memory for device's instance.\n");
err = -ENOMEM;
goto ERROR_0;
}
/// Initialize USB lock.
dev->usb_semaphore = kzalloc(sizeof(struct semaphore), GFP_KERNEL);
if (!dev->usb_semaphore)
{
PERROR_CRITICAL("Can't get memory for usb lock.\n");
err = -ENOMEM;
goto ERROR_1;
}
#ifndef init_MUTEX
sema_init(dev->usb_semaphore, 1);
#else
init_MUTEX(dev->usb_semaphore);
#endif
/// Initialize variables.
dev->dev = usb_get_dev(interface_to_usbdev(interface));
if(!dev->dev)
{
PERROR("Error while request for usb device.\n");
err = -ENODEV;
goto ERROR_2;
}
/// Initialize hardware
usb_set_intfdata(interface, dev);
/// Read serial number
#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,25)
tmp = (dev->dev->serial + strlen(dev->dev->serial));
serial_no = simple_strtoul(dev->dev->serial + 2, &tmp, 16);
#else
if (strict_strtoul(dev->dev->serial + 2, 16, &serial_no))
{
serial_no = 0;
}
#endif
dev->serial_no = serial_no;
/// Hardware init
mephisto_endpoints_reset(dev);
/**
Choice:
a) New device connected. Add to device list.
b) Old device reconected. Refresh device structure.
*/
o_device = find_device_on_list(dev, ME_PLUGGED_ANY);
if(o_device)
{
PDEBUG("Old device.\n");
// Old device.
if (o_device->bus.plugged == ME_PLUGGED_IN)
{
// Error device is already on list mark as active!
PERROR("Device is already on list mark as active!\n");
o_device->me_device_disconnect(o_device);
}
}
else
{
PDEBUG("New device.\n");
}
PINFO("CALLING %s constructor\n", "mephisto_constr");
n_device = mephisto_constr(dev, o_device);
if (!n_device)
{
PERROR("Executing '%s()' failed.\n", "mephisto_constr");
err = -ENODEV;
goto ERROR_3;
}
else if (!o_device)
{
PINFO("Adding new entry to device list.\n");
insert_to_device_list(n_device);
}
if (n_device->me_device_postinit)
{
if (n_device->me_device_postinit(n_device, NULL))
{
PERROR("Error while calling me_device_postinit().\n");
/// This error can be ignored.
}
else
{
PDEBUG("me_device_postinit() was sucessful.\n");
}
}
else
{
PERROR("me_device_postinit() not registred!\n");
}
return 0;
ERROR_3:
usb_put_dev(interface_to_usbdev(interface));
ERROR_2:
kfree(dev->usb_semaphore);
ERROR_1:
kfree(dev);
ERROR_0:
return err;
}
static int
bridge_probe(struct usb_interface *iface, const struct usb_device_id *id)
{
struct usb_host_endpoint *endpoint = NULL;
struct usb_host_endpoint *bulk_in = NULL;
struct usb_host_endpoint *bulk_out = NULL;
struct usb_host_endpoint *int_in = NULL;
struct usb_host_endpoint *data_int_in = NULL;
struct usb_device *udev;
int i;
int status = 0;
int numends;
int ch_id;
char **bname = (char **)id->driver_info;
if (iface->num_altsetting != 1) {
pr_err("%s invalid num_altsetting %u\n",
__func__, iface->num_altsetting);
return -EINVAL;
}
udev = interface_to_usbdev(iface);
usb_get_dev(udev);
numends = iface->cur_altsetting->desc.bNumEndpoints;
for (i = 0; i < numends; i++) {
endpoint = iface->cur_altsetting->endpoint + i;
if (!endpoint) {
dev_err(&iface->dev, "%s: invalid endpoint %u\n",
__func__, i);
status = -EINVAL;
goto out;
}
if (usb_endpoint_is_bulk_in(&endpoint->desc))
bulk_in = endpoint;
