uint32_t PWMSetPeriod(uint8_t channel, uint32_t period) {
if (channel > CHANNEL_C_TIMER_INDEX) {
return 1;
}
if (eDVSMode != EDVS_MODE_INTERNAL && channel == 0) {
return 1; // channel 0 taken for master/slave mode
}
LPC_TIMER_T * timer = halTimers[channel].timer;
halTimers[channel].period = period;
/**
* If the period equal 0, the timer is disable and its outputs are set as GPIO and driven low.
*/
if (period == 0) {
Chip_TIMER_DeInit(timer); //Stop the timer
Chip_TIMER_SetMatch(timer, 2, 0);
halTimers[channel].enabled[0] = DISABLE;
halTimers[channel].enabled[1] = DISABLE;
Chip_GPIO_SetPinDIRInput(LPC_GPIO_PORT, halTimers[channel].portGpio[0], halTimers[channel].pinGpio[0]);
Chip_GPIO_SetPinDIRInput(LPC_GPIO_PORT, halTimers[channel].portGpio[1], halTimers[channel].pinGpio[1]);
Chip_GPIO_SetPinOutLow(LPC_GPIO_PORT, halTimers[channel].portGpio[0], halTimers[channel].pinGpio[0]);
Chip_GPIO_SetPinOutLow(LPC_GPIO_PORT, halTimers[channel].portGpio[1], halTimers[channel].pinGpio[1]);
Chip_SCU_PinMuxSet(halTimers[channel].port[0], halTimers[channel].pin[0], halTimers[channel].gpioMode[0]);
Chip_SCU_PinMuxSet(halTimers[channel].port[1], halTimers[channel].pin[1], halTimers[channel].gpioMode[1]);
} else {
/**
* The channel match 2 is used as the controller of the base frequency.
* When there is a match on this channel, the timer is reset and the external match bit
* is set to 1.
* The M0 core is looking for this change and it sets the output of the channels to high.
*/
Chip_TIMER_Init(timer);
Chip_TIMER_Disable(timer);
Chip_TIMER_Reset(timer);
/**
* The Main clock is running at 192Mhz so set the Prescaler in order to have
* a 1 Mhz timer. Timer_CLK = Main_CLK/ (PR+1)
*/
Chip_TIMER_PrescaleSet(timer, 191);
Chip_TIMER_ResetOnMatchEnable(timer, 2);
Chip_TIMER_StopOnMatchDisable(timer, 2);
Chip_TIMER_MatchDisableInt(timer, 2);
Chip_TIMER_SetMatch(timer, 2, period);
//Reconfigure match channels!
if (halTimers[channel].enabled[0]) {
PWMSetWidth(channel, 0, halTimers[channel].witdh[0]);
}
if (halTimers[channel].enabled[1]) {
PWMSetWidth(channel, 1, halTimers[channel].witdh[1]);
}
Chip_TIMER_ExtMatchControlSet(timer, 0, TIMER_EXTMATCH_SET, 2);
// Clear interrupt pending
timer->IR = 0xFFFFFFFF;
Chip_TIMER_Enable(timer);
}
return 0;
}
/*
* @Brief Disables timer peripheral
* @param timerNumber: Timer number, 0 to 3
* @return nothing
*/
void Timer_DeInit(uint8_t timerNumber){
NVIC_DisableIRQ(timer_sd[timerNumber].IRQn);
Chip_TIMER_Disable(timer_sd[timerNumber].name);
Chip_TIMER_DeInit(timer_sd[timerNumber].name);
}