/*************************************************************
Function: void RS232SendMsg(void)
Description: RS232发送数据函数，用于启动发送
Calls: GPDMA_Setup
GPDMA_ChannelCmd
Called By:
Input: RS232Tx.Buff
RS232Tx.Len
Output: 无
Return: 无
Others: 无
*************************************************************/
void RS232SendMsg ( void )
{
GPDMACfgTx.ChannelNum = 0;
// Source memory
GPDMACfgTx.SrcMemAddr = ( uint32_t ) &RS232Tx.Buff;
// Transfer size
GPDMACfgTx.TransferSize = RS232Tx.Len;
// Destination connection
GPDMACfgTx.DstConn = RS232_TX_PIN;
GPDMA_Setup ( &GPDMACfgTx );
// Enable GPDMA channel 0
GPDMA_ChannelCmd ( 0, ENABLE );
}
/*************************************************************
Function: void RS485Ch2SendMsg(void)
Description: RS485发送数据函数，用于启动发送
Calls: GPDMA_Setup
GPDMA_ChannelCmd
Called By:
Input: RS485Tx2.Buff
RS485Tx2.Len
Output: 无
Return: 无
Others: 无
*************************************************************/
void RS485Ch2SendMsg ( void )
{
GPDMACfgTx.ChannelNum = 2;
// Source memory
GPDMACfgTx.SrcMemAddr = ( uint32_t ) &RS485Tx2.Buff;
// Transfer size
GPDMACfgTx.TransferSize = RS485Tx2.Len;
// Destination connection
GPDMACfgTx.DstConn = GPDMA_CONN_UART2_Tx;
GPDMA_Setup ( &GPDMACfgTx );
// Enable GPDMA channel 0
GPDMA_ChannelCmd ( 2, ENABLE );
RS485Tx2.Flag = 1;
}
/*********************************************************************//**
* @brief Main GPDMA program body
**********************************************************************/
int c_entry(void)
{
GPDMA_Channel_CFG_Type GPDMACfg;
// DeInit NVIC and SCBNVIC
NVIC_DeInit();
NVIC_SCBDeInit();
/* Configure the NVIC Preemption Priority Bits:
* two (2) bits of preemption priority, six (6) bits of sub-priority.
* Since the Number of Bits used for Priority Levels is five (5), so the
* actual bit number of sub-priority is three (3)
*/
NVIC_SetPriorityGrouping(0x05);
// Set Vector table offset value
#if (__RAM_MODE__==1)
NVIC_SetVTOR(0x10000000);
#else
NVIC_SetVTOR(0x00000000);
#endif
/*
* Initialize debug via UART
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/* GPDMA block section -------------------------------------------- */
/* Initialize buffer */
_DBG_("Initialize Buffer...");
Buffer_Init();
/* Disable GPDMA interrupt */
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = DMA_SRC;
// Destination memory
GPDMACfg.DstMemAddr = DMA_DST;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width
GPDMACfg.TransferWidth = GPDMA_WIDTH_WORD;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2M;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg, GPDMA_Callback);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
_DBG_("Start transfer...");
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
/* Wait for GPDMA processing complete */
while ((Channel0_TC == 0) && (Channel0_Err == 0));
/* Verify buffer */
Buffer_Verify();
_DBG(compl_menu);
/* Loop forever */
while(1);
return 1;
}
/*********************************************************************//**
* @brief Main SSP program body
**********************************************************************/
int c_entry(void)
{
GPDMA_Channel_CFG_Type GPDMACfg;
PINSEL_CFG_Type PinCfg;
// DeInit NVIC and SCBNVIC
NVIC_DeInit();
NVIC_SCBDeInit();
/* Configure the NVIC Preemption Priority Bits:
* two (2) bits of preemption priority, six (6) bits of sub-priority.
* Since the Number of Bits used for Priority Levels is five (5), so the
* actual bit number of sub-priority is three (3)
*/
NVIC_SetPriorityGrouping(0x05);
// Set Vector table offset value
#if (__RAM_MODE__==1)
NVIC_SetVTOR(0x10000000);
#else
NVIC_SetVTOR(0x00000000);
#endif
/*
* Initialize SPI pin connect
* P0.15 - SCK;
* P0.16 - SSEL
* P0.17 - MISO
* P0.18 - MOSI
*/
PinCfg.Funcnum = 2;
PinCfg.OpenDrain = 0;
PinCfg.Pinmode = 0;
PinCfg.Portnum = 0;
PinCfg.Pinnum = 15;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 17;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 18;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 16;
PINSEL_ConfigPin(&PinCfg);
/*
* Initialize debug via UART
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/* Initializing SSP device section ------------------------------------------------------ */
// initialize SSP configuration structure to default
SSP_ConfigStructInit(&SSP_ConfigStruct);
// Initialize SSP peripheral with parameter given in structure above
SSP_Init(LPC_SSP0, &SSP_ConfigStruct);
// Enable SSP peripheral
SSP_Cmd(LPC_SSP0, ENABLE);
/* GPDMA Interrupt configuration section ------------------------------------------------- */
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Enable SSP0 interrupt */
NVIC_EnableIRQ(DMA_IRQn);
/* Initializing Buffer section ----------------------------------------------------------- */
Buffer_Init();
/* Initialize GPDMA controller */
GPDMA_Init();
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ (DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Configure GPDMA channel 0 -------------------------------------------------------------*/
/* DMA Channel 0 */
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = (uint32_t) &dma_src;
// Destination memory - Not used
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = sizeof(dma_src);
// Transfer width - not used
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection
GPDMACfg.DstConn = GPDMA_CONN_SSP0_Tx;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg, GPDMA_Callback0);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/* Configure GPDMA channel 1 -------------------------------------------------------------*/
/* DMA Channel 1 */
GPDMACfg.ChannelNum = 1;
// Source memory - not used
GPDMACfg.SrcMemAddr = 0;
// Destination memory - Not used
GPDMACfg.DstMemAddr = (uint32_t) &dma_dst;
// Transfer size
GPDMACfg.TransferSize = sizeof(dma_dst);
// Transfer width - not used
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_SSP0_Rx;
// Destination connection - not used
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg, GPDMA_Callback1);
/* Reset terminal counter */
Channel1_TC = 0;
/* Reset Error counter */
Channel1_Err = 0;
_DBG_("Start transfer...");
// Enable Tx and Rx DMA on SSP0
SSP_DMACmd (LPC_SSP0, SSP_DMA_RX, ENABLE);
SSP_DMACmd (LPC_SSP0, SSP_DMA_TX, ENABLE);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(1, ENABLE);
// Enable interrupt for DMA
NVIC_EnableIRQ (DMA_IRQn);
/* Wait for GPDMA processing complete */
while (((Channel0_TC == 0) && (Channel0_Err == 0)) \
|| ((Channel1_TC == 0) && (Channel1_Err ==0)));
/* Verify buffer */
Buffer_Verify();
_DBG_("Verify complete!");
/* Loop forever */
while(1);
return 1;
}
/*************************************************************
Function: void UartInit(uint8_t num,uint32_t baudrate,uint8_t parity)
Description: 串口初始化函数用于初始化RS232及RS485 将UART配置为中断接收，DMA发送，RS485自动切换方向
Calls:
Called By: main()
Input: num 串口号0、1、2
baudrate 波特率
parity 校验方式
Output: 无
Return: 无
Others: 无
*************************************************************/
void UartInit ( uint8_t num, uint32_t baudrate, uint8_t parity )
{
// uint32_t idx;
// RS485 configuration
UART1_RS485_CTRLCFG_Type rs485cfg;
