void ath9k_hw_analog_shift_rmw(struct ath_hw *ah, u32 reg, u32 mask,
u32 shift, u32 val)
{
REG_RMW(ah, reg, ((val << shift) & mask), mask);
if (ah->config.analog_shiftreg)
udelay(100);
}
int ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
{
struct ath9k_nfcal_hist *h = NULL;
unsigned i, j;
u8 chainmask = (ah->rxchainmask << 3) | ah->rxchainmask;
struct ath_common *common = ath9k_hw_common(ah);
s16 default_nf = ath9k_hw_get_default_nf(ah, chan);
if (ah->caldata)
h = ah->caldata->nfCalHist;
ENABLE_REG_RMW_BUFFER(ah);
for (i = 0; i < NUM_NF_READINGS; i++) {
if (chainmask & (1 << i)) {
s16 nfval;
if ((i >= AR5416_MAX_CHAINS) && !IS_CHAN_HT40(chan))
continue;
if (h)
nfval = h[i].privNF;
else
nfval = default_nf;
REG_RMW(ah, ah->nf_regs[i],
(((u32) nfval << 1) & 0x1ff), 0x1ff);
}
}
/*
* Load software filtered NF value into baseband internal minCCApwr
* variable.
*/
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_ENABLE_NF);
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
REG_RMW_BUFFER_FLUSH(ah);
/*
* Wait for load to complete, should be fast, a few 10s of us.
* The max delay was changed from an original 250us to 10000us
* since 250us often results in NF load timeout and causes deaf
* condition during stress testing 12/12/2009
*/
for (j = 0; j < 10000; j++) {
if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
AR_PHY_AGC_CONTROL_NF) == 0)
break;
udelay(10);
}
/*
* We timed out waiting for the noisefloor to load, probably due to an
* in-progress rx. Simply return here and allow the load plenty of time
* to complete before the next calibration interval. We need to avoid
* trying to load -50 (which happens below) while the previous load is
* still in progress as this can cause rx deafness. Instead by returning
* here, the baseband nf cal will just be capped by our present
* noisefloor until the next calibration timer.
*/
if (j == 10000) {
ath_dbg(common, ANY,
"Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x%x\n",
REG_READ(ah, AR_PHY_AGC_CONTROL));
return -ETIMEDOUT;
}
/*
* Restore maxCCAPower register parameter again so that we're not capped
* by the median we just loaded. This will be initial (and max) value
* of next noise floor calibration the baseband does.
*/
ENABLE_REG_RMW_BUFFER(ah);
for (i = 0; i < NUM_NF_READINGS; i++) {
if (chainmask & (1 << i)) {
if ((i >= AR5416_MAX_CHAINS) && !IS_CHAN_HT40(chan))
continue;
REG_RMW(ah, ah->nf_regs[i],
(((u32) (-50) << 1) & 0x1ff), 0x1ff);
}
}
REG_RMW_BUFFER_FLUSH(ah);
return 0;
}