The CuraEngine is a C++ console application for 3D printing GCode generation. It has been made as a better and faster alternative to the old Skeinforge engine.

The CuraEngine is pure C++ and uses Clipper from http://www.angusj.com/delphi/clipper.php There are no external dependences and Clipper is included in the source code without modifications.

This is just a console application for GCode generation. For a full graphical application look at https://github.com/daid/Cura with is the graphical frontend for CuraEngine.

The CuraEngine can be used seperately or in other applications. Feel free to add it to your application. But to take note of the License.

CuraEngine is released under terms of the AGPLv3 License. Terms of the license can be found in the LICENSE file. Or at http://www.gnu.org/licenses/agpl.html

But in general it boils down to: You need to share the source of any CuraEngine modifications if you make an application with the CuraEngine. (Even if you make a web-based slicer, you still need to share the source!)

The Cura Engine is structured as mainly .h files. This is not standard for an C++ project. However, using less cpp files makes the optimizer work harder and removes linking error issues. It's partialy a result of lazyness but also for optimalizations.

The .h files contain different steps called from the main.cpp file. The main.cpp file contains the global slicing logic.

The slicing process follows the following global steps:

• Load 3D model
• Analize and fix 3D model
• Slice 3D model into 2D layers
• Build LayerParts from sliced layers
• Generate Insets
• Generate up/down skins areas
• Generate sparse infill areas
• Generate GCode for each layer

Each step has more logic in it. But this is a general overview. All data for the engine is stored in the "SliceDataStorage". It's important to remember that only the data from the previous step is valid.

Coordinates are stored in 64bit integers as microns in the code. So if you see a value of 1000 then this mean 1mm of distance. This is because Clipper works on 64bit integers and microns give a high enough resolution without limiting the size too much. Note that there are some bits and pieces of code that need to be careful about 64bit overflows, especially calculating lengths sqrt(xx+yy) can cause overflows.

The OptimizedModel is a 3D model stored with vertex<->face relations. This gives touching face relations which are used later on to slice into layers faster.

While usually the whole GCode generation process is called Slicing. The slicer in the CuraEngine is the piece of code that generates layers. Each layer has closed 2D polygons. These polygons are generated in a 2 step process. First all triangles are cut into lines per layer, for each layer a "line segment" is added to that layer. Next all these line-segments are connected to eachother to make Polygons. The vertex<->face relations of the OptimizedModel help to make this process fast, as there is a huge chance that 2 connecting faces also make 2 connecting line-segments. This code also fixes up small holes in the 3D model, so your model doesn't need to be perfect Manifold. It also accounts for incorrect normals, so it can flip around line-segments to fit end-to-end.

After the Slicer we have closed Polygons which can be used in Clipper, as Clipper can only opperate on closed 2D polygons.

An important concept to grasp is the LayerParts. LayerParts are seperate parts inside a single layer. For example, if you have a cube. Then each layer has a single LayerPart. However, if you have a table, then the layers which build the legs have a LayerPart per leg, and thus there will be 4 LayerParts. A LayerPart is a seperated area inside a single layer which does not touch any other LayerParts. Most operations run on LayerParts as it reduces the amount of data to process. During GCode generation handling each LayerPart as an own step makes sure you never travel between LayerParts and thus reducing the amount of external travel. LayerParts are generated after the Slicer step.

To generate the LayerParts Clipper is used. A Clipper union with extended results gives a list of Polygons with holes in them. Each polygon is a LayerPart, and the holes are added to this LayerPart.

Insets are also called "Perimeters" or "Loops" sometimes. Generating the insets is only a small bit of code, as Clipper does most of the heavy lifting.

The skin code generates the fully filled areas, it does this with some heavy boolean Clipper action. The skin step uses data from different layers to get the job done. Check the code for details. The sparse infill area code is almost the same as the skin code. With the difference that it keeps the other areas and uses different offsets.

Note that these steps generate the areas, not the actual infill lines. The infill line paths are generated later on. So the result of this step are list of Polygons which are the areas that need to be filled.

The GCode generation is quite a large bit of code. As a lot is going on here. Important bits here are:

• PathOrderOptimizer: This piece of code needs to solve a TravelingSalesmanProblem. Given a list of polygons/lines it tries to find the best order in which to print them. It currently does this by finding the closest next polygon to print.
• Infill: This code generates a group of lines from an area. This is the code that generates the actuall infill pattern. There is also a concentric infill function, which is currently not used.
• Comb: The combing code is the code that tries to avoid holes when moving around the head without printing. This code also detects when it fails. The final GCode generator uses the combing code while generating the final GCode. So they interact closely.
• GCodeExport: The GCode export is a 2 step process. First it collects all the paths for a layer that it needs to print, this includes all moves, prints, extrusion widths. And then it generates the final GCode. This is the only piece of code that has knowledge about GCode, and to generate a different flavor of GCode it will be the only piece that needs adjustment. All volumatric calculations also happen here.