// UART Configuration structure variable
UART_CFG_Type UARTConfigStruct;
// UART FIFO configuration Struct variable
UART_FIFO_CFG_Type UARTFIFOConfigStruct;
GPDMA_Channel_CFG_Type GPDMACfg;
UART_ConfigStructInit ( &UARTConfigStruct );
UARTConfigStruct.Baud_rate = baudrate;
UARTConfigStruct.Parity = parity;
UART_FIFOConfigStructInit ( &UARTFIFOConfigStruct );
// Enable DMA mode in UART
UARTFIFOConfigStruct.FIFO_DMAMode = ENABLE;
// Destination memory - don't care
GPDMACfgTx.DstMemAddr = 0;
// Transfer width - don't care
GPDMACfgTx.TransferWidth = 0;
// Transfer type
GPDMACfgTx.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - don't care
GPDMACfgTx.SrcConn = 0;
// Linker List Item - unused
GPDMACfgTx.DMALLI = 0;
rs485cfg.AutoDirCtrl_State = ENABLE;
rs485cfg.DirCtrlPol_Level = SET;
rs485cfg.DelayValue = 50;
rs485cfg.NormalMultiDropMode_State = ENABLE;
rs485cfg.AutoAddrDetect_State = DISABLE;
rs485cfg.Rx_State = ENABLE;
if ( num == 0 )
{
//PINSEL_ConfigPin(0,2,1); //UART0
//PINSEL_ConfigPin(0,3,1); //UART0
PINSEL_ConfigPin ( 0, 25, 0x03 );
PINSEL_ConfigPin ( 0, 26, 0xb3 );
// Initalize UART0 peripheral with given to corresponding parameter
UART_Init ( RS232_UART, &UARTConfigStruct );
// Initialize FIFO for UART0 peripheral
UART_FIFOConfig ( RS232_UART, &UARTFIFOConfigStruct );
// Enable UART Transmit
UART_TxCmd ( RS232_UART, ENABLE );
// channel 0
GPDMACfgTx.ChannelNum = 0;
// Source memory
GPDMACfgTx.SrcMemAddr = ( uint32_t ) &RS232Tx.Buff;
// Transfer size
GPDMACfgTx.TransferSize = sizeof ( RS232Tx.Buff );
// Destination connection
GPDMACfgTx.DstConn = RS232_TX_PIN;
RS232Tx.Flag = 0;
RS232_Err = 0;
UART_IntConfig ( RS232_UART, UART_INTCFG_RBR, ENABLE );
UART_IntConfig ( RS232_UART, UART_INTCFG_RLS, ENABLE );
NVIC_SetPriority ( RS232_IRQN, ( ( 0x01 << 3 ) | 0x01 ) );
NVIC_EnableIRQ ( RS232_IRQN );
RS232Rx.Flag = 0 ;
RS232Rx.Len = 0 ;
RS232Rx.Idx = 0 ;
}
if ( num == 1 )
{
PINSEL_ConfigPin ( 2, 0, 2 );
PINSEL_ConfigPin ( 2, 1, 2 );
PINSEL_ConfigPin ( 2, 5, 2 ); //U1_DTR
rs485cfg.DirCtrlPin = UART1_RS485_DIRCTRL_DTR;
UART_Init ( ( LPC_UART_TypeDef * ) LPC_UART1, &UARTConfigStruct );
UART_FIFOConfig ( ( LPC_UART_TypeDef * ) LPC_UART1, &UARTFIFOConfigStruct );
UART_RS485Config ( ( LPC_UART_TypeDef * ) LPC_UART1, &rs485cfg );
// Enable UART Transmit
UART_TxCmd ( ( LPC_UART_TypeDef * ) LPC_UART1, ENABLE );
GPDMACfgTx.ChannelNum = 1;
// Source memory
GPDMACfgTx.SrcMemAddr = ( uint32_t ) &RS485Tx1.Buff;
// Transfer size
GPDMACfgTx.TransferSize = sizeof ( RS485Tx1.Buff );
// Destination connection
GPDMACfgTx.DstConn = GPDMA_CONN_UART1_Tx;
/* Reset terminal counter */
RS485Tx1.Flag = 0;
/* Reset Error counter */
RS4851_Err = 0;
/* Enable UART Rx interrupt */
UART_IntConfig ( ( LPC_UART_TypeDef * ) LPC_UART1, UART_INTCFG_RBR, ENABLE );
/* Enable UART line status interrupt */
UART_IntConfig ( ( LPC_UART_TypeDef * ) LPC_UART1, UART_INTCFG_RLS, ENABLE );
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority ( UART1_IRQn, ( ( 0x01 << 3 ) | 0x01 ) );
/* Enable Interrupt for UART0 channel */
NVIC_EnableIRQ ( UART1_IRQn );
}
if ( num == 2 )
{
PINSEL_ConfigPin ( 2, 8, 2 );
PINSEL_ConfigPin ( 2, 9, 2 );
PINSEL_ConfigPin ( 2, 6, 4 ); //U2_OE
UART_Init ( LPC_UART2, &UARTConfigStruct );
UART_FIFOConfig ( LPC_UART2, &UARTFIFOConfigStruct );
UART_RS485Config ( ( LPC_UART_TypeDef * ) LPC_UART2, &rs485cfg );
// Enable UART Transmit
UART_TxCmd ( LPC_UART2, ENABLE );
GPDMACfgTx.ChannelNum = 2;
// Source memory
GPDMACfgTx.SrcMemAddr = ( uint32_t ) &RS485Tx2.Buff;
// Transfer size
GPDMACfgTx.TransferSize = sizeof ( RS485Tx2.Buff );
// Destination connection
GPDMACfgTx.DstConn = GPDMA_CONN_UART2_Tx;
/* Reset terminal counter */
RS485Tx2.Flag = 0;
/* Reset Error counter */
RS4852_Err = 0;
/* Enable UART Rx interrupt */
UART_IntConfig ( LPC_UART2, UART_INTCFG_RBR, ENABLE );
/* Enable UART line status interrupt */
UART_IntConfig ( LPC_UART2, UART_INTCFG_RLS, ENABLE );
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority ( UART2_IRQn, ( ( 0x01 << 3 ) | 0x01 ) );
/* Enable Interrupt for UART0 channel */
NVIC_EnableIRQ ( UART2_IRQn );
}
/* Initialize GPDMA controller */
GPDMA_Init();
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ ( DMA_IRQn );
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority ( DMA_IRQn, ( ( 0x01 << 3 ) | 0x01 ) );
// Setup channel with given parameter
GPDMA_Setup ( &GPDMACfgTx );
// Enable interrupt for DMA
NVIC_EnableIRQ ( DMA_IRQn );
// Enable GPDMA channel 0
//GPDMA_ChannelCmd(0, ENABLE);
CRC_Init ( CRC_POLY_CRC16 );
}
/*********************************************************************//**
* @brief c_entry: Main DAC program body
* @param[in] None
* @return int
**********************************************************************/
int c_entry(void)
{
PINSEL_CFG_Type PinCfg;
DAC_CONVERTER_CFG_Type DAC_ConverterConfigStruct;
GPDMA_LLI_Type DMA_LLI_Struct;
uint32_t tmp;
uint32_t i;
uint32_t sin_0_to_90_16_samples[16]={\
0,1045,2079,3090,4067,\
5000,5877,6691,7431,8090,\
8660,9135,9510,9781,9945,10000\
};
uint32_t dac_sine_lut[NUM_SINE_SAMPLE];
/*
* Init DAC pin connect
* AOUT on P0.26
*/
PinCfg.Funcnum = 2;
PinCfg.OpenDrain = 0;
PinCfg.Pinmode = 0;
PinCfg.Pinnum = 26;
PinCfg.Portnum = 0;
PINSEL_ConfigPin(&PinCfg);
//Prepare DAC sine look up table
for(i=0;i<NUM_SINE_SAMPLE;i++)
{
if(i<=15)
{
dac_sine_lut[i] = 512 + 512*sin_0_to_90_16_samples[i]/10000;
if(i==15) dac_sine_lut[i]= 1023;
}
else if(i<=30)
{
dac_sine_lut[i] = 512 + 512*sin_0_to_90_16_samples[30-i]/10000;
}
else if(i<=45)
{
dac_sine_lut[i] = 512 - 512*sin_0_to_90_16_samples[i-30]/10000;
}
else
{
dac_sine_lut[i] = 512 - 512*sin_0_to_90_16_samples[60-i]/10000;
}
dac_sine_lut[i] = (dac_sine_lut[i]<<6);
}
//Prepare DMA link list item structure
DMA_LLI_Struct.SrcAddr= (uint32_t)dac_sine_lut;
DMA_LLI_Struct.DstAddr= (uint32_t)&(LPC_DAC->DACR);
DMA_LLI_Struct.NextLLI= (uint32_t)&DMA_LLI_Struct;
DMA_LLI_Struct.Control= DMA_SIZE
| (2<<18) //source width 32 bit
| (2<<21) //dest. width 32 bit
| (1<<26) //source increment
;
/* GPDMA block section -------------------------------------------- */
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = (uint32_t)(dac_sine_lut);
// Destination memory - unused
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection
GPDMACfg.DstConn = GPDMA_CONN_DAC;
// Linker List Item - unused
GPDMACfg.DMALLI = (uint32_t)&DMA_LLI_Struct;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
DAC_ConverterConfigStruct.CNT_ENA =SET;
DAC_ConverterConfigStruct.DMA_ENA = SET;
DAC_Init(LPC_DAC);
/* set time out for DAC*/
tmp = (PCLK_DAC_IN_MHZ*1000000)/(SINE_FREQ_IN_HZ*NUM_SINE_SAMPLE);
DAC_SetDMATimeOut(LPC_DAC,tmp);
DAC_ConfigDAConverterControl(LPC_DAC, &DAC_ConverterConfigStruct);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
while (1);
return 1;
}
/**
* @brief Main program body
*/
int c_entry(void)
{
PINSEL_CFG_Type PinCfg;
GPDMA_Channel_CFG_Type GPDMACfg;
uint32_t adc_value, tmp;
// DeInit NVIC and SCBNVIC
NVIC_DeInit();
NVIC_SCBDeInit();
/* Configure the NVIC Preemption Priority Bits:
* two (2) bits of preemption priority, six (6) bits of sub-priority.
