void SetupInterrupts(void)
{
//ConfigIntTimer1(T1_INT_PRIOR_4 & T1_INT_OFF);
//ConfigIntTimer2(T2_INT_PRIOR_4 & T2_INT_OFF);
ConfigIntUART1(UART_TX_INT_EN & UART_TX_INT_PR4 & UART_RX_INT_EN &
UART_RX_INT_PR4); //UART TX/RX
}
// Set up the UART for the GSM chip
void gsmSetup(void)
{
// Configure Port Direction
TRISGbits.TRISG6 = 0; // Turn RG6 into output for GSM TX
TRISGbits.TRISG7 = 1; // Turn RG7 into input for GSM RX
// Configure PPS pins for GSM
iPPSInput(IN_FN_PPS_U1RX,IN_PIN_PPS_RP26); // Assign U1RX to pin RP26
iPPSOutput(OUT_PIN_PPS_RP21,OUT_FN_PPS_U1TX); // Assign U1TX to pin RP21
// Close UART in case it's already open
CloseUART1();
// Enable UART Interface
ConfigIntUART1(UART_RX_INT_DIS | UART_RX_INT_PR7 | UART_TX_INT_DIS | UART_TX_INT_PR7);
// Receive interrupt disabled
// Transmit interrupt disabled
OpenUART1(UART_EN, UART_TX_ENABLE, 25);
// Module enable
// BRG generates 4 clocks per bit period
// Transmit enable
// 9600 baud rate (@ 4 MHz FCY)
}
void initUART1(int pbClk)
{
#define config1 UART_EN | UART_IDLE_CON | UART_RX_TX | UART_DIS_WAKE | UART_DIS_LOOPBACK | UART_DIS_ABAUD | UART_NO_PAR_8BIT | UART_1STOPBIT | UART_IRDA_DIS | UART_DIS_BCLK_CTS_RTS| UART_NORMAL_RX | UART_BRGH_SIXTEEN
#define config2 UART_TX_PIN_LOW | UART_RX_ENABLE | UART_TX_ENABLE | UART_INT_TX | UART_INT_RX_CHAR | UART_ADR_DETECT_DIS | UART_RX_OVERRUN_CLEAR
OpenUART1(config1, config2, pbClk / 16 / DESIRED_BAUDRATE - 1); // calculate actual BAUD generate value.
ConfigIntUART1(UART_INT_PR2 | UART_RX_INT_EN);
INTEnableSystemMultiVectoredInt();
}
void UART1_Config(void){
OpenUART1((
UART_EN & //Enable UART Module
UART_IDLE_CON & //Work while idle
UART_IrDA_DISABLE & //Disable Infared decoder
UART_MODE_SIMPLEX & //UART Simplex mode (RTS pin)
UART_UEN_00 & //TX/RX pins configured all other latched
UART_DIS_WAKE & //Disable wake on Start bit
UART_DIS_LOOPBACK & //Disable loopback
UART_DIS_ABAUD & //Disable Auto Baud
UART_UXRX_IDLE_ONE & //Receive idle is 1
UART_BRGH_SIXTEEN & //16 clocks per bit period
UART_NO_PAR_8BIT & //No parity bit
UART_1STOPBIT //One stop bit
),
(
UART_INT_TX_LAST_CH & //Interrupt when last character shifted out
UART_IrDA_POL_INV_ZERO & //IrDA encoded, UxTX Idel state is '0'
UART_SYNC_BREAK_DISABLED & //Sync break transmission disabled or completed
UART_TX_ENABLE & //Transmit enable
UART_TX_BUF_NOT_FUL & //Transmit buffer is not full
UART_INT_RX_CHAR & //Interrupt on every char received
UART_ADR_DETECT_DIS & //address detect disable
UART_RX_OVERRUN_CLEAR //Rx buffer Over run status bit clear
),
(
__BAUDUART1_ //Baud rate
));
ConfigIntUART1(
UART_RX_INT_DIS & //Receive interrupt enabled
UART_RX_INT_PR1 & //Priority RX interrupt 1
UART_TX_INT_DIS & //transmit interrupt disabled
UART_TX_INT_PR2 //Priority TX interrupt 1
);
#ifdef InvertRxTxBits
U1STAbits.UTXINV = 0;
U1MODEbits.URXINV = 0;
#endif
//Set the tristate and map pins for Uart
TRIS_U1TX;
//TRIS_U1RX;
MAP_U1TX;
//MAP_U1RX;
}
void LS1_UART_Init (void)
{
CPU_INT08U config;
CPU_INT32U config1;
CPU_INT32U config2;
config1 = UART_EN // UART module enabled
| UART_IDLE_CON // UART works in IDLE mode
| UART_RX_TX // Communication is done through the normal pins
| UART_DIS_WAKE // Disable Wake-up on START bit detect during SLEEP
| UART_DIS_LOOPBACK // Disable loop back
| UART_DIS_ABAUD // Input to capture module from ICx pin
| UART_NO_PAR_8BIT // 8 bits no parity
| UART_1STOPBIT // 1 stop bit
| UART_IRDA_DIS // IrDA disabled
| UART_MODE_FLOWCTRL // UART pins in flow control mode
| UART_DIS_BCLK_CTS_RTS // Disable BCLK, CTS, and RTS pins
| UART_NORMAL_RX // UxRX idle stat is '1'
| UART_BRGH_SIXTEEN; // 16x baud clock
config2 = UART_TX_PIN_LOW // IrDA encoded UxTx idle stat is '0'
| UART_RX_ENABLE // Enable UxRx pin