else if (usb_endpoint_is_bulk_out(&endpoint->desc))
bulk_out = endpoint;
else if (usb_endpoint_is_int_in(&endpoint->desc)) {
if (int_in != 0)
data_int_in = endpoint;
else
int_in = endpoint;
}
}
if (((numends == 3)
&& ((!bulk_in && !data_int_in) || !bulk_out || !int_in))
|| ((numends == 1) && !bulk_in)) {
dev_err(&iface->dev, "%s: invalid endpoints\n", __func__);
status = -EINVAL;
goto out;
}
ch_id = get_bridge_dev_idx();
if (ch_id < 0) {
pr_err("%s all bridge channels claimed. Probe failed\n",
__func__);
return -ENODEV;
}
if (data_int_in) {
__dev[ch_id]->use_int_in_pipe = true;
__dev[ch_id]->period = data_int_in->desc.bInterval;
status = data_bridge_probe(iface, data_int_in, bulk_out,
bname[BRIDGE_DATA_IDX], ch_id);
} else {
status = data_bridge_probe(iface, bulk_in, bulk_out,
bname[BRIDGE_DATA_IDX], ch_id);
}
if (status < 0) {
dev_err(&iface->dev, "data_bridge_probe failed %d\n", status);
goto out;
}
status = ctrl_bridge_probe(iface,
int_in,
bname[BRIDGE_CTRL_IDX],
ch_id);
if (status < 0) {
dev_err(&iface->dev, "ctrl_bridge_probe failed %d\n",
status);
goto error;
}
return 0;
error:
platform_device_unregister(__dev[ch_id]->pdev);
free_rx_urbs(__dev[ch_id]);
usb_set_intfdata(iface, NULL);
out:
usb_put_dev(udev);
return status;
}
static ssize_t usbdev_trig_name_store(struct device *dev,
struct device_attribute *attr,
const char *buf,
size_t size)
{
struct led_classdev *led_cdev = dev_get_drvdata(dev);
struct usbdev_trig_data *td = led_cdev->trigger_data;
if (size < 0 || size >= DEV_BUS_ID_SIZE)
return -EINVAL;
write_lock(&td->lock);
strcpy(td->device_name, buf);
if (size > 0 && td->device_name[size - 1] == '\n')
td->device_name[size - 1] = 0;
if (td->device_name[0] != 0) {
struct usbdev_trig_match match = {
.device_name = td->device_name,
};
/* check for existing device to update from */
usb_for_each_dev(&match, usbdev_trig_find_usb_dev);
if (match.usb_dev) {
if (td->usb_dev)
usb_put_dev(td->usb_dev);
td->usb_dev = match.usb_dev;
td->last_urbnum = atomic_read(&match.usb_dev->urbnum);
}
/* updates LEDs, may start timers */
usbdev_trig_update_state(td);
}
write_unlock(&td->lock);
return size;
}
static DEVICE_ATTR(device_name, 0644, usbdev_trig_name_show,
usbdev_trig_name_store);
static ssize_t usbdev_trig_interval_show(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct led_classdev *led_cdev = dev_get_drvdata(dev);
struct usbdev_trig_data *td = led_cdev->trigger_data;
read_lock(&td->lock);
sprintf(buf, "%u\n", jiffies_to_msecs(td->interval));
read_unlock(&td->lock);
return strlen(buf) + 1;
}
static ssize_t usbdev_trig_interval_store(struct device *dev,
struct device_attribute *attr,
const char *buf,
size_t size)
{
struct led_classdev *led_cdev = dev_get_drvdata(dev);
struct usbdev_trig_data *td = led_cdev->trigger_data;
int ret = -EINVAL;
char *after;
unsigned long value = simple_strtoul(buf, &after, 10);
size_t count = after - buf;
if (*after && isspace(*after))
count++;
if (count == size && value <= 10000) {
write_lock(&td->lock);
td->interval = msecs_to_jiffies(value);
usbdev_trig_update_state(td); /* resets timer */
write_unlock(&td->lock);
ret = count;