* Since the Number of Bits used for Priority Levels is five (5), so the
* actual bit number of sub-priority is three (3)
*/
NVIC_SetPriorityGrouping(0x05);
// Set Vector table offset value
#if (__RAM_MODE__==1)
NVIC_SetVTOR(0x10000000);
#else
NVIC_SetVTOR(0x00000000);
#endif
/*
* Initialize debug via UART
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/* GPDMA block section -------------------------------------------- */
/* Disable GPDMA interrupt */
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/*
* Init LPC_ADC pin connect
* AD0.2 on P0.25
*/
PinCfg.Funcnum = 1;
PinCfg.OpenDrain = 0;
PinCfg.Pinmode = 0;
PinCfg.Pinnum = 25;
PinCfg.Portnum = 0;
PINSEL_ConfigPin(&PinCfg);
/* Configuration for ADC :
* Frequency at 1Mhz
* ADC channel 2, generate interrupt to make a request for DMA source
*/
ADC_Init(LPC_ADC, 1000000);
ADC_IntConfig(LPC_ADC,ADC_ADINTEN2,SET);
ADC_ChannelCmd(LPC_ADC,ADC_CHANNEL_2,SET);
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = (uint32_t) &adc_value;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_ADC;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg, GPDMA_Callback);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
while (1) {
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
ADC_StartCmd(LPC_ADC,ADC_START_NOW);
/* Wait for GPDMA processing complete */;
while ((Channel0_TC == 0) );
// Disable GPDMA channel 0
GPDMA_ChannelCmd(0, DISABLE);
//Display the result of conversion on the UART0
_DBG("ADC value on channel 2: ");
_DBD32(ADC_DR_RESULT(adc_value));
_DBG_("");
// Wait for a while
for(tmp = 0; tmp < 1000000; tmp++);
// Re-setup channel
GPDMA_Setup(&GPDMACfg, GPDMA_Callback);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
}
ADC_DeInit(LPC_ADC);
return 1;
}
void LED_init(){
GPIO_SetDir(LED_OE_PORT, LED_OE_BIT, 1);
GPIO_SetValue(LED_OE_PORT, LED_OE_BIT);//turn off leds active low
LatchIn();//reset
GPIO_SetDir(LED_LE_PORT, LED_LE_BIT, 1);
GPIO_ClearValue(LED_LE_PORT, LED_LE_BIT);
//reset all arrays
for (uint8_t tmp=0;tmp<no_SEQ_BITS;tmp++){
SEQ_BIT[tmp] = BITORDER[tmp];
SEQ_TIME[tmp] = BITTIME[BITORDER[tmp]];
}
resetLeds();
calulateLEDMIBAMBits();
// Initialize SPI pin connect
PINSEL_CFG_Type PinCfg;
/* LE1 */
PinCfg.Funcnum = PINSEL_FUNC_0;
PinCfg.OpenDrain = PINSEL_PINMODE_NORMAL;
PinCfg.Pinmode = PINSEL_PINMODE_PULLDOWN;
PinCfg.Pinnum = LED_LE_PIN;
PinCfg.Portnum = LED_LE_PORT;
PINSEL_ConfigPin(&PinCfg);
/* SSEL1 */
PinCfg.Funcnum = PINSEL_FUNC_0;
PinCfg.OpenDrain = PINSEL_PINMODE_NORMAL;
PinCfg.Pinmode = PINSEL_PINMODE_PULLDOWN;
PinCfg.Pinnum = LED_OE_PIN;
PinCfg.Portnum = LED_OE_PORT;
PINSEL_ConfigPin(&PinCfg);
/* SCK1 */
PinCfg.Funcnum = PINSEL_FUNC_2;
PinCfg.OpenDrain = PINSEL_PINMODE_NORMAL;
PinCfg.Pinmode = PINSEL_PINMODE_PULLUP;
PinCfg.Pinnum = LED_SCK_PIN;
PinCfg.Portnum = LED_SCK_PORT;
PINSEL_ConfigPin(&PinCfg);
/* MISO1 */
PinCfg.Funcnum = PINSEL_FUNC_2;
PinCfg.OpenDrain = PINSEL_PINMODE_NORMAL;
PinCfg.Pinmode = PINSEL_PINMODE_PULLUP;
PinCfg.Pinnum = LED_MISO_PIN;
PinCfg.Portnum = LED_MISO_PORT;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Funcnum = PINSEL_FUNC_2;
/* MOSI1 */
PinCfg.Funcnum = PINSEL_FUNC_2;
PinCfg.OpenDrain = PINSEL_PINMODE_NORMAL;
PinCfg.Pinmode = PINSEL_PINMODE_PULLUP;
PinCfg.Pinnum = LED_MOSI_PIN;
PinCfg.Portnum = LED_MOSI_PORT;
PINSEL_ConfigPin(&PinCfg);
/* initialize SSP configuration structure */
SSP_CFG_Type SSP_ConfigStruct;
SSP_ConfigStruct.CPHA = SSP_CPHA_SECOND;
SSP_ConfigStruct.CPOL = SSP_CPOL_LO;
SSP_ConfigStruct.ClockRate = SSP_SPEED; // TLC5927 max freq = 30Mhz
SSP_ConfigStruct.FrameFormat = SSP_FRAME_SPI;
SSP_ConfigStruct.Databit = SSP_DATABIT_16;
SSP_ConfigStruct.Mode = SSP_MASTER_MODE;
SSP_Init(LED_SPI_CHN, &SSP_ConfigStruct);
SSP_Cmd(LED_SPI_CHN, ENABLE); // Enable SSP peripheral
// Setup LED interupt
// xprintf(INFO "LED TIM0_ConfigMatch");FFL_();
TIM_TIMERCFG_Type TIM0_ConfigStruct;
TIM_MATCHCFG_Type TIM0_MatchConfigStruct;
TIM0_ConfigStruct.PrescaleOption = TIM_PRESCALE_USVAL; // Initialize timer 0, prescale count time of 1us //1000000uS = 1S
TIM0_ConfigStruct.PrescaleValue = 1;
TIM0_MatchConfigStruct.MatchChannel = 0; // use channel 0, MR0
TIM0_MatchConfigStruct.IntOnMatch = TRUE; // Enable interrupt when MR0 matches the value in TC register
TIM0_MatchConfigStruct.ResetOnMatch = TRUE; //Enable reset on MR0: TIMER will reset if MR0 matches it
TIM0_MatchConfigStruct.StopOnMatch = FALSE; //Stop on MR0 if MR0 matches it
TIM0_MatchConfigStruct.ExtMatchOutputType = TIM_EXTMATCH_NOTHING;
TIM0_MatchConfigStruct.MatchValue = BITTIME[0]; // Set Match value, count value of 1000000 (1000000 * 1uS = 1000000us = 1s --> 1 Hz)
TIM_Init(LPC_TIM0, TIM_TIMER_MODE,&TIM0_ConfigStruct); // Set configuration for Tim_config and Tim_MatchConfig
TIM_ConfigMatch(LPC_TIM0,&TIM0_MatchConfigStruct);
NVIC_SetPriority(TIMER0_IRQn, 0);
NVIC_EnableIRQ(TIMER0_IRQn);
// xprintf(OK "LED TIM0_ConfigMatch");FFL_();
// Setup LED Latch interupt
// xprintf(INFO "LED TIM1_ConfigMatch");FFL_();
TIM_TIMERCFG_Type TIM1_ConfigStruct;
TIM_MATCHCFG_Type TIM1_MatchConfigStruct;
TIM1_ConfigStruct.PrescaleOption = TIM_PRESCALE_TICKVAL; // Initialize timer 0, prescale count time of 1us //1000000uS = 1S
TIM1_ConfigStruct.PrescaleValue = 1;
TIM1_MatchConfigStruct.MatchChannel = 0; // use channel 0, MR0
TIM1_MatchConfigStruct.IntOnMatch = TRUE; // Enable interrupt when MR0 matches the value in TC register
TIM1_MatchConfigStruct.ResetOnMatch = TRUE; //Enable reset on MR0: TIMER will reset if MR0 matches it
TIM1_MatchConfigStruct.StopOnMatch = TRUE; //Stop on MR0 if MR0 matches it
TIM1_MatchConfigStruct.ExtMatchOutputType = TIM_EXTMATCH_NOTHING;
TIM1_MatchConfigStruct.MatchValue = LED_Latch_interupt_delay; // Set Match value, count value of 1000000 (1000000 * 1uS = 1000000us = 1s --> 1 Hz)
TIM_Init(LPC_TIM1, TIM_TIMER_MODE,&TIM1_ConfigStruct); // Set configuration for Tim_config and Tim_MatchConfig
TIM_ConfigMatch(LPC_TIM1,&TIM1_MatchConfigStruct);
NVIC_SetPriority(TIMER1_IRQn, 0);
NVIC_EnableIRQ(TIMER1_IRQn);
// xprintf(OK "LED TIM1_ConfigMatch");FFL_();
// Speed timer
// xprintf(INFO "LED TIM2_ConfigMatch");FFL_();
TIM_TIMERCFG_Type TIM2_ConfigStruct;
TIM_MATCHCFG_Type TIM2_MatchConfigStruct;
TIM2_ConfigStruct.PrescaleOption = TIM_PRESCALE_USVAL; // Initialize timer 0, prescale count time of 1us //1000000uS = 1S
TIM2_ConfigStruct.PrescaleValue = 1000;
TIM2_MatchConfigStruct.MatchChannel = 0; // use channel 0, MR0
