static void
__prestart()
{
int ii, i1, i2, i3;
int ret;
/* Clear some global variables etc for a clean start */
*(rol->nevents) = 0;
event_number = 0;
tiEnableVXSSignals();
#ifdef POLLING_MODE
CTRIGRSS(TIPRIMARY, TIR_SOURCE, usrtrig, usrtrig_done);
#else
CTRIGRSA(TIPRIMARY, TIR_SOURCE, usrtrig, usrtrig_done);
#endif
printf(">>>>>>>>>> next_block_level = %d, block_level = %d, use next_block_level\n",next_block_level,block_level);
block_level = next_block_level;
/**************************************************************************/
/* setting TI busy conditions, based on boards found in Download */
/* tiInit() does nothing for busy, tiConfig() sets fiber, we set the rest */
/* NOTE: if ti is busy, it will not send trigger enable over fiber, since */
/* it is the same fiber and busy has higher priority */
#ifndef TI_SLAVE
vmeBusLock();
tiSetBusySource(TI_BUSY_LOOPBACK,0);
/*tiSetBusySource(TI_BUSY_FP,0);*/
vmeBusUnlock();
#endif
#ifdef USE_PRAD
#ifdef USE_V767
vmeBusLock();
v767Clear(0);
v767Status(0, 0, 0);
vmeBusUnlock();
#endif
#ifdef USE_V1190
vmeBusLock();
tdc1190Clear(0);
tdc1190Status(0);
vmeBusUnlock();
#endif
/*if(nfadc>0)*/
{
printf("Set BUSY from FP for FASTBUS\n");
vmeBusLock();
tiSetBusySource(TI_BUSY_FP, 0);
vmeBusUnlock();
}
#endif
/* USER code here */
/******************/
vmeBusLock();
tiIntDisable();
vmeBusUnlock();
/* master and standalone crates, NOT slave */
#ifndef TI_SLAVE
sleep(1);
vmeBusLock();
tiSyncReset(1);
vmeBusUnlock();
sleep(1);
vmeBusLock();
tiSyncReset(1);
vmeBusUnlock();
sleep(1);
vmeBusLock();
ret = tiGetSyncResetRequest();
vmeBusUnlock();
if(ret)
{
printf("ERROR: syncrequest still ON after tiSyncReset(); trying again\n");
sleep(1);
vmeBusLock();
tiSyncReset(1);
vmeBusUnlock();
sleep(1);
}
vmeBusLock();
ret = tiGetSyncResetRequest();
vmeBusUnlock();
if(ret)
{
printf("ERROR: syncrequest still ON after tiSyncReset(); try 'tcpClient <rocname> tiSyncReset'\n");
}
else
{
printf("INFO: syncrequest is OFF now\n");
}
/*
printf("holdoff rule 1 set to %d\n",tiGetTriggerHoldoff(1));
printf("holdoff rule 2 set to %d\n",tiGetTriggerHoldoff(2));
*/
#endif
/* set block level in all boards where it is needed;
it will overwrite any previous block level settings */
#ifdef TI_SLAVE /* assume that for master and standalone TIs block level is set from config file */
vmeBusLock();
tiSetBlockLevel(block_level);
vmeBusUnlock();
#endif
#ifdef USE_V1190
tdc1190SetBLTEventNumber(0, block_level);
#endif
vmeBusLock();
tdc1190Status(0);
vmeBusUnlock();
#ifdef EVENT_CYCLE
event_count = 0;
#endif
vmeBusLock();
printf("TISTATUS 1\n");
tiStatus(1);
vmeBusUnlock();
vmeBusLock();
ti_usetrg(0);
tiSetTriggerSource(TI_TRIGGER_PULSER);
// ti_usetrg(TRG_TOTALSUM);
// tiSetInputPrescale(5, 3);
vmeBusUnlock();
vmeBusLock();
printf("TISTATUS 2\n");
tiStatus(1);
vmeBusUnlock();
printf("INFO: Prestart1 Executed\n");fflush(stdout);
*(rol->nevents) = 0;
