int
main(void)
{
display[0] = '\0';
display2[0] = '\0';
// Set the clocking to run directly from the crystal.
SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_8MHZ);
// Initialize the OLED display and write status.
RIT128x96x4Init(1000000);
RIT128x96x4StringDraw("----------------------", 0, 50, 15);
// Enable the peripherals used by this example.
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART1);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
// Status
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPadConfigSet(GPIO_PORTF_BASE,GPIO_PIN_0,GPIO_STRENGTH_4MA,GPIO_PIN_TYPE_STD);
GPIODirModeSet(GPIO_PORTF_BASE,GPIO_PIN_0,GPIO_DIR_MODE_OUT);
//PB1
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIOPadConfigSet(GPIO_PORTB_BASE,GPIO_PIN_1,GPIO_STRENGTH_4MA,GPIO_PIN_TYPE_STD);
GPIODirModeSet(GPIO_PORTB_BASE,GPIO_PIN_1,GPIO_DIR_MODE_IN);
GPIOPortIntRegister(GPIO_PORTB_BASE, PortBIntHandler);
GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_1, GPIO_BOTH_EDGES);
GPIOPinIntEnable(GPIO_PORTB_BASE, GPIO_PIN_1);
IntPrioritySet(INT_GPIOB,0x80);
SysTickIntRegister(SysTickHandler);
SysTickPeriodSet(SysCtlClockGet()/10000); // 0.1ms
SysTickIntEnable();
waitTime = 0; // initialize
waitTime2 = 0;
SysTickEnable();
// Enable processor interrupts.
IntMasterEnable();
// Set GPIO A0 and A1 as UART pins.
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
GPIOPinTypeUART(GPIO_PORTD_BASE, GPIO_PIN_2 | GPIO_PIN_3);
// Configure the UART for 115,200, 8-N-1 operation.
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 9600,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
UARTConfigSetExpClk(UART1_BASE, SysCtlClockGet(), 9600,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
// Enable the UART interrupt.
IntEnable(INT_UART0);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
IntEnable(INT_UART1);
UARTIntEnable(UART1_BASE, UART_INT_RX | UART_INT_RT);
while(1)
{
}
}
void UART1Send(unsigned char *pucBuffer, unsigned ulCount)
{
tBoolean bRc;
static int FCount = 0;
static int SCount = 0;
//
// Loop while there are more characters to send.
//
if(m_nTxBuffIn1 + ulCount >= TXBUFFSIZE1)
{
// No place to put new data
// To be sure we purge all tx data
//IntDisable(INT_UART1);
/* Start the Tx of the message on the UART. */
UARTIntDisable( UART1_BASE, UART_INT_TX );
#if 0 // Sent all data buffer until empty and put new data in to the buffer for sent
// Fill hardware FIFO
while(m_nTxBuffIn1 > 0)
{
bRc = UARTCharPutNonBlocking(UART1_BASE,m_tTxBuff1[m_nTxNextNdx1]);
if(bRc == true)
{
m_nTxNextNdx1++;
m_nTxBuffIn1--;
}
}
memcpy(m_tTxBuff1 ,pucBuffer,ulCount);
m_nTxNextNdx1 = 0;
m_nTxBuffIn1 = ulCount;
#else // Throw all data buffer and put new data in to buffer for sent
//memcpy(m_tTxBuff1 ,pucBuffer,ulCount);
//m_nTxNextNdx1 = 0;
//m_nTxBuffIn1 = ulCount;
// Fill hardware FIFO
bRc = true;
while(m_nTxBuffIn1 > 0 && bRc == true)
{
bRc = UARTCharPutNonBlocking(UART1_BASE,m_tTxBuff1[m_nTxNextNdx1]);
if(bRc == true)
{
m_nTxNextNdx1++;
m_nTxBuffIn1--;
}
}
#endif
//IntEnable(INT_UART1);
UARTIntEnable(UART1_BASE, UART_INT_TX);
}
else if(ulCount > 0)
{
//IntDisable(INT_UART1);
/* Start the Tx of the message on the UART. */
UARTIntDisable( UART1_BASE, UART_INT_TX );
if(m_nTxBuffIn1 > 0)
{
// Move TX data to start
if(m_nTxNextNdx1 > 0)
{
memmove(m_tTxBuff1,&m_tTxBuff1[m_nTxNextNdx1],m_nTxBuffIn1);
}
m_nTxNextNdx1 = 0;
// Add data to TXBuff
memcpy(&m_tTxBuff1[m_nTxBuffIn1],pucBuffer,ulCount);
m_nTxBuffIn1 += ulCount;
}
else
{