TIM2_MatchConfigStruct.IntOnMatch = TRUE; // Enable interrupt when MR0 matches the value in TC register
TIM2_MatchConfigStruct.ResetOnMatch = TRUE; //Enable reset on MR0: TIMER will reset if MR0 matches it
TIM2_MatchConfigStruct.StopOnMatch = FALSE; //Stop on MR0 if MR0 matches it
TIM2_MatchConfigStruct.ExtMatchOutputType = TIM_EXTMATCH_NOTHING;
TIM2_MatchConfigStruct.MatchValue = 256; // Set Match value, count value of 1000000 (1000000 * 1uS = 1000000us = 1s --> 1 Hz)
TIM_Init(LPC_TIM2, TIM_TIMER_MODE,&TIM2_ConfigStruct); // Set configuration for Tim_config and Tim_MatchConfig
TIM_ConfigMatch(LPC_TIM2,&TIM2_MatchConfigStruct);
NVIC_SetPriority(TIMER2_IRQn, 0);
NVIC_EnableIRQ(TIMER2_IRQn);
// xprintf(OK "LED TIM2_ConfigMatch");FFL_();
#ifdef DMA
// GPDMA_Channel_CFG_Type GPDMACfg;
NVIC_SetPriority(DMA_IRQn, 0); // set according to main.c
NVIC_EnableIRQ(DMA_IRQn);
GPDMA_Init(); // Initialize GPDMA controller */
NVIC_DisableIRQ (DMA_IRQn); // Disable interrupt for DMA
NVIC_SetPriority(DMA_IRQn, 0); // set according to main.c
GPDMACfg.ChannelNum = 0; // DMA Channel 0
GPDMACfg.SrcMemAddr = 0; // Source memory - not used - will be sent in interrupt so independent bit Linker Lists can be chosen
GPDMACfg.DstMemAddr = 0; // Destination memory - not used - only used when destination is memory
GPDMACfg.TransferSize = 1; // Transfer size
GPDMACfg.TransferWidth = GPDMA_WIDTH_HALFWORD; // Transfer width - not used
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P; // Transfer type
GPDMACfg.SrcConn = 0; // Source connection - not used
GPDMACfg.DstConn = GPDMA_CONN_SSP0_Tx; // Destination connection - not used
GPDMACfg.DMALLI = (uint32_t) &LinkerList[0][0][0]; // Linker List Item - Pointer to linker list
GPDMA_Setup(&GPDMACfg); // Setup channel with given parameter
// Linker list 32bit Control
uint32_t LinkerListControl = 0;
LinkerListControl = GPDMA_DMACCxControl_TransferSize((uint32_t)GPDMACfg.TransferSize) \
| GPDMA_DMACCxControl_SBSize((uint32_t)GPDMA_BSIZE_1) \
| GPDMA_DMACCxControl_DBSize((uint32_t)GPDMA_BSIZE_1) \
| GPDMA_DMACCxControl_SWidth((uint32_t)GPDMACfg.TransferWidth) \
| GPDMA_DMACCxControl_DWidth((uint32_t)GPDMACfg.TransferWidth) \
| GPDMA_DMACCxControl_SI;
uint8_t reg, bit, linkerListNo, buf;
for (buf=0;buf<BUFFERS;buf++){
for (bit=0;bit<BITS;bit++){
linkerListNo=0;
for (reg=5; 0<reg;reg--,linkerListNo++){
// xprintf("bit:%d reg:%d SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x linkerListNo:0x%x\n",bit,reg,(uint32_t) &LED_PRECALC[reg][bit][buf],(uint32_t) &LPC_SSP0->DR,(uint32_t) &LinkerList[linkerListNo+1][bit][buf],linkerListNo);
LinkerList[linkerListNo][bit][buf].SrcAddr = (uint32_t) &LED_PRECALC[reg][bit][buf]; /**< Source Address */
LinkerList[linkerListNo][bit][buf].DstAddr = (uint32_t) &LPC_SSP0->DR; /**< Destination address */
LinkerList[linkerListNo][bit][buf].NextLLI = (uint32_t) &LinkerList[linkerListNo+1][bit][buf]; /**< Next LLI address, otherwise set to '0' */
LinkerList[linkerListNo][bit][buf].Control = LinkerListControl;
// xprintf("SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x\n",(uint32_t) &LinkerList[linkerListNo][bit][buf].SrcAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].DstAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].NextLLI,(uint32_t) &LinkerList[linkerListNo][bit][buf].Control);
}
// if (reg==0){
// xprintf("bit:%d reg:%d SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x linkerListNo:0x%x\n",bit,reg,(uint32_t) &LED_PRECALC[reg][bit][buf],(uint32_t) &LPC_SSP0->DR,(uint32_t) &LinkerList[linkerListNo+1][bit][buf],linkerListNo);
LinkerList[linkerListNo][bit][buf].SrcAddr = (uint32_t) &LED_PRECALC[reg][bit][buf]; /**< Source Address */
LinkerList[linkerListNo][bit][buf].DstAddr = (uint32_t) &LPC_SSP0->DR; /**< Destination address */
LinkerList[linkerListNo][bit][buf].NextLLI = (uint32_t) &LinkerList[linkerListNo+1][bit][buf];/**< Next LLI address, otherwise set to '0' */
LinkerList[linkerListNo][bit][buf].Control = LinkerListControl;
linkerListNo++;
// xprintf("SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x\n",(uint32_t) &LinkerList[linkerListNo][bit][buf].SrcAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].DstAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].NextLLI,(uint32_t) &LinkerList[linkerListNo][bit][buf].Control);
// }
for (reg=11; reg>6;reg--,linkerListNo++){
// xprintf("bit:%d reg:%d SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x linkerListNo:0x%x\n",bit,reg,(uint32_t) &LED_PRECALC[reg][bit][buf],(uint32_t) &LPC_SSP0->DR,(uint32_t) &LinkerList[linkerListNo+1][bit][buf],linkerListNo);
LinkerList[linkerListNo][bit][buf].SrcAddr = (uint32_t) &LED_PRECALC[reg][bit][buf]; /**< Source Address */
LinkerList[linkerListNo][bit][buf].DstAddr = (uint32_t) &LPC_SSP0->DR; /**< Destination address */
LinkerList[linkerListNo][bit][buf].NextLLI = (uint32_t) &LinkerList[linkerListNo+1][bit][buf]; /**< Next LLI address, otherwise set to '0' */
LinkerList[linkerListNo][bit][buf].Control = LinkerListControl;
// xprintf("SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x\n",(uint32_t) &LinkerList[linkerListNo][bit][buf].SrcAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].DstAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].NextLLI,(uint32_t) &LinkerList[linkerListNo][bit][buf].Control);
}
// if (reg==7){
// xprintf("bit:%d reg:%d SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x linkerListNo:0x%x\n",bit,reg,(uint32_t) &LED_PRECALC[reg][bit][buf],(uint32_t) &LPC_SSP0->DR,(uint32_t) &LinkerList[linkerListNo+1][bit][buf],linkerListNo);
LinkerList[linkerListNo][bit][buf].SrcAddr = (uint32_t) &LED_PRECALC[reg][bit][buf]; /**< Source Address */
LinkerList[linkerListNo][bit][buf].DstAddr = (uint32_t) &LPC_SSP0->DR; /**< Destination address */
LinkerList[linkerListNo][bit][buf].NextLLI = 0; /**< Next LLI address, otherwise set to '0' */
LinkerList[linkerListNo][bit][buf].Control = LinkerListControl;
linkerListNo++;
// xprintf("SrcAddr:0x%x DstAddr:0x%x NextLLI:0x%x NextLLI_V:0x%x\n",(uint32_t) &LinkerList[linkerListNo][bit][buf].SrcAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].DstAddr,(uint32_t) &LinkerList[linkerListNo][bit][buf].NextLLI,LinkerList[linkerListNo][bit][buf].NextLLI);
// }
}
}
SSP_DMACmd (LED_SPI_CHN, SSP_DMA_TX, ENABLE); // Enable Tx DMA on SSP0
// GPDMA_ChannelCmd(0, ENABLE); // Enable GPDMA channel 0
