void StopMode(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Disable all GPIOs to reduce power */
MX_GPIO_Deinit();
/* Configure User push-button as external interrupt generator */
__HAL_RCC_GPIOC_CLK_ENABLE();
GPIO_InitStruct.Pin = B1_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(B1_GPIO_Port, &GPIO_InitStruct);
HAL_UART_DeInit(&huart2);
/* Suspend Tick increment to prevent wakeup by Systick interrupt.
Otherwise the Systick interrupt will wake up the device within 1ms (HAL time base) */
HAL_SuspendTick();
/* We enable again the PWR peripheral */
__HAL_RCC_PWR_CLK_ENABLE();
/* Request to enter SLEEP mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_SLEEPENTRY_WFI);
/* Resume Tick interrupt if disabled prior to sleep mode entry*/
HAL_ResumeTick();
/* Reinitialize GPIOs */
MX_GPIO_Init();
/* Reinitialize UART2 */
MX_USART2_UART_Init();
}
void
stopmode_entry()
{
extern xSemaphoreHandle semaphore_puts;
xSemaphoreTake(semaphore_puts, portMAX_DELAY);
puts("modem power off\n\r");
puts("cpu enter stop mode\n\r");
xSemaphoreGive(semaphore_puts);
modem_power(0);
stopmode_gpio_configuration();
vTaskSuspendAll();
watchdogtimer_stop();
rtc_backup_write(19, SYSRESET_STOP_MODE);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* STOP here until EXTI interrupt */
NVIC_SystemReset();
while(1){
vTaskDelay(1000);
}
}
/**
* @brief Enter in stop mode and exit by pressingf the tamper button
* @param None
* @note This example enter in stop mode.
* @retval None
*/
void LowPowerStopEXTI(void)
{
kWindow_Popup("STOP EXTI", LCD_COLOR_WHITE, LCD_COLOR_BLUE, \
"\n\nPres JOY sel to\nstart\nstop mode\n", \
LCD_COLOR_WHITE, LCD_COLOR_BLUE );
HAL_Delay(100);
user_event = JOY_UP;
while(user_event != JOY_SEL)
{
user_action = 0;
};
kWindow_Popup("STOP EXTI", LCD_COLOR_WHITE, LCD_COLOR_BLUE, \
"\n\nstop mode\nstarted\npress tamper\nto exit\n", \
LCD_COLOR_BLUE, LCD_COLOR_WHITE );
/* User push-button (EXTI_Line0) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_EXTI);
/* avoid wakeup from JOY event */
BSP_JOY_Init(JOY_MODE_GPIO);
/* Clear PWR wake up Flag */
__HAL_PWR_CLEAR_FLAG(PWR_FLAG_WU);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Restore the clock configuration */
SystemClock_STOPExit();
/* User push-button (EXTI_Line0) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_GPIO);
BSP_JOY_Init(JOY_MODE_EXTI);
}
STATIC mp_obj_t machine_sleep(void) {
// takes longer to wake but reduces stop current
HAL_PWREx_EnableFlashPowerDown();
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
// reconfigure the system clock after waking up
// enable HSE
__HAL_RCC_HSE_CONFIG(RCC_HSE_ON);
while (!__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY)) {
}
// enable PLL
__HAL_RCC_PLL_ENABLE();
while (!__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY)) {
}
// select PLL as system clock source
MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_SYSCLKSOURCE_PLLCLK);
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) {
}
return mp_const_none;
}
/**
* @brief Enter in stop mode and exit by an alarm
* @param None
* @note This example enter in stop mode.
* @retval None
*/
void LowPowerStopRTCAlarm(void)
{
kWindow_Popup("STOP Alarme", LCD_COLOR_WHITE, LCD_COLOR_BLUE,\
"\nset delay time\n", \
LCD_COLOR_BLUE, LCD_COLOR_WHITE );
/* set the alarm */
LowPowerHandleAlarm();
kWindow_Popup("STOP Alarm", LCD_COLOR_WHITE, LCD_COLOR_BLUE, \
"\n\nstop mode\nstarted\nwait alarm\nto exit\n", \
LCD_COLOR_BLUE, LCD_COLOR_WHITE );
BSP_JOY_Init(JOY_MODE_GPIO);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFE);
/* Restore the clock configuration */
SystemClock_STOPExit();
HAL_RTC_DeactivateAlarm(&RtcHandle, RTC_ALARM_A);
/* Clear the Alarm interrupt pending bit */
__HAL_RTC_ALARM_CLEAR_FLAG(&RtcHandle,RTC_FLAG_ALRAF);
/* Clear the EXTI's line Flag for RTC Alarm */
__HAL_RTC_EXTI_CLEAR_FLAG(RTC_EXTI_LINE_ALARM_EVENT);
BSP_JOY_Init(JOY_MODE_EXTI);
}
/**
* @brief Prepare the system to enter STOP mode.
