/******************************************************************************
* @fn aesDmaInit
*
* @brief Initilize DMA for AES engine
*
* input parameters
*
* @param None
*
* @return None
*/
void aesDmaInit( void )
{
halDMADesc_t *ch;
/* Fill in DMA channel 1 descriptor and define it as input */
ch = HAL_DMA_GET_DESC1234( HAL_DMA_AES_IN );
HAL_DMA_SET_DEST( ch, HAL_AES_IN_ADDR ); /* Input of the AES module */
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN ); /* Using the length field */
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_BYTE ); /* One byte is transferred each time */
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE ); /* A single byte is transferred each time */
HAL_DMA_SET_TRIG_SRC( ch, HAL_DMA_TRIG_ENC_DW ); /* Setting the AES module to generate the DMA trigger */
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_1 ); /* The address for data fetch is incremented by 1 byte */
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_0 ); /* The destination address is constant */
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_DISABLE ); /* The DMA complete interrupt flag is not set at completion */
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS ); /* Transferring all 8 bits in each byte */
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH ); /* DMA has priority */
/* Fill in DMA channel 2 descriptor and define it as output */
ch = HAL_DMA_GET_DESC1234( HAL_DMA_AES_OUT );
HAL_DMA_SET_SOURCE( ch, HAL_AES_OUT_ADDR ); /* Start address of the segment */
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN ); /* Using the length field */
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_BYTE ); /* One byte is transferred each time */
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE ); /* A single byte is transferred each time */
HAL_DMA_SET_TRIG_SRC( ch, HAL_DMA_TRIG_ENC_UP ); /* Setting the AES module to generate the DMA trigger */
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_0 ); /* The address for data fetch is constant */
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_1 ); /* The destination address is incremented by 1 byte */
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_DISABLE ); /* The DMA complete interrupt flag is not set at completion */
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS ); /* Transferring all 8 bits in each byte */
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH ); /* DMA has priority */
}
/******************************************************************************
* @fn AesDmaSetup
*
* @brief Sets up DMA of 16 byte block using CC2540 HW aes encryption engine
*
* input parameters
*
* @param Cstate - Pointer to output data.
* @param msg_out_len - message out length
* @param msg_in - pointer to input data.
* @param msg_in_len - message in length
*
* output parameters
*
* @param Cstate - Pointer to encrypted data.
*
* @return None
*
*/
void AesDmaSetup( uint8 *Cstate, uint16 msg_out_len, uint8 *msg_in, uint16 msg_in_len )
{
halDMADesc_t *ch;
/* Modify descriptors for channel 1 */
ch = HAL_DMA_GET_DESC1234( HAL_DMA_AES_IN );
HAL_DMA_SET_SOURCE( ch, msg_in );
HAL_DMA_SET_LEN( ch, msg_in_len );
/* Modify descriptors for channel 2 */
ch = HAL_DMA_GET_DESC1234( HAL_DMA_AES_OUT );
HAL_DMA_SET_DEST( ch, Cstate );
HAL_DMA_SET_LEN( ch, msg_out_len );
/* Arm DMA channels 1 and 2 */
HAL_DMA_CLEAR_IRQ( HAL_DMA_AES_IN );
HAL_DMA_ARM_CH( HAL_DMA_AES_IN );
do {
asm("NOP");
} while (!HAL_DMA_CH_ARMED(HAL_DMA_AES_IN));
HAL_DMA_CLEAR_IRQ( HAL_DMA_AES_OUT );
HAL_DMA_ARM_CH( HAL_DMA_AES_OUT );
do {
asm("NOP");
} while (!HAL_DMA_CH_ARMED(HAL_DMA_AES_OUT));
}
/******************************************************************************
* @fn AesLoadKey
*
* @brief Writes the key into the CC2540
*
* input parameters
*
* @param AesKey - Pointer to AES Key.
*
* @return None
*/
void AesLoadKey( uint8 *AesKey )
{
#if (defined HAL_AES_DMA) && (HAL_AES_DMA == TRUE)
halDMADesc_t *ch = HAL_DMA_GET_DESC1234( HAL_DMA_AES_IN );
/* Modify descriptors for channel 1 */
HAL_DMA_SET_SOURCE( ch, AesKey );
HAL_DMA_SET_LEN( ch, KEY_BLENGTH );
/* Arm DMA channel 1 */
HAL_DMA_CLEAR_IRQ( HAL_DMA_AES_IN );
HAL_DMA_ARM_CH( HAL_DMA_AES_IN );
do {
asm("NOP");
} while (!HAL_DMA_CH_ARMED(HAL_DMA_AES_IN));
/* Set AES mode */
AES_SET_ENCR_DECR_KEY_IV( AES_LOAD_KEY );
/* Kick it off, block until AES is ready */
AES_START();
while( !(ENCCS & 0x08) );
#else
/* Set AES mode */
AES_SET_ENCR_DECR_KEY_IV( AES_LOAD_KEY );
/* Load the block */
AesLoadBlock( AesKey );
#endif
}
/******************************************************************************
* @fn HalUARTArmTxDMA
*
* @brief Arm the Tx DMA channel.