NVIC_EnableIRQ (DMA_IRQn); // Enable interrupt for DMA
xprintf(OK "DMA Setup");FFL_();
TIM_Cmd(LPC_TIM0,ENABLE); // To start timer 0
// TIM_Cmd(LPC_TIM1,ENABLE); // To start timer 1 //done at DMA end
TIM_Cmd(LPC_TIM2,ENABLE); // To start timer 2
xprintf(OK "TIM_Cmd(LPC_TIM0/2,ENABLE);");FFL_();
// Start LED Pattern
uint8_t pot = 65;
Set_LED_Pattern(1,121,pot);
xprintf(OK "LED Pattern Started");FFL_();
#endif
#ifdef RxDMA // SSP Rx DMA
GPDMA_Channel_CFG_Type GPDMACfg1;
/* Configure GPDMA channel 1 -------------------------------------------------------------*/
GPDMACfg1.ChannelNum = 1; // DMA Channel 0
GPDMACfg1.SrcMemAddr = 0; // Source memory - not used - will be sent in interrupt so independent bit Linker Lists can be chosen
GPDMACfg1.DstMemAddr = (uint32_t) &LED_PRECALC1[0][0]; // Destination memory - not used - only used when destination is memory
GPDMACfg1.TransferSize = 1; // Transfer size
GPDMACfg1.TransferWidth = GPDMA_WIDTH_HALFWORD; // Transfer width
GPDMACfg1.TransferType = GPDMA_TRANSFERTYPE_P2M; // Transfer type
GPDMACfg1.SrcConn = GPDMA_CONN_SSP0_Rx; // Source connection - not used
GPDMACfg1.DstConn = 0; // Destination connection - not used
GPDMACfg1.DMALLI = 0; // Linker List Item - Pointer to linker list
GPDMA_Setup(&GPDMACfg1); // Setup channel with given parameter
Channel1_TC = 0; // Reset terminal counter
Channel1_Err = 0; // Reset Error counter
xprintf(OK "DMA Rx Setup");FFL_();
// SSP_DMACmd (LED_SPI_CHN, SSP_DMA_RX, ENABLE); // Enable Tx DMA on SSP0
// GPDMA_ChannelCmd(1, ENABLE); // Enable GPDMA channel 0
#endif
}
/*********************************************************************//**
* @brief c_entry: Main ADC program body
* @param[in] None
* @return None
**********************************************************************/
void c_entry(void)
{
volatile uint32_t tmp;
#if !__DMA_USED__
uint32_t adc_value;
#endif
uint8_t quit;
EXTI_InitTypeDef EXTICfg;
#if __DMA_USED__
GPDMA_Channel_CFG_Type GPDMACfg;
#endif
GPIO_Init();
/* Initialize debug via UART0
* – 115200bps
* – 8 data bit
* – No parity
* – 1 stop bit
* – No flow control
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/*
* Init ADC pin connect
* AD0.2 on P0.25
*/
PINSEL_ConfigPin(BRD_ADC_PREPARED_CH_PORT, BRD_ADC_PREPARED_CH_PIN, BRD_ADC_PREPARED_CH_FUNC_NO);
PINSEL_SetAnalogPinMode(BRD_ADC_PREPARED_CH_PORT,BRD_ADC_PREPARED_CH_PIN,ENABLE);
#ifdef LPC177x_8x_ADC_BURST_MULTI
/*
* Init ADC pin connect
* AD0.3 on P0.26
*/
PINSEL_ConfigPin(0, 26, 1);
PINSEL_SetAnalogPinMode(0,26,ENABLE);
#endif
/* Configuration for ADC:
* select: ADC channel 2
* ADC channel 3
* ADC conversion rate = 400KHz
*/
ADC_Init(LPC_ADC, 400000);
ADC_ChannelCmd(LPC_ADC,BRD_ADC_PREPARED_CHANNEL,ENABLE);
#ifdef LPC177x_8x_ADC_BURST_MULTI
ADC_ChannelCmd(LPC_ADC,_ADC_CHANNEL_n,ENABLE);
#endif
#ifdef LPC177x_8x_ADC_INJECT_TEST
//Config P2.10 as EINT0
PINSEL_ConfigPin(2,10,1);
EXTI_Init();
EXTICfg.EXTI_Line = EXTI_EINT0;
/* edge sensitive */
EXTICfg.EXTI_Mode = EXTI_MODE_EDGE_SENSITIVE;
EXTICfg.EXTI_polarity = EXTI_POLARITY_LOW_ACTIVE_OR_FALLING_EDGE;
EXTI_Config(&EXTICfg);
GPIO_SetDir(LED_PORT,LED_PIN,1);
GPIO_SetValue(LED_PORT,LED_PIN);
NVIC_EnableIRQ(EINT0_IRQn);
#endif
#if __DMA_USED__
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = (uint32_t)s_buf;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_ADC;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
while(1)
{
for(tmp = 0; tmp < 0x1000; tmp++);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
for(tmp = 0; tmp < DMA_SIZE; tmp++)
{
s_buf[tmp] = 0;
}
//Start burst conversion
ADC_BurstCmd(LPC_ADC,ENABLE);
GPDMA_Setup(&GPDMACfg);
// Enable GPDMA channel 1
GPDMA_ChannelCmd(0, ENABLE);
/* Wait for GPDMA processing complete */
while ((Channel0_TC == 0));
GPDMA_ChannelCmd(0, DISABLE);
for(tmp = 0; tmp < DMA_SIZE; tmp++)
{
if(s_buf[tmp] & ADC_GDR_DONE_FLAG)
{
_DBG("ADC value on channel "); _DBD(ADC_GDR_CH(s_buf[tmp])); _DBG(": ");
_DBD32(ADC_GDR_RESULT(s_buf[tmp]));_DBG_("");
}
}
if(_DG_NONBLOCK(&quit) &&
(quit == 'Q' || quit == 'q'))
break;
}
#else
//Start burst conversion
ADC_BurstCmd(LPC_ADC,ENABLE);
while(1)
{
adc_value = ADC_ChannelGetData(LPC_ADC,BRD_ADC_PREPARED_CHANNEL);
_DBG("ADC value on channel "); _DBD(BRD_ADC_PREPARED_CHANNEL); _DBG(": ");
_DBD32(adc_value);
_DBG_("");
#ifdef LPC177x_8x_ADC_BURST_MULTI
adc_value = ADC_ChannelGetData(LPC_ADC,_ADC_CHANNEL_n);
_DBG("ADC value on channel 3: ");
_DBD32(adc_value);
_DBG_("");
#endif
// Wait for a while
for(tmp = 0; tmp < 1500000; tmp++);
if(_DG_NONBLOCK(&quit) &&
(quit == 'Q' || quit == 'q'))
break;
}
#endif /*__DMA_USED__*/
_DBG_("Demo termination!!!");
ADC_DeInit(LPC_ADC);
GPIO_Deinit();
}
/*********************************************************************//**
* @brief c_entry: Main DAC program body
* @param[in] None
* @return None
**********************************************************************/
void c_entry(void)
{
DAC_CONVERTER_CFG_Type DAC_ConverterConfigStruct;
uint32_t dac_value = 0;
volatile uint32_t i;
/* GPDMA block section -------------------------------------------- */
/* Disable GPDMA interrupt */
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01 << 3) | 0x01));
DAC_ConverterConfigStruct.CNT_ENA =SET;
DAC_ConverterConfigStruct.DMA_ENA = SET;
DAC_Init(0);
/* set time out for DAC*/
DAC_SetDMATimeOut(0, 0xFFFF);
DAC_ConfigDAConverterControl(0, &DAC_ConverterConfigStruct);
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = (uint32_t)(&dac_value);
// Destination memory - unused
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection
GPDMACfg.DstConn = GPDMA_CONN_DAC;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
/* Wait for GPDMA processing complete */
while (1)
{
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
while ((Channel0_TC == 0) );
// Disable GPDMA channel 0
GPDMA_ChannelCmd(0, DISABLE);
dac_value ++;
if (dac_value == 0x3FF)
dac_value = 0;
//delay
for(i=0;i<100000;i++);
/* Reset terminal counter */
Channel0_TC = 0;
// Re-setup channel
GPDMA_Setup(&GPDMACfg);
}
}
/*********************************************************************//**
* @brief c_entry: Main SSP program body
* @param[in] None
* @return int
**********************************************************************/
int c_entry(void)
{
#if __DMA_USED__
GPDMA_Channel_CFG_Type GPDMACfg;
#else
SSP_DATA_SETUP_Type xferConfig;
#endif
/*
* Initialize SSP pin connect
