RTIMULib is the simplest way to connect a 9-dof IMU to an embedded Linux system and obtain Kalman-filtered quaternion or Euler angle pose data. Basically, two simple funtion calls (IMUInit() and IMURead()) are pretty much all that's need to integrate RTIMULib.
Two demo programs are included - RTIMULibDemo is a GUI-based program that shows all the data being produce and also support compass calibration. RTIMULibDrive is just about the most basic program possible and can be used for performance testing filters and drivers. It can also be used as the basis of a real application quite easily.
Its prerequisites are very simple - just I2C support on the target system along with the standard build-essential (included in the Raspberry Pi Raspbian distribution by default).
RTIMULib provides a flexible framework for interfacing 9-dof IMUs to embedded Linux systems. RTIMULib currently supports the InvenSense MPU9150 single chip IMU, STM LSM9DS0 single chip IMU, Pololu Altimu and Adafruit 9-dof IMU. Support for others will follow. RTIMULib also supports multiple sensor integration fusion filters such as Kalman filters.
The instructions here are for the Raspberry Pi but RTIMULib can be use easily with other embedded systems with minor (or no changes). An abstraction layer allows RTIMULib to be used with non-Linux systems also.
Check out www.richards-tech.com for more details, updates and news.
RTIMULib is licensed under GPLv3.
Fixed the python getIMUData function.
Thanks to avishorp for the python code and Luke Heidelberger for a bug fix.
RTQF is a very highly stripped down Kalman filter that avoids matrix inversion and lot of other matrix operations. It makes a small performance difference on the Raspberry Pi but would have more impact on lower powered processors.
The single chip IMU LSM9DS0 is now working with RTIMULib. An example breakout is available from Sparkfun - https://www.sparkfun.com/products/12636.
The combination of the L3GD20H gyro and LSM303D accel/mag chip is now working. The physical configuration supported is as used on the Pololu Altimu V3 - http://www.pololu.com/product/2469. The pressure chip on the 10-dof version will be supported shortly but 9-dof is working now.
The combination of the L3GD20 and LSM303DLHC accel/mag chip is now working. The physical configuration supported is as used on the Adafruit 9-dof IMU - http://www.adafruit.com/products/1714.
A new caching strategy for the MPU-9150 seems to be achieving 1000 samples per second without fifo overflows using a 900MHz Raspberry Pi and 400kHz I2C bus. This is as reported by RTIMULibDrive with a CPU utilization of 28%. RTIMULibDemo manages 890 samples per second with the MPU-9150 set to 1000 samples per second. The driver gracefully handles this situation although there is increased delay when the application cannot handle the full sample rate.
RTIMULib can now scan for supported IMUs and configure automatically. This is the default behavior now. It handles IMUs at alternate address automatically as well (for example, it will detect an MPU-9150 at 0x68 or 0x69).
This is in a very early state and only supports the gyro sensor at the moment.
Initial release with support for MPU9150.
From a command prompt, enter:
git clone https://github.com/richards-tech/RTIMULib.git
The easiest way to connect the IMU to the Raspberry Pi is to use something like the Adafruit Pi Plate (http://www.adafruit.com/products/801) as it makes it obvious where the I2C bus 1 pins are and where to pick up 3.3V. Basically, you need to connect the I2C SDA, I2C SCL, 3.3V and GND to the IMU breakout board you are using. Take care with these connections or else disaster may follow!
Add the following two lines to /etc/modules:
i2c-bcm2708
i2c-dev
Then, comment out the following line in /etc/modprobe.d/raspi-blacklist.conf:
# blacklist i2c-bcm2708
Restart the Raspberry Pi and /dev/i2c-0 and /dev/i2c-1 should appear. It’s also useful to install the I2C tools:
sudo apt-get install i2c-tools
Then:
sudo i2cdetect -y 1
will detect any devices on /dev/i2c-1. If you have the MPU9150 wired up, you should see it at address 0x68. This is the default address expected by the demo programs. If it is at 0x69, the address expected by the demo programs will need to be changed (there's a settings file for doing things like that so it's easy to do).
By default, the I2C devices are owned by root. To fix this, reate a file /etc/udev/rules.d/90-i2c.rules and add the line:
KERNEL=="i2c-[0-7]",MODE="0666"
The Raspberry Pi will need to be rebooted to implement this change.
Another thing worth doing is to change the I2C bus speed to 400KHz. At the standard 100KHz, the sample rate tops out at around 230 samples per second. With the change, it should be possible to get over 400 samples per second.
To enable 400kHz operation, create a file /etc/modprobe.d/i2c.conf and add the line:
options i2c_bcm2708 baudrate=400000
Simplest thing is then to reboot to make this change.
The I2C bus should now be ready for operation.