*
* @param None
*
* @return None
*****************************************************************************/
static void HalUARTArmTxDMA(void)
{
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_TX);
HAL_DMA_SET_SOURCE(ch, dmaCfg.txBuf[dmaCfg.txSel]);
HAL_DMA_SET_LEN(ch, dmaCfg.txIdx[dmaCfg.txSel]);
dmaCfg.txSel ^= 1;
dmaCfg.txTrig = 1;
HAL_DMA_ARM_CH(HAL_DMA_CH_TX);
HalUARTPollTxTrigDMA();
if (DMA_PM)
{
HAL_UART_DMA_SET_RDY_OUT();
}
}
/******************************************************************************
* @fn HalUARTArmTxDMA
*
* @brief Arm the Tx DMA channel.
*
* @param None
*
* @return None
*****************************************************************************/
static void HalUARTArmTxDMA(void)
{
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_TX);
HAL_DMA_SET_SOURCE(ch, dmaCfg.txBuf[dmaCfg.txSel]);
HAL_DMA_SET_LEN(ch, dmaCfg.txIdx[dmaCfg.txSel]);
dmaCfg.txSel ^= 1;
dmaCfg.txTrig = 1;
HAL_DMA_ARM_CH(HAL_DMA_CH_TX);
/* Time to arm each DMA channel is 9 cycles as per the user's guide */
asm("nop"); asm("nop"); asm("nop"); asm("nop"); asm("nop");
asm("nop"); asm("nop"); asm("nop"); asm("nop");
HalUARTPollTxTrigDMA();
if (DMA_PM)
{
HAL_UART_DMA_SET_RDY_OUT();
}
}
/**************************************************************************************************
* @fn npSpiTxIsr
*
* @brief This function handles the DMA Tx complete interrupt.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void HalSpiTxIsr(void)
{
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_TX);
uint16 src;
HAL_SPI_DBG_LOG(0x20);
NP_SPI_ASSERT(halSpiState == NP_SPI_WAIT_TX);
HAL_DMA_GET_SOURCE( ch, src );
if ((uint8 *)src != halSpiBuf)
{
osal_msg_deallocate((uint8 *)src);
}
halSpiState = NP_SPI_IDLE;
// Callback is required so that client can schedule to call npSpiMonitor
// function.
npSpiTxCompleteCallback();
}
/**************************************************************************************************
* @fn HalUARTWriteSPI
*
* @brief Transmit data bytes as a SPI packet.
*
* input parameters
*
* @param buf - pointer to the memory of the data bytes to send.
* @param len - the length of the data bytes to send.
*
* output parameters
*
* None.
*
* @return Zero for any error; otherwise, 'len'.
*/
static spiLen_t HalUARTWriteSPI(uint8 *buf, spiLen_t len)
{
// Already in Tx or Rx transaction
#ifdef RBA_UART_TO_SPI
// The RBA Bridge is not written to handle re-writes so we must
// just let it write
if (spiTxLen != 0)
#else //!RBA_UART_TO_SPI
if (spiTxLen != 0 || SPI_RDY_OUT())
#endif
{
return 0;
}
if (len > SPI_MAX_DAT_LEN)
{
len = SPI_MAX_DAT_LEN;
}
spiTxLen = len;
writeActive = 1;
#if defined HAL_SPI_MASTER
spiTxPkt[SPI_LEN_IDX] = len;
(void)memcpy(spiTxPkt + SPI_DAT_IDX, buf, len);
spiCalcFcs(spiTxPkt);
spiTxPkt[SPI_SOF_IDX] = SPI_SOF;
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_SPI_CH_TX);
HAL_DMA_SET_LEN(ch, SPI_PKT_LEN(spiTxPkt)); /* DMA TX might need padding */
/* Abort any pending DMA operations */
HAL_DMA_ABORT_CH( HAL_SPI_CH_RX );
spiRxIdx = 0;
(void)memset(spiRxBuf, (DMA_PAD ^ 0xFF), SPI_MAX_PKT_LEN * sizeof(uint16));
HAL_DMA_ARM_CH(HAL_SPI_CH_RX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
/* Abort any pending DMA operations */
HAL_DMA_ABORT_CH( HAL_SPI_CH_TX );
HAL_DMA_ARM_CH(HAL_SPI_CH_TX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
SPI_SET_CSn_OUT();
while((!SPI_RDY_IN()) && (!spiRdyIsr) );
HAL_DMA_MAN_TRIGGER(HAL_SPI_CH_TX);
#elif !defined HAL_SPI_MASTER
#ifdef POWER_SAVING
/* Disable POWER SAVING when transmission is initiated */
CLEAR_SLEEP_MODE();
#endif
HAL_DMA_ARM_CH(HAL_SPI_CH_RX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
spiTxPkt[SPI_LEN_IDX] = len;
(void)memcpy(spiTxPkt + SPI_DAT_IDX, buf, len);
spiCalcFcs(spiTxPkt);
spiTxPkt[SPI_SOF_IDX] = SPI_SOF;
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_SPI_CH_TX);
HAL_DMA_SET_LEN(ch, SPI_PKT_LEN(spiTxPkt) + 1); /* slave DMA TX might drop the last byte */
HAL_DMA_ARM_CH(HAL_SPI_CH_TX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
SPI_SET_RDY_OUT();
#endif
return len;
}
/**************************************************************************************************
* @fn HalUARTInitSPI
*
* @brief Initialize the SPI UART Transport.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
*/