memcpy(m_tTxBuff1 ,pucBuffer,ulCount);
m_nTxNextNdx1 = 0;
m_nTxBuffIn1 = ulCount;
}
// Fill hardware FIFO
bRc = true;
while(m_nTxBuffIn1 > 0 && bRc == true)
{
bRc = UARTCharPutNonBlocking(UART1_BASE,m_tTxBuff1[m_nTxNextNdx1]);
if(bRc == true)
{
m_nTxNextNdx1++;
m_nTxBuffIn1--;
}
}
//IntEnable(INT_UART1);
UARTIntEnable(UART1_BASE, UART_INT_TX);
}
}
static void vSerialTxCoRoutine( xCoRoutineHandle xHandle, unsigned portBASE_TYPE uxIndex )
{
portTickType xDelayPeriod;
static unsigned long *pulRandomBytes = mainFIRST_PROGRAM_BYTES;
/* Co-routine MUST start with a call to crSTART. */
crSTART( xHandle );
for(;;)
{
/* Was the previously transmitted string received correctly? */
if( uxErrorStatus != pdPASS )
{
/* An error was encountered so set the error LED. */
vSetErrorLED();
}
/* The next character to Tx is the first in the string. */
cNextChar = mainFIRST_TX_CHAR;
UARTIntDisable( UART0_BASE, UART_INT_TX );
{
/* Send the first character. */
if( !( HWREG( UART0_BASE + UART_O_FR ) & UART_FR_TXFF ) )
{
HWREG( UART0_BASE + UART_O_DR ) = cNextChar;
}
/* Move the variable to the char to Tx on so the ISR transmits
the next character in the string once this one has completed. */
cNextChar++;
}
UARTIntEnable(UART0_BASE, UART_INT_TX);
/* Toggle the LED to show a new string is being transmitted. */
vParTestToggleLED( mainCOMMS_TX_LED );
/* Delay before we start the string off again. A pseudo-random delay
is used as this will provide a better test. */
xDelayPeriod = xTaskGetTickCount() + ( *pulRandomBytes );
pulRandomBytes++;
if( pulRandomBytes > mainTOTAL_PROGRAM_MEMORY )
{
pulRandomBytes = mainFIRST_PROGRAM_BYTES;
}
/* Make sure we don't wait too long... */
xDelayPeriod &= mainMAX_TX_DELAY;
/* ...but we do want to wait. */
if( xDelayPeriod < mainMIN_TX_DELAY )
{
xDelayPeriod = mainMIN_TX_DELAY;
}
/* Block for the random(ish) time. */
crDELAY( xHandle, xDelayPeriod );
}
/* Co-routine MUST end with a call to crEND. */
crEND();
}
/*
** The main function
*/
int main()
{
unsigned int divisorValue = 0;
/* Configuring the system clocks for UART0 instance. */
UART0ModuleClkConfig();
/* Initializing the ARM Interrupt Controller. */
IntAINTCInit();
/* Performing the Pin Multiplexing for UART0 instance. */
UARTPinMuxSetup(0);
/* Performing a module reset. */
UARTModuleReset(UART_INST_BASE);
UARTFIFOConfig(UART_INST_BASE,
UART_FIFO_CONFIG(UART_TRIG_LVL_GRANULARITY_1,
UART_TRIG_LVL_GRANULARITY_1,
1, 1, 1, 1, UART_DMA_EN_PATH_SCR,
UART_DMA_MODE_0_ENABLE));
/* Computing the Divisor Value. */
divisorValue = UARTDivisorValCompute(UART_MODULE_INPUT_CLK,
BAUD_RATE_115200,
UART16x_OPER_MODE,
UART_MIR_OVERSAMPLING_RATE_42);
/* Programming the Divisor Latches. */
UARTDivisorLatchWrite(UART_INST_BASE, divisorValue);
/* Switching to Configuration Mode B. */
UARTRegConfigModeEnable(UART_INST_BASE, UART_REG_CONFIG_MODE_B);
/* Programming the Line Characteristics. */
UARTLineCharacConfig(UART_INST_BASE,
(UART_FRAME_WORD_LENGTH_8 | UART_FRAME_NUM_STB_1),
UART_PARITY_NONE);
/* Disabe write access to Divisor Latches. */
UARTDivisorLatchDisable(UART_INST_BASE);
/* Disable Break Control. */
UARTBreakCtl(UART_INST_BASE, UART_BREAK_COND_DISABLE);
/* Switch to UART16x operating mode. */
UARTOperatingModeSelect(UART_INST_BASE, UART16x_OPER_MODE);
UARTIntEnable(UART_INST_BASE, (UART_INT_LINE_STAT | UART_INT_THR |
UART_INT_RHR_CTI));
/* Register the Interrupt Service Routines */
IntRegister(RTC_INT_NUM, RTCIsr);
IntRegister(UART_INT_NUM, UARTIsr);
IntRegister(TIMER_INT_NUM, DMTimerIsr);