| UART_TX_ENABLE // Enable UxTx pin
// | UART_INT_TX // Interrupt on trasnfer of each character to TSR
| UART_INT_RX_CHAR // Interrupt on every char received
| UART_ADR_DETECT_DIS // Disable 9-bit address detect
| UART_RX_OVERRUN_CLEAR; // Rx buffer overrun status bit clear
OpenUART1(config1, config2, BSP_CLK_FREQ / (16 * UART1_BAUDRATE) - 1); // Configure the settings
config = UART_INT_PR3
| UART_INT_SUB_PR0
| UART_RX_INT_EN;
ConfigIntUART1(config);
}
BOOL
xMBPortSerialInit( BYTE ucPORT, UINT32 ulBaudRate, BYTE ucDataBits, eMBParity eParity )
{
WORD_VAL wClk;
MBRXIF = 0;
MBRXIE = 0;
MBTXIF = 0;
MBTXIE = 0;
//Включим передачу на 485 пока временно для отладки
//pRE = 0;
TRISBbits.TRISB5 = 1;
TRISBbits.TRISB15 = 0;
//TRISAbits.TRISA7 = 0;
// MBBAUDCON = kMBBAUDCON_SETUP;
// (((SYS_FREQ/4L+2L*kBAUDRATE)/kBAUDRATE)/16L)-1)
//wClk.Val = 207;//(SYS_FREQ/4L+2L*kBAUDRATE)/kBAUDRATE/4L - 1L;
// MBBRG = wClk.byte.LB;
// MBBRGH = wClk.byte.HB;
// MBRCSTA = kMBRCSTA_SETUP;
// MBTXSTA = kMBTXSTA_SETUP;
_U1RXR = 56; //RP5 = RX
_RP55R = 1; //RP15 = TX
OpenUART1(UART_EN &
UART_IDLE_STOP &
UART_IrDA_DISABLE &
UART_DIS_WAKE &
UART_UEN_00 &
UART_DIS_ABAUD &
UART_BRGH_FOUR &
UART_UXRX_IDLE_ONE &
UART_NO_PAR_8BIT &
UART_2STOPBITS &
UART_DIS_LOOPBACK,
UART_INT_TX_BUF_EMPTY &
UART_IrDA_POL_INV_ZERO &
UART_SYNC_BREAK_DISABLED &
UART_TX_ENABLE &
UART_INT_RX_CHAR &
UART_ADR_DETECT_DIS, BRG) ;
ConfigIntUART1(UART_RX_INT_EN &
UART_TX_INT_EN &
UART_RX_INT_PR1 &
UART_TX_INT_PR1);
//U1STAbits.UTXINV = 1;
//_UARTEN = 0;
//_URXINV = 0;
_UTXINV = 0;
//_UARTEN = 1;
// MBTXREG = 0x55;
// MBTXREG = 0x55;
//pbClk=SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
/*if (ucPORT == 1){
OpenUART1(UART_EN, // Module is ON
UART_RX_ENABLE | UART_TX_ENABLE, // Enable TX & RX
pbClk/16/ulBaudRate-1); //
ConfigIntUART1(UART_INT_PR2 | UART_RX_INT_EN);
}
else if (ucPORT == 2){
OpenUART2(UART_EN | UART_NO_PAR_8BIT | UART_2STOPBITS, // Module is ON
UART_RX_ENABLE | UART_TX_ENABLE, // Enable TX & RX
pbClk/16/ulBaudRate-1); //
ConfigIntUART2(UART_INT_PR2 | UART_RX_INT_EN);
}*/
// INTCONbits.GIE = 1;
//INTEnableSystemMultiVectoredInt();
return TRUE;
}
UINT16 SetupUART(void)
{
PPSOutput(OUT_FN_PPS_U1TX, OUT_PIN_PPS_RP37);
PPSInput(PPS_U1RX, PPS_RP20);
OpenUART1(UART_EN &
UART_IDLE_CON &
UART_IrDA_DISABLE &
UART_MODE_SIMPLEX &
UART_UEN_00 &
UART_EN_WAKE &
UART_DIS_LOOPBACK &
UART_DIS_ABAUD &
UART_UXRX_IDLE_ONE &
UART_BRGH_SIXTEEN &
UART_NO_PAR_8BIT &
UART_1STOPBIT
,
UART_INT_TX_BUF_EMPTY &
UART_SYNC_BREAK_DISABLED &
UART_TX_ENABLE &
UART_INT_RX_CHAR &
UART_ADR_DETECT_DIS
,
23
//BAUD = 9600
);
U1STAbits.UTXINV = 0; //make TX active low
//U1STAbits.URXISEL = 0x00; //force interrupt on every 8 bits recieved
ConfigIntUART1(UART_RX_INT_EN &
UART_RX_INT_PR4 &
UART_TX_INT_DIS
);
/*This is a copy of UART setup working for TX
OpenUART1(UART_EN &
UART_IDLE_CON &
UART_IrDA_DISABLE &
UART_MODE_SIMPLEX &
UART_UEN_00 &
UART_EN_WAKE &
UART_DIS_LOOPBACK &
UART_DIS_ABAUD &
UART_UXRX_IDLE_ZERO &
UART_BRGH_SIXTEEN &
UART_NO_PAR_8BIT &
UART_1STOPBIT
,
UART_INT_TX_BUF_EMPTY &
UART_SYNC_BREAK_DISABLED &
UART_TX_ENABLE &
UART_INT_RX_BUF_FUL &
UART_ADR_DETECT_DIS
,
23
//BAUD = 9600
);
U1STAbits.UTXINV = 0;
*/
return 0; //return success
}
void initUART1( unsigned long baudrate )
{
/* Holds the value of baud register */
unsigned int baudvalue;
/* Holds the value of uart config reg */
unsigned int U1MODEvalue;
/* Holds the information regarding uart
* Tx and Rx interrupt modes
*/
unsigned int U1STAvalue;
/* Turn off UART1module */
CloseUART1();
/** Clear UART1 Receive Interrupt Flag
* Note: If flag is not cleared, the program will continue to
* think an interrupt has occured and remain within the
* the user defined interrupt routine.
