void adc_init()
{
GPIO_InitTypeDef GPIO_InitStructure;
ADC_InitTypeDef ADC_InitStructure;
RCC_HSICmd(ENABLE);
while (RCC_GetFlagStatus(RCC_FLAG_HSIRDY) == RESET);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA , ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_2 | GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5; //2, 3
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOA, &GPIO_InitStructure);
ADC_InitStructure.ADC_ScanConvMode = ENABLE; //We will convert single channel only
ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;//we will convert many times
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; //right 12-bit data alignment in ADC data register
ADC_Init(ADC1, &ADC_InitStructure);//load structure values to control and status registers
ADC_InjectedSequencerLengthConfig(ADC1, 4);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_2, 1, ADC_SampleTime_192Cycles);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_3, 2, ADC_SampleTime_192Cycles);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_4, 3, ADC_SampleTime_192Cycles);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_5, 4, ADC_SampleTime_192Cycles);
ADC_ExternalTrigInjectedConvEdgeConfig(ADC1, ADC_ExternalTrigInjecConvEdge_None);
ADC_AutoInjectedConvCmd(ADC1, ENABLE);
ADC_Cmd(ADC1, ENABLE);
while(!(ADC1->SR&ADC_SR_ADONS)); //wait till ready
//TODO: delay();
ADC_SoftwareStartInjectedConv(ADC1);
//TODO: delay();
}
/***********************************************************
* 函数声明：ADC初始化函数 *
* function：采集片内温度，保温盒温度，三相电有效值 *
* 输出 ： 无 *
* 调用函数：ST F.W. Ver3.0 *
***********************************************************/
void ADC1_Configuration(void)
{
ADC_InitTypeDef ADC_InitStructure;
/* 12MHz的时钟 */
RCC_ADCCLKConfig(RCC_PCLK2_Div6); /* David */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1,ENABLE);
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode = ENABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_NbrOfChannel = 1;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_Init(ADC1, &ADC_InitStructure);
/*
ADC1, ADC_Channel_0->PA0->恒温盒内温度
ADC_SampleTime_71Cycles5
*/
ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_239Cycles5); //恒温盒内温度
#if 1
ADC_InjectedSequencerLengthConfig(ADC1, 1);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_16, 1, ADC_SampleTime_239Cycles5);//ADC_SampleTime_55Cycles5
ADC_TempSensorVrefintCmd(ENABLE); //测温度的 使能
ADC_ExternalTrigInjectedConvConfig(ADC1, ADC_ExternalTrigInjecConv_None); // ADC_ExternalTrigInjecConv_T2_TRGO
ADC_AutoInjectedConvCmd(ADC1, ENABLE);
#endif
ADC_DMACmd(ADC1, ENABLE);
ADC_Cmd(ADC1, ENABLE);
ADC_ResetCalibration(ADC1);
while(ADC_GetResetCalibrationStatus(ADC1));
ADC_StartCalibration(ADC1);
while(ADC_GetCalibrationStatus(ADC1));
ADC_SoftwareStartConvCmd(ADC1, ENABLE);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* System clocks configuration ---------------------------------------------*/
RCC_Configuration();
/* NVIC configuration ------------------------------------------------------*/
NVIC_Configuration();
/* GPIO configuration ------------------------------------------------------*/
GPIO_Configuration();
/* TIM1 configuration ------------------------------------------------------*/
/* Time Base configuration */
TIM_TimeBaseStructInit(&TIM_TimeBaseStructure);
TIM_TimeBaseStructure.TIM_Period = 0xFF;
TIM_TimeBaseStructure.TIM_Prescaler = 0x4;
TIM_TimeBaseStructure.TIM_ClockDivision = 0x0;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure);
/* TIM1 channel1 configuration in PWM mode */
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_Pulse = 0x7F;
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;
TIM_OC1Init(TIM1, &TIM_OCInitStructure);
/* DMA1 Channel1 Configuration ----------------------------------------------*/
DMA_DeInit(DMA1_Channel1);
DMA_InitStructure.DMA_PeripheralBaseAddr = ADC1_DR_Address;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)ADC_RegularConvertedValueTab;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_BufferSize = 32;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
DMA_Init(DMA1_Channel1, &DMA_InitStructure);
/* Enable DMA1 channel1 */