* P0.15 - SCK;
* P0.16 - SSEL
* P0.17 - MISO
* P0.18 - MOSI
*/
#if (_SSP_NO_USING == 0)
PINSEL_ConfigPin(0, 15, 2);
PINSEL_ConfigPin(0, 16, 2);
PINSEL_ConfigPin(0, 17, 2);
PINSEL_ConfigPin(0, 18, 2);
#elif (_SSP_NO_USING == 1)
PINSEL_ConfigPin(0, 6, 2);
PINSEL_ConfigPin(0, 7, 2);
PINSEL_SetFilter(0, 7, 0);
PINSEL_ConfigPin(0, 8, 2);
PINSEL_SetFilter(0, 8, 0);
PINSEL_ConfigPin(0, 9, 2);
PINSEL_SetFilter(0, 9, 0);
#else
PINSEL_ConfigPin(1, 0, 4);
PINSEL_ConfigPin(1, 8, 4);
PINSEL_ConfigPin(1, 1, 4);
PINSEL_ConfigPin(1, 4, 4);
#endif
/* Initialize debug via UART0
* – 115200bps
* – 8 data bit
* – No parity
* – 1 stop bit
* – No flow control
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
// initialize SSP configuration structure to default
SSP_ConfigStructInit(&SSP_ConfigStruct);
// Initialize SSP peripheral with parameter given in structure above
SSP_Init(LPC_SSP, &SSP_ConfigStruct);
// Enable SSP peripheral
SSP_Cmd(LPC_SSP, ENABLE);
_DBG_("Press '1' to start transfer...");
while (_DG != '1');
/* Initialize Buffer */
_DBG_("Init buffer");
Buffer_Init();
_DBG_("Start transfer...");
#if __DMA_USED__
/* Initialize GPDMA controller */
GPDMA_Init();
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ (DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Configure GPDMA channel 0 -------------------------------------------------------------*/
/* DMA Channel 0 */
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = (uint32_t) &Tx_Buf;
// Destination memory - Not used
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = sizeof(Tx_Buf);
// Transfer width - not used
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection
GPDMACfg.DstConn = SSP_TX_SRC_DMA_CONN;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/* Configure GPDMA channel 1 -------------------------------------------------------------*/
/* DMA Channel 1 */
GPDMACfg.ChannelNum = 1;
// Source memory - not used
GPDMACfg.SrcMemAddr = 0;
// Destination memory - Not used
GPDMACfg.DstMemAddr = (uint32_t) &Rx_Buf;
// Transfer size
GPDMACfg.TransferSize = sizeof(Rx_Buf);
// Transfer width - not used
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = SSP_RX_SRC_DMA_CONN;
// Destination connection - not used
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel1_TC = 0;
/* Reset Error counter */
Channel1_Err = 0;
// Enable Tx and Rx DMA on SSP0
SSP_DMACmd (LPC_SSP, SSP_DMA_RX, ENABLE);
SSP_DMACmd (LPC_SSP, SSP_DMA_TX, ENABLE);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(1, ENABLE);
// Enable interrupt for DMA
NVIC_EnableIRQ (DMA_IRQn);
/* Wait for GPDMA processing complete */
while (((Channel0_TC == 0) && (Channel0_Err == 0)) \
|| ((Channel1_TC == 0) && (Channel1_Err ==0)));
#else
xferConfig.tx_data = Tx_Buf;
xferConfig.rx_data = Rx_Buf;
xferConfig.length = BUFFER_SIZE;
SSP_ReadWrite(LPC_SSP, &xferConfig, SSP_TRANSFER_POLLING);
#endif
// Verify buffer after transferring
Buffer_Verify();
_DBG_("Verify complete!");
/* Loop forever */
while(1);
}
/*********************************************************************//**
* @brief c_entry: Main program body
* @param[in] None
* @return int
**********************************************************************/
int c_entry(void)
{
uint32_t i;
GPDMA_Channel_CFG_Type GPDMACfg;
I2S_MODEConf_Type I2S_ClkConfig;
I2S_CFG_Type I2S_ConfigStruct;
I2S_DMAConf_Type I2S_DMAStruct;
PINSEL_CFG_Type PinCfg;
/* Initialize debug via UART0
* – 115200bps
* – 8 data bit
* – No parity
* – 1 stop bit
* – No flow control
*/
debug_frmwrk_init();
//print menu screen
print_menu();
//Initialize buffer
Buffer_Init();
_DBG_("Press '1' to initialize buffer...");
while(_DG !='1');
_DBG_("Transmit Buffer init: ...");
for(i=0;i<BUFFER_SIZE;i++)
{
_DBH32(I2STXBuffer[i]);_DBG_("");
}
_DBG_("Receive Buffer init: ...");
for(i=0;i<BUFFER_SIZE;i++)
{
_DBH32(I2SRXBuffer[i]);_DBG_("");
}
/* Pin configuration:
* Assign: - P0.4 as I2SRX_CLK
* - P0.5 as I2SRX_WS
* - P0.6 as I2SRX_SDA
* - P0.7 as I2STX_CLK
* - P0.8 as I2STX_WS
* - P0.9 as I2STX_SDA
*/
PinCfg.Funcnum = 1;
PinCfg.OpenDrain = 0;
PinCfg.Pinmode = 0;
PinCfg.Pinnum = 4;
PinCfg.Portnum = 0;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 5;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 6;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 7;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 8;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 9;
PINSEL_ConfigPin(&PinCfg);
/* Initialize I2S */
I2S_Init(LPC_I2S);
//Setup for I2S: RX is similar with TX
/* setup:
* - wordwidth: 16 bits
* - stereo mode
* - master mode for I2S_TX and slave for I2S_RX
* - ws_halfperiod is 31
* - not use mute mode
* - use reset and stop mode
* - select the fractional rate divider clock output as the source,
* - disable 4-pin mode
* - MCLK ouput is disable
* - Frequency = 44.1 kHz
* Because we use mode I2STXMODE[3:0]= 0000, I2SDAO[5]=0 and
* I2SRX[3:0]=0000, I2SDAI[5] = 1. So we have I2SRX_CLK = I2STX_CLK
* --> I2SRXBITRATE = 1 (not divide TXCLK to produce RXCLK)
*/
/* Audio Config*/
I2S_ConfigStruct.wordwidth = I2S_WORDWIDTH_16;
I2S_ConfigStruct.mono = I2S_STEREO;
I2S_ConfigStruct.stop = I2S_STOP_ENABLE;
I2S_ConfigStruct.reset = I2S_RESET_ENABLE;
I2S_ConfigStruct.ws_sel = I2S_MASTER_MODE;
I2S_ConfigStruct.mute = I2S_MUTE_DISABLE;
I2S_Config(LPC_I2S,I2S_TX_MODE,&I2S_ConfigStruct);
I2S_ConfigStruct.ws_sel = I2S_SLAVE_MODE;
I2S_Config(LPC_I2S,I2S_RX_MODE,&I2S_ConfigStruct);
/* Clock Mode Config*/
I2S_ClkConfig.clksel = I2S_CLKSEL_FRDCLK;
I2S_ClkConfig.fpin = I2S_4PIN_DISABLE;
I2S_ClkConfig.mcena = I2S_MCLK_DISABLE;
I2S_ModeConfig(LPC_I2S,&I2S_ClkConfig,I2S_TX_MODE);
I2S_ModeConfig(LPC_I2S,&I2S_ClkConfig,I2S_RX_MODE);
/* Set up frequency and bit rate*/
I2S_FreqConfig(LPC_I2S, 44100, I2S_TX_MODE);
I2S_SetBitRate(LPC_I2S, 0, I2S_RX_MODE);
_DBG_("Press '2' to initialize DMA...");
while(_DG !='2');
/* GPDMA Interrupt configuration section ------------------------------------------------- */
/* Initialize GPDMA controller */
GPDMA_Init();
LPC_GPDMA->DMACConfig = 0x01;
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ (DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/*
* Configure GPDMA channel 0 -------------------------------------------------------------
* Used for I2S Transmit
*/
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = DMA_SRC;
// Destination memory
