示例#1
0
/**
  * @brief Receive data in blocking mode. Must be invoked when RXBR has been set. 
  * @param hcec: CEC handle
  * @param pData: pointer to received data buffer.
  * @param Timeout: Timeout duration.
  *       Note that the received data size is not known beforehand, the latter is known
  *       when the reception is complete and is stored in hcec->RxXferSize.  
  *       hcec->RxXferSize is the sum of opcodes + operands (0 to 14 operands max).
  *       If only a header is received, hcec->RxXferSize = 0    
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CEC_Receive(CEC_HandleTypeDef *hcec, uint8_t *pData, uint32_t Timeout)
{ 
  uint32_t temp;
  uint32_t tickstart = 0;   

  if (hcec->State == HAL_CEC_STATE_READY)
  { 
    hcec->ErrorCode = HAL_CEC_ERROR_NONE;
    if (pData == NULL ) 
    {
      hcec->State = HAL_CEC_STATE_ERROR;
      return  HAL_ERROR;                                    
    }
    
    hcec->RxXferSize = 0;
    /* Process Locked */
    __HAL_LOCK(hcec);
    
    
    /* Rx loop until CEC_ISR_RXEND  is set */
    while (HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_FLAG_RXEND))
    {
      tickstart = HAL_GetTick();
      /* Wait for next byte to be received */
      while (HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_FLAG_RXBR))
      {
    	  if(Timeout != HAL_MAX_DELAY)
        {
          if((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout))
          {
            hcec->State = HAL_CEC_STATE_TIMEOUT;
            __HAL_UNLOCK(hcec);
            return HAL_TIMEOUT;
          }
        }
        /* any error so far ? 
         * has Rx Missing Acknowledge occurred ?
         * has Rx Long Bit Period error occurred ?
         * has Rx Short Bit Period error occurred ? 
         * has Rx Bit Rising error occurred ?             
         * has Rx Overrun error occurred ? */
        temp = (uint32_t) (hcec->Instance->ISR);
        if ((temp & (CEC_FLAG_RXACKE|CEC_FLAG_LBPE|CEC_FLAG_SBPE|CEC_FLAG_BRE|CEC_FLAG_RXOVR)) != 0)
        {
          /* copy ISR for error handling purposes */
          hcec->ErrorCode = temp;
          /* clear all error flags by default */
          __HAL_CEC_CLEAR_FLAG(hcec,(CEC_FLAG_RXACKE|CEC_FLAG_LBPE|CEC_FLAG_SBPE|CEC_FLAG_BRE|CEC_FLAG_RXOVR));
          hcec->State = HAL_CEC_STATE_ERROR;
          __HAL_UNLOCK(hcec);
          return  HAL_ERROR;                                    
        }
      } /* while (HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_ISR_RXBR)) */
  

      /* read received data */
      *pData++ = hcec->Instance->RXDR;
      temp = (uint32_t) (hcec->Instance->ISR);
      /* end of message ? */
      if ((temp &  CEC_ISR_RXEND) != 0)      
      {
         assert_param(IS_CEC_MSGSIZE(hcec->RxXferSize));
         __HAL_CEC_CLEAR_FLAG(hcec,CEC_FLAG_RXEND);
          hcec->State = HAL_CEC_STATE_READY;  
         __HAL_UNLOCK(hcec);  
         return HAL_OK; 
      }
      
      /* clear Rx-Byte Received flag */
      __HAL_CEC_CLEAR_FLAG(hcec,CEC_FLAG_RXBR); 
      /* increment payload byte counter */
       hcec->RxXferSize++;
    } /* while (HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_ISR_RXEND)) */ 
    
    /* if the instructions below are executed, it means RXEND was set when RXBR was 
     * set for the first time:
     * the code within the "while (HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_ISR_RXEND))"
     * loop has not been executed and this means a single byte has been sent */
    *pData++ = hcec->Instance->RXDR;
     /* only one header is received: RxXferSize is set to 0 (no operand, no opcode) */ 
     hcec->RxXferSize = 0;
     __HAL_CEC_CLEAR_FLAG(hcec, CEC_FLAG_RXEND);
                             
    hcec->State = HAL_CEC_STATE_READY;  
    __HAL_UNLOCK(hcec);  
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;   
  }
}
示例#2
0
/**
  * @brief  Open and configure an endpoint
  * @param  hpcd: PCD handle
  * @param  ep_addr: endpoint address
  * @param  ep_mps: endpoint max packert size
  * @param  ep_type: endpoint type   
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_PCD_EP_Open(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint16_t ep_mps, uint8_t ep_type)
{
  HAL_StatusTypeDef  ret = HAL_OK;
  PCD_EPTypeDef *ep;
  
  if ((ep_addr & 0x80) == 0x80)
  {
    ep = &hpcd->IN_ep[ep_addr & 0x7F];
  }
  else
  {
    ep = &hpcd->OUT_ep[ep_addr & 0x7F];
  }
  ep->num   = ep_addr & 0x7F;
  
  ep->is_in = (0x80 & ep_addr) != 0;
  ep->maxpacket = ep_mps;
  ep->type = ep_type;
  
  __HAL_LOCK(hpcd); 

/* initialize Endpoint */
  switch (ep->type)
  {
  case PCD_EP_TYPE_CTRL:
    PCD_SET_EPTYPE(hpcd->Instance, ep->num, USB_EP_CONTROL);
    break;
  case PCD_EP_TYPE_BULK:
    PCD_SET_EPTYPE(hpcd->Instance, ep->num, USB_EP_BULK);
    break;
  case PCD_EP_TYPE_INTR:
    PCD_SET_EPTYPE(hpcd->Instance, ep->num, USB_EP_INTERRUPT);
    break;
  case PCD_EP_TYPE_ISOC:
    PCD_SET_EPTYPE(hpcd->Instance, ep->num, USB_EP_ISOCHRONOUS);
    break;
  } 
  
  PCD_SET_EP_ADDRESS(hpcd->Instance, ep->num, ep->num);
  
  if (ep->doublebuffer == 0) 
  {
    if (ep->is_in)
    {
      /*Set the endpoint Transmit buffer address */
      PCD_SET_EP_TX_ADDRESS(hpcd->Instance, ep->num, ep->pmaadress);
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      /* Configure NAK status for the Endpoint*/
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_NAK); 
    }
    else
    {
      /*Set the endpoint Receive buffer address */
      PCD_SET_EP_RX_ADDRESS(hpcd->Instance, ep->num, ep->pmaadress);
      /*Set the endpoint Receive buffer counter*/
      PCD_SET_EP_RX_CNT(hpcd->Instance, ep->num, ep->maxpacket);
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      /* Configure VALID status for the Endpoint*/
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_VALID);
    }
  }
  /*Double Buffer*/
  else
  {
    /*Set the endpoint as double buffered*/
    PCD_SET_EP_DBUF(hpcd->Instance, ep->num);
    /*Set buffer address for double buffered mode*/
    PCD_SET_EP_DBUF_ADDR(hpcd->Instance, ep->num,ep->pmaaddr0, ep->pmaaddr1);
    
    if (ep->is_in==0)
    {
      /* Clear the data toggle bits for the endpoint IN/OUT*/
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      
      /* Reset value of the data toggle bits for the endpoint out*/
      PCD_TX_DTOG(hpcd->Instance, ep->num);
      
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_VALID);
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_DIS);
    }
    else
    {
      /* Clear the data toggle bits for the endpoint IN/OUT*/
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      PCD_RX_DTOG(hpcd->Instance, ep->num);
      /* Configure DISABLE status for the Endpoint*/
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_DIS);
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_DIS);
    }
  } 
  
  __HAL_UNLOCK(hpcd);   
  return ret;
}
示例#3
0
/**
  * @brief  Initiates and transmits a CAN frame message.
  * @param  hcan: pointer to a CAN_HandleTypeDef structure that contains
  *         the configuration information for the specified CAN.  
  * @param  Timeout: Specify Timeout value   
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef* hcan, uint32_t Timeout)
{
  uint32_t  transmitmailbox = 5;
  uint32_t tickstart = 0;

  /* Check the parameters */
  assert_param(IS_CAN_IDTYPE(hcan->pTxMsg->IDE));
  assert_param(IS_CAN_RTR(hcan->pTxMsg->RTR));
  assert_param(IS_CAN_DLC(hcan->pTxMsg->DLC));
  
  /* Process locked */
  __HAL_LOCK(hcan);
  
  if(hcan->State == HAL_CAN_STATE_BUSY_RX) 
  {
    /* Change CAN state */
    hcan->State = HAL_CAN_STATE_BUSY_TX_RX;
  }
  else
  {
    /* Change CAN state */
    hcan->State = HAL_CAN_STATE_BUSY_TX;
  }
  
  /* Select one empty transmit mailbox */
  if ((hcan->Instance->TSR&CAN_TSR_TME0) == CAN_TSR_TME0)
  {
    transmitmailbox = 0;
  }
  else if ((hcan->Instance->TSR&CAN_TSR_TME1) == CAN_TSR_TME1)
  {
    transmitmailbox = 1;
  }
  else if ((hcan->Instance->TSR&CAN_TSR_TME2) == CAN_TSR_TME2)
  {
    transmitmailbox = 2;
  }
  else
  {
    transmitmailbox = CAN_TXSTATUS_NOMAILBOX;
  }

  if (transmitmailbox != CAN_TXSTATUS_NOMAILBOX)
  {
    /* Set up the Id */
    hcan->Instance->sTxMailBox[transmitmailbox].TIR &= CAN_TI0R_TXRQ;
    if (hcan->pTxMsg->IDE == CAN_ID_STD)
    {
      assert_param(IS_CAN_STDID(hcan->pTxMsg->StdId));  
      hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->StdId << 21) | \
                                                  hcan->pTxMsg->RTR);
    }
    else
    {
      assert_param(IS_CAN_EXTID(hcan->pTxMsg->ExtId));
      hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->ExtId << 3) | \
                                                  hcan->pTxMsg->IDE | \
                                                  hcan->pTxMsg->RTR);
    }
    
    /* Set up the DLC */
    hcan->pTxMsg->DLC &= (uint8_t)0x0000000F;
    hcan->Instance->sTxMailBox[transmitmailbox].TDTR &= (uint32_t)0xFFFFFFF0;
    hcan->Instance->sTxMailBox[transmitmailbox].TDTR |= hcan->pTxMsg->DLC;

    /* Set up the data field */
    hcan->Instance->sTxMailBox[transmitmailbox].TDLR = (((uint32_t)hcan->pTxMsg->Data[3] << 24) | 
                                             ((uint32_t)hcan->pTxMsg->Data[2] << 16) |
                                             ((uint32_t)hcan->pTxMsg->Data[1] << 8) | 
                                             ((uint32_t)hcan->pTxMsg->Data[0]));
    hcan->Instance->sTxMailBox[transmitmailbox].TDHR = (((uint32_t)hcan->pTxMsg->Data[7] << 24) | 
                                             ((uint32_t)hcan->pTxMsg->Data[6] << 16) |
                                             ((uint32_t)hcan->pTxMsg->Data[5] << 8) |
                                             ((uint32_t)hcan->pTxMsg->Data[4]));
    /* Request transmission */
    hcan->Instance->sTxMailBox[transmitmailbox].TIR |= CAN_TI0R_TXRQ;
  
  /* Get tick */ 
  tickstart = HAL_GetTick();
  
    /* Check End of transmission flag */
    while(!(__HAL_CAN_TRANSMIT_STATUS(hcan, transmitmailbox)))
    {
      /* Check for the Timeout */
      if(Timeout != HAL_MAX_DELAY)
      {
       if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
       {
         hcan->State = HAL_CAN_STATE_TIMEOUT;
         /* Process unlocked */
         __HAL_UNLOCK(hcan);
         return HAL_TIMEOUT;
        }
      }
    }
    if(hcan->State == HAL_CAN_STATE_BUSY_TX_RX) 
    {
      /* Change CAN state */
      hcan->State = HAL_CAN_STATE_BUSY_RX;
      
      /* Process unlocked */
      __HAL_UNLOCK(hcan);
    }
    else
    {
      /* Change CAN state */
      hcan->State = HAL_CAN_STATE_READY;
      
      /* Process unlocked */
      __HAL_UNLOCK(hcan);
    }
    
    /* Return function status */
    return HAL_OK;
  }
  else
  {
    /* Change CAN state */
    hcan->State = HAL_CAN_STATE_ERROR; 
    
    /* Return function status */
    return HAL_ERROR;
  }
}
示例#4
0
/**
  * @brief  Configures for the selected ADC injected channel its corresponding
  *         rank in the sequencer and its sample time.
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  * @param  sConfigInjected: ADC configuration structure for injected channel. 
  * @retval None
  */
HAL_StatusTypeDef HAL_ADCEx_InjectedConfigChannel(ADC_HandleTypeDef* hadc, ADC_InjectionConfTypeDef* sConfigInjected)
{
  
#ifdef USE_FULL_ASSERT  
  uint32_t tmp = 0;
#endif /* USE_FULL_ASSERT  */
  
  /* Check the parameters */
  assert_param(IS_ADC_CHANNEL(sConfigInjected->InjectedChannel));
  assert_param(IS_ADC_INJECTED_RANK(sConfigInjected->InjectedRank));
  assert_param(IS_ADC_SAMPLE_TIME(sConfigInjected->InjectedSamplingTime));
  assert_param(IS_ADC_EXT_INJEC_TRIG(sConfigInjected->ExternalTrigInjecConv));
  assert_param(IS_ADC_INJECTED_LENGTH(sConfigInjected->InjectedNbrOfConversion));
  assert_param(IS_FUNCTIONAL_STATE(sConfigInjected->AutoInjectedConv));
  assert_param(IS_FUNCTIONAL_STATE(sConfigInjected->InjectedDiscontinuousConvMode));

#ifdef USE_FULL_ASSERT
  tmp = ADC_GET_RESOLUTION(hadc);
  assert_param(IS_ADC_RANGE(tmp, sConfigInjected->InjectedOffset));
#endif /* USE_FULL_ASSERT  */

  if(sConfigInjected->ExternalTrigInjecConvEdge != ADC_INJECTED_SOFTWARE_START)
  {
    assert_param(IS_ADC_EXT_INJEC_TRIG_EDGE(sConfigInjected->ExternalTrigInjecConvEdge));
  }