static void HalUARTInitSPI(void)
{
#if (HAL_UART_SPI == 1)
PERCFG &= ~HAL_UART_PERCFG_BIT; /* Set UART0 I/O to Alt. 1 location on P0 */
#else
PERCFG |= HAL_UART_PERCFG_BIT; /* Set UART1 I/O to Alt. 2 location on P1 */
#endif
#if defined HAL_SPI_MASTER
PxSEL |= HAL_UART_Px_SEL_M; /* SPI-Master peripheral select */
UxCSR = 0; /* Mode is SPI-Master Mode */
UxGCR = 15; /* Cfg for the max Rx/Tx baud of 2-MHz */
UxBAUD = 255;
#elif !defined HAL_SPI_MASTER
PxSEL |= HAL_UART_Px_SEL_S; /* SPI-Slave peripheral select */
UxCSR = CSR_SLAVE; /* Mode is SPI-Slave Mode */
#endif
UxUCR = UCR_FLUSH; /* Flush it */
UxGCR |= BV(5); /* Set bit order to MSB */
P2DIR &= ~P2DIR_PRIPO;
P2DIR |= HAL_UART_PRIPO;
/* Setup GPIO for interrupts by falling edge on SPI_RDY_IN */
PxIEN |= SPI_RDYIn_BIT;
PICTL |= PICTL_BIT;
SPI_CLR_RDY_OUT();
PxDIR |= SPI_RDYOut_BIT;
/* Setup Tx by DMA */
halDMADesc_t *ch = HAL_DMA_GET_DESC1234( HAL_SPI_CH_TX );
/* Abort any pending DMA operations (in case of a soft reset) */
HAL_DMA_ABORT_CH( HAL_SPI_CH_TX );
/* The start address of the destination */
HAL_DMA_SET_DEST( ch, DMA_UxDBUF );
/* Using the length field to determine how many bytes to transfer */
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
/* One byte is transferred each time */
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_BYTE );
/* The bytes are transferred 1-by-1 on Tx Complete trigger */
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_TX );
/* The source address is incremented by 1 byte after each transfer */
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_1 );
HAL_DMA_SET_SOURCE( ch, spiTxPkt );
/* The destination address is constant - the Tx Data Buffer */
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_0 );
/* The DMA Tx done is serviced by ISR */
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_ENABLE );
/* Xfer all 8 bits of a byte xfer */
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
/* DMA has highest priority for memory access */
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH );
/* Setup Rx by DMA */
ch = HAL_DMA_GET_DESC1234( HAL_SPI_CH_RX );
/* Abort any pending DMA operations (in case of a soft reset) */
HAL_DMA_ABORT_CH( HAL_SPI_CH_RX );
/* The start address of the source */
HAL_DMA_SET_SOURCE( ch, DMA_UxDBUF );
/* Using the length field to determine how many bytes to transfer */
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
/* The trick is to cfg DMA to xfer 2 bytes for every 1 byte of Rx.
* The byte after the Rx Data Buffer is the Baud Cfg Register,
* which always has a known value. So init Rx buffer to inverse of that
* known value. DMA word xfer will flip the bytes, so every valid Rx byte
* in the Rx buffer will be preceded by a DMA_PAD char equal to the
* Baud Cfg Register value.
*/
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_WORD );
/* The bytes are transferred 1-by-1 on Rx Complete trigger */
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE_REPEATED );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_RX );
/* The source address is constant - the Rx Data Buffer */
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_0 );
/* The destination address is incremented by 1 word after each transfer */
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_1 );
HAL_DMA_SET_DEST( ch, spiRxBuf );
HAL_DMA_SET_LEN( ch, SPI_MAX_PKT_LEN );
/* The DMA is to be polled and shall not issue an IRQ upon completion */
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_DISABLE );
/* Xfer all 8 bits of a byte xfer */
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
/* DMA has highest priority for memory access */
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH );
volatile uint8 dummy = *(volatile uint8 *)DMA_UxDBUF; /* Clear the DMA Rx trigger */
HAL_DMA_CLEAR_IRQ(HAL_SPI_CH_RX);
HAL_DMA_ARM_CH(HAL_SPI_CH_RX);
(void)memset(spiRxBuf, (DMA_PAD ^ 0xFF), SPI_MAX_PKT_LEN * sizeof(uint16));
}
/******************************************************************************
* @fn HalUARTInitDMA
*
* @brief Initialize the UART
*
* @param none
*
* @return none
*****************************************************************************/
static void HalUARTInitDMA(void)
{
halDMADesc_t *ch;
#if (HAL_UART_DMA == 1)
PERCFG &= ~HAL_UART_PERCFG_BIT; // Set UART0 I/O to Alt. 1 location on P0.