*/
IFS0bits.U1RXIF = 0;
IFS0bits.U1TXIF = 0;
/** Configure UART1 Receive and Transmit Interrupts */
ConfigIntUART1( UART_RX_INT_EN & // Enable UART1 Receive Interrupts
UART_RX_INT_PR3 & // Set UART1 Receive interrupts to priority 3
UART_TX_INT_DIS & // Disable UART1 Transmit interrupts
UART_TX_INT_PR3 ); // Set UART1 Transmit interrupts to priority 3
/* Configure UART1 module to transmit 8 bit data with one stopbit.
*
* Load a value into Baud Rate Generator. Example is for 38400.
* See section 19.3.1 of datasheet.
* baudvalue = (Fcy/(16*BaudRate))-1
* baudvalue = (40M/(16*38400))-1
* baudvalue = 65
*/
/* Slow speed settings */
if(baudrate <= 57600UL)
{
baudvalue = ( unsigned int )( ( FCY / ( 16 * baudrate ) ) - 1 );
U1MODEvalue = UART_EN & // Enable UART1
UART_IDLE_CON & // Work in idle mode
UART_IrDA_DISABLE & // Disable IrDA encoder and decoder
UART_MODE_FLOW & // UART1 pin in flow control mode
UART_UEN_00 & // U1TX and U1RX used, U1TCS, U1RTS, and BCLK controlled by latch for flow control
UART_DIS_WAKE & // Disable wakeup on start
UART_DIS_LOOPBACK & // Disable loopback mode
UART_DIS_ABAUD & // Baudrate me asurment disabled
UART_UXRX_IDLE_ONE & // U1Rx Idle state is 1 (not 0)
UART_BRGH_SIXTEEN & // Baud Rate Generator generates 16 clocks per bit second (16x baudrate)
UART_NO_PAR_8BIT & // Do not use a parity bit
UART_1STOPBIT; // Use 1 stop bit
}
/* High speed settings */
else
{
baudvalue = ( unsigned int )( ( FCY / ( 4 * baudrate ) ) - 1 );
U1MODEvalue = UART_EN &
UART_IDLE_CON &
UART_IrDA_DISABLE &
UART_MODE_FLOW &
UART_UEN_00 &
UART_DIS_WAKE &
UART_DIS_LOOPBACK &
UART_DIS_ABAUD &
UART_UXRX_IDLE_ONE &
UART_BRGH_FOUR & // Baud Rate Generator generates 4 clocks per bit second (4x baudrate) high speed
UART_NO_PAR_8BIT &
UART_1STOPBIT;
}
/* Status register settings */
U1STAvalue = UART_INT_TX & // Interrupt on transfer of every character to Trap Service Routine
UART_TX_ENABLE & // Enable UART1 transmit
UART_IrDA_POL_INV_ZERO & // IrDA encoded, idle state is 0 (not 1)
UART_SYNC_BREAK_DISABLED & // Sync break transmission disabled
UART_INT_RX_CHAR & // Trigger an interrupt on every character received
UART_ADR_DETECT_DIS & // Disable address detection
UART_TX_BUF_FUL & // Transmit buffer is full
UART_RX_OVERRUN_CLEAR; // Rx buffer over run bit clear
/* Open UART1 connection
*
* This function is defined in uart.h the builtin library fuctions
* provided with the compiler. See uart.h or the C30 library users
* guide for more infromation
*/
OpenUART1( U1MODEvalue, U1STAvalue, baudvalue );
__delay_ms(10);
/* Prints a welcome banner alerting user serial communication port
* has been opened.
*/
//putsUART1("UART1 started!\r\n");
}