}
return ret;
}
static DEVICE_ATTR(activity_interval, 0644, usbdev_trig_interval_show,
usbdev_trig_interval_store);
static int usbdev_trig_notify(struct notifier_block *nb,
unsigned long evt,
void *data)
{
struct usb_device *usb_dev;
struct usbdev_trig_data *td;
if (evt != USB_DEVICE_ADD && evt != USB_DEVICE_REMOVE)
return NOTIFY_DONE;
usb_dev = data;
td = container_of(nb, struct usbdev_trig_data, notifier);
write_lock(&td->lock);
if (strcmp(dev_name(&usb_dev->dev), td->device_name))
goto done;
if (evt == USB_DEVICE_ADD) {
usb_get_dev(usb_dev);
if (td->usb_dev != NULL)
usb_put_dev(td->usb_dev);
td->usb_dev = usb_dev;
td->last_urbnum = atomic_read(&usb_dev->urbnum);
} else if (evt == USB_DEVICE_REMOVE) {
if (td->usb_dev != NULL) {
usb_put_dev(td->usb_dev);
td->usb_dev = NULL;
}
}
usbdev_trig_update_state(td);
done:
write_unlock(&td->lock);
return NOTIFY_DONE;
}
/* here's the real work! */
static void usbdev_trig_timer(unsigned long arg)
{
struct usbdev_trig_data *td = (struct usbdev_trig_data *)arg;
int new_urbnum;
write_lock(&td->lock);
if (!td->usb_dev || td->interval == 0) {
/*
* we don't need to do timer work, just reflect device presence
*/
if (td->usb_dev)
led_set_brightness(td->led_cdev, LED_FULL);
else
led_set_brightness(td->led_cdev, LED_OFF);
goto no_restart;
}
if (td->interval)
new_urbnum = atomic_read(&td->usb_dev->urbnum);
else
new_urbnum = 0;
if (td->usb_dev) {
/*
* Base state is ON (device is present). If there's no device,
* we don't get this far and the LED is off.
* OFF -> ON always
* ON -> OFF on activity
*/
if (td->led_cdev->brightness == LED_OFF)
led_set_brightness(td->led_cdev, LED_FULL);
else if (td->last_urbnum != new_urbnum)
led_set_brightness(td->led_cdev, LED_OFF);
} else {
/*
* base state is OFF
* ON -> OFF always
* OFF -> ON on activity
*/
if (td->led_cdev->brightness == LED_FULL)
led_set_brightness(td->led_cdev, LED_OFF);
else if (td->last_urbnum != new_urbnum)
led_set_brightness(td->led_cdev, LED_FULL);
}
td->last_urbnum = new_urbnum;
mod_timer(&td->timer, jiffies + td->interval);
no_restart:
write_unlock(&td->lock);
}
static void usbdev_trig_activate(struct led_classdev *led_cdev)
{
struct usbdev_trig_data *td;
int rc;
td = kzalloc(sizeof(struct usbdev_trig_data), GFP_KERNEL);
if (!td)
return;
rwlock_init(&td->lock);
td->notifier.notifier_call = usbdev_trig_notify;
td->notifier.priority = 10;
setup_timer(&td->timer, usbdev_trig_timer, (unsigned long) td);
td->led_cdev = led_cdev;
td->interval = msecs_to_jiffies(50);
led_cdev->trigger_data = td;
rc = device_create_file(led_cdev->dev, &dev_attr_device_name);
if (rc)
goto err_out;
rc = device_create_file(led_cdev->dev, &dev_attr_activity_interval);
if (rc)
goto err_out_device_name;
usb_register_notify(&td->notifier);
return;
err_out_device_name:
device_remove_file(led_cdev->dev, &dev_attr_device_name);
err_out:
led_cdev->trigger_data = NULL;
kfree(td);
}
static void usbdev_trig_deactivate(struct led_classdev *led_cdev)
{
struct usbdev_trig_data *td = led_cdev->trigger_data;
if (td) {
usb_unregister_notify(&td->notifier);
device_remove_file(led_cdev->dev, &dev_attr_device_name);