  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* if ADC_Channel_10 ... ADC_Channel_18 is selected */
  if (sConfigInjected->InjectedChannel > ADC_CHANNEL_9)
  {
    /* Clear the old sample time */
    hadc->Instance->SMPR1 &= ~ADC_SMPR1(ADC_SMPR1_SMP10, sConfigInjected->InjectedChannel);
    
    /* Set the new sample time */
    hadc->Instance->SMPR1 |= ADC_SMPR1(sConfigInjected->InjectedSamplingTime, sConfigInjected->InjectedChannel);
  }
  else /* ADC_Channel include in ADC_Channel_[0..9] */
  {
    /* Clear the old sample time */
    hadc->Instance->SMPR2 &= ~ADC_SMPR2(ADC_SMPR2_SMP0, sConfigInjected->InjectedChannel);
    
    /* Set the new sample time */
    hadc->Instance->SMPR2 |= ADC_SMPR2(sConfigInjected->InjectedSamplingTime, sConfigInjected->InjectedChannel);
  }
  
  /*---------------------------- ADCx JSQR Configuration -----------------*/
  hadc->Instance->JSQR &= ~(ADC_JSQR_JL);
  hadc->Instance->JSQR |=  ADC_SQR1(sConfigInjected->InjectedNbrOfConversion);
  
  /* Rank configuration */
  
  /* Clear the old SQx bits for the selected rank */
  hadc->Instance->JSQR &= ~ADC_JSQR(ADC_JSQR_JSQ1, sConfigInjected->InjectedRank,sConfigInjected->InjectedNbrOfConversion);
   
  /* Set the SQx bits for the selected rank */
  hadc->Instance->JSQR |= ADC_JSQR(sConfigInjected->InjectedChannel, sConfigInjected->InjectedRank,sConfigInjected->InjectedNbrOfConversion);

  /* Enable external trigger if trigger selection is different of software  */
  /* start.                                                                 */
  /* Note: This configuration keeps the hardware feature of parameter       */
  /*       ExternalTrigConvEdge "trigger edge none" equivalent to           */
  /*       software start.                                                  */ 
  if(sConfigInjected->ExternalTrigInjecConv != ADC_INJECTED_SOFTWARE_START)
  {  
    /* Select external trigger to start conversion */
    hadc->Instance->CR2 &= ~(ADC_CR2_JEXTSEL);
    hadc->Instance->CR2 |=  sConfigInjected->ExternalTrigInjecConv;
    
    /* Select external trigger polarity */
    hadc->Instance->CR2 &= ~(ADC_CR2_JEXTEN);
    hadc->Instance->CR2 |= sConfigInjected->ExternalTrigInjecConvEdge;
  }
  else
  {
    /* Reset the external trigger */
    hadc->Instance->CR2 &= ~(ADC_CR2_JEXTSEL);
    hadc->Instance->CR2 &= ~(ADC_CR2_JEXTEN);  
  }
  
  if (sConfigInjected->AutoInjectedConv != DISABLE)
  {
    /* Enable the selected ADC automatic injected group conversion */
    hadc->Instance->CR1 |= ADC_CR1_JAUTO;
  }
  else
  {
    /* Disable the selected ADC automatic injected group conversion */
    hadc->Instance->CR1 &= ~(ADC_CR1_JAUTO);
  }
  
  if (sConfigInjected->InjectedDiscontinuousConvMode != DISABLE)
  {
    /* Enable the selected ADC injected discontinuous mode */
    hadc->Instance->CR1 |= ADC_CR1_JDISCEN;
  }
  else
  {
    /* Disable the selected ADC injected discontinuous mode */
    hadc->Instance->CR1 &= ~(ADC_CR1_JDISCEN);
  }
  
  switch(sConfigInjected->InjectedRank)
  {
    case 1:
      /* Set injected channel 1 offset */
      hadc->Instance->JOFR1 &= ~(ADC_JOFR1_JOFFSET1);
      hadc->Instance->JOFR1 |= sConfigInjected->InjectedOffset;
      break;
    case 2:
      /* Set injected channel 2 offset */
      hadc->Instance->JOFR2 &= ~(ADC_JOFR2_JOFFSET2);
      hadc->Instance->JOFR2 |= sConfigInjected->InjectedOffset;
      break;
    case 3:
      /* Set injected channel 3 offset */
      hadc->Instance->JOFR3 &= ~(ADC_JOFR3_JOFFSET3);
      hadc->Instance->JOFR3 |= sConfigInjected->InjectedOffset;
      break;
    default:
      /* Set injected channel 4 offset */
      hadc->Instance->JOFR4 &= ~(ADC_JOFR4_JOFFSET4);
      hadc->Instance->JOFR4 |= sConfigInjected->InjectedOffset;
      break;
  }
  
  /* if ADC1 Channel_18 is selected enable VBAT Channel */
  if ((hadc->Instance == ADC1) && (sConfigInjected->InjectedChannel == ADC_CHANNEL_VBAT))
  {
    /* Enable the VBAT channel*/
    ADC->CCR |= ADC_CCR_VBATE;
  }
  
  /* if ADC1 Channel_16 or Channel_17 is selected enable TSVREFE Channel(Temperature sensor and VREFINT) */
  if ((hadc->Instance == ADC1) && ((sConfigInjected->InjectedChannel == ADC_CHANNEL_TEMPSENSOR) || (sConfigInjected->InjectedChannel == ADC_CHANNEL_VREFINT)))
  {
    /* Enable the TSVREFE channel*/
    ADC->CCR |= ADC_CCR_TSVREFE;
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return HAL_OK;
}
示例#5
0
/**
  * @brief  Enables DAC and starts conversion of channel.
  * @param  hdac: pointer to a DAC_HandleTypeDef structure that contains
  *         the configuration information for the specified DAC.
  * @param  Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_CHANNEL_1: DAC Channel1 selected
  *            @arg DAC_CHANNEL_2: DAC Channel2 selected
  * @param  pData: The destination peripheral Buffer address.
  * @param  Length: The length of data to be transferred from memory to DAC peripheral
  * @param  Alignment: Specifies the data alignment for DAC channel.
  *          This parameter can be one of the following values:
  *            @arg DAC_ALIGN_8B_R: 8bit right data alignment selected
  *            @arg DAC_ALIGN_12B_L: 12bit left data alignment selected
  *            @arg DAC_ALIGN_12B_R: 12bit right data alignment selected
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DAC_Start_DMA(DAC_HandleTypeDef* hdac, uint32_t Channel, uint32_t* pData, uint32_t Length, uint32_t Alignment)
{
  uint32_t tmpreg = 0;
    
  /* Check the parameters */
  assert_param(IS_DAC_CHANNEL(Channel));
  assert_param(IS_DAC_ALIGN(Alignment));
  
  /* Process locked */
  __HAL_LOCK(hdac);
  
  /* Change DAC state */
  hdac->State = HAL_DAC_STATE_BUSY;
  
  if(Channel == DAC_CHANNEL_1)
  {
    /* Set the DMA transfer complete callback for channel1 */
    hdac->DMA_Handle1->XferCpltCallback = DAC_DMAConvCpltCh1;
    
    /* Set the DMA half transfer complete callback for channel1 */
    hdac->DMA_Handle1->XferHalfCpltCallback = DAC_DMAHalfConvCpltCh1;
       
    /* Set the DMA error callback for channel1 */
    hdac->DMA_Handle1->XferErrorCallback = DAC_DMAErrorCh1;
    
    /* Enable the selected DAC channel1 DMA request */
    SET_BIT(hdac->Instance->CR, DAC_CR_DMAEN1);
    
    /* Case of use of channel 1 */
    switch(Alignment)
    {
      case DAC_ALIGN_12B_R:
        /* Get DHR12R1 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR12R1;
        break;
      case DAC_ALIGN_12B_L:
        /* Get DHR12L1 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR12L1;
        break;
      case DAC_ALIGN_8B_R:
        /* Get DHR8R1 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR8R1;
        break;
      default:
        break;
    }
  }
  else
  {
    /* Set the DMA transfer complete callback for channel2 */
    hdac->DMA_Handle2->XferCpltCallback = DAC_DMAConvCpltCh2;
    
    /* Set the DMA half transfer complete callback for channel2 */
    hdac->DMA_Handle2->XferHalfCpltCallback = DAC_DMAHalfConvCpltCh2;
       
    /* Set the DMA error callback for channel2 */
    hdac->DMA_Handle2->XferErrorCallback = DAC_DMAErrorCh2;
    
    /* Enable the selected DAC channel2 DMA request */
    SET_BIT(hdac->Instance->CR, DAC_CR_DMAEN2);
    
    /* Case of use of channel 2 */
    switch(Alignment)
    {
      case DAC_ALIGN_12B_R:
        /* Get DHR12R2 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR12R2;
        break;
      case DAC_ALIGN_12B_L:
        /* Get DHR12L2 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR12L2;
        break;
      case DAC_ALIGN_8B_R:
        /* Get DHR8R2 address */
        tmpreg = (uint32_t)&hdac->Instance->DHR8R2;
        break;
      default:
        break;
    }
  }
  
  /* Enable the DMA channel */
  if(Channel == DAC_CHANNEL_1)
  {
    /* Enable the DAC DMA underrun interrupt */
    __HAL_DAC_ENABLE_IT(hdac, DAC_IT_DMAUDR1);
    
    /* Enable the DMA channel */
    HAL_DMA_Start_IT(hdac->DMA_Handle1, (uint32_t)pData, tmpreg, Length);
  } 
  else
  {
    /* Enable the DAC DMA underrun interrupt */
    __HAL_DAC_ENABLE_IT(hdac, DAC_IT_DMAUDR2);
    
    /* Enable the DMA channel */
    HAL_DMA_Start_IT(hdac->DMA_Handle2, (uint32_t)pData, tmpreg, Length);
  }
  
  /* Process Unlocked */
  __HAL_UNLOCK(hdac);

  /* Enable the Peripheral */
  __HAL_DAC_ENABLE(hdac, Channel);
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief  Enables the interrupt and starts ADC conversion of injected channels.
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  *
  * @retval HAL status.
  */
HAL_StatusTypeDef HAL_ADCEx_InjectedStart_IT(ADC_HandleTypeDef* hadc)
{
  __IO uint32_t counter = 0;
  uint32_t tmp1 = 0, tmp2 =0;
  
  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* Check if a regular conversion is ongoing */
  if(hadc->State == HAL_ADC_STATE_BUSY_REG)
  {
    /* Change ADC state */
    hadc->State = HAL_ADC_STATE_BUSY_INJ_REG;  
  }
  else
  {
    /* Change ADC state */
    hadc->State = HAL_ADC_STATE_BUSY_INJ;
  }
  
  /* Set ADC error code to none */
  hadc->ErrorCode = HAL_ADC_ERROR_NONE;
  
  /* Check if ADC peripheral is disabled in order to enable it and wait during 
     Tstab time the ADC's stabilization */
  if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
  {  
    /* Enable the Peripheral */
    __HAL_ADC_ENABLE(hadc);
    
    /* Delay for temperature sensor stabilization time */
    /* Compute number of CPU cycles to wait for */
    counter = (ADC_STAB_DELAY_US * (SystemCoreClock / 1000000));
    while(counter != 0)
    {
      counter--;
    }
  }
  
  /* Enable the ADC end of conversion interrupt for injected group */
  __HAL_ADC_ENABLE_IT(hadc, ADC_IT_JEOC);
  
  /* Enable the ADC overrun interrupt */
  __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
  
  /* Check if Multimode enabled */
  if(HAL_IS_BIT_CLR(ADC->CCR, ADC_CCR_MULTI))
  {
    tmp1 = HAL_IS_BIT_CLR(hadc->Instance->CR2, ADC_CR2_JEXTEN);
    tmp2 = HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO);
    if(tmp1 && tmp2)
    {
      /* Enable the selected ADC software conversion for injected group */
      hadc->Instance->CR2 |= ADC_CR2_JSWSTART;
    }
  }
  else
  {
    tmp1 = HAL_IS_BIT_CLR(hadc->Instance->CR2, ADC_CR2_JEXTEN);
    tmp2 = HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO);
    if((hadc->Instance == ADC1) && tmp1 && tmp2)  
    {
      /* Enable the selected ADC software conversion for injected group */
      hadc->Instance->CR2 |= ADC_CR2_JSWSTART;
    }
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return HAL_OK;
}
示例#7
0
/**
  * @brief  Enables the interrupt and starts ADC conversion of injected channels.
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  *
  * @retval HAL status.
  */
HAL_StatusTypeDef HAL_ADCEx_InjectedStart_IT(ADC_HandleTypeDef* hadc)
{
  __IO uint32_t counter = 0;
  uint32_t tmp1 = 0, tmp2 = 0;
  
  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* Enable the ADC peripheral */
  
  /* Check if ADC peripheral is disabled in order to enable it and wait during 
     Tstab time the ADC's stabilization */
  if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
  {  
    /* Enable the Peripheral */
    __HAL_ADC_ENABLE(hadc);
    
    /* Delay for ADC stabilization time */
    /* Compute number of CPU cycles to wait for */
    counter = (ADC_STAB_DELAY_US * (SystemCoreClock / 1000000));
    while(counter != 0)
    {
      counter--;
    }
  }
  
  /* Start conversion if ADC is effectively enabled */
  if(HAL_IS_BIT_SET(hadc->Instance->CR2, ADC_CR2_ADON))
  {
    /* Set ADC state                                                          */
    /* - Clear state bitfield related to injected group conversion results    */
    /* - Set state bitfield related to injected operation                     */
    ADC_STATE_CLR_SET(hadc->State,
                      HAL_ADC_STATE_READY | HAL_ADC_STATE_INJ_EOC,
                      HAL_ADC_STATE_INJ_BUSY);
    