#else
PERCFG |= HAL_UART_PERCFG_BIT; // Set UART1 I/O to Alt. 2 location on P1.
#endif
PxSEL |= HAL_UART_Px_SEL; // Enable Peripheral control of Rx/Tx on Px. p0.2 P0.3 set peripheral //i0 setting
UxCSR = CSR_MODE; // Mode is UART Mode.
UxUCR = UCR_FLUSH; // Flush it.
P2DIR &= ~P2DIR_PRIPO; //ÓÅÏȼ¶
P2DIR |= HAL_UART_PRIPO;
if (DMA_PM)
{
// Setup GPIO for interrupts by falling edge on DMA_RDY_IN.
PxIEN |= DMA_RDYIn_BIT;
PICTL |= PICTL_BIT;
HAL_UART_DMA_CLR_RDY_OUT();
PxDIR |= DMA_RDYOut_BIT;
}
#if !HAL_UART_TX_BY_ISR
// Setup Tx by DMA.
ch = HAL_DMA_GET_DESC1234( HAL_DMA_CH_TX );
// Abort any pending DMA operations (in case of a soft reset).
HAL_DMA_ABORT_CH( HAL_DMA_CH_TX );
// The start address of the destination.
HAL_DMA_SET_DEST( ch, DMA_UxDBUF );
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
// One byte is transferred each time.
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_BYTE );
// The bytes are transferred 1-by-1 on Tx Complete trigger.
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_TX );
// The source address is incremented by 1 byte after each transfer.
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_1 );
// The destination address is constant - the Tx Data Buffer.
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_0 );
// The DMA Tx done is serviced by ISR in order to maintain full thruput.
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_ENABLE );
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH);
#endif
// Setup Rx by DMA.
ch = HAL_DMA_GET_DESC1234( HAL_DMA_CH_RX );
// Abort any pending DMA operations (in case of a soft reset).
HAL_DMA_ABORT_CH( HAL_DMA_CH_RX );
// The start address of the source.
HAL_DMA_SET_SOURCE( ch, DMA_UxDBUF );
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
/* The trick is to cfg DMA to xfer 2 bytes for every 1 byte of Rx.
* The byte after the Rx Data Buffer is the Baud Cfg Register,
* which always has a known value. So init Rx buffer to inverse of that
* known value. DMA word xfer will flip the bytes, so every valid Rx byte
* in the Rx buffer will be preceded by a DMA_PAD char equal to the
* Baud Cfg Register value.
*/
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_WORD );
// The bytes are transferred 1-by-1 on Rx Complete trigger.
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE_REPEATED );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_RX );
// The source address is constant - the Rx Data Buffer.
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_0 );
// The destination address is incremented by 1 word after each transfer.
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_1 );
HAL_DMA_SET_DEST( ch, dmaCfg.rxBuf );
HAL_DMA_SET_LEN( ch, HAL_UART_DMA_RX_MAX );
// The DMA is to be polled and shall not issue an IRQ upon completion.
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_DISABLE );
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH);
volatile uint8 dummy = *(volatile uint8 *)DMA_UxDBUF; // Clear the DMA Rx trigger.
HAL_DMA_CLEAR_IRQ(HAL_DMA_CH_RX);
HAL_DMA_ARM_CH(HAL_DMA_CH_RX);
(void)memset(dmaCfg.rxBuf, (DMA_PAD ^ 0xFF), HAL_UART_DMA_RX_MAX * sizeof(uint16));
}
/**************************************************************************************************
* @fn HalUARTWriteSPI
*
* @brief Transmit data bytes as a SPI packet.
*
* input parameters
*
* @param buf - pointer to the memory of the data bytes to send.
* @param len - the length of the data bytes to send.
*
* output parameters
*
* None.
*
* @return Zero for any error; otherwise, 'len'.