/*
** Setting the priority for the system interrupt in AINTC.
** Timer interrupt is given highest priority - 1
** RTC interrupt is given medium priority - 2
** UART interrupt is given lowest priority - 4
*/
IntPrioritySet(TIMER_INT_NUM, IRQ_PRIORITY_TIMER, AINTC_HOSTINT_ROUTE_IRQ);
IntPrioritySet(RTC_INT_NUM, IRQ_PRIORITY_RTC, AINTC_HOSTINT_ROUTE_IRQ);
IntPrioritySet(UART_INT_NUM, IRQ_PRIORITY_UART, AINTC_HOSTINT_ROUTE_IRQ);
/* Enabling the system interrupt in AINTC for UART */
IntSystemEnable(UART_INT_NUM);
IntMasterIRQEnable();
while(1);
}
void UART0Send(unsigned char *pucBuffer, unsigned ulCount)
{
tBoolean bRc;
static int FCount = 0;
static int SCount = 0;
//
// Loop while there are more characters to send.
//
if(m_nTxBuffIn + ulCount >= TXBUFFSIZE)
{
// No place to put new data
// To be sure we purge all tx data
//IntDisable(INT_UART0);
/* Start the Tx of the message on the UART. */
UARTIntDisable( UART0_BASE, UART_INT_TX );
#if 0
// TX int
// Push next char to transmitter
while(m_nTxBuffIn > 0)
{
bRc = UARTCharPutNonBlocking(UART0_BASE,m_tTxBuff[m_nTxNextNdx]);
if(bRc == true)
{
m_nTxNextNdx++;
m_nTxBuffIn--;
}
}
memcpy(m_tTxBuff ,pucBuffer,ulCount);
m_nTxNextNdx = 0;
m_nTxBuffIn = ulCount;
#else
//memcpy(m_tTxBuff ,pucBuffer,ulCount);
//m_nTxNextNdx = 0;
//m_nTxBuffIn = ulCount;
// Fill hardware FIFO
bRc = true;
while(m_nTxBuffIn > 0 && bRc == true)
{
bRc = UARTCharPutNonBlocking(UART0_BASE,m_tTxBuff[m_nTxNextNdx]);
if(bRc == true)
{
m_nTxNextNdx++;
m_nTxBuffIn--;
}
}
#endif
UARTIntEnable(UART0_BASE, UART_INT_TX);
//IntEnable(INT_UART0);
}
else if(ulCount > 0)
{
//IntDisable(INT_UART0);
/* Start the Tx of the message on the UART. */
UARTIntDisable( UART0_BASE, UART_INT_TX );
if(m_nTxBuffIn > 0)
{
// Move TX data to start
if(m_nTxNextNdx > 0)
{
memmove(m_tTxBuff,&m_tTxBuff[m_nTxNextNdx],m_nTxBuffIn);
}
m_nTxNextNdx = 0;
// Add data to TXBuff
memcpy(&m_tTxBuff[m_nTxBuffIn],pucBuffer,ulCount);
m_nTxBuffIn += ulCount;
}
else
{
memcpy(m_tTxBuff ,pucBuffer,ulCount);
m_nTxNextNdx = 0;
m_nTxBuffIn = ulCount;
}
// Fill hardware FIFO
bRc = true;
while(m_nTxBuffIn > 0 && bRc == true)
{
bRc = UARTCharPutNonBlocking(UART0_BASE,m_tTxBuff[m_nTxNextNdx]);
if(bRc == true)
{
m_nTxNextNdx++;
m_nTxBuffIn--;
}
}
UARTIntEnable(UART0_BASE, UART_INT_TX);
//IntEnable(INT_UART0);
}
}
void uart_enableInterrupts(){
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_TX | UART_INT_RT);
}
// Functions
void SAD_Initialize(DriverRegisters* sadreg, role_t setRole, unsigned short setBaud)
{
#ifdef SAD_DEBUG
RIT128x96x4Init(1000000);
#endif
// initializing these values is messy but works for now
sadreg->hs_baud.validbauds[0] = 1200;
sadreg->hs_baud.validbauds[1] = 2400;
sadreg->hs_baud.validbauds[2] = 9600;
sadreg->hs_baud.validbauds[3] = 38400;
// Initialize global flags and vars
//UARTRX_FLAG = 0;
//SYSTICKINT_FLAG = 0;
//GLOBALTIME.hours = 0;
//GLOBALTIME.mins = 0;
//GLOBALTIME.seconds = 0;
//GLOBALTIME.milisecs = 0;
// set relevent structure attributes based on provided parameters
sadreg->role = setRole;
sadreg->txbaud = setBaud;
// Based on the role, set the initial state for the state machine
//sadreg->state = (sadreg->role == TXER) ? HANDSHAKE_TX : HANDSHAKE_RX;
// Initialize the hand shake counter to 0
//sadreg->hs_cnt = 0;
// Initialize the circle buffer