    /* Check if a regular conversion is ongoing */
    /* Note: On this device, there is no ADC error code fields related to     */
    /*       conversions on group injected only. In case of conversion on     */
    /*       going on group regular, no error code is reset.                  */
    if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_REG_BUSY))
    {
      /* Reset ADC all error code fields */
      ADC_CLEAR_ERRORCODE(hadc);
    }
    
    /* Process unlocked */
    /* Unlock before starting ADC conversions: in case of potential           */
    /* interruption, to let the process to ADC IRQ Handler.                   */
    __HAL_UNLOCK(hadc);
    
    /* Clear injected group conversion flag */
    /* (To ensure of no unknown state from potential previous ADC operations) */
    __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_JEOC);
    
    /* Enable end of conversion interrupt for injected channels */
    __HAL_ADC_ENABLE_IT(hadc, (ADC_IT_JEOC | ADC_IT_OVR));
    
    /* Check if Multimode enabled */
    if(HAL_IS_BIT_CLR(ADC->CCR, ADC_CCR_MULTI))
    {
      tmp1 = HAL_IS_BIT_CLR(hadc->Instance->CR2, ADC_CR2_JEXTEN);
      tmp2 = HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO);
      if(tmp1 && tmp2)
      {
        /* Enable the selected ADC software conversion for injected group */
        hadc->Instance->CR2 |= ADC_CR2_JSWSTART;
      }
    }
    else
    {
      tmp1 = HAL_IS_BIT_CLR(hadc->Instance->CR2, ADC_CR2_JEXTEN);
      tmp2 = HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO);
      if((hadc->Instance == ADC1) && tmp1 && tmp2)  
      {
        /* Enable the selected ADC software conversion for injected group */
        hadc->Instance->CR2 |= ADC_CR2_JSWSTART;
      }
    }
  }
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief Full-Duplex Transmit/Receive data in non-blocking mode using Interrupt 
  * @param  hi2s: pointer to a I2S_HandleTypeDef structure that contains
  *         the configuration information for I2S module
  * @param pTxData: a 16-bit pointer to the Transmit data buffer.
  * @param pRxData: a 16-bit pointer to the Receive data buffer.
  * @param Size: number of data sample to be sent:
  * @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
  *       configuration phase, the Size parameter means the number of 16-bit data length 
  *       in the transaction and when a 24-bit data frame or a 32-bit data frame is selected 
  *       the Size parameter means the number of 16-bit data length. 
  * @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization 
  *       between Master and Slave(example: audio streaming).
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_I2SEx_TransmitReceive_IT(I2S_HandleTypeDef *hi2s, uint16_t *pTxData, uint16_t *pRxData, uint16_t Size)
{
  uint32_t tmp1 = 0, tmp2 = 0;
  
  if(hi2s->State == HAL_I2S_STATE_READY)
  {
    if((pTxData == NULL ) || (pRxData == NULL ) || (Size == 0)) 
    {
      return  HAL_ERROR;
    }

    hi2s->pTxBuffPtr = pTxData;
    hi2s->pRxBuffPtr = pRxData;

    tmp1 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN);
    tmp2 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN);
    /* Check the Data format: When a 16-bit data frame or a 16-bit data frame extended 
       is selected during the I2S configuration phase, the Size parameter means the number
       of 16-bit data length in the transaction and when a 24-bit data frame or a 32-bit data 
       frame is selected the Size parameter means the number of 16-bit data length. */
    if((tmp1 == I2S_DATAFORMAT_24B)||\
       (tmp2 == I2S_DATAFORMAT_32B))
    {
      hi2s->TxXferSize = Size*2;
      hi2s->TxXferCount = Size*2;
      hi2s->RxXferSize = Size*2;
      hi2s->RxXferCount = Size*2;
    }  
    else
    {
      hi2s->TxXferSize = Size;
      hi2s->TxXferCount = Size;
      hi2s->RxXferSize = Size;
      hi2s->RxXferCount = Size;
    }
    
    /* Process Locked */
    __HAL_LOCK(hi2s);
    
    hi2s->State = HAL_I2S_STATE_BUSY_TX_RX;
    hi2s->ErrorCode = HAL_I2S_ERROR_NONE;

    tmp1 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    tmp2 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    /* Check if the I2S_MODE_MASTER_TX or I2S_MODE_SLAVE_TX Mode is selected */
    if((tmp1 == I2S_MODE_MASTER_TX) || (tmp2 == I2S_MODE_SLAVE_TX))
    { 
      /* Enable I2Sext RXNE and ERR interrupts */
      I2SxEXT(hi2s->Instance)->CR2 |= (I2S_IT_RXNE | I2S_IT_ERR);

      /* Enable I2Sx TXE and ERR interrupts */
      __HAL_I2S_ENABLE_IT(hi2s, (I2S_IT_TXE | I2S_IT_ERR));

      /* Check if the I2S is already enabled */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Enable I2Sext(receiver) before enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;

        /* Enable I2Sx peripheral */
        __HAL_I2S_ENABLE(hi2s);
      }
    }
    /* The I2S_MODE_MASTER_RX or I2S_MODE_SLAVE_RX Mode is selected */
    else
    {
      /* Enable I2Sext TXE and ERR interrupts */
      I2SxEXT(hi2s->Instance)->CR2 |= (I2S_IT_TXE |I2S_IT_ERR);

      /* Enable I2Sext RXNE and ERR interrupts */
      __HAL_I2S_ENABLE_IT(hi2s, (I2S_IT_RXNE | I2S_IT_ERR));

      /* Check if the I2S is already enabled */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Check if the I2S_MODE_MASTER_RX is selected */
        if((hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG) == I2S_MODE_MASTER_RX) 
        {
          /* Prepare the First Data before enabling the I2S */
          if(hi2s->TxXferCount != 0)
          {
            /* Transmit First data */
            I2SxEXT(hi2s->Instance)->DR = (*hi2s->pTxBuffPtr++);
            hi2s->TxXferCount--;	

            if(hi2s->TxXferCount == 0)
            {
              /* Disable I2Sext TXE interrupt */
              I2SxEXT(hi2s->Instance)->CR2 &= ~I2S_IT_TXE;
            }
          }
        }
        /* Enable I2S peripheral */
        __HAL_I2S_ENABLE(hi2s);
        
        /* Enable I2Sext(transmitter) after enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;
      }
    }
    /* Process Unlocked */
    __HAL_UNLOCK(hi2s);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
/**
  * @brief Full-Duplex Transmit/Receive data in non-blocking mode using DMA  
  * @param  hi2s: pointer to a I2S_HandleTypeDef structure that contains
  *         the configuration information for I2S module
  * @param pTxData: a 16-bit pointer to the Transmit data buffer.
  * @param pRxData: a 16-bit pointer to the Receive data buffer.
  * @param Size: number of data sample to be sent:
  * @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
  *       configuration phase, the Size parameter means the number of 16-bit data length 
  *       in the transaction and when a 24-bit data frame or a 32-bit data frame is selected 
  *       the Size parameter means the number of 16-bit data length. 
  * @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization 
  *       between Master and Slave(example: audio streaming).
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_I2SEx_TransmitReceive_DMA(I2S_HandleTypeDef *hi2s, uint16_t *pTxData, uint16_t *pRxData, uint16_t Size)
{
  uint32_t *tmp;
  uint32_t tmp1 = 0, tmp2 = 0;
    
  if((pTxData == NULL ) || (pRxData == NULL ) || (Size == 0)) 
  {
    return  HAL_ERROR;
  }

  if(hi2s->State == HAL_I2S_STATE_READY)
  {
    hi2s->pTxBuffPtr = pTxData;
    hi2s->pRxBuffPtr = pRxData;

    tmp1 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN);
    tmp2 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN);
    /* Check the Data format: When a 16-bit data frame or a 16-bit data frame extended 
       is selected during the I2S configuration phase, the Size parameter means the number
       of 16-bit data length in the transaction and when a 24-bit data frame or a 32-bit data 
       frame is selected the Size parameter means the number of 16-bit data length. */
    if((tmp1 == I2S_DATAFORMAT_24B)||\
       (tmp2 == I2S_DATAFORMAT_32B))
    {
      hi2s->TxXferSize = Size*2;
      hi2s->TxXferCount = Size*2;
      hi2s->RxXferSize = Size*2;
      hi2s->RxXferCount = Size*2;
    }
    else
    {
      hi2s->TxXferSize = Size;
      hi2s->TxXferCount = Size;
      hi2s->RxXferSize = Size;
      hi2s->RxXferCount = Size;
    }

    /* Process Locked */
    __HAL_LOCK(hi2s);

    hi2s->State = HAL_I2S_STATE_BUSY_TX_RX;
    hi2s->ErrorCode = HAL_I2S_ERROR_NONE;

    /* Set the I2S Rx DMA Half transfert complete callback */
    hi2s->hdmarx->XferHalfCpltCallback = I2S_DMARxHalfCplt;

    /* Set the I2S Rx DMA transfert complete callback */
    hi2s->hdmarx->XferCpltCallback = I2S_DMARxCplt;

    /* Set the I2S Rx DMA error callback */
    hi2s->hdmarx->XferErrorCallback = I2S_DMAError;

    /* Set the I2S Tx DMA Half transfert complete callback */
    hi2s->hdmatx->XferHalfCpltCallback = I2S_DMATxHalfCplt;

    /* Set the I2S Tx DMA transfert complete callback */
    hi2s->hdmatx->XferCpltCallback = I2S_DMATxCplt;

    /* Set the I2S Tx DMA error callback */
    hi2s->hdmatx->XferErrorCallback = I2S_DMAError;

    tmp1 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    tmp2 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    /* Check if the I2S_MODE_MASTER_TX or I2S_MODE_SLAVE_TX Mode is selected */
    if((tmp1 == I2S_MODE_MASTER_TX) || (tmp2 == I2S_MODE_SLAVE_TX))
    {
      /* Enable the Rx DMA Stream */
      tmp = (uint32_t*)&pRxData;
      HAL_DMA_Start_IT(hi2s->hdmarx, (uint32_t)&I2SxEXT(hi2s->Instance)->DR, *(uint32_t*)tmp, hi2s->RxXferSize);

      /* Enable Rx DMA Request */  
      I2SxEXT(hi2s->Instance)->CR2 |= SPI_CR2_RXDMAEN;

      /* Enable the Tx DMA Stream */
      tmp = (uint32_t*)&pTxData;
      HAL_DMA_Start_IT(hi2s->hdmatx, *(uint32_t*)tmp, (uint32_t)&hi2s->Instance->DR, hi2s->TxXferSize);

      /* Enable Tx DMA Request */  
      hi2s->Instance->CR2 |= SPI_CR2_TXDMAEN;

      /* Check if the I2S is already enabled */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Enable I2Sext(receiver) before enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;

        /* Enable I2S peripheral after the I2Sext */
        __HAL_I2S_ENABLE(hi2s);
      }
    }
    else
    {
      /* Enable the Tx DMA Stream */
      tmp = (uint32_t*)&pTxData;
      HAL_DMA_Start_IT(hi2s->hdmatx, *(uint32_t*)tmp, (uint32_t)&I2SxEXT(hi2s->Instance)->DR, hi2s->TxXferSize);

      /* Enable Tx DMA Request */  
      I2SxEXT(hi2s->Instance)->CR2 |= SPI_CR2_TXDMAEN;

      /* Enable the Rx DMA Stream */
      tmp = (uint32_t*)&pRxData;
      HAL_DMA_Start_IT(hi2s->hdmarx, (uint32_t)&hi2s->Instance->DR, *(uint32_t*)tmp, hi2s->RxXferSize);

      /* Enable Rx DMA Request */  
      hi2s->Instance->CR2 |= SPI_CR2_RXDMAEN;

      /* Check if the I2S is already enabled */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Enable I2S peripheral before the I2Sext */
        __HAL_I2S_ENABLE(hi2s);

        /* Enable I2Sext(transmitter) after enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;
      }
      else
      {
        /* Check if Master Receiver mode is selected */
        if((hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG) == I2S_MODE_MASTER_RX)
        {
          /* Clear the Overrun Flag by a read operation on the SPI_DR register followed by a read
          access to the SPI_SR register. */ 
          __HAL_I2S_CLEAR_OVRFLAG(hi2s);
        }
      }
    }

    /* Process Unlocked */
    __HAL_UNLOCK(hi2s);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
示例#10
0
/**
  * @brief  Write sector to PCCARD memory
  * @param  hpccard: pointer to a PCCARD_HandleTypeDef structure that contains
  *                the configuration information for PCCARD module.
  * @param  pBuffer: pointer to source write buffer
  * @param  SectorAddress: Sector address to write
  * @param  pStatus: pointer to CF status
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_PCCARD_Write_Sector(PCCARD_HandleTypeDef *hpccard, uint16_t *pBuffer, uint16_t SectorAddress,  uint8_t *pStatus)
{
  uint32_t timeout = PCCARD_TIMEOUT_SECTOR, index = 0;
  uint8_t status = 0;

  /* Process Locked */
  __HAL_LOCK(hpccard);  
  
  /* Check the PCCARD controller state */
  if(hpccard->State == HAL_PCCARD_STATE_BUSY)
  {
     return HAL_BUSY;
  }
   
  /* Update the PCCARD controller state */
  hpccard->State = HAL_PCCARD_STATE_BUSY;
    
  /* Initialize CF status */
  *pStatus = PCCARD_READY;  
    