*/
static spiLen_t HalUARTWriteSPI(uint8 *buf, spiLen_t len)
{
if (spiTxLen != 0)
{
return 0;
}
if (len > SPI_MAX_DAT_LEN)
{
len = SPI_MAX_DAT_LEN;
}
spiTxLen = len;
#if defined HAL_SPI_MASTER
spiRdyIsr = 0;
spiTxPkt[SPI_LEN_IDX] = len;
(void)memcpy(spiTxPkt + SPI_DAT_IDX, buf, len);
spiCalcFcs(spiTxPkt);
spiTxPkt[SPI_SOF_IDX] = SPI_SOF;
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_SPI_CH_TX);
HAL_DMA_SET_LEN(ch, SPI_PKT_LEN(spiTxPkt)); /* DMA TX might need padding */
/* Abort any pending DMA operations */
HAL_DMA_ABORT_CH( HAL_SPI_CH_RX );
spiRxIdx = 0;
(void)memset(spiRxBuf, (DMA_PAD ^ 0xFF), SPI_MAX_PKT_LEN * sizeof(uint16));
HAL_DMA_ARM_CH(HAL_SPI_CH_RX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
/* Abort any pending DMA operations */
HAL_DMA_ABORT_CH( HAL_SPI_CH_TX );
HAL_DMA_ARM_CH(HAL_SPI_CH_TX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
SPI_SET_CSn_OUT();
while((!SPI_RDY_IN()) && (!spiRdyIsr) );
HAL_DMA_MAN_TRIGGER(HAL_SPI_CH_TX);
#elif !defined HAL_SPI_MASTER
#ifdef POWER_SAVING
/* Disable POWER SAVING when transmission is initiated */
CLEAR_SLEEP_MODE();
#endif
SPI_CLR_RDY_OUT();
HAL_DMA_ARM_CH(HAL_SPI_CH_RX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
if ( SPI_RDY_IN() )
{
SPI_SET_RDY_OUT();
}
spiTxPkt[SPI_LEN_IDX] = len;
(void)memcpy(spiTxPkt + SPI_DAT_IDX, buf, len);
spiCalcFcs(spiTxPkt);
spiTxPkt[SPI_SOF_IDX] = SPI_SOF;
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_SPI_CH_TX);
HAL_DMA_SET_LEN(ch, SPI_PKT_LEN(spiTxPkt) + 1); /* slave DMA TX might drop the last byte */
HAL_DMA_ARM_CH(HAL_SPI_CH_TX);
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
asm("NOP"); asm("NOP"); asm("NOP"); asm("NOP");
SPI_SET_RDY_OUT();
#endif
return len;
}
/**************************************************************************************************
* @fn HalSpiDmaInit
*
* @brief This function initializes the DMA for the SPI driver.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
static void HalSpiDmaInit(void)
{
halDMADesc_t *ch;
// Setup Tx by DMA
ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_TX);
// The start address of the source and destination.
HAL_DMA_SET_SOURCE(ch, halSpiBuf);
HAL_DMA_SET_DEST(ch, DMA_UDBUF);
// Transfer the first byte + the number of bytes indicated by the first byte + 2 more bytes.
HAL_DMA_SET_VLEN(ch, HAL_DMA_VLEN_1_P_VALOFFIRST_P_2);
HAL_DMA_SET_LEN(ch, HAL_SPI_BUF_LEN);
// One byte is transferred each time.
HAL_DMA_SET_WORD_SIZE(ch, HAL_DMA_WORDSIZE_BYTE);
// The bytes are transferred 1-by-1 on Tx Complete trigger.
HAL_DMA_SET_TRIG_MODE(ch, HAL_DMA_TMODE_SINGLE);
HAL_DMA_SET_TRIG_SRC(ch, DMATRIG_TX);
// The source address is incremented by 1 byte after each transfer.
HAL_DMA_SET_SRC_INC(ch, HAL_DMA_SRCINC_1);
// The destination address is constant - the Tx Data Buffer.
HAL_DMA_SET_DST_INC(ch, HAL_DMA_DSTINC_0);
// The DMA shall issue an IRQ upon completion.
HAL_DMA_SET_IRQ(ch, HAL_DMA_IRQMASK_ENABLE);
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8(ch, HAL_DMA_M8_USE_8_BITS);
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY(ch, HAL_DMA_PRI_HIGH);
//////////////////////////////////////////////////////////////////////////////
// Setup Rx by DMA.
ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_RX);
// The start address of the source and destination.
HAL_DMA_SET_SOURCE(ch, DMA_UDBUF);
HAL_DMA_SET_DEST(ch, halSpiBuf);
// Transfer the first byte + the number of bytes indicated by the first byte + 2 more bytes.
HAL_DMA_SET_VLEN(ch, HAL_DMA_VLEN_1_P_VALOFFIRST_P_2);
HAL_DMA_SET_LEN(ch, HAL_SPI_BUF_LEN);
HAL_DMA_SET_WORD_SIZE(ch, HAL_DMA_WORDSIZE_BYTE);
// The bytes are transferred 1-by-1 on Rx Complete trigger.
HAL_DMA_SET_TRIG_MODE(ch, HAL_DMA_TMODE_SINGLE);
HAL_DMA_SET_TRIG_SRC(ch, DMATRIG_RX);
// The source address is constant - the Rx Data Buffer.
HAL_DMA_SET_SRC_INC(ch, HAL_DMA_SRCINC_0);
// The destination address is incremented by 1 byte after each transfer.
HAL_DMA_SET_DST_INC(ch, HAL_DMA_DSTINC_1);
// The DMA shall issue an IRQ upon completion.
HAL_DMA_SET_IRQ(ch, HAL_DMA_IRQMASK_ENABLE);
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8(ch, HAL_DMA_M8_USE_8_BITS);
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY(ch, HAL_DMA_PRI_HIGH);
}
/******************************************************************************
* @fn HalUARTPollDMA
*
* @brief Poll a USART module implemented by DMA.