* @param None
* @retval None
*/
static void StopSequence_Config(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* PWR Peripheral clock enable */
__HAL_RCC_PWR_CLK_ENABLE();
/* Enable GPIOs clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOD_CLK_ENABLE();
__HAL_RCC_GPIOE_CLK_ENABLE();
__HAL_RCC_GPIOF_CLK_ENABLE();
/* Configure all GPIO port pins in Analog mode */
GPIO_InitStruct.Pin = GPIO_PIN_All;
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/* Request to enter STOP mode with regulator in low power */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
EnterInStopMode = 1;
}
void DEVICE_Handler(void)
{
char buf[10];
static uint8_t _start = 1;
// device.door->NEW = 1;
while (1)
{
if (sleep)
{
// HAL_PCD_DevDisconnect(&hpcd_USB_FS);
/* отключить SysTick */
HAL_SuspendTick();
/* Enters Stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* выход из STOPMode и инициализация USB */
/* включить SysTick */
HAL_ResumeTick();
/* Configure the system clock */
SystemClock_Config();
// HAL_PCD_DevConnect(&hpcd_USB_FS);
}
else
{
// HAL_Delay(200);
// printf("test\n");
// HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_15);
}
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* STM32L0xx HAL library initialization:
- Configure the Flash prefetch, Flash preread and Buffer caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 2 MHz */
SystemClock_Config();
while (1)
{
/* Configure LED3 */
BSP_LED_Init(LED3);
/* Turn LED3 on */
BSP_LED_On(LED3);
/* Insert 5 second delay */
HAL_Delay(5000);
/* Turn LED3 OFF */
BSP_LED_Off(LED3);
/* Configure the system Power */
SystemPower_Config();
/* Configure PA.12 (Arduino D2) as input with External interrupt */
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
/* Enable GPIOA clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Enable and set PA.12 (Arduino D2) EXTI Interrupt to the lowest priority */
NVIC_SetPriority((IRQn_Type)(EXTI4_15_IRQn), 0x03);
HAL_NVIC_EnableIRQ((IRQn_Type)(EXTI4_15_IRQn));
/* Enable Power Control clock */
__HAL_RCC_PWR_CLK_ENABLE();
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP */
SystemClock_Config();
}
}
void deepsleep(void)
{
// Request to enter STOP mode with regulator in low power mode
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
// After wake-up from STOP reconfigure the PLL
SetSysClock();
}
/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSE/LSI
* =====================================
* - RTC Clocked by LSE or LSI
* - Regulator in LP mode
* - HSI, HSE OFF and LSI OFF if not used as RTC Clock source
* - No IWDG
* - Wakeup using EXTI Line (User push-button PC.13)
* @param None
* @retval None
*/
void StopMode_Measure(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Warning : Reconfiguring all GPIO will close the connexion with the debugger */
/* Enable GPIOs clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOD_CLK_ENABLE();
__HAL_RCC_GPIOF_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pin = GPIO_PIN_All;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/* Disable GPIOs clock */
__HAL_RCC_GPIOA_CLK_DISABLE();
__HAL_RCC_GPIOB_CLK_DISABLE();
__HAL_RCC_GPIOC_CLK_DISABLE();
__HAL_RCC_GPIOD_CLK_DISABLE();
__HAL_RCC_GPIOF_CLK_DISABLE();
/* Configure User Button */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP: enable HSI and PLL with HSI as source*/
SYSCLKConfig_STOP();
/* Initialize LED2 on the board */
BSP_LED_Init(LED2);
/* Turn LED2 On */
BSP_LED_On(LED2);
/* Inserted Delay */
HAL_Delay(200);
}
void MCU_Enter_StopMode(void)
{
HAL_SuspendTick();
__HAL_PWR_CLEAR_FLAG(PWR_FLAG_WU);
while((PWR->CSR & (uint32_t) 0x00000001)!=0);//attesa che il WUF si azzeri (via HW)
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFE); /* Infinite loop */
HAL_ResumeTick();
}
void deepsleep(void)
{
// Request to enter STOP mode with regulator in low power mode
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
// After wake-up from STOP need to reconfigure the system clock
SetSysClock();
#if DEVICE_LOWPOWERTIMER
rtc_synchronize();
#endif
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32L0xx HAL library initialization:
- Configure the Flash prefetch, Flash preread and Buffer caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 to handle error handler */
BSP_LED_Init(LED2);
/* Configure the system clock @ 32 Mhz */
SystemClock_Config();
/* Configure the system Power */