DMA_Cmd(DMA1_Channel1, ENABLE);
/* ADC1 configuration ------------------------------------------------------*/
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode = DISABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfChannel = 1;
ADC_Init(ADC1, &ADC_InitStructure);
/* ADC1 regular channel14 configuration */
ADC_RegularChannelConfig(ADC1, ADC_Channel_14, 1, ADC_SampleTime_13Cycles5);
/* Set injected sequencer length */
ADC_InjectedSequencerLengthConfig(ADC1, 1);
/* ADC1 injected channel Configuration */
ADC_InjectedChannelConfig(ADC1, ADC_Channel_11, 1, ADC_SampleTime_71Cycles5);
/* ADC1 injected external trigger configuration */
ADC_ExternalTrigInjectedConvConfig(ADC1, ADC_ExternalTrigInjecConv_None);
/* Enable automatic injected conversion start after regular one */
ADC_AutoInjectedConvCmd(ADC1, ENABLE);
/* Enable ADC1 DMA */
ADC_DMACmd(ADC1, ENABLE);
/* Enable ADC1 external trigger */
ADC_ExternalTrigConvCmd(ADC1, ENABLE);
/* Enable JEOC interrupt */
ADC_ITConfig(ADC1, ADC_IT_JEOC, ENABLE);
/* Enable ADC1 */
ADC_Cmd(ADC1, ENABLE);
/* Enable ADC1 reset calibration register */
ADC_ResetCalibration(ADC1);
/* Check the end of ADC1 reset calibration register */
while(ADC_GetResetCalibrationStatus(ADC1));
/* Start ADC1 calibration */
ADC_StartCalibration(ADC1);
/* Check the end of ADC1 calibration */
while(ADC_GetCalibrationStatus(ADC1));
/* TIM1 counter enable */
TIM_Cmd(TIM1, ENABLE);
/* TIM1 main Output Enable */
TIM_CtrlPWMOutputs(TIM1, ENABLE);
/* Test on channel1 transfer complete flag */
while(!DMA_GetFlagStatus(DMA1_FLAG_TC1));
/* Clear channel1 transfer complete flag */
DMA_ClearFlag(DMA1_FLAG_TC1);
/* TIM1 counter disable */
TIM_Cmd(TIM1, DISABLE);
while (1)
{
}
}
void o2pt_adc_init(void)
{
/*
PC0 VFB_A ADC123_IN10
PC1 VFB_B ADC123_IN11
PC2 IFB_A ADC123_IN12
PC3 IFB_B ADC123_IN13
PC4 VO2S_A ADC12_IN14
PC5 VO2S_B ADC12_IN15
*/
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
//ADC
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
GPIO_InitStructure.GPIO_Pin = \
GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | \
GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5;
GPIO_Init(GPIOC, &GPIO_InitStructure);
ADC_InitTypeDef ADC_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);
RCC_ADCCLKConfig(RCC_PCLK2_Div6); /*72Mhz/6 = 12Mhz, note: 14MHz at most*/
ADC_DeInit(ADC1);
ADC_DeInit(ADC2);
ADC_StructInit(&ADC_InitStructure);
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode = ENABLE;
ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfChannel = 0;
ADC_Init(ADC1, &ADC_InitStructure);
ADC_Init(ADC2, &ADC_InitStructure);
ADC_InjectedSequencerLengthConfig(ADC1, 4); //!!!length must be configured at first
ADC_InjectedChannelConfig(ADC1, ADC_Channel_10, 1, ADC_SampleTime_239Cycles5); //12Mhz / (12.5 + 239.5) = 47Khz
ADC_InjectedChannelConfig(ADC1, ADC_Channel_11, 2, ADC_SampleTime_239Cycles5);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_12, 3, ADC_SampleTime_239Cycles5);
ADC_InjectedChannelConfig(ADC1, ADC_Channel_13, 4, ADC_SampleTime_239Cycles5);
ADC_ExternalTrigInjectedConvConfig(ADC1, ADC_ExternalTrigInjecConv_None);
ADC_AutoInjectedConvCmd(ADC1, ENABLE); //!!!must be set because inject channel do not support CONT mode independently
ADC_InjectedSequencerLengthConfig(ADC2, 2); //!!!length must be configured at first
ADC_InjectedChannelConfig(ADC2, ADC_Channel_14, 1, ADC_SampleTime_239Cycles5); //12Mhz / (12.5 + 239.5) = 47Khz
ADC_InjectedChannelConfig(ADC2, ADC_Channel_15, 2, ADC_SampleTime_239Cycles5);
ADC_ExternalTrigInjectedConvConfig(ADC2, ADC_ExternalTrigInjecConv_None);
ADC_AutoInjectedConvCmd(ADC2, ENABLE); //!!!must be set because inject channel do not support CONT mode independently
ADC_Cmd(ADC1, ENABLE);
ADC_ResetCalibration(ADC1);
while(ADC_GetResetCalibrationStatus(ADC1));
ADC_StartCalibration(ADC1);
while(ADC_GetCalibrationStatus(ADC1)); //WARNNING: DEAD LOOP!!!
ADC_SoftwareStartConvCmd(ADC1, ENABLE);
ADC_Cmd(ADC2, ENABLE);
ADC_ResetCalibration(ADC2);
while(ADC_GetResetCalibrationStatus(ADC2));
ADC_StartCalibration(ADC2);
while(ADC_GetCalibrationStatus(ADC2)); //WARNNING: DEAD LOOP!!!
ADC_SoftwareStartConvCmd(ADC2, ENABLE);
}