  /* Set the parameters to write a sector */
  *(__IO uint16_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR | ATA_CYLINDER_HIGH) = (uint16_t)0x00;
  *(__IO uint16_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR | ATA_SECTOR_COUNT)  = ((uint16_t)0x0100 ) | ((uint16_t)SectorAddress);
  *(__IO uint16_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR | ATA_STATUS_CMD)    = (uint16_t)0x30A0;
  
  do
  {
    /* Wait till the Status = PCCARD_STATUS_OK */
    status =  *(__IO uint8_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR | ATA_STATUS_CMD_ALTERNATE);
    timeout--;
  }while((status != PCCARD_STATUS_OK) && timeout);
  
  if(timeout == 0)
  {
    *pStatus = PCCARD_TIMEOUT_ERROR;
  }
  
  /* Write bytes */
  for(; index < PCCARD_SECTOR_SIZE; index++)
  {
    *(uint16_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR) = *(uint16_t *)pBuffer++;
  }

  do
  {
    /* Wait till the Status = PCCARD_STATUS_WRITE_OK */
    status =  *(__IO uint8_t *)(PCCARD_IO_SPACE_PRIMARY_ADDR | ATA_STATUS_CMD_ALTERNATE);
    timeout--;
  }while((status != PCCARD_STATUS_WRITE_OK) && timeout);

  if(timeout == 0)
  {
    *pStatus = PCCARD_TIMEOUT_ERROR;
  }  

  /* Update the PCCARD controller state */
  hpccard->State = HAL_PCCARD_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hpccard);  
  
  return HAL_OK;
}
/**
  * @brief Full-Duplex Transmit/Receive data in blocking mode.
  * @param  hi2s: pointer to a I2S_HandleTypeDef structure that contains
  *         the configuration information for I2S module
  * @param pTxData: a 16-bit pointer to the Transmit data buffer.
  * @param pRxData: a 16-bit pointer to the Receive data buffer.
  * @param Size: number of data sample to be sent:
  * @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
  *       configuration phase, the Size parameter means the number of 16-bit data length 
  *       in the transaction and when a 24-bit data frame or a 32-bit data frame is selected 
  *       the Size parameter means the number of 16-bit data length. 
  * @param Timeout: Timeout duration
  * @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization 
  *       between Master and Slave(example: audio streaming).
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_I2SEx_TransmitReceive(I2S_HandleTypeDef *hi2s, uint16_t *pTxData, uint16_t *pRxData, uint16_t Size, uint32_t Timeout)
{
  uint32_t tickstart = 0;
  uint32_t tmp1 = 0, tmp2 = 0;
 
  if((pTxData == NULL ) || (pRxData == NULL ) || (Size == 0)) 
  {
    return  HAL_ERROR;
  }

  /* Check the I2S State */
  if(hi2s->State == HAL_I2S_STATE_READY)
  {  
    tmp1 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN);
    tmp2 = hi2s->Instance->I2SCFGR & (SPI_I2SCFGR_DATLEN | SPI_I2SCFGR_CHLEN); 
    /* Check the Data format: When a 16-bit data frame or a 16-bit data frame extended 
       is selected during the I2S configuration phase, the Size parameter means the number
       of 16-bit data length in the transaction and when a 24-bit data frame or a 32-bit data 
       frame is selected the Size parameter means the number of 16-bit data length. */
    if((tmp1 == I2S_DATAFORMAT_24B)|| \
       (tmp2 == I2S_DATAFORMAT_32B))
    {
      hi2s->TxXferSize = Size*2;
      hi2s->TxXferCount = Size*2;
      hi2s->RxXferSize = Size*2;
      hi2s->RxXferCount = Size*2;
    }
    else
    {
      hi2s->TxXferSize = Size;
      hi2s->TxXferCount = Size;
      hi2s->RxXferSize = Size;
      hi2s->RxXferCount = Size;
    }
    
    /* Process Locked */
    __HAL_LOCK(hi2s);
    
    /* Set the I2S State busy TX/RX */
    hi2s->State = HAL_I2S_STATE_BUSY_TX_RX;
    
    tmp1 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    tmp2 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    /* Check if the I2S_MODE_MASTER_TX or I2S_MODE_SLAVE_TX Mode is selected */
    if((tmp1 == I2S_MODE_MASTER_TX) || (tmp2 == I2S_MODE_SLAVE_TX))
    { 
      /* Check if the I2S is already enabled: The I2S is kept enabled at the end of transaction
      to avoid the clock de-synchronization between Master and Slave. */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Enable I2Sext(receiver) before enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;

        /* Enable I2Sx peripheral */
        __HAL_I2S_ENABLE(hi2s);
      }
      
      while(hi2s->TxXferCount > 0)
      {
        /* Wait until TXE flag is set */
        if (I2S_WaitFlagStateUntilTimeout(hi2s, I2S_FLAG_TXE, RESET, Timeout) != HAL_OK)
        {
          return HAL_TIMEOUT;
        }
        hi2s->Instance->DR = (*pTxData++);

        /* Get tick */
        tickstart = HAL_GetTick();

        /* Wait until RXNE flag is set */
        while((I2SxEXT(hi2s->Instance)->SR & SPI_SR_RXNE) != SPI_SR_RXNE)
        {
          if(Timeout != HAL_MAX_DELAY)
          {
            if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
            {
              /* Process Unlocked */
              __HAL_UNLOCK(hi2s);

              return HAL_TIMEOUT;
            }
          }
        }
        (*pRxData++) = I2SxEXT(hi2s->Instance)->DR;
        
        hi2s->TxXferCount--;
        hi2s->RxXferCount--;
      }
    }
    /* The I2S_MODE_MASTER_RX or I2S_MODE_SLAVE_RX Mode is selected */
    else
    {
      /* Check if the I2S is already enabled */ 
      if((hi2s->Instance->I2SCFGR &SPI_I2SCFGR_I2SE) != SPI_I2SCFGR_I2SE)
      {
        /* Enable I2S peripheral before the I2Sext*/
        __HAL_I2S_ENABLE(hi2s);

        /* Enable I2Sext(transmitter) after enabling I2Sx peripheral */
        I2SxEXT(hi2s->Instance)->I2SCFGR |= SPI_I2SCFGR_I2SE;
      }
      else
      {
        /* Check if Master Receiver mode is selected */
        if((hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG) == I2S_MODE_MASTER_RX)
        {
          /* Clear the Overrun Flag by a read operation on the SPI_DR register followed by a read
          access to the SPI_SR register. */ 
          __HAL_I2S_CLEAR_OVRFLAG(hi2s);
        }
      }
      while(hi2s->TxXferCount > 0)
      {
        /* Get tick */
        tickstart = HAL_GetTick();

        /* Wait until TXE flag is set */
        while((I2SxEXT(hi2s->Instance)->SR & SPI_SR_TXE) != SPI_SR_TXE)
        {
          if(Timeout != HAL_MAX_DELAY)
          {
            if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout))
            {
              /* Process Unlocked */
              __HAL_UNLOCK(hi2s);

              return HAL_TIMEOUT;
            }
          }
        }
        I2SxEXT(hi2s->Instance)->DR = (*pTxData++);
        
        /* Wait until RXNE flag is set */
        if (I2S_WaitFlagStateUntilTimeout(hi2s, I2S_FLAG_RXNE, RESET, Timeout) != HAL_OK)
        {
          return HAL_TIMEOUT;
        }
        (*pRxData++) = hi2s->Instance->DR;

        hi2s->TxXferCount--;
        hi2s->RxXferCount--;
      }
    }

    /* Set the I2S State ready */
    hi2s->State = HAL_I2S_STATE_READY; 

    /* Process Unlocked */
    __HAL_UNLOCK(hi2s);
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
示例#12
0
/**
  * @brief  Writes a half-word buffer to the FSMC NOR memory. This function 
  *         must be used only with S29GL128P NOR memory. 
  * @param  hnor: pointer to a NOR_HandleTypeDef structure that contains
  *                the configuration information for NOR module.
  * @param  uwAddress: NOR memory internal address from which the data 
  * @note   Some NOR memory need Address aligned to xx bytes (can be aligned to 
  *          64 bytes boundary for example).
  * @param  pData: pointer to source data buffer. 
  * @param  uwBufferSize: number of Half words to write. 
  * @note   The maximum buffer size allowed is NOR memory dependent
  *         (can be 64 Bytes max for example).
  * @retval HAL status
  */ 
HAL_StatusTypeDef HAL_NOR_ProgramBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData, uint32_t uwBufferSize)
{
  uint16_t * p_currentaddress = (uint16_t *)NULL;
  uint16_t * p_endaddress = (uint16_t *)NULL;
  uint32_t lastloadedaddress = 0, deviceaddress = 0;
  
  /* Process Locked */
  __HAL_LOCK(hnor);
  
  /* Check the NOR controller state */
  if(hnor->State == HAL_NOR_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Select the NOR device address */
  if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
  {
    deviceaddress = NOR_MEMORY_ADRESS1;
  }
  else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
  {
    deviceaddress = NOR_MEMORY_ADRESS2;
  }
  else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
  {
    deviceaddress = NOR_MEMORY_ADRESS3;
  }
  else /* FSMC_NORSRAM_BANK4 */
  {
    deviceaddress = NOR_MEMORY_ADRESS4;
  }  
    
  /* Update the NOR controller state */
  hnor->State = HAL_NOR_STATE_BUSY;
  
  /* Initialize variables */
  p_currentaddress  = (uint16_t*)((uint32_t)(uwAddress));
  p_endaddress      = p_currentaddress + (uwBufferSize-1);
  lastloadedaddress = (uint32_t)(uwAddress);

  /* Issue unlock command sequence */
  NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
  NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND); 

  /* Write Buffer Load Command */
  NOR_WRITE((uint32_t)(p_currentaddress), NOR_CMD_DATA_BUFFER_AND_PROG); 
  NOR_WRITE((uint32_t)(p_currentaddress), (uwBufferSize-1)); 

  /* Load Data into NOR Buffer */
  while(p_currentaddress <= p_endaddress)
  {
    /* Store last loaded address & data value (for polling) */
    lastloadedaddress = (uint32_t)p_currentaddress;
 
    NOR_WRITE(p_currentaddress, *pData++);
    
    p_currentaddress++;
  }

  NOR_WRITE((uint32_t)(lastloadedaddress), NOR_CMD_DATA_BUFFER_AND_PROG_CONFIRM); 
  
  /* Check the NOR controller state */
  hnor->State = HAL_NOR_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnor);
  
  return HAL_OK; 
  
}
示例#13
0
/**
  * @brief Send data in interrupt mode 
  * @param hcec: CEC handle. 
  *         Function called under interruption only, once
  *         interruptions have been enabled by HAL_CEC_Transmit_IT()   
  * @retval HAL status
  */  
static HAL_StatusTypeDef CEC_Transmit_IT(CEC_HandleTypeDef *hcec)
{
  /* if the IP is already busy or if there is a previous transmission
     already pending due to arbitration loss */
  if ((hcec->State == HAL_CEC_STATE_BUSY_TX)
        || (__HAL_CEC_GET_TRANSMISSION_START_FLAG(hcec) != RESET))
  {
    __HAL_LOCK(hcec);
    /* set state to BUSY TX, in case it wasn't set already (case
     * of transmission new attempt after arbitration loss) */
    if (hcec->State != HAL_CEC_STATE_BUSY_TX)
    {
      hcec->State = HAL_CEC_STATE_BUSY_TX;
    }

    /* if all data have been sent */
    if(hcec->TxXferCount == 0)
    {
      /* Disable Peripheral to write CEC_IER register */
      __HAL_CEC_DISABLE(hcec);
      
      /* Disable the CEC Transmission Interrupts */
      __HAL_CEC_DISABLE_IT(hcec, CEC_IT_TXBR|CEC_IT_TXEND);
      /* Disable the CEC Transmission Error Interrupts */
      __HAL_CEC_DISABLE_IT(hcec, CEC_IER_TX_ALL_ERR);
      
      /* Enable the Peripheral */
      __HAL_CEC_ENABLE(hcec);
    
      __HAL_CEC_CLEAR_FLAG(hcec,CEC_FLAG_TXBR|CEC_FLAG_TXEND);
          
      hcec->State = HAL_CEC_STATE_READY;
      /* Call the Process Unlocked before calling the Tx call back API to give the possibility to
      start again the Transmission under the Tx call back API */
      __HAL_UNLOCK(hcec);
      
      HAL_CEC_TxCpltCallback(hcec);
      
      return HAL_OK;
    }
    else
    {
      if (hcec->TxXferCount == 1)
      {
        /* if this is the last byte transmission, set TX End of Message (TXEOM) bit */
        __HAL_CEC_LAST_BYTE_TX_SET(hcec);
      }
      /* clear Tx-Byte request flag */
       __HAL_CEC_CLEAR_FLAG(hcec,CEC_FLAG_TXBR); 
       hcec->Instance->TXDR = *hcec->pTxBuffPtr++;
      hcec->TxXferCount--;
      
      /* Process Unlocked */
      __HAL_UNLOCK(hcec);
  
      return HAL_OK;
    }
  }
  else
  {
    return HAL_BUSY;   
  }
}
示例#14
0
/**
  * @brief Send data in interrupt mode 
  * @param hcec: CEC handle 
  * @param DestinationAddress: destination logical address      
  * @param pData: pointer to input byte data buffer
  * @param Size: amount of data to be sent in bytes (without counting the header).
  *              0 means only the header is sent (ping operation).
  *              Maximum TX size is 15 bytes (1 opcode and up to 14 operands).    
  * @retval HAL status
  */  
HAL_StatusTypeDef HAL_CEC_Transmit_IT(CEC_HandleTypeDef *hcec, uint8_t DestinationAddress, uint8_t *pData, uint32_t Size)
{
  uint8_t  temp = 0; 
  /* if the IP isn't already busy and if there is no previous transmission
     already pending due to arbitration lost */
  if (((hcec->State == HAL_CEC_STATE_READY) || (hcec->State == HAL_CEC_STATE_STANDBY_RX)) 
  &&   (__HAL_CEC_GET_TRANSMISSION_START_FLAG(hcec) == RESET)) 
  {    
    if((pData == NULL ) && (Size > 0)) 
    {
      hcec->State = HAL_CEC_STATE_ERROR;
      return  HAL_ERROR;                                    
    }

    assert_param(IS_CEC_ADDRESS(DestinationAddress)); 
    assert_param(IS_CEC_MSGSIZE(Size));
    
    /* Process Locked */
    __HAL_LOCK(hcec);
    hcec->pTxBuffPtr = pData;
    hcec->State = HAL_CEC_STATE_BUSY_TX;
    hcec->ErrorCode = HAL_CEC_ERROR_NONE;
    
    /* Disable Peripheral to write CEC_IER register */
    __HAL_CEC_DISABLE(hcec);
    