SystemPower_Config();
while (1)
{
/* Insert 5 seconds delay */
HAL_Delay(5000);
/* Disable Wakeup Counter */
HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle);
/*## Setting the Wake up time ############################################*/
/* RTC Wakeup Interrupt Generation:
Wakeup Time Base = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI))
Wakeup Time = Wakeup Time Base * WakeUpCounter
= (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI)) * WakeUpCounter
==> WakeUpCounter = Wakeup Time / Wakeup Time Base
To configure the wake up timer to 4s the WakeUpCounter is set to 0x1FFF:
RTC_WAKEUPCLOCK_RTCCLK_DIV = RTCCLK_Div16 = 16
Wakeup Time Base = 16 /(~39.000KHz) = ~0,410 ms
Wakeup Time = ~4s = 0,410ms * WakeUpCounter
==> WakeUpCounter = ~4s/0,410ms = 9750 = 0x2616 */
HAL_RTCEx_SetWakeUpTimer_IT(&RTCHandle, 0x2616, RTC_WAKEUPCLOCK_RTCCLK_DIV16);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP: enable HSI, PLL and select
PLL as system clock source (HSI and PLL are disabled automatically in STOP mode) */
SystemClockConfig_STOP();
}
}
void RtcEnterLowPowerStopMode( void )
{
if( ( LowPowerDisableDuringTask == false ) && ( RtcTimerEventAllowsLowPower == true ) )
{
// Disable IRQ while the MCU is being deinitialized to prevent race issues
__disable_irq( );
HAL_MspDeInit();
__enable_irq( );
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
}
}
void deepsleep(void)
{
// Disable HAL tick interrupt
TimMasterHandle.Instance = TIM5;
__HAL_TIM_DISABLE_IT(&TimMasterHandle, TIM_IT_CC2);
// Request to enter STOP mode with regulator in low power mode
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
// After wake-up from STOP reconfigure the PLL
SetSysClock();
// Enable HAL tick interrupt
__HAL_TIM_ENABLE_IT(&TimMasterHandle, TIM_IT_CC2);
}
/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSE/LSI
* =====================================
* - RTC Clocked by LSE or LSI
* - Regulator in LP mode
* - HSI, HSE OFF and LSI OFF if not used as RTC Clock source
* - No IWDG
* - FLASH in deep power down mode
* - Automatic Wakeup using RTC clocked by LSE/LSI (~20s)
* @param None
* @retval None
*/
void StopMode_Measure(void)
{
#ifdef STOP_IO
GPIO_InitTypeDef GPIO_InitStruct;
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOH_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pin = GPIO_PIN_All;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* Disable GPIOs clock */
__HAL_RCC_GPIOA_CLK_DISABLE();
__HAL_RCC_GPIOB_CLK_DISABLE();
__HAL_RCC_GPIOC_CLK_DISABLE();
__HAL_RCC_GPIOH_CLK_DISABLE();
#endif
/* FLASH Deep Power Down Mode enabled */
HAL_PWREx_EnableFlashPowerDown();
/*## Enter Stop Mode #######################################################*/
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFE);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SYSCLKConfig_STOP();
/* Disable Wake-up timer */
if(HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization: global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/* Configure LED3 */
BSP_LED_Init(LED3);
while (1)
{
/* Configure LED1 */
BSP_LED_Init(LED1);
/* Turn LED1 on */
BSP_LED_On(LED1);
/* Insert 5 second delay */
HAL_Delay(5000);
/* Turn LED1 OFF */
BSP_LED_Off(LED1);
/* Tamper push-button (lines 15 to 10) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_TAMPER, BUTTON_MODE_EXTI);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP */
SystemClock_Config();
}
}
void RtcEnterLowPowerStopMode( void )
{
if( ( LowPowerDisableDuringTask == false ) && ( RtcTimerEventAllowsLowPower == true ) )
{
BoardDeInitMcu( );
// Disable the Power Voltage Detector
HAL_PWR_DisablePVD( );
SET_BIT( PWR->CR, PWR_CR_CWUF );
// Enable Ultra low power mode
HAL_PWREx_EnableUltraLowPower( );
// Enable the fast wake up from Ultra low power mode
HAL_PWREx_EnableFastWakeUp( );
// Enter Stop Mode
HAL_PWR_EnterSTOPMode( PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI );
}
}
void deepsleep(void)
{
// Stop HAL systick
HAL_SuspendTick();
// Request to enter STOP mode with regulator in low power mode
#if TARGET_STM32L4
HAL_PWREx_EnterSTOP2Mode(PWR_STOPENTRY_WFI);
#else /* TARGET_STM32L4 */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
#endif /* TARGET_STM32L4 */
// Restart HAL systick
HAL_ResumeTick();
// After wake-up from STOP reconfigure the PLL
SetSysClock();
#if DEVICE_LOWPOWERTIMER
rtc_synchronize();
#endif