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = BUFFER_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection
GPDMACfg.SrcConn = 0;
// Destination connection - unused
GPDMACfg.DstConn = GPDMA_CONN_I2S_Channel_0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
GPDMA_Setup(&GPDMACfg);
_DBG_("DMA Channel 0 setting finised...");
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/*
* Configure GPDMA channel 1 -------------------------------------------------------------
* Used for UART0 Receive
*/
// Setup GPDMA channel --------------------------------
// channel 1
GPDMACfg.ChannelNum = 1;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = DMA_DST;
// Transfer size
GPDMACfg.TransferSize = BUFFER_SIZE+1;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection - unused
GPDMACfg.SrcConn = GPDMA_CONN_I2S_Channel_1;
// Destination connection
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
GPDMA_Setup(&GPDMACfg);
_DBG_("DMA Channel 1 setting finised...");
/* Reset terminal counter */
Channel1_TC = 0;
/* Reset Error counter */
Channel1_Err = 0;
// Enable GPDMA channel 0 & 1
GPDMA_ChannelCmd(0, ENABLE);
GPDMA_ChannelCmd(1, ENABLE);
// Enable interrupt for DMA
NVIC_EnableIRQ (DMA_IRQn);
_DBG_("Press '3' to start I2S transfer process...");
while(_DG !='3');
_DBG_("I2S Start...");
I2S_DMAStruct.DMAIndex = I2S_DMA_2;
I2S_DMAStruct.depth = 8;
I2S_DMAConfig(LPC_I2S, &I2S_DMAStruct, I2S_RX_MODE);
I2S_DMAStruct.DMAIndex = I2S_DMA_1;
I2S_DMAStruct.depth = 1;
I2S_DMAConfig(LPC_I2S, &I2S_DMAStruct, I2S_TX_MODE);
I2S_Start(LPC_I2S);
I2S_DMACmd(LPC_I2S, I2S_DMA_2, I2S_RX_MODE, ENABLE);
I2S_DMACmd(LPC_I2S, I2S_DMA_1, I2S_TX_MODE, ENABLE);
while ((Channel0_TC == 0)||(Channel1_TC == 0) );
_DBG_("I2S Finish...");
_DBG_("Receive Buffer data: ...");
for(i=0;i<BUFFER_SIZE+1;i++)
{
_DBH32(I2SRXBuffer[i]);
if(I2SRXBuffer[i]==0)
{
_DBG_(" ->Dummy data");
}
else _DBG_("");
}
I2S_DeInit(LPC_I2S);
while(1);
return 1;
}
/*********************************************************************//**
* @brief c_entry: Main ADC program body
* @param[in] None
* @return None
**********************************************************************/
void c_entry(void)
{
GPDMA_Channel_CFG_Type GPDMACfg;
volatile uint32_t adc_value, tmp;
uint8_t quit;
/* Initialize debug via UART0
* ?115200bps
* ?8 data bit
* ?No parity
* ?1 stop bit
* ?No flow control
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/* Initialize ADC ----------------------------------------------------*/
/* Settings for AD input pin
*/
PINSEL_ConfigPin (BRD_ADC_PREPARED_CH_PORT, BRD_ADC_PREPARED_CH_PIN, BRD_ADC_PREPARED_CH_FUNC_NO);
PINSEL_SetAnalogPinMode(BRD_ADC_PREPARED_CH_PORT,BRD_ADC_PREPARED_CH_PIN,ENABLE);
/* Configuration for ADC :
* ADC conversion rate = 400KHz
*/
ADC_Init(LPC_ADC, 400000);
ADC_IntConfig(LPC_ADC, BRD_ADC_PREPARED_INTR, ENABLE);
ADC_ChannelCmd(LPC_ADC, BRD_ADC_PREPARED_CHANNEL, ENABLE);
/* GPDMA block section -------------------------------------------- */
/* Disable GPDMA interrupt */
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = (uint32_t) &adc_value;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_ADC;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
while (1)
{
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
ADC_StartCmd(LPC_ADC, ADC_START_NOW);
/* Wait for GPDMA processing complete */
while ((Channel0_TC == 0));
// Disable GPDMA channel 0
GPDMA_ChannelCmd(0, DISABLE);
//Display the result of conversion on the UART
_DBG("ADC value on channel "); _DBD(BRD_ADC_PREPARED_CHANNEL);
_DBG(" is: "); _DBD32(ADC_DR_RESULT(adc_value)); _DBG_("");
// Wait for a while
for(tmp = 0; tmp < 1000000; tmp++);
/* GPDMA Re-setup */
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
if(_DG_NONBLOCK(&quit) &&
(quit == 'Q' || quit == 'q'))
break;
}
_DBG_("Demo termination!!!");
ADC_DeInit(LPC_ADC);
}
/*********************************************************************//**
* @brief c_entry: Main program body
* @param[in] None
* @return int
**********************************************************************/
int c_entry(void)
{
GPDMA_Channel_CFG_Type GPDMACfg;
/* Initialize debug via UART0
* – 115200bps
* – 8 data bit
* – No parity
* – 1 stop bit
* – No flow control
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/* GPDMA block section -------------------------------------------- */
/* Initialize buffer */
_DBG_("Initialize Buffer...");
Buffer_Init();
/* Disable GPDMA interrupt */
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = DMA_SRC;
// Destination memory
GPDMACfg.DstMemAddr = DMA_DST;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width
GPDMACfg.TransferWidth = GPDMA_WIDTH_WORD;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2M;
// Source connection - unused
GPDMACfg.SrcConn = 0;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
_DBG_("Start transfer...");
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
/* Wait for GPDMA processing complete */
while ((Channel0_TC == 0) && (Channel0_Err == 0));
/* Verify buffer */
Buffer_Verify();
_DBG(compl_menu);
/* Loop forever */
while(1);
return 1;
}
/*********************************************************************//**
* @brief c_entry: Main UART program body
* @param[in] None
* @return int
**********************************************************************/
int c_entry(void)
{
uint8_t *rx_char;
uint32_t idx;
// UART Configuration structure variable
UART_CFG_Type UARTConfigStruct;
// UART FIFO configuration Struct variable
UART_FIFO_CFG_Type UARTFIFOConfigStruct;
GPDMA_Channel_CFG_Type GPDMACfg;
// Pin configuration for UART0
PINSEL_CFG_Type PinCfg;
/*
* Initialize UART0 pin connect
*/
PinCfg.Funcnum = 1;
PinCfg.OpenDrain = 0;
PinCfg.Pinmode = 0;
PinCfg.Pinnum = 2;
PinCfg.Portnum = 0;
PINSEL_ConfigPin(&PinCfg);
PinCfg.Pinnum = 3;
PINSEL_ConfigPin(&PinCfg);
/* Initialize UART Configuration parameter structure to default state:
* Baudrate = 9600bps
* 8 data bit
* 1 Stop bit
* None parity
*/
UART_ConfigStructInit(&UARTConfigStruct);
// Initialize UART0 peripheral with given to corresponding parameter
UART_Init(LPC_UART0, &UARTConfigStruct);
/* Initialize FIFOConfigStruct to default state:
* - FIFO_DMAMode = DISABLE
* - FIFO_Level = UART_FIFO_TRGLEV0
* - FIFO_ResetRxBuf = ENABLE
* - FIFO_ResetTxBuf = ENABLE
* - FIFO_State = ENABLE
*/
UART_FIFOConfigStructInit(&UARTFIFOConfigStruct);
// Enable DMA mode in UART
UARTFIFOConfigStruct.FIFO_DMAMode = ENABLE;