rol->recNb = 0;
return;
}
int
main(int argc, char *argv[]) {
int stat;
printf("\nJLAB vfTDC Tests\n");
printf("----------------------------\n");
/* remexSetCmsgServer("dafarm28"); */
/* remexInit(NULL,1); */
vmeOpenDefaultWindows();
/* Setup Address and data modes for DMA transfers
*
* vmeDmaConfig(addrType, dataType, sstMode);
*
* addrType = 0 (A16) 1 (A24) 2 (A32)
* dataType = 0 (D16) 1 (D32) 2 (BLK32) 3 (MBLK) 4 (2eVME) 5 (2eSST)
* sstMode = 0 (SST160) 1 (SST267) 2 (SST320)
*/
vmeDmaConfig(2,5,1);
/* INIT dmaPList */
dmaPFreeAll();
vmeIN = dmaPCreate("vmeIN",10244,500,0);
vmeOUT = dmaPCreate("vmeOUT",0,0,0);
dmaPStatsAll();
dmaPReInitAll();
/* gefVmeSetDebugFlags(vmeHdl,0x0); */
/* Set the TI structure pointer */
/* tiInit((2<<19),TI_READOUT_EXT_POLL,0); */
tiA32Base=0x08000000;
if(tiInit(0,TI_READOUT_EXT_POLL,0)!=OK)
goto CLOSE;
tiCheckAddresses();
tiSetSyncEventInterval(10);
tiSetEventFormat(3);
char mySN[20];
printf("0x%08x\n",tiGetSerialNumber((char **)&mySN));
printf("mySN = %s\n",mySN);
#ifndef DO_READOUT
tiDisableDataReadout();
tiDisableA32();
#endif
tiLoadTriggerTable(0);
tiSetTriggerHoldoff(1,4,0);
tiSetTriggerHoldoff(2,4,0);
tiSetPrescale(0);
tiSetBlockLevel(BLOCKLEVEL);
stat = tiIntConnect(TI_INT_VEC, mytiISR, 0);
if (stat != OK)
{
printf("ERROR: tiIntConnect failed \n");
goto CLOSE;
}
else
{
printf("INFO: Attached TI Interrupt\n");
}
/* tiSetTriggerSource(TI_TRIGGER_TSINPUTS); */
tiSetTriggerSource(TI_TRIGGER_PULSER);
tiEnableTSInput(0x1);
/* tiSetFPInput(0x0); */
/* tiSetGenInput(0xffff); */
/* tiSetGTPInput(0x0); */
/* tiSetBusySource(TI_BUSY_LOOPBACK,1); */
tiSetBlockBufferLevel(1);
tiSetFiberDelay(1,2);
tiSetSyncDelayWidth(1,0x3f,1);
tiSetBlockLimit(10);
/*************************************************************/
/* VFTDC initialization */
/*************************************************************/
extern unsigned int vfTDCA32Base;
vfTDCA32Base=0x09000000;
vfTDCInit(14<<19, 1<<19, 1,
VFTDC_INIT_VXS_SYNCRESET |
VFTDC_INIT_VXS_TRIG |
VFTDC_INIT_VXS_CLKSRC);
vfTDCSetBlockLevel(0, BLOCKLEVEL);
vfTDCSetWindowParamters(0, 1, 250);
vfTDCStatus(0,0);
printf("Hit enter to reset stuff\n");
getchar();
tiClockReset();
taskDelay(1);
tiTrigLinkReset();
taskDelay(1);
tiEnableVXSSignals();
int again=0;
AGAIN:
taskDelay(1);
tiSyncReset(1);
taskDelay(1);
tiStatus(1);
vfTDCStatus(0,0);
printf("Hit enter to start triggers\n");
getchar();
tiIntEnable(0);
tiStatus(1);
#define SOFTTRIG
#ifdef SOFTTRIG
tiSetRandomTrigger(1,0x7);
/* taskDelay(10); */
/* tiSoftTrig(1,0x1,0x700,0); */
#endif
printf("Hit any key to Disable TID and exit.\n");
getchar();
tiStatus(1);
#ifdef SOFTTRIG
/* No more soft triggers */
/* tidSoftTrig(0x0,0x8888,0); */
tiSoftTrig(1,0,0x700,0);
tiDisableRandomTrigger();
#endif
tiIntDisable();
tiIntDisconnect();
vfTDCStatus(0,0);
if(again==1)
{
again=0;
goto AGAIN;
}
CLOSE:
dmaPFreeAll();
vmeCloseDefaultWindows();
exit(0);
}