}
/// \function stop()
STATIC mp_obj_t pyb_stop(void) {
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
// reconfigure the system clock after waking up
// enable HSE
__HAL_RCC_HSE_CONFIG(RCC_HSE_ON);
while (!__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY)) {
}
// enable PLL
__HAL_RCC_PLL_ENABLE();
while (!__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY)) {
}
// select PLL as system clock source
MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_SYSCLKSOURCE_PLLCLK);
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) {
}
return mp_const_none;
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_I2C1_Init();
MX_USART2_UART_Init();
/* USER CODE BEGIN 2 */
HAL_DBGMCU_EnableDBGSleepMode();
HAL_SuspendTick(); // we don't want systick to wake us up every 1ms
main_app();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI);
}
/* USER CODE END 3 */
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32L0xx HAL library initialization:
- Configure the Flash prefetch, Flash preread and Buffer caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED3 */
BSP_LED_Init(LED3);
/* Configure the system clock @ 32 Mhz */
SystemClock_Config();
/* Configure the system Power */
SystemPower_Config();
while (1)
{
/* Insert 5 second delay */
HAL_Delay(5000);
/* Key button (EXTI_Line13) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SystemClockConfig_STOP();
}
}
/**
* @brief The application entry point.
*
* @retval None
*/
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */
SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_I2C1_Init();
MX_TIM3_Init();
//MX_IWDG_Init();
MX_TIM14_Init();
MX_TIM16_Init();
MX_TIM17_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_Encoder_Start(&htim3, TIM_CHANNEL_ALL);
HAL_NVIC_SetPriority(TIM3_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(TIM3_IRQn);
HAL_TIM_Base_Start_IT(&htim3);
// Seconds Counter startup duty
HAL_TIM_Base_Start_IT(&htim14);
HAL_TIM_Base_Stop_IT(&htim14);
HAL_TIM_Base_Start_IT(&htim16);
HAL_TIM_Base_Start_IT(&htim17);
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN, GPIO_PIN_RESET);
ssd1306_Init();
current_cursor = exposition;
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
//HAL_IWDG_Refresh(&hiwdg);
if(__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN, GPIO_PIN_SET);
else HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN, GPIO_PIN_RESET);
if (update_screen_flag)
{
ssd1306_Fill(Black);
ssd1306_UpdateScreen();
update_screen_flag = 0;
}
if (seconds_counter > STOP_TIME_SEC) //if more than 10 s need to stop
{
// Entering STOP Mode Procedure
seconds_counter = 0;
GPIO_InitTypeDef GPIO_InitStruct;
ssd1306_WriteCommand(0xAE); // OLED Off
GPIO_InitStruct.Pin = ENC_BUTTON_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_EVT_RISING_FALLING;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_NVIC_SetPriority(EXTI4_15_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(EXTI4_15_IRQn);
HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN|LED_RED_PIN|GATE_PIN|FOCUS_PIN, GPIO_PIN_RESET);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFE);
// Exit from STOP Mode procedure
SystemClock_Config();
ssd1306_WriteCommand(0xAF); // OLED On
GPIO_InitStruct.Pin = ENC_BUTTON_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
current_state = menu_navigation;
}
Menu();
if (current_state == running_timer || current_state == running_interval)
{
if(gate_flag)
{
// Reset Gate & Focus
HAL_GPIO_WritePin(GPIOA, FOCUS_PIN, GPIO_PIN_RESET);
HAL_GPIO_WritePin(GPIOA, GATE_PIN, GPIO_PIN_RESET);
HAL_TIM_Base_Stop_IT(&htim14);
HAL_Delay(500);
__HAL_TIM_SET_COUNTER(&htim14, 0);
HAL_TIM_Base_Start_IT(&htim14);
gate_flag = 0;
// If not last shot, go to Interval state
if(tmp_num_shots != 0)
{
tmp_int_minutes = set_int_minutes;
tmp_int_sec = set_int_sec;
tmp_exp_minutes = set_exp_minutes;
tmp_exp_sec = set_exp_sec;
current_state = running_interval;
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN,GPIO_PIN_RESET); // 1s LED Off
}
else
{
HAL_TIM_Base_Stop_IT(&htim14);
__HAL_TIM_SET_COUNTER(&htim14, 0);
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN,GPIO_PIN_RESET); // 1s LED Off
tmp_exp_minutes = set_exp_minutes;
tmp_exp_sec = set_exp_sec;
current_state = menu_navigation;
update_screen_flag = 1;
}
}
}
if (exiting_run)
{
HAL_TIM_Base_Stop_IT(&htim16);
HAL_Delay(1000);
exiting_run = 0;