    /* Enable the following two CEC Transmission interrupts as
     * well as the following CEC Transmission Errors interrupts: 
     * Tx Byte Request IT 
     * End of Transmission IT
     * Tx Missing Acknowledge IT
     * Tx-Error IT
     * Tx-Buffer Underrun IT 
     * Tx arbitration lost     */
    __HAL_CEC_ENABLE_IT(hcec, CEC_IT_TXBR|CEC_IT_TXEND|CEC_IER_TX_ALL_ERR);
                                     
    /* Enable the Peripheral */
    __HAL_CEC_ENABLE(hcec);
  
    /* initialize the number of bytes to send,
     * 0 means only one header is sent (ping operation) */
    hcec->TxXferCount = Size;
    
    /* Process Unlocked */
    __HAL_UNLOCK(hcec); 
    
    /* in case of no payload (Size = 0), sender is only pinging the system;
     * Set TX End of Message (TXEOM) bit, must be set before writing data to TXDR */
    if (Size == 0)
    {
      __HAL_CEC_LAST_BYTE_TX_SET(hcec);
    }
    
    /* send header block */
    temp = ((uint32_t)hcec->Init.InitiatorAddress << CEC_INITIATOR_LSB_POS) | DestinationAddress;
    hcec->Instance->TXDR = temp;
    /* Set TX Start of Message  (TXSOM) bit */
    __HAL_CEC_FIRST_BYTE_TX_SET(hcec);
    
    return HAL_OK;
  }
    /* if the IP is already busy or if there is a previous transmission
     already pending due to arbitration loss */
  else if ((hcec->State == HAL_CEC_STATE_BUSY_TX)
        || (__HAL_CEC_GET_TRANSMISSION_START_FLAG(hcec) != RESET))
  {
    __HAL_LOCK(hcec);
    /* set state to BUSY TX, in case it wasn't set already (case
     * of transmission new attempt after arbitration loss) */
    if (hcec->State != HAL_CEC_STATE_BUSY_TX)
    {
      hcec->State = HAL_CEC_STATE_BUSY_TX;
    }

    /* if all data have been sent */
    if(hcec->TxXferCount == 0)
    {
      /* Disable Peripheral to write CEC_IER register */
      __HAL_CEC_DISABLE(hcec);
      
      /* Disable the CEC Transmission Interrupts */
      __HAL_CEC_DISABLE_IT(hcec, CEC_IT_TXBR|CEC_IT_TXEND);
      /* Disable the CEC Transmission Error Interrupts */
      __HAL_CEC_DISABLE_IT(hcec, CEC_IER_TX_ALL_ERR);
      
      /* Enable the Peripheral */
      __HAL_CEC_ENABLE(hcec);
    
      __HAL_CEC_CLEAR_FLAG(hcec, CEC_FLAG_TXBR|CEC_FLAG_TXEND);
          
      hcec->State = HAL_CEC_STATE_READY;
      /* Call the Process Unlocked before calling the Tx call back API to give the possibility to
      start again the Transmission under the Tx call back API */
      __HAL_UNLOCK(hcec);
      
      HAL_CEC_TxCpltCallback(hcec);
      
      return HAL_OK;
    }
    else
    {
      if (hcec->TxXferCount == 1)
      {
        /* if this is the last byte transmission, set TX End of Message (TXEOM) bit */
        __HAL_CEC_LAST_BYTE_TX_SET(hcec);
      }
      /* clear Tx-Byte request flag */
       __HAL_CEC_CLEAR_FLAG(hcec, CEC_FLAG_TXBR); 
       hcec->Instance->TXDR = *hcec->pTxBuffPtr++;
      hcec->TxXferCount--;
      
      /* Process Unlocked */
      __HAL_UNLOCK(hcec);
  
      return HAL_OK;
    }
  }
  else
  {
    return HAL_BUSY;   
  }
}
/**
  * @brief  Enables the interrupt and starts ADC conversion of regular channels.
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  * @retval HAL status.
  */
HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc)
{
  uint16_t i = 0;
  
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
  assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
  
  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* Check if an injected conversion is ongoing */
  if(hadc->State == HAL_ADC_STATE_BUSY_INJ)
  {
    /* Change ADC state */
    hadc->State = HAL_ADC_STATE_BUSY_INJ_REG;  
  }
  else
  {
    /* Change ADC state */
    hadc->State = HAL_ADC_STATE_BUSY_REG;
  } 
  
  /* Set ADC error code to none */
  hadc->ErrorCode = HAL_ADC_ERROR_NONE;
  
  /* Check if ADC peripheral is disabled in order to enable it and wait during 
     Tstab time the ADC's stabilization */
  if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
  {  
    /* Enable the Peripheral */
    __HAL_ADC_ENABLE(hadc);
    
    /* Delay inserted to wait during Tstab time the ADC's stabilization */
    for(; i <= 540; i++)
    {
      __NOP();
    }
  }
  
  /* Enable the ADC overrun interrupt */
  __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
  
  /* Enable the ADC end of conversion interrupt for regular group */
  __HAL_ADC_ENABLE_IT(hadc, ADC_IT_EOC);
  
  /* Check if Multimode enabled */
  if(HAL_IS_BIT_CLR(ADC->CCR, ADC_CCR_MULTI))
  {
    /* if no external trigger present enable software conversion of regular channels */
    if (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE)
    {
      /* Enable the selected ADC software conversion for regular group */
      hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
    }
  }
  else
  {
    /* if instance of handle correspond to ADC1 and  no external trigger present enable software conversion of regular channels */
    if ((hadc->Instance == (ADC_TypeDef*)0x40012000) && (hadc->Init.ExternalTrigConvEdge == ADC_EXTERNALTRIGCONVEDGE_NONE))
    {
      /* Enable the selected ADC software conversion for regular group */
        hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
    }
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief Full-Duplex Transmit/Receive data in non-blocking mode using Interrupt 
  * @param  hi2s: pointer to a I2S_HandleTypeDef structure that contains
  *         the configuration information for I2S module
  * @retval HAL status
  */
HAL_StatusTypeDef I2SEx_TransmitReceive_IT(I2S_HandleTypeDef *hi2s)
{
  uint32_t tmp1 = 0, tmp2 = 0;
  
  if(hi2s->State == HAL_I2S_STATE_BUSY_TX_RX)
  {
    /* Process Locked */
    __HAL_LOCK(hi2s);

    tmp1 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    tmp2 = hi2s->Instance->I2SCFGR & SPI_I2SCFGR_I2SCFG;
    /* Check if the I2S_MODE_MASTER_TX or I2S_MODE_SLAVE_TX Mode is selected */
    if((tmp1 == I2S_MODE_MASTER_TX) || (tmp2 == I2S_MODE_SLAVE_TX))
    {
      if(hi2s->TxXferCount != 0)
      {
        if(__HAL_I2S_GET_FLAG(hi2s, I2S_FLAG_TXE) != RESET)
        {        
          /* Transmit data */
          hi2s->Instance->DR = (*hi2s->pTxBuffPtr++);
          hi2s->TxXferCount--;

          if(hi2s->TxXferCount == 0)
          {
            /* Disable TXE interrupt */
            __HAL_I2S_DISABLE_IT(hi2s, I2S_IT_TXE);
          }
        }
      }

      if(hi2s->RxXferCount != 0)
      {
        if((I2SxEXT(hi2s->Instance)->SR & SPI_SR_RXNE) == SPI_SR_RXNE)
        {
          /* Receive data */
          (*hi2s->pRxBuffPtr++) = I2SxEXT(hi2s->Instance)->DR;
          hi2s->RxXferCount--;

          if(hi2s->RxXferCount == 0)
          {
            /* Disable I2Sext RXNE interrupt */
            I2SxEXT(hi2s->Instance)->CR2 &= ~I2S_IT_RXNE;
          }
        }
      }
    }
    /* The I2S_MODE_MASTER_RX or I2S_MODE_SLAVE_RX Mode is selected */ 
    else
    {
      if(hi2s->TxXferCount != 0)
      {
        if((I2SxEXT(hi2s->Instance)->SR & SPI_SR_TXE) == SPI_SR_TXE)
        {        
          /* Transmit data */
          I2SxEXT(hi2s->Instance)->DR = (*hi2s->pTxBuffPtr++);
          hi2s->TxXferCount--;

          if(hi2s->TxXferCount == 0)
          {
            /* Disable I2Sext TXE interrupt */
            I2SxEXT(hi2s->Instance)->CR2 &= ~I2S_IT_TXE;

            HAL_I2S_TxCpltCallback(hi2s);
          }
        }
      }
      if(hi2s->RxXferCount != 0)
      {
        if(__HAL_I2S_GET_FLAG(hi2s, I2S_FLAG_RXNE) != RESET)
        {
          /* Receive data */
          (*hi2s->pRxBuffPtr++) = hi2s->Instance->DR;
          hi2s->RxXferCount--;

          if(hi2s->RxXferCount == 0)
          {
            /* Disable RXNE interrupt */
            __HAL_I2S_DISABLE_IT(hi2s, I2S_IT_RXNE);

            HAL_I2S_RxCpltCallback(hi2s);
          }
        }
      }
    }

    tmp1 = hi2s->RxXferCount;
    tmp2 = hi2s->TxXferCount;
    if((tmp1 == 0) && (tmp2 == 0))
    {
      /* Disable I2Sx ERR interrupt */
      __HAL_I2S_DISABLE_IT(hi2s, I2S_IT_ERR);
      /* Disable I2Sext ERR interrupt */
      I2SxEXT(hi2s->Instance)->CR2 &= ~I2S_IT_ERR;
      
      hi2s->State = HAL_I2S_STATE_READY; 
    }

    /* Process Unlocked */
    __HAL_UNLOCK(hi2s);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY; 
  }
}
  /**
  * @brief  Configures for the selected ADC regular channel its corresponding
  *         rank in the sequencer and its sample time.
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  * @param  sConfig: ADC configuration structure. 
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig)
{
  /* Check the parameters */
  assert_param(IS_ADC_CHANNEL(sConfig->Channel));
  assert_param(IS_ADC_REGULAR_RANK(sConfig->Rank));
  assert_param(IS_ADC_SAMPLE_TIME(sConfig->SamplingTime));
  
  /* Process locked */
  __HAL_LOCK(hadc);
    
  /* if ADC_Channel_10 ... ADC_Channel_18 is selected */
  if (sConfig->Channel > ADC_CHANNEL_9)
  {
    /* Clear the old sample time */
    hadc->Instance->SMPR1 &= ~ADC_SMPR1(ADC_SMPR1_SMP10, sConfig->Channel);
    
    /* Set the new sample time */
    hadc->Instance->SMPR1 |= ADC_SMPR1(sConfig->SamplingTime, sConfig->Channel);
  }
  else /* ADC_Channel include in ADC_Channel_[0..9] */
  {
    /* Clear the old sample time */
    hadc->Instance->SMPR2 &= ~ADC_SMPR2(ADC_SMPR2_SMP0, sConfig->Channel);
    
    /* Set the new sample time */
    hadc->Instance->SMPR2 |= ADC_SMPR2(sConfig->SamplingTime, sConfig->Channel);
  }
  
  /* For Rank 1 to 6 */
  if (sConfig->Rank < 7)
  {
    /* Clear the old SQx bits for the selected rank */
    hadc->Instance->SQR3 &= ~ADC_SQR3_RK(ADC_SQR3_SQ1, sConfig->Rank);
    
    /* Set the SQx bits for the selected rank */
    hadc->Instance->SQR3 |= ADC_SQR3_RK(sConfig->Channel, sConfig->Rank);
  }
  /* For Rank 7 to 12 */
  else if (sConfig->Rank < 13)
  {
    /* Clear the old SQx bits for the selected rank */
    hadc->Instance->SQR2 &= ~ADC_SQR2_RK(ADC_SQR2_SQ7, sConfig->Rank);
    
    /* Set the SQx bits for the selected rank */
    hadc->Instance->SQR2 |= ADC_SQR2_RK(sConfig->Channel, sConfig->Rank);
  }
  /* For Rank 13 to 16 */
  else
  {
    /* Clear the old SQx bits for the selected rank */
    hadc->Instance->SQR1 &= ~ADC_SQR1_RK(ADC_SQR1_SQ13, sConfig->Rank);
    
    /* Set the SQx bits for the selected rank */
    hadc->Instance->SQR1 |= ADC_SQR1_RK(sConfig->Channel, sConfig->Rank);
  }
  
  /* if ADC1 Channel_18 is selected enable VBAT Channel */
  if ((hadc->Instance == ADC1) && (sConfig->Channel == ADC_CHANNEL_VBAT))
  {
    /* Enable the VBAT channel*/
    ADC->CCR |= ADC_CCR_VBATE;
  }
  
  /* if ADC1 Channel_16 or Channel_17 is selected enable TSVREFE Channel(Temperature sensor and VREFINT) */
  if ((hadc->Instance == ADC1) && ((sConfig->Channel == ADC_CHANNEL_TEMPSENSOR) || (sConfig->Channel == ADC_CHANNEL_VREFINT)))
  {
    /* Enable the TSVREFE channel*/
    ADC->CCR |= ADC_CCR_TSVREFE;
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief  Read Spare area(s) from NAND memory 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer: pointer to source buffer to write  
  * @param  NumSpareAreaToRead: Number of spare area to read  
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_NAND_Read_SpareArea(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaToRead)
{
  __IO uint32_t index   = 0; 
  uint32_t deviceaddress = 0, size = 0, num_spare_area_read = 0, addressstatus = NAND_VALID_ADDRESS;
  NAND_AddressTypeDef nandaddress;
  uint32_t addressoffset = 0;
  
  /* Process Locked */
  __HAL_LOCK(hnand);  
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;
  
  /* Save the content of pAddress as it will be modified */
  nandaddress.Block     = pAddress->Block;
  nandaddress.Page      = pAddress->Page;
  nandaddress.Zone      = pAddress->Zone;
  
  /* Spare area(s) read loop */ 
  while((NumSpareAreaToRead != 0) && (addressstatus == NAND_VALID_ADDRESS))
  {     
    /* update the buffer size */
    size = (hnand->Info.SpareAreaSize) + ((hnand->Info.SpareAreaSize) * num_spare_area_read);

