acpi_status acpi_ev_install_region_handlers(void)
{
acpi_status status;
u32 i;
ACPI_FUNCTION_TRACE(ev_install_region_handlers);
status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
if (ACPI_FAILURE(status)) {
return_ACPI_STATUS(status);
}
/*
* All address spaces (PCI Config, EC, SMBus) are scope dependent and
* registration must occur for a specific device.
*
* In the case of the system memory and IO address spaces there is
* currently no device associated with the address space. For these we
* use the root.
*
* We install the default PCI config space handler at the root so that
* this space is immediately available even though the we have not
* enumerated all the PCI Root Buses yet. This is to conform to the ACPI
* specification which states that the PCI config space must be always
* available -- even though we are nowhere near ready to find the PCI root
* buses at this point.
*
* NOTE: We ignore AE_ALREADY_EXISTS because this means that a handler
* has already been installed (via acpi_install_address_space_handler).
* Similar for AE_SAME_HANDLER.
*/
for (i = 0; i < ACPI_NUM_DEFAULT_SPACES; i++) {
status = acpi_ev_install_space_handler(acpi_gbl_root_node,
acpi_gbl_default_address_spaces
[i],
ACPI_DEFAULT_HANDLER,
NULL, NULL);
switch (status) {
case AE_OK:
case AE_SAME_HANDLER:
case AE_ALREADY_EXISTS:
/* These exceptions are all OK */
status = AE_OK;
break;
default:
goto unlock_and_exit;
}
}
unlock_and_exit:
(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
return_ACPI_STATUS(status);
}
/*******************************************************************************
*
* FUNCTION: acpi_install_address_space_handler
*
* PARAMETERS: Device - Handle for the device
* space_id - The address space ID
* Handler - Address of the handler
* Setup - Address of the setup function
* Context - Value passed to the handler on each access
*
* RETURN: Status
*
* DESCRIPTION: Install a handler for all op_regions of a given space_id.
*
******************************************************************************/
acpi_status
acpi_install_address_space_handler(acpi_handle device,
acpi_adr_space_type space_id,
acpi_adr_space_handler handler,
acpi_adr_space_setup setup, void *context)
{
struct acpi_namespace_node *node;
acpi_status status;
ACPI_FUNCTION_TRACE(acpi_install_address_space_handler);
/* Parameter validation */
if (!device) {
return_ACPI_STATUS(AE_BAD_PARAMETER);
}
status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
if (ACPI_FAILURE(status)) {
return_ACPI_STATUS(status);
}
/* Convert and validate the device handle */
node = acpi_ns_map_handle_to_node(device);
if (!node) {
status = AE_BAD_PARAMETER;
goto unlock_and_exit;
}
/* Install the handler for all Regions for this Space ID */
status =
acpi_ev_install_space_handler(node, space_id, handler, setup,
context);
if (ACPI_FAILURE(status)) {
goto unlock_and_exit;
}
/* Run all _REG methods for this address space */
status = acpi_ev_execute_reg_methods(node, space_id);
unlock_and_exit:
(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
return_ACPI_STATUS(status);
}
/*******************************************************************************
*
* FUNCTION: acpi_install_address_space_handler
*
* PARAMETERS: device - Handle for the device
* space_id - The address space ID
* handler - Address of the handler
* setup - Address of the setup function
* context - Value passed to the handler on each access
*
* RETURN: Status
*
* DESCRIPTION: Install a handler for all op_regions of a given space_id.
*
* NOTE: This function should only be called after acpi_enable_subsystem has
* been called. This is because any _REG methods associated with the Space ID
* are executed here, and these methods can only be safely executed after
* the default handlers have been installed and the hardware has been
* initialized (via acpi_enable_subsystem.)
*
******************************************************************************/
acpi_status
acpi_install_address_space_handler(acpi_handle device,
acpi_adr_space_type space_id,
acpi_adr_space_handler handler,
acpi_adr_space_setup setup, void *context)
{
struct acpi_namespace_node *node;
acpi_status status;
ACPI_FUNCTION_TRACE(acpi_install_address_space_handler);
/* Parameter validation */
if (!device) {
return_ACPI_STATUS(AE_BAD_PARAMETER);
}
status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
if (ACPI_FAILURE(status)) {
return_ACPI_STATUS(status);
}
/* Convert and validate the device handle */
node = acpi_ns_validate_handle(device);
if (!node) {
status = AE_BAD_PARAMETER;
goto unlock_and_exit;
}
/* Install the handler for all Regions for this Space ID */
status =
acpi_ev_install_space_handler(node, space_id, handler, setup,
context);
if (ACPI_FAILURE(status)) {
goto unlock_and_exit;
}
/*
* For the default space_IDs, (the IDs for which there are default region handlers
* installed) Only execute the _REG methods if the global initialization _REG
* methods have already been run (via acpi_initialize_objects). In other words,
* we will defer the execution of the _REG methods for these space_IDs until
* execution of acpi_initialize_objects. This is done because we need the handlers
* for the default spaces (mem/io/pci/table) to be installed before we can run
* any control methods (or _REG methods). There is known BIOS code that depends
* on this.
*
* For all other space_IDs, we can safely execute the _REG methods immediately.
* This means that for IDs like embedded_controller, this function should be called
* only after acpi_enable_subsystem has been called.
*/
switch (space_id) {
case ACPI_ADR_SPACE_SYSTEM_MEMORY:
case ACPI_ADR_SPACE_SYSTEM_IO:
case ACPI_ADR_SPACE_PCI_CONFIG:
case ACPI_ADR_SPACE_DATA_TABLE:
if (!acpi_gbl_reg_methods_executed) {
/* We will defer execution of the _REG methods for this space */
goto unlock_and_exit;
}
break;
default:
break;
}
/* Run all _REG methods for this address space */
status = acpi_ev_execute_reg_methods(node, space_id);
unlock_and_exit:
(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
return_ACPI_STATUS(status);
}