HAL_TIM_Base_Start_IT(&htim16);
HAL_GPIO_WritePin(GPIOA, FOCUS_PIN, GPIO_PIN_RESET);
HAL_GPIO_WritePin(GPIOA, GATE_PIN, GPIO_PIN_RESET);
}
}
/* USER CODE END 3 */
}
/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSE/LSI
* =====================================
* - RTC Clocked by LSE or LSI
* - Regulator in LP mode
* - HSI, HSE OFF and LSI OFF if not used as RTC Clock source
* - No IWDG
* - FLASH in deep power down mode
* - Automatic Wakeup using RTC clocked by LSE/LSI (~20s)
* @param None
* @retval None
*/
void StopMode_Measure(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOD_CLK_ENABLE();
__HAL_RCC_GPIOE_CLK_ENABLE();
__HAL_RCC_GPIOF_CLK_ENABLE();
__HAL_RCC_GPIOG_CLK_ENABLE();
__HAL_RCC_GPIOH_CLK_ENABLE();
__HAL_RCC_GPIOI_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pin = GPIO_PIN_All;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOH, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* Disable GPIOs clock */
__HAL_RCC_GPIOA_CLK_DISABLE();
__HAL_RCC_GPIOB_CLK_DISABLE();
__HAL_RCC_GPIOC_CLK_DISABLE();
__HAL_RCC_GPIOD_CLK_DISABLE();
__HAL_RCC_GPIOE_CLK_DISABLE();
__HAL_RCC_GPIOF_CLK_DISABLE();
__HAL_RCC_GPIOG_CLK_DISABLE();
__HAL_RCC_GPIOH_CLK_DISABLE();
__HAL_RCC_GPIOI_CLK_DISABLE();
RTCHandle.Instance = RTC;
/* Configure RTC prescaler and RTC data registers as follow:
- Hour Format = Format 24
- Asynch Prediv = Value according to source clock
- Synch Prediv = Value according to source clock
- OutPut = Output Disable
- OutPutPolarity = High Polarity
- OutPutType = Open Drain */
RTCHandle.Init.HourFormat = RTC_HOURFORMAT_24;
RTCHandle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
RTCHandle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
RTCHandle.Init.OutPut = RTC_OUTPUT_DISABLE;
RTCHandle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
RTCHandle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;
if(HAL_RTC_Init(&RTCHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/*## Configure the Wake up timer ###########################################*/
/* RTC Wakeup Interrupt Generation:
Wakeup Time Base = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSI))
Wakeup Time = Wakeup Time Base * WakeUpCounter
= (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSI)) * WakeUpCounter
==> WakeUpCounter = Wakeup Time / Wakeup Time Base
To configure the wake up timer to 20s the WakeUpCounter is set to 0xA017:
RTC_WAKEUPCLOCK_RTCCLK_DIV = RTCCLK_Div16 = 16
Wakeup Time Base = 16 /(~32.768KHz) = ~0,488 ms
Wakeup Time = ~20s = 0,488ms * WakeUpCounter
==> WakeUpCounter = ~20s/0,488ms = 40983 = 0xA017 */
HAL_RTCEx_SetWakeUpTimer_IT(&RTCHandle, 0xA017, RTC_WAKEUPCLOCK_RTCCLK_DIV16);
/* FLASH Deep Power Down Mode enabled */
HAL_PWREx_EnableFlashPowerDown();
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SYSCLKConfig_STOP();
/* Disable Wake-up timer */
if(HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure LED1, LED2, LED3 and LED4 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* Configure the system clock to 168 MHz */
SystemClock_Config();
/* Configure Key Button (EXTI_Line15) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);
/*## Configure the RTC peripheral #######################################*/
RTCHandle.Instance = RTC;
/* Configure RTC prescaler and RTC data registers as follow:
- Hour Format = Format 24
- Asynch Prediv = Value according to source clock
- Synch Prediv = Value according to source clock
- OutPut = Output Disable
- OutPutPolarity = High Polarity
- OutPutType = Open Drain */
RTCHandle.Init.HourFormat = RTC_HOURFORMAT_24;
RTCHandle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
RTCHandle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
RTCHandle.Init.OutPut = RTC_OUTPUT_DISABLE;
RTCHandle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
RTCHandle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;
if(HAL_RTC_Init(&RTCHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
/* Insert 5 second delay */
HAL_Delay(5000);
/*## Configure the Wake up timer ###########################################*/
/* RTC Wakeup Interrupt Generation:
Wakeup Time Base = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI))
Wakeup Time = Wakeup Time Base * WakeUpCounter
= (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI)) * WakeUpCounter
==> WakeUpCounter = Wakeup Time / Wakeup Time Base