    /* Get the address offset */
    addressoffset = ARRAY_ADDRESS(&nandaddress, hnand);
    
    /* Send read spare area command sequence */     
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;

    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00; 
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(addressoffset);
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(addressoffset);
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(addressoffset);
  
    /* for 512 and 1 GB devices, 4th cycle is required */    
    if(hnand->Info.BlockNbr >= 1024)
    {
      *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_4TH_CYCLE(addressoffset);
    } 

    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_TRUE1;
    
    /* Get Data into Buffer */
    for (index = size ;index != 0; index--)
    {
      *(uint8_t *)pBuffer++ = *(uint8_t *)deviceaddress;
    }
    
    /* Increment read spare areas number */
    num_spare_area_read++;
    
    /* Decrement spare areas to read */
    NumSpareAreaToRead--;
    
    /* Increment the NAND address */
    addressstatus = HAL_NAND_Address_Inc(hnand, &nandaddress);
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnand);

  return HAL_OK;  
}
/**
  * @brief  Enables ADC DMA request after last transfer (Multi-ADC mode) and enables ADC peripheral
  * 
  * @note   Caution: This function must be used only with the ADC master.  
  *
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  * @param  pData:   Pointer to buffer in which transferred from ADC peripheral to memory will be stored. 
  * @param  Length:  The length of data to be transferred from ADC peripheral to memory.  
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ADCEx_MultiModeStart_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
{
  __IO uint32_t counter = 0;
  
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
  assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
  assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DMAContinuousRequests));
  
  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* Enable ADC overrun interrupt */
  __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
  
  if (hadc->Init.DMAContinuousRequests != DISABLE)
  {
    /* Enable the selected ADC DMA request after last transfer */
    ADC->CCR |= ADC_CCR_DDS;
  }
  else
  {
    /* Disable the selected ADC EOC rising on each regular channel conversion */
    ADC->CCR &= ~ADC_CCR_DDS;
  }
  
  /* Set the DMA transfer complete callback */
  hadc->DMA_Handle->XferCpltCallback = ADC_MultiModeDMAConvCplt;
  
  /* Set the DMA half transfer complete callback */
  hadc->DMA_Handle->XferHalfCpltCallback = ADC_MultiModeDMAHalfConvCplt;
     
  /* Set the DMA error callback */
  hadc->DMA_Handle->XferErrorCallback = ADC_MultiModeDMAError ;
  
  /* Enable the DMA Stream */
  HAL_DMA_Start_IT(hadc->DMA_Handle, (uint32_t)&ADC->CDR, (uint32_t)pData, Length);
  
  /* Change ADC state */
  hadc->State = HAL_ADC_STATE_BUSY_REG;
  
  /* Check if ADC peripheral is disabled in order to enable it and wait during 
     Tstab time the ADC's stabilization */
  if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
  {  
    /* Enable the Peripheral */
    __HAL_ADC_ENABLE(hadc);
    
    /* Delay for temperature sensor stabilization time */
    /* Compute number of CPU cycles to wait for */
    counter = (ADC_STAB_DELAY_US * (SystemCoreClock / 1000000));
    while(counter != 0)
    {
      counter--;
    }
  }
  
  /* if no external trigger present enable software conversion of regular channels */
  if((hadc->Instance->CR2 & ADC_CR2_EXTEN) == RESET) 
  {
    /* Enable the selected ADC software conversion for regular group */
    hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
  }
  
  /* Process unlocked */
  __HAL_UNLOCK(hadc);
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief  Write Spare area(s) to NAND memory 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @param  pBuffer : pointer to source buffer to write  
  * @param  NumSpareAreaTowrite  : number of spare areas to write to block
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Write_SpareArea(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer, uint32_t NumSpareAreaTowrite)
{
  __IO uint32_t index = 0;
  uint32_t tickstart = 0;
  uint32_t deviceaddress = 0, size = 0, num_spare_area_written = 0, addressstatus = NAND_VALID_ADDRESS;
  NAND_AddressTypeDef nandaddress;
  uint32_t addressoffset = 0;

  /* Process Locked */
  __HAL_LOCK(hnand); 
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the FMC_NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Save the content of pAddress as it will be modified */
  nandaddress.Block     = pAddress->Block;
  nandaddress.Page      = pAddress->Page;
  nandaddress.Zone      = pAddress->Zone;
  
  /* Spare area(s) write loop */
  while((NumSpareAreaTowrite != 0) && (addressstatus == NAND_VALID_ADDRESS))
  {
    /* update the buffer size */
    size = (hnand->Info.SpareAreaSize) + ((hnand->Info.SpareAreaSize) * num_spare_area_written);

    /* Get the address offset */
    addressoffset = ARRAY_ADDRESS(&nandaddress, hnand);
    
    /* Send write Spare area command sequence */
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_AREA_C;
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE0;

    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = 0x00;  
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(addressoffset);
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(addressoffset);
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(addressoffset);
  
    /* for 512 and 1 GB devices, 4th cycle is required */     
    if(hnand->Info.BlockNbr >= 1024)
    {
      *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_4TH_CYCLE(addressoffset);
    }
  
    /* Write data to memory */
    for(; index < size; index++)
    {
      *(__IO uint8_t *)deviceaddress = *(uint8_t *)pBuffer++;
    }
   
    *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_WRITE_TRUE1;
    
    /* Get tick */
    tickstart = HAL_GetTick();
    
    /* Read status until NAND is ready */
    while(HAL_NAND_Read_Status(hnand) != NAND_READY)
    {
      if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
      {
        return HAL_TIMEOUT; 
      }
    }

    /* Increment written spare areas number */
    num_spare_area_written++;
    
    /* Decrement spare areas to write */
    NumSpareAreaTowrite--;
    
    /* Increment the NAND address */
    addressstatus = HAL_NAND_Address_Inc(hnand, &nandaddress);
  }

  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;

  /* Process unlocked */
  __HAL_UNLOCK(hnand);
    
  return HAL_OK;
}
示例#21
0
/**
  * @brief  Enables ADC DMA request after last transfer (Multi-ADC mode) and enables ADC peripheral
  * 
  * @note   Caution: This function must be used only with the ADC master.  
  *
  * @param  hadc: pointer to a ADC_HandleTypeDef structure that contains
  *         the configuration information for the specified ADC.
  * @param  pData:   Pointer to buffer in which transferred from ADC peripheral to memory will be stored. 
  * @param  Length:  The length of data to be transferred from ADC peripheral to memory.  
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_ADCEx_MultiModeStart_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
{
  __IO uint32_t counter = 0;
  
  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
  assert_param(IS_ADC_EXT_TRIG_EDGE(hadc->Init.ExternalTrigConvEdge));
  assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DMAContinuousRequests));
  
  /* Process locked */
  __HAL_LOCK(hadc);
  
  /* Check if ADC peripheral is disabled in order to enable it and wait during 
     Tstab time the ADC's stabilization */
  if((hadc->Instance->CR2 & ADC_CR2_ADON) != ADC_CR2_ADON)
  {  
    /* Enable the Peripheral */
    __HAL_ADC_ENABLE(hadc);
    
    /* Delay for temperature sensor stabilization time */
    /* Compute number of CPU cycles to wait for */
    counter = (ADC_STAB_DELAY_US * (SystemCoreClock / 1000000));
    while(counter != 0)
    {
      counter--;
    }
  }
  
  /* Start conversion if ADC is effectively enabled */
  if(HAL_IS_BIT_SET(hadc->Instance->CR2, ADC_CR2_ADON))
  {
    /* Set ADC state                                                          */
    /* - Clear state bitfield related to regular group conversion results     */
    /* - Set state bitfield related to regular group operation                */
    ADC_STATE_CLR_SET(hadc->State,
                      HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR,
                      HAL_ADC_STATE_REG_BUSY);
    
    /* If conversions on group regular are also triggering group injected,    */
    /* update ADC state.                                                      */
    if (READ_BIT(hadc->Instance->CR1, ADC_CR1_JAUTO) != RESET)
    {
      ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);  
    }
    
    /* State machine update: Check if an injected conversion is ongoing */
    if (HAL_IS_BIT_SET(hadc->State, HAL_ADC_STATE_INJ_BUSY))
    {
      /* Reset ADC error code fields related to conversions on group regular */
      CLEAR_BIT(hadc->ErrorCode, (HAL_ADC_ERROR_OVR | HAL_ADC_ERROR_DMA));         
    }
    else
    {
      /* Reset ADC all error code fields */
      ADC_CLEAR_ERRORCODE(hadc);
    }
    
    /* Process unlocked */
    /* Unlock before starting ADC conversions: in case of potential           */
    /* interruption, to let the process to ADC IRQ Handler.                   */
    __HAL_UNLOCK(hadc);
    
    /* Set the DMA transfer complete callback */
    hadc->DMA_Handle->XferCpltCallback = ADC_MultiModeDMAConvCplt;
    
    /* Set the DMA half transfer complete callback */
    hadc->DMA_Handle->XferHalfCpltCallback = ADC_MultiModeDMAHalfConvCplt;
    
    /* Set the DMA error callback */
    hadc->DMA_Handle->XferErrorCallback = ADC_MultiModeDMAError ;
    
    /* Manage ADC and DMA start: ADC overrun interruption, DMA start, ADC     */
    /* start (in case of SW start):                                           */
    
    /* Clear regular group conversion flag and overrun flag */
    /* (To ensure of no unknown state from potential previous ADC operations) */
    __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_EOC);

    /* Enable ADC overrun interrupt */
    __HAL_ADC_ENABLE_IT(hadc, ADC_IT_OVR);
    
    if (hadc->Init.DMAContinuousRequests != DISABLE)
    {
      /* Enable the selected ADC DMA request after last transfer */
      ADC->CCR |= ADC_CCR_DDS;
    }
    else
    {
      /* Disable the selected ADC EOC rising on each regular channel conversion */
      ADC->CCR &= ~ADC_CCR_DDS;
    }
    
    /* Enable the DMA Stream */
    HAL_DMA_Start_IT(hadc->DMA_Handle, (uint32_t)&ADC->CDR, (uint32_t)pData, Length);
    
    /* if no external trigger present enable software conversion of regular channels */
    if((hadc->Instance->CR2 & ADC_CR2_EXTEN) == RESET) 
    {
      /* Enable the selected ADC software conversion for regular group */
      hadc->Instance->CR2 |= (uint32_t)ADC_CR2_SWSTART;
    }
  }
  
  /* Return function status */
  return HAL_OK;
}
/**
  * @brief  NAND memory Block erase 
  * @param  hnand: pointer to a NAND_HandleTypeDef structure that contains
  *                the configuration information for NAND module.
  * @param  pAddress : pointer to NAND address structure
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_NAND_Erase_Block(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress)
{
  uint32_t deviceaddress = 0;
  uint32_t tickstart = 0;
  
  /* Process Locked */
  __HAL_LOCK(hnand);
  
  /* Check the NAND controller state */
  if(hnand->State == HAL_NAND_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Identify the device address */
  if(hnand->Init.NandBank == FMC_NAND_BANK2)
  {
    deviceaddress = NAND_DEVICE1;
  }
  else
  {
    deviceaddress = NAND_DEVICE2;
  }
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_BUSY;  
  
  /* Send Erase block command sequence */
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE0;

  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_1ST_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_2ND_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_3RD_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  
  /* for 512 and 1 GB devices, 4th cycle is required */     
  if(hnand->Info.BlockNbr >= 1024)
  {
    *(__IO uint8_t *)((uint32_t)(deviceaddress | ADDR_AREA)) = ADDR_4TH_CYCLE(ARRAY_ADDRESS(pAddress, hnand));
  }  
    
  *(__IO uint8_t *)((uint32_t)(deviceaddress | CMD_AREA)) = NAND_CMD_ERASE1; 
  
  /* Update the NAND controller state */
  hnand->State = HAL_NAND_STATE_READY;
  
  /* Get tick */
  tickstart = HAL_GetTick();
  
  /* Read status until NAND is ready */
  while(HAL_NAND_Read_Status(hnand) != NAND_READY)
  {
    if((HAL_GetTick() - tickstart ) > NAND_WRITE_TIMEOUT)
    {
      /* Process unlocked */
      __HAL_UNLOCK(hnand);    
  
      return HAL_TIMEOUT; 
    } 
  }    
 
  /* Process unlocked */
  __HAL_UNLOCK(hnand);    
  
  return HAL_OK;  
}
示例#23
0
/**
  * @brief  Enables DCMI DMA request and enables DCMI capture
  * @param  hdcmi:     pointer to a DCMI_HandleTypeDef structure that contains
  *                    the configuration information for DCMI.
  * @param  DCMI_Mode: DCMI capture mode snapshot or continuous grab.
  * @param  pData:     The destination memory Buffer address (LCD Frame buffer).
  * @param  Length:    The length of capture to be transferred.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DCMI_Start_DMA(DCMI_HandleTypeDef* hdcmi, uint32_t DCMI_Mode, uint32_t pData, uint32_t Length)
{
  /* Initialize the second memory address */
  uint32_t SecondMemAddress = 0;

  /* Check function parameters */
  assert_param(IS_DCMI_CAPTURE_MODE(DCMI_Mode));

  /* Process Locked */
  __HAL_LOCK(hdcmi);

  /* Lock the DCMI peripheral state */
  hdcmi->State = HAL_DCMI_STATE_BUSY;

  /* Check the parameters */
  assert_param(IS_DCMI_CAPTURE_MODE(DCMI_Mode));

  /* Configure the DCMI Mode */
  hdcmi->Instance->CR &= ~(DCMI_CR_CM);
  hdcmi->Instance->CR |=  (uint32_t)(DCMI_Mode);

  /* Set the DMA memory0 conversion complete callback */
  hdcmi->DMA_Handle->XferCpltCallback = DCMI_DMAConvCplt;