device_remove_file(led_cdev->dev, &dev_attr_activity_interval);
write_lock(&td->lock);
if (td->usb_dev) {
usb_put_dev(td->usb_dev);
td->usb_dev = NULL;
}
write_unlock(&td->lock);
del_timer_sync(&td->timer);
kfree(td);
}
}
static struct led_trigger usbdev_led_trigger = {
.name = "usbdev",
.activate = usbdev_trig_activate,
.deactivate = usbdev_trig_deactivate,
};
static int __init usbdev_trig_init(void)
{
return led_trigger_register(&usbdev_led_trigger);
}
static void __exit usbdev_trig_exit(void)
{
led_trigger_unregister(&usbdev_led_trigger);
}
module_init(usbdev_trig_init);
module_exit(usbdev_trig_exit);
MODULE_AUTHOR("Gabor Juhos <*****@*****.**>");
MODULE_DESCRIPTION("USB device LED trigger");
MODULE_LICENSE("GPL v2");
static int __devinit
bridge_probe(struct usb_interface *iface, const struct usb_device_id *id)
{
struct usb_host_endpoint *endpoint = NULL;
struct usb_host_endpoint *bulk_in = NULL;
struct usb_host_endpoint *bulk_out = NULL;
struct usb_host_endpoint *int_in = NULL;
struct usb_device *udev;
int i;
int status = 0;
int numends;
int ch_id;
char **bname = (char **)id->driver_info;
if (iface->num_altsetting != 1) {
err("%s invalid num_altsetting %u\n",
__func__, iface->num_altsetting);
return -EINVAL;
}
udev = interface_to_usbdev(iface);
usb_get_dev(udev);
numends = iface->cur_altsetting->desc.bNumEndpoints;
for (i = 0; i < numends; i++) {
endpoint = iface->cur_altsetting->endpoint + i;
if (!endpoint) {
dev_err(&iface->dev, "%s: invalid endpoint %u\n",
__func__, i);
status = -EINVAL;
goto out;
}
if (usb_endpoint_is_bulk_in(&endpoint->desc))
bulk_in = endpoint;
else if (usb_endpoint_is_bulk_out(&endpoint->desc))
bulk_out = endpoint;
else if (usb_endpoint_is_int_in(&endpoint->desc))
int_in = endpoint;
}
if (!bulk_in || !bulk_out || !int_in) {
dev_err(&iface->dev, "%s: invalid endpoints\n", __func__);
status = -EINVAL;
goto out;
}
ch_id = get_bridge_dev_idx();
if (ch_id < 0) {
err("%s all bridge channels claimed. Probe failed\n", __func__);
return -ENODEV;
}
status = data_bridge_probe(iface, bulk_in, bulk_out,
bname[BRIDGE_DATA_IDX], ch_id);
if (status < 0) {
dev_err(&iface->dev, "data_bridge_probe failed %d\n", status);
goto out;
}
status = ctrl_bridge_probe(iface, int_in, bname[BRIDGE_CTRL_IDX],
ch_id);
if (status < 0) {
dev_err(&iface->dev, "ctrl_bridge_probe failed %d\n", status);
goto error;
}
// ASUS_BSP+++ Wenli "tty device for AT command"
#ifndef DISABLE_ASUS_DUN
pr_info("%s: bridge probe success\n", __func__);
if (ch_id == DUN_DATA_ID) {
is_open_asus = false;
is_open_usb = false;
gdun_tty = NULL;
ctrl_bridge_init_asus();
s_is_bridge_init = true;
pr_info("%s: gdun connect\n", __func__);
}
#endif
// ASUS_BSP--- Wenli "tty device for AT command"
return 0;
error:
platform_device_unregister(__dev[ch_id]->pdev);
free_rx_urbs(__dev[ch_id]);
usb_set_intfdata(iface, NULL);
out:
usb_put_dev(udev);
return status;
}
static void ath6kl_usb_remove(struct usb_interface *interface)
{
usb_put_dev(interface_to_usbdev(interface));
ath6kl_usb_device_detached(interface);
}