To configure the wake up timer to 4s the WakeUpCounter is set to 0x1FFF:
RTC_WAKEUPCLOCK_RTCCLK_DIV = RTCCLK_Div16 = 16
Wakeup Time Base = 16 /(~32.768KHz) = ~0,488 ms
Wakeup Time = ~4s = 0,488ms * WakeUpCounter
==> WakeUpCounter = ~4s/0,488ms = 8191 = 0x1FFF */
HAL_RTCEx_SetWakeUpTimer_IT(&RTCHandle, 0x1FFF, RTC_WAKEUPCLOCK_RTCCLK_DIV16);
/* Turn OFF LED's */
BSP_LED_Off(LED1);
BSP_LED_Off(LED2);
BSP_LED_Off(LED3);
BSP_LED_Off(LED4);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Disable Wakeup Counter */
HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle);
/* Configures system clock after wake-up from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SYSCLKConfig_STOP();
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32L0xx HAL library initialization:
- Configure the Flash prefetch
- Configure the Systick to generate an interrupt each 1 msec
- Low Level Initialization */
HAL_Init();
/* Configure LED3 */
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* Configure the system clock to 32 MHz */
SystemClock_Config();
/*##-1- Configure the LPUART peripheral ####################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* LPUART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
HAL_UART_DeInit(&UartHandle);
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef BOARD_IN_STOP_MODE
BSP_LED_On(LED3);
/* wait for two seconds before test start */
HAL_Delay(2000);
/* make sure that no LPUART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify wake-up on RXNE flag */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_READDATA_NONEMPTY;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the LPUART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by LPUART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up based on RXNE flag successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer1, COUNTOF(aTxBuffer1)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-2- Wake Up second step ###############################################*/
/* make sure that no UART transfer is on-going */
BSP_LED_On(LED3);
/* wait for two seconds before test start */
HAL_Delay(2000);
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that LPUART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify wake-up on start-bit detection */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_STARTBIT;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the LPUART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by LPUART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on start bit detection successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer2, COUNTOF(aTxBuffer2)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Wake Up third step ################################################*/
/* make sure that no LPUART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify address-to-match type.
* The address is 0x29, meaning the character triggering the
* address match is 0xA9 */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_ADDRESS;
WakeUpSelection.AddressLength = UART_ADDRESS_DETECT_7B;
WakeUpSelection.Address = 0x29;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the LPUART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by LPUART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on 7-bit address detection successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer3, COUNTOF(aTxBuffer3)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-4- Wake Up fourth step ###############################################*/
/* make sure that no LPUART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify address-to-match type.
* The address is 0x2, meaning the character triggering the
* address match is 0x82 */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_ADDRESS;
WakeUpSelection.AddressLength = UART_ADDRESS_DETECT_4B;
WakeUpSelection.Address = 0x2;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the LPUART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by LPUART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on 4-bit address detection successful */
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer4, COUNTOF(aTxBuffer4)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
#else
/* initialize the User push-button in Interrupt mode */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);
/* Wait for User push-button press before starting the test.