  /* Set the DMA error callback */
  hdcmi->DMA_Handle->XferErrorCallback = DCMI_DMAError;

  if(Length <= 0xFFFF)
  {
    /* Enable the DMA Stream */
    HAL_DMA_Start_IT(hdcmi->DMA_Handle, (uint32_t)&hdcmi->Instance->DR, (uint32_t)pData, Length);
  }
  else /* DCMI_DOUBLE_BUFFER Mode */
  {
    /* Set the DMA memory1 conversion complete callback */
    hdcmi->DMA_Handle->XferM1CpltCallback = DCMI_DMAConvCplt;

    /* Initialize transfer parameters */
    hdcmi->XferCount = 1;
    hdcmi->XferSize = Length;
    hdcmi->pBuffPtr = pData;

    /* Get the number of buffer */
    while(hdcmi->XferSize > 0xFFFF)
    {
      hdcmi->XferSize = (hdcmi->XferSize/2);
      hdcmi->XferCount = hdcmi->XferCount*2;
    }

    /* Update DCMI counter  and transfer number*/
    hdcmi->XferCount = (hdcmi->XferCount - 2);
    hdcmi->XferTransferNumber = hdcmi->XferCount;

    /* Update second memory address */
    SecondMemAddress = (uint32_t)(pData + (4*hdcmi->XferSize));

    /* Start DMA multi buffer transfer */
    HAL_DMAEx_MultiBufferStart_IT(hdcmi->DMA_Handle, (uint32_t)&hdcmi->Instance->DR, (uint32_t)pData, SecondMemAddress, hdcmi->XferSize);
  }

  /* Enable Capture */
  DCMI->CR |= DCMI_CR_CAPTURE;

  /* Return function status */
  return HAL_OK;
}
示例#24
0
/**
  * @brief  Writes a half-word buffer to the NOR memory. This function must be used 
            only with S29GL128P NOR memory. 
  * @param  hnor: pointer to the NOR handle
  * @param  uwAddress: NOR memory internal start write address 
  * @param  pData: pointer to source data buffer. 
  * @param  uwBufferSize: Size of the buffer to write
  * @retval HAL status
  */ 
HAL_StatusTypeDef HAL_NOR_ProgramBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData, uint32_t uwBufferSize)
{
  uint32_t lastloadedaddress = 0;
  uint32_t currentaddress = 0;
  uint32_t endaddress = 0;
  uint32_t deviceAddress = 0;
  
  /* Process Locked */
  __HAL_LOCK(hnor);
  
  /* Check the NOR controller state */
  if(hnor->State == HAL_NOR_STATE_BUSY)
  {
     return HAL_BUSY;
  }
  
  /* Select the NOR device address */
  if (hnor->Init.NSBank == FMC_NORSRAM_BANK1)
  {
    deviceAddress = NOR_MEMORY_ADRESS1;
  }
  else if (hnor->Init.NSBank == FMC_NORSRAM_BANK2)
  {
    deviceAddress = NOR_MEMORY_ADRESS2;
  }
  else if (hnor->Init.NSBank == FMC_NORSRAM_BANK3)
  {
    deviceAddress = NOR_MEMORY_ADRESS3;
  }
  else /* FMC_NORSRAM_BANK4 */
  {
    deviceAddress = NOR_MEMORY_ADRESS4;
  }  
    
  /* Update the NOR controller state */
  hnor->State = HAL_NOR_STATE_BUSY;
  
  /* Initialize variables */
  currentaddress    = uwAddress;
  endaddress        = uwAddress + uwBufferSize - 1;
  lastloadedaddress = uwAddress;

  /* Issue unlock command sequence */
  __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, 0x0555), 0x00AA);
  __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, 0x02AA), 0x0055); 

  /* Write Buffer Load Command */
  __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, uwAddress), 0x25); 
  __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, uwAddress), (uwBufferSize - 1)); 

  /* Load Data into NOR Buffer */
  while(currentaddress <= endaddress)
  {
    /* Store last loaded address & data value (for polling) */
    lastloadedaddress = currentaddress;
 
    __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, currentaddress), *pData++);
    
    currentaddress += 1; 
  }

  __NOR_WRITE(__NOR_ADDR_SHIFT(deviceAddress, NOR_MEMORY_8B, lastloadedaddress), 0x29); 
  
  /* Check the NOR controller state */
  hnor->State = HAL_NOR_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hnor);
  
  return HAL_OK; 
  
}
示例#25
0
/**
  * @brief  Configures the selected DAC channel.
  * @param  hdac: pointer to a DAC_HandleTypeDef structure that contains
  *         the configuration information for the specified DAC.
  * @param  sConfig: DAC configuration structure.
  * @param  Channel: The selected DAC channel. 
  *          This parameter can be one of the following values:
  *            @arg DAC_CHANNEL_1: DAC Channel1 selected
  *            @arg DAC_CHANNEL_2: DAC Channel2 selected
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DAC_ConfigChannel(DAC_HandleTypeDef* hdac, DAC_ChannelConfTypeDef* sConfig, uint32_t Channel)
{
  uint32_t tmpreg1 = 0, tmpreg2 = 0;
  uint32_t tickstart = 0;
   
  /* Check the DAC parameters */
  assert_param(IS_DAC_TRIGGER(sConfig->DAC_Trigger));
  assert_param(IS_DAC_OUTPUT_BUFFER_STATE(sConfig->DAC_OutputBuffer));
  assert_param(IS_DAC_CHIP_CONNECTION(sConfig->DAC_ConnectOnChipPeripheral));
  assert_param(IS_DAC_TRIMMING(sConfig->DAC_UserTrimming));
  if ((sConfig->DAC_UserTrimming) == DAC_TRIMMING_USER)
  {
    assert_param(IS_DAC_TRIMMINGVALUE(sConfig->DAC_TrimmingValue));               
  }
  assert_param(IS_DAC_SAMPLEANDHOLD(sConfig->DAC_SampleAndHold));
  if ((sConfig->DAC_SampleAndHold) == DAC_SAMPLEANDHOLD_ENABLE)
  {
    assert_param(IS_DAC_SAMPLETIME(sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime));
    assert_param(IS_DAC_HOLDTIME(sConfig->DAC_SampleAndHoldConfig.DAC_HoldTime));
    assert_param(IS_DAC_REFRESHTIME(sConfig->DAC_SampleAndHoldConfig.DAC_RefreshTime)); 
  }
  assert_param(IS_DAC_CHANNEL(Channel));
 
  /* Process locked */
  __HAL_LOCK(hdac);
  
  /* Change DAC state */
  hdac->State = HAL_DAC_STATE_BUSY;
  
  if(sConfig->DAC_SampleAndHold == DAC_SAMPLEANDHOLD_ENABLE)
  /* Sample on old configuration */ 
  {
    /* SampleTime */
    if (Channel == DAC_CHANNEL_1)
    {
      /* Get timeout */
      tickstart = HAL_GetTick();
      
      /* SHSR1 can be written when BWST1  equals RESET */
      while (((hdac->Instance->SR) & DAC_SR_BWST1)!= RESET)
      {
        /* Check for the Timeout */
        if((HAL_GetTick() - tickstart) > TIMEOUT_DAC_CALIBCONFIG)
        {
          /* Update error code */
          SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_TIMEOUT);

          /* Change the DMA state */
          hdac->State = HAL_DAC_STATE_TIMEOUT;

          return HAL_TIMEOUT;
        }
      }
      HAL_Delay(1);
      hdac->Instance->SHSR1 = sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime;
    }
    else /* Channel 2 */
    {
      /* SHSR2 can be written when BWST2 equals RESET */

      while (((hdac->Instance->SR) & DAC_SR_BWST2)!= RESET)
      {
        /* Check for the Timeout */
        if((HAL_GetTick() - tickstart) > TIMEOUT_DAC_CALIBCONFIG)
        {
          /* Update error code */
          SET_BIT(hdac->ErrorCode, HAL_DAC_ERROR_TIMEOUT);

          /* Change the DMA state */
          hdac->State = HAL_DAC_STATE_TIMEOUT;

          return HAL_TIMEOUT;
        }
      }
      HAL_Delay(1);
      hdac->Instance->SHSR2 = sConfig->DAC_SampleAndHoldConfig.DAC_SampleTime;
    }
    /* HoldTime */
    hdac->Instance->SHHR = (sConfig->DAC_SampleAndHoldConfig.DAC_HoldTime)<<Channel;
    /* RefreshTime */
    hdac->Instance->SHRR = (sConfig->DAC_SampleAndHoldConfig.DAC_RefreshTime)<<Channel;
  }
    
  if(sConfig->DAC_UserTrimming == DAC_TRIMMING_USER)
  /* USER TRIMMING */
  {
  /* Get the DAC CCR value */
  tmpreg1 = hdac->Instance->CCR;
  /* Clear trimming value */
  tmpreg1 &= ~(((uint32_t)(DAC_CCR_OTRIM1)) << Channel);
  /* Configure for the selected trimming offset */
  tmpreg2 = sConfig->DAC_TrimmingValue;
  /* Calculate CCR register value depending on DAC_Channel */
  tmpreg1 |= tmpreg2 << Channel;
  /* Write to DAC CCR */
  hdac->Instance->CCR = tmpreg1;
  }
  /* else factory trimming is used (factory setting are available at reset)*/
  /* SW Nothing has nothing to do */
  
  /* Get the DAC MCR value */
  tmpreg1 = hdac->Instance->MCR;
  /* Clear DAC_MCR_MODE2_0, DAC_MCR_MODE2_1 and DAC_MCR_MODE2_2 bits */
  tmpreg1 &= ~(((uint32_t)(DAC_MCR_MODE1)) << Channel); 
  /* Configure for the selected DAC channel: mode, buffer output & on chip peripheral connect */
  tmpreg2 = (sConfig->DAC_SampleAndHold | sConfig->DAC_OutputBuffer | sConfig->DAC_ConnectOnChipPeripheral);
  /* Calculate MCR register value depending on DAC_Channel */
  tmpreg1 |= tmpreg2 << Channel;
  /* Write to DAC MCR */
  hdac->Instance->MCR = tmpreg1;
  
  /* DAC in normal operating mode hence clear DAC_CR_CENx bit */
  CLEAR_BIT (hdac->Instance->CR, DAC_CR_CEN1 << Channel);
  
  /* Get the DAC CR value */
  tmpreg1 = hdac->Instance->CR;
  /* Clear TENx, TSELx, WAVEx and MAMPx bits */
  tmpreg1 &= ~(((uint32_t)(DAC_CR_MAMP1 | DAC_CR_WAVE1 | DAC_CR_TSEL1 | DAC_CR_TEN1)) << Channel); 
  /* Configure for the selected DAC channel: trigger */
  /* Set TSELx and TENx bits according to DAC_Trigger value */
  tmpreg2 = (sConfig->DAC_Trigger);
  /* Calculate CR register value depending on DAC_Channel */
  tmpreg1 |= tmpreg2 << Channel;
  /* Write to DAC CR */
  hdac->Instance->CR = tmpreg1;
      
  /* Disable wave generation */
  hdac->Instance->CR &= ~(DAC_CR_WAVE1 << Channel);
  
  /* Change DAC state */
  hdac->State = HAL_DAC_STATE_READY;
  
  /* Process unlocked */
  __HAL_UNLOCK(hdac);
  
  /* Return function status */
  return HAL_OK;
}
示例#26
0
/**
  * @brief Receive an amount of data (Control Flow) with Interrupt
  * @param hspdif: SPDIFRX handle
  * @param pData: a 32-bit pointer to the Receive data buffer.
  * @param Size: number of data sample (Control Flow) to be received :
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SPDIFRX_ReceiveControlFlow_IT(SPDIFRX_HandleTypeDef *hspdif, uint32_t *pData, uint16_t Size)
{
  uint32_t tickstart = 0U;

  if((hspdif->State == HAL_SPDIFRX_STATE_READY) || (hspdif->State == HAL_SPDIFRX_STATE_BUSY_RX))
  {
    if((pData == NULL ) || (Size == 0U))
    {
      return HAL_ERROR;
    }

    /* Process Locked */
    __HAL_LOCK(hspdif);

    hspdif->pCsBuffPtr = pData;
    hspdif->CsXferSize = Size;
    hspdif->CsXferCount = Size;

    hspdif->ErrorCode = HAL_SPDIFRX_ERROR_NONE;

    /* Check if a receive process is ongoing or not */
    hspdif->State = HAL_SPDIFRX_STATE_BUSY_CX;


    /* Enable the SPDIFRX PE Error Interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_PERRIE);

    /* Enable the SPDIFRX OVR Error Interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_OVRIE);

    /* Process Unlocked */
    __HAL_UNLOCK(hspdif);

    /* Enable the SPDIFRX CSRNE interrupt */
    __HAL_SPDIFRX_ENABLE_IT(hspdif, SPDIFRX_IT_CSRNE);

    if (((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != SPDIFRX_STATE_SYNC) || ((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != 0x00U))
    {
      /* Start synchronization */
      __HAL_SPDIFRX_SYNC(hspdif);

      /* Get tick */
      tickstart = HAL_GetTick();

      /* Wait until SYNCD flag is set */
      if(SPDIFRX_WaitOnFlagUntilTimeout(hspdif, SPDIFRX_FLAG_SYNCD, RESET, SPDIFRX_TIMEOUT_VALUE, tickstart) != HAL_OK)
      {
        return HAL_TIMEOUT;
      }

      /* Start reception */
      __HAL_SPDIFRX_RCV(hspdif);
    }

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
示例#27
0
/**
  * @brief  Deactivate an endpoint
  * @param  hpcd: PCD handle
  * @param  ep_addr: endpoint address
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_PCD_EP_Close(PCD_HandleTypeDef *hpcd, uint8_t ep_addr)
{  
  PCD_EPTypeDef *ep;
  
  if ((ep_addr & 0x80) == 0x80)
  {
    ep = &hpcd->IN_ep[ep_addr & 0x7F];
  }
  else
  {
    ep = &hpcd->OUT_ep[ep_addr & 0x7F];
  }
  ep->num   = ep_addr & 0x7F;
  
  ep->is_in = (0x80 & ep_addr) != 0;
  