*
* @param none
*
* @return none
*****************************************************************************/
static void HalUARTPollDMA(void)
{
uint16 cnt = 0;
uint8 evt = 0;
if (HAL_UART_DMA_NEW_RX_BYTE(dmaCfg.rxHead))
{
rxIdx_t tail = findTail();
// If the DMA has transferred in more Rx bytes, reset the Rx idle timer.
if (dmaCfg.rxTail != tail)
{
dmaCfg.rxTail = tail;
// Re-sync the shadow on any 1st byte(s) received.
if (dmaCfg.rxTick == 0)
{
dmaCfg.rxShdw = ST0;
}
dmaCfg.rxTick = HAL_UART_DMA_IDLE;
}
else if (dmaCfg.rxTick)
{
// Use the LSB of the sleep timer (ST0 must be read first anyway).
uint8 decr = ST0 - dmaCfg.rxShdw;
if (dmaCfg.rxTick > decr)
{
dmaCfg.rxTick -= decr;
dmaCfg.rxShdw = ST0;
}
else
{
dmaCfg.rxTick = 0;
}
}
cnt = HalUARTRxAvailDMA();
}
else
{
dmaCfg.rxTick = 0;
}
if (cnt >= HAL_UART_DMA_FULL)
{
evt = HAL_UART_RX_FULL;
}
else if (cnt >= HAL_UART_DMA_HIGH)
{
evt = HAL_UART_RX_ABOUT_FULL;
PxOUT |= HAL_UART_Px_RTS; // Disable Rx flow.
}
else if (cnt && !dmaCfg.rxTick)
{
evt = HAL_UART_RX_TIMEOUT;
}
if (dmaCfg.txMT)
{
dmaCfg.txMT = FALSE;
evt |= HAL_UART_TX_EMPTY;
}
if (dmaCfg.txShdwValid)
{
uint8 decr = ST0;
decr -= dmaCfg.txShdw;
if (decr > dmaCfg.txTick)
{
// No protection for txShdwValid is required
// because while the shadow was valid, DMA ISR cannot be triggered
// to cause concurrent access to this variable.
dmaCfg.txShdwValid = FALSE;
}
}
if (dmaCfg.txDMAPending && !dmaCfg.txShdwValid)
{
// UART TX DMA is expected to be fired and enough time has lapsed since last DMA ISR
// to know that DBUF can be overwritten
halDMADesc_t *ch = HAL_DMA_GET_DESC1234(HAL_DMA_CH_TX);
halIntState_t intState;
// Clear the DMA pending flag
dmaCfg.txDMAPending = FALSE;
HAL_DMA_SET_SOURCE(ch, dmaCfg.txBuf[dmaCfg.txSel]);
HAL_DMA_SET_LEN(ch, dmaCfg.txIdx[dmaCfg.txSel]);
dmaCfg.txSel ^= 1;
HAL_ENTER_CRITICAL_SECTION(intState);
HAL_DMA_ARM_CH(HAL_DMA_CH_TX);
do
{
asm("NOP");
} while (!HAL_DMA_CH_ARMED(HAL_DMA_CH_TX));
HAL_DMA_CLEAR_IRQ(HAL_DMA_CH_TX);
HAL_DMA_MAN_TRIGGER(HAL_DMA_CH_TX);
HAL_EXIT_CRITICAL_SECTION(intState);
}
else
{
halIntState_t his;
HAL_ENTER_CRITICAL_SECTION(his);
if ((dmaCfg.txIdx[dmaCfg.txSel] != 0) && !HAL_DMA_CH_ARMED(HAL_DMA_CH_TX)
&& !HAL_DMA_CHECK_IRQ(HAL_DMA_CH_TX))
{
HAL_EXIT_CRITICAL_SECTION(his);
HalUARTIsrDMA();
}
else
{
HAL_EXIT_CRITICAL_SECTION(his);
}
}
if (evt && (dmaCfg.uartCB != NULL))
{
dmaCfg.uartCB(HAL_UART_DMA-1, evt);
}
}
/******************************************************************************
* @fn HalUARTInitDMA
*
* @brief Initialize the UART
*
* @param none
*
* @return none
*****************************************************************************/
static void HalUARTInitDMA(void)
{
halDMADesc_t *ch;
P2DIR &= ~P2DIR_PRIPO;
P2DIR |= HAL_UART_PRIPO;
#if (HAL_UART_DMA == 1)
PERCFG &= ~HAL_UART_PERCFG_BIT; // Set UART0 I/O to Alt. 1 location on P0.
#else
PERCFG |= HAL_UART_PERCFG_BIT; // Set UART1 I/O to Alt. 2 location on P1.
#endif
PxSEL |= HAL_UART_Px_RX_TX; // Enable Tx and Rx on P1.
ADCCFG &= ~HAL_UART_Px_RX_TX; // Make sure ADC doesnt use this.