//init_cbuff(&sadreg->circbuf);
SAD_timerinit(sadreg);
// Initialize rx baud to 0
//sadreg->rxbaud = 0;
// Initialize hand shake baude pointer
//sadreg->hs_baud.currentbaudchoice = 0;
// Initialize tx baud to first element in valid baud rates array
//sadreg->txbaud = sadreg->hs_baud.validbauds[sadreg->hs_baud.currentbaudchoice];
// Use Systick timer
SysTickIntRegister(&SysTickTimerHandler);
SysTickPeriodSet(sadreg->timer.limit); // set to rollover every 1ms
SysTickIntEnable();
SysTickEnable();
// Initialize HW Timer
/* SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0); */
/* TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC); */
/* TimerLoadSet(TIMER0_BASE, TIMER_A, SysCtlClockGet()); */
/* IntEnable(INT_TIMER0A); */
/* TimerEnable(TIMER0_BASE, TIMER_A); */
// Initialize UART0
// UART0_TX : PA1
// UART0_RX : PA0
// Enable UART Peripherals
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
// Set GPIO A0 and A1 as UART pins.
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
// Configure the UART for 115,200, 8-N-1 operation.
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
// Enable the UART interrupt.
IntEnable(INT_UART0);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
// Initialize UART1
// UART1_TX : PD3
// UART1_RX : PD2
// disable fifos
// Enable UART Peripherals
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART1);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
// Set GPIO A0 and A1 as UART pins.
GPIOPinTypeUART(GPIO_PORTD_BASE, GPIO_PIN_2 | GPIO_PIN_3);
// Configure the UART for SADreg baud, 8-N-1 operation.
UARTConfigSetExpClk(UART1_BASE, SysCtlClockGet(), sadreg->txbaud,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
// Disable fifos, fifo is of depth 1,
//UARTFIFODisable(UART1_BASE);
// Enable the UART interrupt.
IntEnable(INT_UART1);
UARTIntEnable(UART1_BASE, UART_INT_RX | UART_INT_RT);
// Enable processor interrupts.
IntMasterEnable();
}
/*************************************************************************************************
* @fn HalUARTOpenIsr()
*
* @brief Open a port based on the configuration
*
* @param port - UART port
* config - contains configuration information
* cBack - Call back function where events will be reported back
*
* @return Status of the function call
*************************************************************************************************/
uint8 HalUARTOpenIsr(uint8 port, halUARTCfg_t *config)
{
if (uartRecord.configured)
{
HalUARTClose(port);
}
if (config->baudRate > HAL_UART_BR_115200)
{
return HAL_UART_BAUDRATE_ERROR;
}
if (((uartRecord.rx.pBuffer = osal_mem_alloc(config->rx.maxBufSize)) == NULL) ||
((uartRecord.tx.pBuffer = osal_mem_alloc(config->tx.maxBufSize)) == NULL))
{
if (uartRecord.rx.pBuffer != NULL)
{
osal_mem_free(uartRecord.rx.pBuffer);
uartRecord.rx.pBuffer = NULL;
}
return HAL_UART_MEM_FAIL;
}
if(config->flowControl)
{
IOCPinConfigPeriphOutput(GPIO_D_BASE, GPIO_PIN_3, IOC_MUX_OUT_SEL_UART1_RTS);
GPIOPinTypeUARTOutput(GPIO_D_BASE, GPIO_PIN_3);
IOCPinConfigPeriphInput(GPIO_B_BASE, GPIO_PIN_0, IOC_UARTCTS_UART1);
GPIOPinTypeUARTInput(GPIO_B_BASE, GPIO_PIN_0);
}
IntEnable(HAL_UART_INT_CTRL);
uartRecord.configured = TRUE;
uartRecord.baudRate = config->baudRate;
uartRecord.flowControl = config->flowControl;