In the meantime, LED3 is blinking */
while(UserButtonStatus == 0)
{
/* Toggle LED3 */
BSP_LED_Toggle(LED3);
HAL_Delay(100);
}
/*##-2- Send the wake-up from stop mode first trigger ######################*/
/* (RXNE flag setting) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger1, COUNTOF(aWakeUpTrigger1)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put LPUART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer1)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer1,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer1)-1))
{
Error_Handler();
}
/* wait for two seconds before test second step */
HAL_Delay(2000);
/*##-3- Send the wake-up from stop mode second trigger #####################*/
/* (start Bit detection) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger2, COUNTOF(aWakeUpTrigger2)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put LPUART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer2)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer2,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer2)-1))
{
Error_Handler();
}
/* wait for two seconds before test third step */
HAL_Delay(2000);
/*##-4- Send the wake-up from stop mode third trigger ######################*/
/* (7-bit address match) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger3, 1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put LPUART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer3)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer3,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer3)-1))
{
Error_Handler();
}
/* wait for two seconds before test fourth and last step */
HAL_Delay(2000);
/*##-5- Send the wake-up from stop mode fourth trigger #####################*/
/* (4-bit address match) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger4, 1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put LPUART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer4)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer4,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer4)-1))
{
Error_Handler();
}
HAL_Delay(2000);
#endif /* BOARD_IN_STOP_MODE */
/* Turn on LED3 & LED4 if test passes then enter infinite loop */
BSP_LED_On(LED3);
BSP_LED_On(LED4);
while (1)
{
}
}
/**
* @brief This routine puts the MCU in stop mode
* @param None
* @retval None
*/
void MCU_Enter_StopMode(void)
{
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI); /* Infinite loop */
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 72 MHz */
SystemClock_Config();
/* Configure LED7, LED3 and LED9*/
BSP_LED_Init(LED7);
BSP_LED_Init(LED3);
BSP_LED_Init(LED9);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLED;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_AnalogFilter_Config(&I2cHandle,I2C_ANALOGFILTER_ENABLED);
#ifdef MASTER_BOARD
/* Configure USER Button*/
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for USER Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for USER Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Wait for USER Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for USER Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/*##-4- Put I2C peripheral in reception process ###########################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
#else
/*##-2- Enable I2C peripheral in wake up from stop mode ###################*/
HAL_I2CEx_EnableWakeUp(&I2cHandle);
/*##-3- Put I2C peripheral in reception process ###########################*/
if(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* enter stop mode */
/* Turn LED9 on */
BSP_LED_On(LED9);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/* Wake Up from Stop mode */
/* Turn LED9 off */
BSP_LED_Off(LED9);
/*##-4- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-5- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* enter stop mode */
/* Turn LED9 on */
BSP_LED_On(LED9);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
/* Wake Up from Stop mode */
/* Turn LED9 off */
BSP_LED_Off(LED9);
#endif /* MASTER_BOARD */
/*##-6- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-7- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/* Configure LED1, LED2, LED3 and LED4 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* WAKEUP button (EXTI_Line0) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_WAKEUP, BUTTON_MODE_EXTI);
/* Configure Key Button */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/*##-1- Configure the SDRAM device #########################################*/
/* SDRAM device configuration */
BSP_SDRAM_Init();
/*##-2- SDRAM memory write access ##########################################*/
/* Fill the buffer to write */
Fill_Buffer(aTxBuffer, BUFFER_SIZE, 0xA244250F);
/* Write data to the SDRAM memory */
