static void str7_IrqInit()
{
//设置外部中断
EIC_IRQConfig(ENABLE);
XTI_Init();
XTI_ModeConfig(XTI_Interrupt, ENABLE );
EIC->SIR[XTI_IRQChannel] = ((int)XTI_IRQHandler << 16) | 8;
EIC_IRQChannelConfig(XTI_IRQChannel, ENABLE);
}
/* ----------------------- Start implementation -----------------------------*/
int
main( void )
{
EIC_Init( );
EIC_IRQConfig( ENABLE );
( void )xTaskCreate( vInitTask, NULL, configMINIMAL_STACK_SIZE, NULL,
tskIDLE_PRIORITY, NULL );
vTaskStartScheduler( );
return 0;
}
static void prvSetupTimerInterrupt( void )
{
/* Set the watchdog up to generate a periodic tick. */
WDG_ECITConfig( DISABLE );
WDG_CntOnOffConfig( DISABLE );
WDG_PeriodValueConfig( portMICROS_PER_SECOND / configTICK_RATE_HZ );
/* Setup the tick interrupt in the EIC. */
EIC_IRQChannelPriorityConfig( WDG_IRQChannel, 1 );
EIC_IRQChannelConfig( WDG_IRQChannel, ENABLE );
EIC_IRQConfig( ENABLE );
WDG_ECITConfig( ENABLE );
/* Start the timer - interrupts are actually disabled at this point so
it is safe to do this here. */
WDG_CntOnOffConfig( ENABLE );
}
/*
* See the serial2.h header file.
*/
xComPortHandle xSerialPortInitMinimal( unsigned long ulWantedBaud, unsigned portBASE_TYPE uxQueueLength )
{
xComPortHandle xReturn;
/* Create the queues used to hold Rx and Tx characters. */
xRxedChars = xQueueCreate( uxQueueLength, ( unsigned portBASE_TYPE ) sizeof( signed char ) );
xCharsForTx = xQueueCreate( uxQueueLength + 1, ( unsigned portBASE_TYPE ) sizeof( signed char ) );
/* If the queues were created correctly then setup the serial port
hardware. */
if( ( xRxedChars != serINVALID_QUEUE ) && ( xCharsForTx != serINVALID_QUEUE ) )
{
portENTER_CRITICAL();
{
/* Setup the UART port pins. */
GPIO_Config( GPIO0, UART0_Tx_Pin, GPIO_AF_PP );
GPIO_Config( GPIO0, UART0_Rx_Pin, GPIO_IN_TRI_CMOS );
/* Configure the UART. */
UART_OnOffConfig( UART0, ENABLE );
UART_FifoConfig( UART0, DISABLE );
UART_FifoReset( UART0, UART_RxFIFO );
UART_FifoReset( UART0, UART_TxFIFO );
UART_LoopBackConfig(UART0, DISABLE );
UART_Config( UART0, ulWantedBaud, UART_NO_PARITY, UART_1_StopBits, UARTM_8D );
UART_RxConfig( UART0, ENABLE );
/* Configure the IEC for the UART interrupts. */
EIC_IRQChannelPriorityConfig( UART0_IRQChannel, 1 );
EIC_IRQChannelConfig( UART0_IRQChannel, ENABLE );
EIC_IRQConfig( ENABLE );
UART_ItConfig( UART0, UART_RxBufFull, ENABLE );
}
portEXIT_CRITICAL();
}
else
{
xReturn = ( xComPortHandle ) 0;
}
/* This demo file only supports a single port but we have to return
something to comply with the standard demo header file. */
return xReturn;
}