uartRecord.flowControlThreshold = (config->flowControlThreshold > config->rx.maxBufSize) ? 0 :
config->flowControlThreshold;
uartRecord.idleTimeout = config->idleTimeout;
uartRecord.rx.maxBufSize = config->rx.maxBufSize;
uartRecord.tx.maxBufSize = config->tx.maxBufSize;
uartRecord.intEnable = config->intEnable;
uartRecord.callBackFunc = config->callBackFunc;
UARTConfigSetExpClk(HAL_UART_PORT, SysCtrlClockGet(), UBRRTable[uartRecord.baudRate],
(UART_CONFIG_WLEN_8 | UART_CONFIG_PAR_NONE | UART_CONFIG_STOP_ONE));
/* FIFO level set to 1/8th for both RX and TX which is 2 bytes */
UARTFIFOLevelSet(HAL_UART_PORT, UART_FIFO_TX1_8, UART_FIFO_RX1_8);
UARTFIFOEnable(HAL_UART_PORT);
/* Clear and enable UART TX, RX, CTS and Recieve Timeout interrupt */
UARTIntClear(HAL_UART_PORT, (UART_INT_RX | UART_INT_TX | UART_INT_CTS | UART_INT_RT ));
UARTIntEnable(HAL_UART_PORT, (UART_INT_RX | UART_INT_TX | UART_INT_CTS | UART_INT_RT ));
if(config->flowControl)
{
/* Enable hardware flow control by enabling CTS and RTS */
HWREG(HAL_UART_PORT + UART_O_CTL) |= (UART_CTL_CTSEN | UART_CTL_RTSEN );
}
UARTEnable(HAL_UART_PORT);
return HAL_UART_SUCCESS;
}
//*****************************************************************************
//
// This example demonstrates how to send a string of data to the UART.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run directly from the crystal.
//
SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_8MHZ);
//
// Initialize the OLED display and write status.
//
RIT128x96x4Init(1000000);
RIT128x96x4StringDraw("UART Echo", 36, 0, 15);
RIT128x96x4StringDraw("Port: Uart 0", 12, 16, 15);
RIT128x96x4StringDraw("Baud: 115,200 bps", 12, 24, 15);
RIT128x96x4StringDraw("Data: 8 Bit", 12, 32, 15);
RIT128x96x4StringDraw("Parity: None", 12, 40, 15);
RIT128x96x4StringDraw("Stop: 1 Bit", 12, 48, 15);
//
// Enable the peripherals used by this example.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable processor interrupts.
//
IntMasterEnable();
//
// Set GPIO A0 and A1 as UART pins.
//
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure the UART for 115,200, 8-N-1 operation.
//
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE));
//
// Enable the UART interrupt.
//
IntEnable(INT_UART0);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
//
// Prompt for text to be entered.
//
UARTSend((unsigned char *)"Enter text: ", 12);
//
// Loop forever echoing data through the UART.
//
while(1)
{
}
}
int main(void) {
uint32_t ui32ADC0Value[4];
ui32TempSet = 25;
// Set System CLock
SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
// Enaable UART
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
// Enable GPIO
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
// Enable ADC Peripheral
SysCtlPeripheralEnable(SYSCTL_PERIPH_ADC0);
//Allow the ADC12 to run at its default rate of 1Msps.
ADCSequenceConfigure(ADC0_BASE, 1, ADC_TRIGGER_PROCESSOR, 0);
//our code will average all four samples of temperature sensor data ta on sequencer 1 to calculate the temperature, so all four sequencer steps will measure the temperature sensor
ADCSequenceStepConfigure(ADC0_BASE, 1, 0, ADC_CTL_TS);
ADCSequenceStepConfigure(ADC0_BASE, 1, 1, ADC_CTL_TS);
ADCSequenceStepConfigure(ADC0_BASE, 1, 2, ADC_CTL_TS);
ADCSequenceStepConfigure(ADC0_BASE,1,3,ADC_CTL_TS|ADC_CTL_IE|ADC_CTL_END);
//enable ADC sequencer 1.