UxCSR = CSR_MODE; // Mode is UART Mode.
UxUCR = UCR_FLUSH; // Flush it.
// Setup Tx by DMA.
ch = HAL_DMA_GET_DESC1234( HAL_DMA_CH_TX );
// The start address of the destination.
HAL_DMA_SET_DEST( ch, DMA_UDBUF );
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
// One byte is transferred each time.
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_BYTE );
// The bytes are transferred 1-by-1 on Tx Complete trigger.
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_TX );
// The source address is incremented by 1 byte after each transfer.
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_1 );
// The destination address is constant - the Tx Data Buffer.
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_0 );
// The DMA Tx done is serviced by ISR in order to maintain full thruput.
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_ENABLE );
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH );
// Setup Rx by DMA.
ch = HAL_DMA_GET_DESC1234( HAL_DMA_CH_RX );
// The start address of the source.
HAL_DMA_SET_SOURCE( ch, DMA_UDBUF );
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN( ch, HAL_DMA_VLEN_USE_LEN );
/* The trick is to cfg DMA to xfer 2 bytes for every 1 byte of Rx.
* The byte after the Rx Data Buffer is the Baud Cfg Register,
* which always has a known value. So init Rx buffer to inverse of that
* known value. DMA word xfer will flip the bytes, so every valid Rx byte
* in the Rx buffer will be preceded by a DMA_PAD char equal to the
* Baud Cfg Register value.
*/
HAL_DMA_SET_WORD_SIZE( ch, HAL_DMA_WORDSIZE_WORD );
// The bytes are transferred 1-by-1 on Rx Complete trigger.
HAL_DMA_SET_TRIG_MODE( ch, HAL_DMA_TMODE_SINGLE_REPEATED );
HAL_DMA_SET_TRIG_SRC( ch, DMATRIG_RX );
// The source address is constant - the Rx Data Buffer.
HAL_DMA_SET_SRC_INC( ch, HAL_DMA_SRCINC_0 );
// The destination address is incremented by 1 word after each transfer.
HAL_DMA_SET_DST_INC( ch, HAL_DMA_DSTINC_1 );
HAL_DMA_SET_DEST( ch, dmaCfg.rxBuf );
HAL_DMA_SET_LEN( ch, HAL_UART_DMA_RX_MAX );
// The DMA is to be polled and shall not issue an IRQ upon completion.
HAL_DMA_SET_IRQ( ch, HAL_DMA_IRQMASK_DISABLE );
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8( ch, HAL_DMA_M8_USE_8_BITS );
// DMA has highest priority for memory access.
HAL_DMA_SET_PRIORITY( ch, HAL_DMA_PRI_HIGH );
}
/******************************************************************************
* @fn HalIrGenInitNec
*
* @brief Initialize driver
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
*
*/
void HalIrGenInitNec(void)
{
// Set TICKSPD:4M
CLKCONCMD &= ~HAL_IRGEN_CLKCON_TICKSPD_MASK;
CLKCONCMD |= HAL_IRGEN_TICKSPD_4MHZ;
// Select port direction to output: P1.1 set output(1)
P1DIR |= HAL_IRGEN_P1SEL_PORT;
// Initially clear the port so that there will be no conflict
P1 &= ~HAL_IRGEN_P1SEL_PORT;
// Select port function to peripheral: P1.1 set Peripherial(1)
P1SEL |= HAL_IRGEN_P1SEL_PORT;
// Select alternative 2 location for T1 CH1 output (P1.1)
PERCFG |= HAL_IRGEN_PERCFG_T1CFG;
// -- set up bit signal generation timer --
// -- run timer once to make sure output is deactivated
// Halt timer 1:Suspended
T1CTL = HAL_IRGEN_T1CTL_MODE_SUSPEND;
// Set up timer 1 channel 0 to compare mode 4
T1CCTL0 = HAL_IRGEN_TxCCTLx_CMP_CLR_SET | HAL_IRGEN_TxCCTLx_MODE_COMPARE;
// Set up timer 1 channel 1 to compare mode 4
T1CCTL1 = HAL_IRGEN_TxCCTLx_CMP_CLR_SET | HAL_IRGEN_TxCCTLx_MODE_COMPARE;
// Run one timer 1 until output is pulled low.
// T1CNTL = 0; // Set up timer comparators for single carrier pulse output
T1CC0L = 2;
T1CC0H = 0;
T1CC1L = 1;
T1CC1H = 0;
// Clear timer 1
// this will activate the output pin so start timer immediately.