BSP_SDRAM_WriteData(SDRAM_DEVICE_ADDR + WRITE_READ_ADDR, aTxBuffer, BUFFER_SIZE);
/* Wait for TAMPER/KEY to be pushed to enter stop mode */
while(BSP_PB_GetState(BUTTON_TAMPER) != RESET)
{
}
/*##-3- Issue self-refresh command to SDRAM device #########################*/
SDRAMCommandStructure.CommandMode = FMC_SDRAM_CMD_SELFREFRESH_MODE;
SDRAMCommandStructure.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK1;
SDRAMCommandStructure.AutoRefreshNumber = 1;
SDRAMCommandStructure.ModeRegisterDefinition = 0;
if(BSP_SDRAM_Sendcmd(&SDRAMCommandStructure) != HAL_OK)
{
/* Command send Error */
Error_Handler();
}
/*##-4- Enter CPU power stop mode ##########################################*/
/* Put LED4 on to indicate entering to STOP mode */
BSP_LED_On(LED4);
/* Request to enter STOP mode */
HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI);
/*##-5- Wakeup CPU from power stop mode ###################################*/
/* Configure the system clock after wakeup from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SystemClock_Config();
/*##-6- SDRAM memory read back access ######################################*/
SDRAMCommandStructure.CommandMode = FMC_SDRAM_CMD_NORMAL_MODE;
if(BSP_SDRAM_Sendcmd(&SDRAMCommandStructure) != HAL_OK)
{
/* Command send Error */
Error_Handler();
}
/* Read back data from the SDRAM memory */
BSP_SDRAM_ReadData(SDRAM_DEVICE_ADDR + WRITE_READ_ADDR, aRxBuffer, BUFFER_SIZE);
/*##-7- Checking data integrity ############################################*/
uwWriteReadStatus = Buffercmp(aTxBuffer, aRxBuffer, BUFFER_SIZE);
if (uwWriteReadStatus != PASSED)
{
/* KO */
/* Turn on LED2 */
BSP_LED_On(LED2);
}
else
{
/* OK */
/* Turn on LED1 */
BSP_LED_On(LED1);
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief This function configures the system to enter Stop mode with RTC
* clocked by LSE or LSI for current consumption measurement purpose.
* STOP Mode with RTC clocked by LSE/LSI
* =====================================
* - RTC Clocked by LSE or LSI
* - Regulator in LP mode
* - HSI, HSE OFF and LSI OFF if not used as RTC Clock source
* - No IWDG
* - Automatic Wakeup using RTC clocked by LSE/LSI (~20s)
* @param None
* @retval None
*/
void StopRTCMode_Measure(void)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Configure all GPIO as analog to reduce current consumption on non used IOs */
/* Enable GPIOs clock */
/* Warning : Reconfiguring all GPIO will close the connexion with the debugger */
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOD_CLK_ENABLE();
__HAL_RCC_GPIOF_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Pin = GPIO_PIN_All;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/* Disable GPIOs clock */
__HAL_RCC_GPIOA_CLK_DISABLE();
__HAL_RCC_GPIOB_CLK_DISABLE();
__HAL_RCC_GPIOC_CLK_DISABLE();
__HAL_RCC_GPIOD_CLK_DISABLE();
__HAL_RCC_GPIOF_CLK_DISABLE();
RTCHandle.Instance = RTC;
/* Configure RTC prescaler and RTC data registers as follows:
- Hour Format = Format 24
- Asynch Prediv = Value according to source clock
- Synch Prediv = Value according to source clock
- OutPut = Output Disable
- OutPutPolarity = High Polarity
- OutPutType = Open Drain */
RTCHandle.Init.HourFormat = RTC_HOURFORMAT_24;
RTCHandle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
RTCHandle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
RTCHandle.Init.OutPut = RTC_OUTPUT_DISABLE;
RTCHandle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
RTCHandle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;
if (HAL_RTC_Init(&RTCHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/*## Configure the Wake up timer ###########################################*/
/* RTC Wakeup Interrupt Generation:
Wakeup Time Base = (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI))
Wakeup Time = Wakeup Time Base * WakeUpCounter
= (RTC_WAKEUPCLOCK_RTCCLK_DIV /(LSE or LSI)) * WakeUpCounter
==> WakeUpCounter = Wakeup Time / Wakeup Time Base
To configure the wake up timer to 20s the WakeUpCounter is set to 0xA017:
RTC_WAKEUPCLOCK_RTCCLK_DIV = RTCCLK_Div16 = 16
Wakeup Time Base = 16 /(~32.768KHz) = ~0,488 ms
Wakeup Time = ~20s = 0,488ms * WakeUpCounter
==> WakeUpCounter = ~20s/0,488ms = 40983 = 0xA017 */
/* Disable Wake-up timer */
HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle);
HAL_RTCEx_SetWakeUpTimer_IT(&RTCHandle, 0xA017, RTC_WAKEUPCLOCK_RTCCLK_DIV16);
/* Configure User push-button as external interrupt generator */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
/* Enter Stop Mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* Configures system clock after wake-up from STOP: enable HSI and PLL with HSI as source*/
SystemClock_Config();
/* Disable Wake-up timer */
HAL_RTCEx_DeactivateWakeUpTimer(&RTCHandle);
}