RTIMULibDrive is a simple command line program that shows how simple it is to use RTIMULib. Assuming the I2C bus has been enabled, just go to the RTIMULibDrive directory and enter:
make
sudo make install
You should be able to run the program just by entering RTIMULibDrive. It will try to auto detect the connected IMU If all is well, you should see a line showing the sample rate and the current Euler angles. This is updated 10 times per second, regardless of the sensor sample rate. By default, the driver runs at 50 samples per second in most cases. So, you should see the sample rate indicating around 50 samples per second. The sample rate can be changed by editing the .ini file entry for the appropriate IMU type.
The displayed pose shows the roll, pitch and yaw seen by the IMU. Using an aircraft analogy, the roll axis points from the pilot towards the nose, the pitch axis points from the pilot along the right wing and the yaw axis points from the pilot down towards the ground. Right wing down is a positive roll, nose up is a positive pitch and clockwise rotation is a positive yaw.
Various parameters can be changed by editing the RTIMULib.ini file. These are described later.
Take a look at RTIMULibDrive.cpp. Quite a few of the code lines are just to calculate rates and display outputs!
One thing you may notice is that the yaw isn't too accurate, especially at non zero pitch and roll. This is because the compass has not been calibrated. RTIMULibDemo can be used to do that.
###Compile and Run the RTIMULibDemo Program
RTIMULibDemo is a Qt-based program (Qt is used to supply the GUI). So, do the following:
sudo apt-get install libqt4-dev
This will install the libraries and utilities that Qt needs.
Then, go to the RTIMULibDemo directory and enter:
qmake
make
sudo make install
To run the program, the Raspberry Pi needs to be running the desktop. To do this (if it isn't already), enter:
startx
Then open a command window and enter:
RTIMULibDemo
You should see the GUI pop up and, if everything is ok, it will start displaying data from the IMU and the output of the Kalman filter. If the MPU9150 is at the alternate address, you'll need to edit the RTIMULib.ini file that RTIMULibDemo generated and restart the program.
To calibrate the compass, click on the "Calibrate compass" tab. A new dialog will pop up showing the maximum and minimum readings seen from the magnetometers. You need to waggle the IMU around, ensuring that each axis (roll, pitch and yaw) point straight down and also straight up at some point. You need to do this in an area clear of magnetic fields otherwise the results will be distorted. Eventually, the readings will stop changing meaning that the real max and min values have been obtained. Click on "Ok" to save the values to the RTIMULib.ini file. Provided this .ini file is used in future (it just has to be in the current directory when RTIMULibDemo is run), the calibration will not have to be repeated. Now that RTIMULibDemo is using calibrated magnetometers, the yaw should be much more reliable.
The .ini file created by RTIMULibDemo can also be used by RTIMULibDrive - just run RTIMULibDrive in the same directory and it will pick up the compass calibration data.
At the moment, gyro bias is calculated during the first 5 seconds of operation. If the IMU chip is moved during this period, the bias may be calculated incorrectly and the app will need to be restarted. The effectiveness of the gyro bias compensation can be monitored using RTIMULibDemo. If the IMU chip is not in motion, the gyro rates should be close to 0 (usually around 0.001 radians per second).
By default, RTIMULib.ini is created in the working directory. This can be easily edited and the file contains extensive comments for the settings of every supported IMU type.
All of the platform-specific code is in the following files:
RTIMULib/RTIMUHal.h
RTIMULib/RTIMUHal.cpp
RTIMULib/RTIMUSettings.h
RTIMULib/RTIMUSettings.cpp
Changes to I2C code on Linux systems should only involve changes to RTIMUHal. RTIMUSettings uses the Linux file system so, if this is not present, this code would also have to modified to load and store configuration data from somewhere else.
RTIMUSettings would also need to be modified if new IMU drivers and filters are added to the library.
SyntroPiNav (an app for the Raspberry Pi) and SyntroNavView can be used as a convenient system to experiment with IMU chips, drivers and filters. SyntroPiNav runs on the Pi and transmits IMU data along with filter outputs over a LAN to SyntroNavView running on an Ubuntu PC. SyntroNavView also displays the data and provides a 3D graphics view of the calculated pose.
Since all IMU data is sent to SyntroNavView, SyntroNavView can run its own local filter. This makes it a very convenient testbed for new filter development as the speed of the desktop can be used to accelerate implementation and testing. When ready, the updated RTIMULib can be compiled into SyntroPiNav and should work exactly the same as on the desktop.
SyntroPiNav is available as part of the richards-tech SyntroPiApps repo (https://github.com/richards-tech/SyntroPiApps) while SyntroNavView is available as part of the richards-tech SyntroApps repo (https://github.com/richards-tech/SyntroApps).