ADCSequenceEnable(ADC0_BASE, 1);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
IntMasterEnable();
IntEnable(INT_UART0);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2|GPIO_PIN_1|GPIO_PIN_3);
// Set bit rate fr serial communication
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
while (1)
{
//indication that the ADC conversion process is complete
ADCIntClear(ADC0_BASE, 1);
//trigger the ADC conversion with software
ADCProcessorTrigger(ADC0_BASE, 1);
//wait for the conversion to complete
while(!ADCIntStatus(ADC0_BASE, 1, false))
{
}
//read the ADC value from the ADC Sample Sequencer 1 FIFO
ADCSequenceDataGet(ADC0_BASE, 1, ui32ADC0Value);
ui32TempAvg = (ui32ADC0Value[0] + ui32ADC0Value[1] + ui32ADC0Value[2] + ui32ADC0Value[3] + 2)/4;
ui32TempValueC = (1475 - ((2475 * ui32TempAvg)) / 4096)/10;
ui32TempValueF = ((ui32TempValueC * 9) + 160) / 5;
print_temp(ui32TempValueC);
SysCtlDelay(SysCtlClockGet() / 3); //delay ~1 sec
if(ui32TempValueC < ui32TempSet)
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3, 8);
else
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3, 2);
}
}
int main()
{
unsigned int numByteChunks = 0;
unsigned int remainBytes = 0;
unsigned int bIndex = 0;
/* Configuring the system clocks for UART0 instance. */
UART0ModuleClkConfig();
/* Performing the Pin Multiplexing for UART0 instance. */
UARTPinMuxSetup(0);
/* Performing a module reset. */
UARTModuleReset(SOC_UART_0_REGS);
/* Performing FIFO configurations. */
UartFIFOConfigure();
/* Performing Baud Rate settings. */
UartBaudRateSet();
/* Switching to Configuration Mode B. */
UARTRegConfigModeEnable(SOC_UART_0_REGS, UART_REG_CONFIG_MODE_B);
/* Programming the Line Characteristics. */
UARTLineCharacConfig(SOC_UART_0_REGS,
(UART_FRAME_WORD_LENGTH_8 | UART_FRAME_NUM_STB_1),
UART_PARITY_NONE);
/* Disabling write access to Divisor Latches. */
UARTDivisorLatchDisable(SOC_UART_0_REGS);
/* Disabling Break Control. */
UARTBreakCtl(SOC_UART_0_REGS, UART_BREAK_COND_DISABLE);
/* Switching to UART16x operating mode. */
UARTOperatingModeSelect(SOC_UART_0_REGS, UART16x_OPER_MODE);
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
/* Performing Interrupt configurations. */
UartInterruptEnable();
numByteChunks = (sizeof(txArray) - 1) / NUM_TX_BYTES_PER_TRANS;
remainBytes = (sizeof(txArray) - 1) % NUM_TX_BYTES_PER_TRANS;
while(1)
{
/* This branch is entered if the transmission is not yet complete. */
if(TRUE == txEmptyFlag)
{
if(bIndex < numByteChunks)
{
/* Transmitting bytes in chunks of NUM_TX_BYTES_PER_TRANS. */
currNumTxBytes += UARTFIFOWrite(SOC_UART_0_REGS,
&txArray[currNumTxBytes],
NUM_TX_BYTES_PER_TRANS);
bIndex++;
}
else
{
/* Transmitting remaining data from the data block. */
currNumTxBytes += UARTFIFOWrite(SOC_UART_0_REGS,
&txArray[currNumTxBytes],
remainBytes);
}
txEmptyFlag = FALSE;
/*
** Re-enables the Transmit Interrupt. This interrupt
** was disabled in the Transmit section of the UART ISR.
*/
UARTIntEnable(SOC_UART_0_REGS, UART_INT_THR);
}
}
}
//*****************************************************************************
//
// This example demonstrates how to send a string of data to the UART.
//
//*****************************************************************************
int main(void) {
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
FPUEnable();
FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
SysCtlClockSet(
SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN
| SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2).
//
GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
//
// Enable the peripherals used by this example.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable processor interrupts.
//
IntMasterEnable();
//
// Set GPIO A0 and A1 as UART pins.
//
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure the UART for 115,200, 8-N-1 operation.
//
UARTConfigSetExpClk(UART0_BASE, SysCtlClockGet(), 115200,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
//
// Enable the UART interrupt.
//
IntEnable(INT_UART0);
UARTIntEnable(UART0_BASE, UART_INT_RX | UART_INT_RT);
//
// Prompt for text to be entered.
//
UARTSend((unsigned char *) "Enter text: ", 14);
//
// Loop forever echoing data through the UART.
//
while (1) {
}
}