T1CNTL = 0;
// Start timer 1: Set Modulo Mode
T1CTL = HAL_IRGEN_BIT_TIMING_PRESCALER_DIV1 | HAL_IRGEN_T1CTL_MODE_MODULO;
// Wait till the single bit is cleared
while (T1CNTL == 0);
// Stop timer 1
T1CTL = HAL_IRGEN_T1CTL_MODE_SUSPEND;
#ifdef HAL_IRGEN_CARRIER
// -- set up carrier signal generation timer --
// Clear counter and halt the timer
T3CTL = HAL_IRGEN_T3CTL_CLR;
// Set up timer 3 channel 0 to compare mode 4
T3CCTL0 = HAL_IRGEN_TxCCTLx_CMP_CLR_SET | HAL_IRGEN_TxCCTLx_MODE_COMPARE;
// Set up timer 3 channel 1 to compare mode 4
T3CCTL1 = HAL_IRGEN_TxCCTLx_CMP_CLR_SET | HAL_IRGEN_TxCCTLx_MODE_COMPARE;
// Configure 38kHz carrier with 33% duty cycle
T3CC0 = HAL_IRGEN_NEC_CARRIER_DUTY_CYCLE;
T3CC1 = HAL_IRGEN_NEC_CARRIER_ACTIVE_PER;
// Combine carrier signal (Timer 1 CH 1 and Timer 3 CH 1 output)
IRCTL |= 1;
#endif // HAL_IRGEN_CARRIER
// -- Configure DMA --
// Select proper DMA channel descriptor structure
// Set up DMA channel for CC0
#if HAL_IRGEN_DMA_CH_CC0 == 0
pDmaDescCc0 = HAL_DMA_GET_DESC0();
#else
pDmaDescCc0 = HAL_DMA_GET_DESC1234(HAL_IRGEN_DMA_CH_CC0);
#endif
// The start address of the destination.
HAL_DMA_SET_DEST(pDmaDescCc0, HAL_IRGEN_T1CC0L_ADDR);
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN(pDmaDescCc0, HAL_DMA_VLEN_USE_LEN);
// Two bytes are transferred each time.
HAL_DMA_SET_WORD_SIZE(pDmaDescCc0, HAL_DMA_WORDSIZE_WORD);
// One word is transferred each time .
HAL_DMA_SET_TRIG_MODE(pDmaDescCc0, HAL_DMA_TMODE_SINGLE);
// Timer 1 channel 1 trigger DMA xfer
HAL_DMA_SET_TRIG_SRC(pDmaDescCc0, HAL_DMA_TRIG_T1_CH1);
// The source address is incremented by 1 word after each transfer.
HAL_DMA_SET_SRC_INC(pDmaDescCc0, HAL_DMA_SRCINC_1);
// The destination address is constant - T1CC0.
HAL_DMA_SET_DST_INC(pDmaDescCc0, HAL_DMA_DSTINC_0);
// IRQ handler is set up to tigger on CC1
HAL_DMA_SET_IRQ(pDmaDescCc0, HAL_DMA_IRQMASK_DISABLE);
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8(pDmaDescCc0, HAL_DMA_M8_USE_8_BITS);
// Set highest priority
HAL_DMA_SET_PRIORITY(pDmaDescCc0, HAL_DMA_PRI_HIGH);
// Set source data stream
HAL_DMA_SET_SOURCE(pDmaDescCc0, &halIrGenCc0Buf[0]);
// Set up DMA channel for CC1
#if HAL_IRGEN_DMA_CH_CC1 == 0
pDmaDescCc1 = HAL_DMA_GET_DESC0();
#else
pDmaDescCc1 = HAL_DMA_GET_DESC1234(HAL_IRGEN_DMA_CH_CC1);
#endif
// The start address of the destination.
HAL_DMA_SET_DEST(pDmaDescCc1, HAL_IRGEN_T1CC1L_ADDR);
// Using the length field to determine how many bytes to transfer.
HAL_DMA_SET_VLEN(pDmaDescCc1, HAL_DMA_VLEN_USE_LEN);
// Two bytes are transferred each time.
HAL_DMA_SET_WORD_SIZE(pDmaDescCc1, HAL_DMA_WORDSIZE_WORD);
// One word is transferred each time
HAL_DMA_SET_TRIG_MODE( pDmaDescCc1, HAL_DMA_TMODE_SINGLE );
// Timer 1 channel 1 trigger
HAL_DMA_SET_TRIG_SRC(pDmaDescCc1, HAL_DMA_TRIG_T1_CH1);
// The source address is not incremented since active periode is constant.
HAL_DMA_SET_SRC_INC(pDmaDescCc1, HAL_DMA_SRCINC_0);
// The destination address is constant - T1CC1.
HAL_DMA_SET_DST_INC(pDmaDescCc1, HAL_DMA_DSTINC_0);
// IRQ handler is set up so that sleep enable/disable can be determined.
HAL_DMA_SET_IRQ(pDmaDescCc1, HAL_DMA_IRQMASK_ENABLE);
// Xfer all 8 bits of a byte xfer.
HAL_DMA_SET_M8(pDmaDescCc1, HAL_DMA_M8_USE_8_BITS);
// Set highest priority
HAL_DMA_SET_PRIORITY(pDmaDescCc1, HAL_DMA_PRI_HIGH);
// Set source data stream. It is always constant.
HAL_DMA_SET_SOURCE(pDmaDescCc1, &halIrGenCc1);
// Timer is not running
halIrGenTimerRunning = FALSE;
}