static int asus_oled_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_device *udev = interface_to_usbdev(interface);
struct asus_oled_dev *odev = NULL;
int retval = -ENOMEM;
uint16_t dev_width = 0;
enum oled_pack_mode pack_mode = PACK_MODE_LAST;
const struct oled_dev_desc_str *dev_desc = oled_dev_desc_table;
const char *desc = NULL;
if (!id) {
/* Even possible? Just to make sure...*/
dev_err(&interface->dev, "No usb_device_id provided!\n");
return -ENODEV;
}
for (; dev_desc->idVendor; dev_desc++) {
if (dev_desc->idVendor == id->idVendor
&& dev_desc->idProduct == id->idProduct) {
dev_width = dev_desc->devWidth;
desc = dev_desc->devDesc;
pack_mode = dev_desc->packMode;
break;
}
}
if (!desc || dev_width < 1 || pack_mode == PACK_MODE_LAST) {
dev_err(&interface->dev,
"Missing or incomplete device description!\n");
return -ENODEV;
}
odev = kzalloc(sizeof(struct asus_oled_dev), GFP_KERNEL);
if (odev == NULL) {
dev_err(&interface->dev, "Out of memory\n");
return -ENOMEM;
}
odev->udev = usb_get_dev(udev);
odev->pic_mode = ASUS_OLED_STATIC;
odev->dev_width = dev_width;
odev->pack_mode = pack_mode;
odev->height = 0;
odev->width = 0;
odev->x_shift = 0;
odev->y_shift = 0;
odev->buf_offs = 0;
odev->buf_size = 0;
odev->last_val = 0;
odev->buf = NULL;
odev->enabled = 1;
odev->dev = NULL;
usb_set_intfdata(interface, odev);
retval = device_create_file(&interface->dev,
&ASUS_OLED_DEVICE_ATTR(enabled));
if (retval)
goto err_files;
retval = device_create_file(&interface->dev,
&ASUS_OLED_DEVICE_ATTR(picture));
if (retval)
goto err_files;
odev->dev = device_create(oled_class, &interface->dev, MKDEV(0, 0),
NULL, "oled_%d", ++oled_num);
if (IS_ERR(odev->dev)) {
retval = PTR_ERR(odev->dev);
goto err_files;
}
dev_set_drvdata(odev->dev, odev);
retval = device_create_file(odev->dev, &dev_attr_enabled);
if (retval)
goto err_class_enabled;
retval = device_create_file(odev->dev, &dev_attr_picture);
if (retval)
goto err_class_picture;
dev_info(&interface->dev,
"Attached Asus OLED device: %s [width %u, pack_mode %d]\n",
desc, odev->dev_width, odev->pack_mode);
if (start_off)
enable_oled(odev, 0);
return 0;
err_class_picture:
device_remove_file(odev->dev, &dev_attr_picture);
err_class_enabled:
device_remove_file(odev->dev, &dev_attr_enabled);
device_unregister(odev->dev);
err_files:
device_remove_file(&interface->dev, &ASUS_OLED_DEVICE_ATTR(enabled));
device_remove_file(&interface->dev, &ASUS_OLED_DEVICE_ATTR(picture));
usb_set_intfdata(interface, NULL);
usb_put_dev(odev->udev);
kfree(odev);
return retval;
}
static int __devinit p54u_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
struct usb_device *udev = interface_to_usbdev(intf);
struct ieee80211_hw *dev;
struct p54u_priv *priv;
int err;
unsigned int i, recognized_pipes;
DECLARE_MAC_BUF(mac);
dev = p54_init_common(sizeof(*priv));
if (!dev) {
printk(KERN_ERR "prism54usb: ieee80211 alloc failed\n");
return -ENOMEM;
}
priv = dev->priv;
SET_IEEE80211_DEV(dev, &intf->dev);
usb_set_intfdata(intf, dev);
priv->udev = udev;
usb_get_dev(udev);
/* really lazy and simple way of figuring out if we're a 3887 */
/* TODO: should just stick the identification in the device table */