  __HAL_LOCK(hpcd); 

  if (ep->doublebuffer == 0) 
  {
    if (ep->is_in)
    {
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      /* Configure DISABLE status for the Endpoint*/
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_DIS); 
    }
    else
    {
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      /* Configure DISABLE status for the Endpoint*/
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_DIS);
    }
  }
  /*Double Buffer*/
  else
  { 
    if (ep->is_in==0)
    {
      /* Clear the data toggle bits for the endpoint IN/OUT*/
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      
      /* Reset value of the data toggle bits for the endpoint out*/
      PCD_TX_DTOG(hpcd->Instance, ep->num);
      
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_DIS);
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_DIS);
    }
    else
    {
      /* Clear the data toggle bits for the endpoint IN/OUT*/
      PCD_CLEAR_RX_DTOG(hpcd->Instance, ep->num);
      PCD_CLEAR_TX_DTOG(hpcd->Instance, ep->num);
      PCD_RX_DTOG(hpcd->Instance, ep->num);
      /* Configure DISABLE status for the Endpoint*/
      PCD_SET_EP_TX_STATUS(hpcd->Instance, ep->num, USB_EP_TX_DIS);
      PCD_SET_EP_RX_STATUS(hpcd->Instance, ep->num, USB_EP_RX_DIS);
    }
  } 
  
  __HAL_UNLOCK(hpcd);   
  return HAL_OK;
}
示例#28
0
/**
  * @brief Receive an amount of data (Control Flow) with DMA
  * @param hspdif: SPDIFRX handle
  * @param pData: a 32-bit pointer to the Receive data buffer.
  * @param Size: number of data (Control Flow) sample to be received :
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SPDIFRX_ReceiveControlFlow_DMA(SPDIFRX_HandleTypeDef *hspdif, uint32_t *pData, uint16_t Size)
{
  uint32_t tickstart = 0U;

  if((pData == NULL) || (Size == 0U))
  {
    return  HAL_ERROR;
  }

  if((hspdif->State == HAL_SPDIFRX_STATE_READY) || (hspdif->State == HAL_SPDIFRX_STATE_BUSY_RX))
  {
    hspdif->pCsBuffPtr = pData;
    hspdif->CsXferSize = Size;
    hspdif->CsXferCount = Size;

    /* Process Locked */
    __HAL_LOCK(hspdif);

    hspdif->ErrorCode = HAL_SPDIFRX_ERROR_NONE;
    hspdif->State = HAL_SPDIFRX_STATE_BUSY_CX;

    /* Set the SPDIFRX Rx DMA Half transfer complete callback */
    hspdif->hdmaCsRx->XferHalfCpltCallback = SPDIFRX_DMACxHalfCplt;

    /* Set the SPDIFRX Rx DMA transfer complete callback */
    hspdif->hdmaCsRx->XferCpltCallback = SPDIFRX_DMACxCplt;

    /* Set the DMA error callback */
    hspdif->hdmaCsRx->XferErrorCallback = SPDIFRX_DMAError;

    /* Enable the DMA request */
    HAL_DMA_Start_IT(hspdif->hdmaCsRx, (uint32_t)&hspdif->Instance->CSR, (uint32_t)hspdif->pCsBuffPtr, Size);

    /* Enable CBDMAEN bit in SPDIFRX CR register for control flow reception*/
    hspdif->Instance->CR |= SPDIFRX_CR_CBDMAEN;

    if (((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != SPDIFRX_STATE_SYNC) || ((SPDIFRX->CR & SPDIFRX_CR_SPDIFEN) != 0x00U))
    {
      /* Start synchronization */
      __HAL_SPDIFRX_SYNC(hspdif);

      /* Get tick */
      tickstart = HAL_GetTick();

      /* Wait until SYNCD flag is set */
      if(SPDIFRX_WaitOnFlagUntilTimeout(hspdif, SPDIFRX_FLAG_SYNCD, RESET, SPDIFRX_TIMEOUT_VALUE, tickstart) != HAL_OK)
      {
        return HAL_TIMEOUT;
      }

      /* Start reception */
      __HAL_SPDIFRX_RCV(hspdif);
    }

    /* Process Unlocked */
    __HAL_UNLOCK(hspdif);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
示例#29
0
/**
  * @brief  Initiates and transmits a CAN frame message.
  * @param  hcan: pointer to a CAN_HandleTypeDef structure that contains
  *         the configuration information for the specified CAN.  
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef* hcan)
{
  uint32_t  transmitmailbox = 5;
  uint32_t tmp = 0;
  
  /* Check the parameters */
  assert_param(IS_CAN_IDTYPE(hcan->pTxMsg->IDE));
  assert_param(IS_CAN_RTR(hcan->pTxMsg->RTR));
  assert_param(IS_CAN_DLC(hcan->pTxMsg->DLC));
  
  tmp = hcan->State;
  if((tmp == HAL_CAN_STATE_READY) || (tmp == HAL_CAN_STATE_BUSY_RX))
  {
    /* Process Locked */
    __HAL_LOCK(hcan);
    
    /* Select one empty transmit mailbox */
    if((hcan->Instance->TSR&CAN_TSR_TME0) == CAN_TSR_TME0)
    {
      transmitmailbox = 0;
    }
    else if((hcan->Instance->TSR&CAN_TSR_TME1) == CAN_TSR_TME1)
    {
      transmitmailbox = 1;
    }
    else if((hcan->Instance->TSR&CAN_TSR_TME2) == CAN_TSR_TME2)
    {
      transmitmailbox = 2;
    }
    else
    {
      transmitmailbox = CAN_TXSTATUS_NOMAILBOX;
    }

    if(transmitmailbox != CAN_TXSTATUS_NOMAILBOX)
    {
      /* Set up the Id */
      hcan->Instance->sTxMailBox[transmitmailbox].TIR &= CAN_TI0R_TXRQ;
      if(hcan->pTxMsg->IDE == CAN_ID_STD)
      {
        assert_param(IS_CAN_STDID(hcan->pTxMsg->StdId));  
        hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->StdId << 21) | \
                                                  hcan->pTxMsg->RTR);
      }
      else
      {
        assert_param(IS_CAN_EXTID(hcan->pTxMsg->ExtId));
        hcan->Instance->sTxMailBox[transmitmailbox].TIR |= ((hcan->pTxMsg->ExtId << 3) | \
                                                  hcan->pTxMsg->IDE | \
                                                  hcan->pTxMsg->RTR);
      }
    
      /* Set up the DLC */
      hcan->pTxMsg->DLC &= (uint8_t)0x0000000F;
      hcan->Instance->sTxMailBox[transmitmailbox].TDTR &= (uint32_t)0xFFFFFFF0;
      hcan->Instance->sTxMailBox[transmitmailbox].TDTR |= hcan->pTxMsg->DLC;

      /* Set up the data field */
      hcan->Instance->sTxMailBox[transmitmailbox].TDLR = (((uint32_t)hcan->pTxMsg->Data[3] << 24) | 
                                             ((uint32_t)hcan->pTxMsg->Data[2] << 16) |
                                             ((uint32_t)hcan->pTxMsg->Data[1] << 8) | 
                                             ((uint32_t)hcan->pTxMsg->Data[0]));
      hcan->Instance->sTxMailBox[transmitmailbox].TDHR = (((uint32_t)hcan->pTxMsg->Data[7] << 24) | 
                                             ((uint32_t)hcan->pTxMsg->Data[6] << 16) |
                                             ((uint32_t)hcan->pTxMsg->Data[5] << 8) |
                                             ((uint32_t)hcan->pTxMsg->Data[4]));
    
      if(hcan->State == HAL_CAN_STATE_BUSY_RX) 
      {
        /* Change CAN state */
        hcan->State = HAL_CAN_STATE_BUSY_TX_RX;
      }
      else
      {
        /* Change CAN state */
        hcan->State = HAL_CAN_STATE_BUSY_TX;
      }
      
      /* Set CAN error code to none */
      hcan->ErrorCode = HAL_CAN_ERROR_NONE;
      
      /* Process Unlocked */
      __HAL_UNLOCK(hcan);
      
      /* Enable Error warning Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EWG);
      
      /* Enable Error passive Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_EPV);
      
      /* Enable Bus-off Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_BOF);
      
      /* Enable Last error code Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_LEC);
      
      /* Enable Error Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_ERR);
      
      /* Enable Transmit mailbox empty Interrupt */
      __HAL_CAN_ENABLE_IT(hcan, CAN_IT_TME);
      
      /* Request transmission */
      hcan->Instance->sTxMailBox[transmitmailbox].TIR |= CAN_TI0R_TXRQ;
    }
  }
  else
  {
    return HAL_BUSY;
  }
  
  return HAL_OK;
}
示例#30
0
/**
  * @brief Send data in blocking mode 
  * @param hcec: CEC handle
  * @param DestinationAddress: destination logical address      
  * @param pData: pointer to input byte data buffer
  * @param Size: amount of data to be sent in bytes (without counting the header).
  *              0 means only the header is sent (ping operation).
  *              Maximum TX size is 15 bytes (1 opcode and up to 14 operands).    
  * @param  Timeout: Timeout duration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_CEC_Transmit(CEC_HandleTypeDef *hcec, uint8_t DestinationAddress, uint8_t *pData, uint32_t Size, uint32_t Timeout)
{
  uint8_t  temp = 0;  
  uint32_t tempisr = 0;   
  uint32_t tickstart = 0;

  if((hcec->State == HAL_CEC_STATE_READY) && (__HAL_CEC_GET_TRANSMISSION_START_FLAG(hcec) == RESET)) 
  {
    hcec->ErrorCode = HAL_CEC_ERROR_NONE;
    if((pData == NULL ) && (Size > 0)) 
    {
      hcec->State = HAL_CEC_STATE_ERROR;
      return  HAL_ERROR;                                    
    }

    assert_param(IS_CEC_ADDRESS(DestinationAddress)); 
    assert_param(IS_CEC_MSGSIZE(Size));
    
    /* Process Locked */
    __HAL_LOCK(hcec);
    
    hcec->State = HAL_CEC_STATE_BUSY_TX;

    hcec->TxXferCount = Size;
    
    /* case no data to be sent, sender is only pinging the system */
    if (Size == 0)
    {
      /* Set TX End of Message (TXEOM) bit, must be set before writing data to TXDR */
      __HAL_CEC_LAST_BYTE_TX_SET(hcec);
    }
    
    /* send header block */
    temp = ((uint32_t)hcec->Init.InitiatorAddress << CEC_INITIATOR_LSB_POS) | DestinationAddress;
    hcec->Instance->TXDR = temp;
    /* Set TX Start of Message  (TXSOM) bit */
    __HAL_CEC_FIRST_BYTE_TX_SET(hcec);
    
    while (hcec->TxXferCount > 0)
    {
      hcec->TxXferCount--;

      tickstart = HAL_GetTick();
      while(HAL_IS_BIT_CLR(hcec->Instance->ISR, CEC_FLAG_TXBR))
      {
      	if(Timeout != HAL_MAX_DELAY)
        {
          if((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout))
          {
            hcec->State = HAL_CEC_STATE_TIMEOUT;                
            /* Process Unlocked */
            __HAL_UNLOCK(hcec);       
            return HAL_TIMEOUT;
          }
        }        

        /* check whether error occurred while waiting for TXBR to be set:
         * has Tx underrun occurred ?
         * has Tx error occurred ?
         * has Tx Missing Acknowledge error occurred ? 
         * has Arbitration Loss error occurred ? */
        tempisr = hcec->Instance->ISR;
        if ((tempisr & (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE|CEC_FLAG_ARBLST)) != 0)
        {
          /* copy ISR for error handling purposes */
          hcec->ErrorCode = tempisr;
         /* clear all error flags by default */
         __HAL_CEC_CLEAR_FLAG(hcec, (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE|CEC_FLAG_ARBLST));
         hcec->State = HAL_CEC_STATE_ERROR;
         __HAL_UNLOCK(hcec);
         return  HAL_ERROR;                                    
        }
      } 
      /* TXBR to clear BEFORE writing TXDR register */
      __HAL_CEC_CLEAR_FLAG(hcec, CEC_FLAG_TXBR);
      if (hcec->TxXferCount == 0)
      {
        /* if last byte transmission, set TX End of Message (TXEOM) bit */
        __HAL_CEC_LAST_BYTE_TX_SET(hcec);
      }
      hcec->Instance->TXDR = *pData++;
      
      /* error check after TX byte write up */
      tempisr = hcec->Instance->ISR;
      if ((tempisr & (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE|CEC_FLAG_ARBLST)) != 0)
      {
        /* copy ISR for error handling purposes */
        hcec->ErrorCode = tempisr;
        /* clear all error flags by default */
        __HAL_CEC_CLEAR_FLAG(hcec, (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE|CEC_FLAG_ARBLST));
        hcec->State = HAL_CEC_STATE_ERROR;
        __HAL_UNLOCK(hcec);
        return  HAL_ERROR;                                    
      }
    } /* end while (while (hcec->TxXferCount > 0)) */
    
   
    /* if no error up to this point, check that transmission is  
     * complete, that is wait until TXEOM is reset */
    tickstart = HAL_GetTick();

    while (HAL_IS_BIT_SET(hcec->Instance->CR, CEC_CR_TXEOM))
    {
    	if(Timeout != HAL_MAX_DELAY)
      {
        if((Timeout == 0) || ((HAL_GetTick() - tickstart) > Timeout))
        {
          hcec->State = HAL_CEC_STATE_ERROR;
          __HAL_UNLOCK(hcec);             
          return HAL_TIMEOUT;
        }
      } 
    }

    /* Final error check once all bytes have been transmitted */
    tempisr = hcec->Instance->ISR;
    if ((tempisr & (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE)) != 0)
    {
      /* copy ISR for error handling purposes */
      hcec->ErrorCode = tempisr;
      /* clear all error flags by default */
      __HAL_CEC_CLEAR_FLAG(hcec, (CEC_FLAG_TXUDR|CEC_FLAG_TXERR|CEC_FLAG_TXACKE));
      hcec->State = HAL_CEC_STATE_ERROR;
      __HAL_UNLOCK(hcec);
      return  HAL_ERROR;                                    
    } 

    hcec->State = HAL_CEC_STATE_READY;
    __HAL_UNLOCK(hcec);
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;   
  }
}