// Initialize FIFO for UART0 peripheral
UART_FIFOConfig(LPC_UART0, &UARTFIFOConfigStruct);
// Enable UART Transmit
UART_TxCmd(LPC_UART0, ENABLE);
/* GPDMA Interrupt configuration section ------------------------------------------------- */
/* Initialize GPDMA controller */
GPDMA_Init();
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ (DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01<<3)|0x01));
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory
GPDMACfg.SrcMemAddr = (uint32_t) &menu1;
// Destination memory - don't care
GPDMACfg.DstMemAddr = 0;
// Transfer size
GPDMACfg.TransferSize = sizeof(menu1);
// Transfer width - don't care
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
// Source connection - don't care
GPDMACfg.SrcConn = 0;
// Destination connection
GPDMACfg.DstConn = GPDMA_CONN_UART0_Tx;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
// Setup GPDMA channel --------------------------------
// channel 1
GPDMACfg.ChannelNum = 1;
// Source memory - don't care
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = (uint32_t) &rx_buf;
// Transfer size
GPDMACfg.TransferSize = sizeof(rx_buf);
// Transfer width - don't care
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_UART0_Rx;
// Destination connection - don't care
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
GPDMA_Setup(&GPDMACfg);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
// Enable interrupt for DMA
NVIC_EnableIRQ (DMA_IRQn);
// Enable GPDMA channel 0
GPDMA_ChannelCmd(0, ENABLE);
// Make sure GPDMA channel 1 is disabled
GPDMA_ChannelCmd(1, DISABLE);
/* Wait for GPDMA on UART0 Tx processing complete */
while ((Channel0_TC == 0) && (Channel0_Err == 0));
// Main loop - echos back to the terminal
while (1)
{
/* Reset terminal counter */
Channel1_TC = 0;
/* Reset Error counter */
Channel1_Err = 0;
// Setup channel with given parameter
GPDMA_Setup(&GPDMACfg);
// Enable GPDMA channel 1
GPDMA_ChannelCmd(1, ENABLE);
// Clear Rx buffer using DMA
for (idx = 0; idx < RX_BUF_SIZE; idx++){
rx_buf[idx] = 0;
}
// now, start receive character using GPDMA
rx_char = (uint8_t *) &rx_buf;
while ((Channel1_TC == 0) && (Channel1_Err == 0)){
// Check whether if there's any character received, then print it back
if (*rx_char != 0)
{
UART_Send(LPC_UART0, rx_char, 1, BLOCKING);
rx_char++;
}
}
}
// DeInitialize UART0 peripheral
UART_DeInit(LPC_UART0);
/* Loop forever */
while(1);
return 1;
}
void initI2SDMA(uint32_t txblock, uint32_t rxblock) {
I2S_DMAConf_Type I2SDMACfg;
GPDMA_Channel_CFG_Type GPDMACfg;
/* Initialize GPDMA controller */
GPDMA_Init();
LPC_GPDMA->DMACConfig = 0x01;
/* Setting GPDMA interrupt */
// Disable interrupt for DMA
NVIC_DisableIRQ(DMA_IRQn);
/* preemption = 1, sub-priority = 1 */
NVIC_SetPriority(DMA_IRQn, ((0x01 << 3) | 0x01));
/* Setup GPDMA channel --------------------------------*/
/* channel 0 */
GPDMACfg.ChannelNum = 0;
/* Source memory */
GPDMACfg.SrcMemAddr = txblock;
/* Destination memory */
GPDMACfg.DstMemAddr = 0;
/* Transfer size */
GPDMACfg.TransferSize = TRANSFER_SIZE;
/* Transfer width */
GPDMACfg.TransferWidth = 0;
/* Transfer type */
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_M2P;
/* Source connection - unused */
GPDMACfg.SrcConn = 0;
/* Destination connection - I2S */
GPDMACfg.DstConn = GPDMA_CONN_I2S_Channel_0;
/* Linker List Item - unused */
GPDMACfg.DMALLI = 0;
/* Setup channel with given parameter */
GPDMA_Setup(&GPDMACfg);
// Setup GPDMA channel --------------------------------
// channel 1
GPDMACfg.ChannelNum = 1;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = rxblock;
// Transfer size
GPDMACfg.TransferSize = TRANSFER_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection - unused
GPDMACfg.SrcConn = GPDMA_CONN_I2S_Channel_1;
// Destination connection
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
/* Setup channel with given parameter */
GPDMA_Setup(&GPDMACfg);
/* Enable GPDMA channel 0*/
GPDMA_ChannelCmd(0, ENABLE);
/* Enable GPDMA channel 1 */
GPDMA_ChannelCmd(1, ENABLE);
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
//Setup DMA
I2SDMACfg.DMAIndex = I2S_DMA_1;
I2SDMACfg.depth = 4;
I2S_DMAConfig(LPC_I2S, &I2SDMACfg, I2S_TX_MODE);
I2SDMACfg.DMAIndex = I2S_DMA_2;
I2SDMACfg.depth = 8;
I2S_DMAConfig(LPC_I2S, &I2SDMACfg, I2S_RX_MODE);
//Enable DMA
I2S_DMACmd(LPC_I2S, I2S_DMA_1, I2S_TX_MODE, ENABLE);
I2S_DMACmd(LPC_I2S, I2S_DMA_2, I2S_RX_MODE, ENABLE);
}
void TIMER0_IRQHandler(void){
// xprintf("TIMER0_IRQ");
if (TIM_GetIntStatus(LPC_TIM0,TIM_MR0_INT)){
TIM_ClearIntPending(LPC_TIM0, TIM_MR0_INT);
#if 0
if(TOG[0])
// FIO_SetValue(LED_LE_PORT, LED_LE_BIT);
GPIO_SetValue(LED_4_PORT, LED_4_BIT);
else
// FIO_ClearValue(LED_LE_PORT, LED_LE_BIT);
GPIO_ClearValue(LED_4_PORT, LED_4_BIT);
TOG[0]=!TOG[0];
// TIM_ClearIntPending(LPC_TIM0, TIM_MR0_INT);
// return;
#endif
// xprintf(INFO "RIT N=%d B=%x NXT_T=%d TX=%x\n",SENDSEQ,SEND_BIT,DELAY_TIME,LED_PRECALC[0][SEND_BIT]);
//Setup new timing for next Timer
DELAY_TIME=SEQ_TIME[SENDSEQ];
SEND_BIT=SEQ_BIT[SENDSEQ];
//Retart sequence if required
SENDSEQ++;
SENDSEQ>=no_SEQ_BITS ? SENDSEQ=0 : 0;
#ifdef DMA
// xprintf("SEND_BIT:%d\n",SEND_BIT);
// xprintf("DELAY_TIME:%d\n",DELAY_TIME);
GPDMACfg.DMALLI = (uint32_t) &LinkerList[0][SEND_BIT][BufferNo];
GPDMA_Setup(&GPDMACfg);
GPDMA_ChannelCmd(0, ENABLE);
#endif
TIM_UpdateMatchValue(LPC_TIM0,0,DELAY_TIME);
FIO_SetValue(LED_OE_PORT, LED_OE_BIT);
#ifdef RxDMA
GPDMA_ChannelCmd(1, ENABLE);
uint8_t reg;
for(reg=6; 0<reg;reg--){
xprintf("%d ",reg-1);
#if 0
if(BUFFER==1)
SSP_SendData(LED_SPI_CHN, LED_PRECALC1[reg][SEND_BIT]);
else
SSP_SendData(LED_SPI_CHN, LED_PRECALC2[reg][SEND_BIT]);
#endif
//WaitForSend();//Wait if TX buffer full
//while(LED_SPI_CHN->SR & SSP_STAT_BUSY);
while(SSP_GetStatus(LED_SPI_CHN, SSP_STAT_BUSY)){
};
SSP_SendData(LED_SPI_CHN, LED_PRECALC[reg-1][SEND_BIT]);
xprintf("%4x ",(LED_PRECALC[reg-1][SEND_BIT]));
}
for(reg=12; reg>6;reg--){
xprintf("%d ",reg-1);
#if 0
if(BUFFER==1)
SSP_SendData(LED_SPI_CHN, LED_PRECALC1[reg][SEND_BIT]);
else
SSP_SendData(LED_SPI_CHN, LED_PRECALC2[reg][SEND_BIT]);
#endif
//WaitForSend();//Wait if TX buffer full
while(SSP_GetStatus(LED_SPI_CHN, SSP_STAT_BUSY)){
}
SSP_SendData(LED_SPI_CHN, LED_PRECALC[reg-1][SEND_BIT]);
// if (reg==7){
xprintf("%4x ",(LED_PRECALC[reg-1][SEND_BIT]));
// }
}
LatchIn();
#endif
/* UPDATE_COUNT+=1;
ATE_COUNT=0;
LED_UPDATE_REQUIRED=1;
}*/
}
}