i = intf->altsetting->desc.bNumEndpoints;
recognized_pipes = 0;
while (i--) {
switch (intf->altsetting->endpoint[i].desc.bEndpointAddress) {
case P54U_PIPE_DATA:
case P54U_PIPE_MGMT:
case P54U_PIPE_BRG:
case P54U_PIPE_DEV:
case P54U_PIPE_DATA | USB_DIR_IN:
case P54U_PIPE_MGMT | USB_DIR_IN:
case P54U_PIPE_BRG | USB_DIR_IN:
case P54U_PIPE_DEV | USB_DIR_IN:
case P54U_PIPE_INT | USB_DIR_IN:
recognized_pipes++;
}
}
priv->common.open = p54u_open;
if (recognized_pipes < P54U_PIPE_NUMBER) {
priv->hw_type = P54U_3887;
priv->common.tx = p54u_tx_3887;
} else {
dev->extra_tx_headroom += sizeof(struct net2280_tx_hdr);
priv->common.tx_hdr_len = sizeof(struct net2280_tx_hdr);
priv->common.tx = p54u_tx_net2280;
}
priv->common.stop = p54u_stop;
if (priv->hw_type)
err = p54u_upload_firmware_3887(dev);
else
err = p54u_upload_firmware_net2280(dev);
if (err)
goto err_free_dev;
err = p54u_read_eeprom(dev);
if (err)
goto err_free_dev;
if (!is_valid_ether_addr(dev->wiphy->perm_addr)) {
u8 perm_addr[ETH_ALEN];
printk(KERN_WARNING "prism54usb: Invalid hwaddr! Using randomly generated MAC addr\n");
random_ether_addr(perm_addr);
SET_IEEE80211_PERM_ADDR(dev, perm_addr);
}
skb_queue_head_init(&priv->rx_queue);
err = ieee80211_register_hw(dev);
if (err) {
printk(KERN_ERR "prism54usb: Cannot register netdevice\n");
goto err_free_dev;
}
printk(KERN_INFO "%s: hwaddr %s, isl38%02x\n",
wiphy_name(dev->wiphy),
print_mac(mac, dev->wiphy->perm_addr),
priv->common.version);
return 0;
err_free_dev:
ieee80211_free_hw(dev);
usb_set_intfdata(intf, NULL);
usb_put_dev(udev);
return err;
}
static int prism2sta_probe_usb(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_device *dev;
wlandevice_t *wlandev = NULL;
hfa384x_t *hw = NULL;
int result = 0;
dev = interface_to_usbdev(interface);
wlandev = create_wlan();
if (!wlandev) {
dev_err(&interface->dev, "Memory allocation failure.\n");
result = -EIO;
goto failed;
}
hw = wlandev->priv;
if (wlan_setup(wlandev, &(interface->dev)) != 0) {
dev_err(&interface->dev, "wlan_setup() failed.\n");
result = -EIO;
goto failed;
}
/* Initialize the hw data */
hfa384x_create(hw, dev);
hw->wlandev = wlandev;
/* Register the wlandev, this gets us a name and registers the
* linux netdevice.
*/
SET_NETDEV_DEV(wlandev->netdev, &(interface->dev));
/* Do a chip-level reset on the MAC */
if (prism2_doreset) {
result = hfa384x_corereset(hw,
prism2_reset_holdtime,
prism2_reset_settletime, 0);
if (result != 0) {
result = -EIO;
dev_err(&interface->dev,
"hfa384x_corereset() failed.\n");
goto failed_reset;
}
}
usb_get_dev(dev);
wlandev->msdstate = WLAN_MSD_HWPRESENT;
/* Try and load firmware, then enable card before we register */
prism2_fwtry(dev, wlandev);
prism2sta_ifstate(wlandev, P80211ENUM_ifstate_enable);
if (register_wlandev(wlandev) != 0) {
dev_err(&interface->dev, "register_wlandev() failed.\n");
result = -EIO;
goto failed_register;
}
goto done;
failed_register:
usb_put_dev(dev);
failed_reset:
wlan_unsetup(wlandev);
failed:
kfree(wlandev);
kfree(hw);
wlandev = NULL;
done:
usb_set_intfdata(interface, wlandev);
return result;
}
