C++ (Cpp) GPIOPowIntClear Beispiele

Beispiel #1

Datei: main.c Projekt: lab11/cc2538-base

//*****************************************************************************
//
// Implementations of function that are required by usb framework.
//
//*****************************************************************************
void usbsuspHookEnteringSuspend(bool remoteWakeupAllowed) {
    if (remoteWakeupAllowed) {
        GPIOPowIntClear(BSP_KEY_SEL_BASE, BSP_KEY_SELECT);
        GPIOPowIntEnable(BSP_KEY_SEL_BASE, BSP_KEY_SELECT);
        IntPendClear(INT_GPIOA);
        IntEnable(INT_GPIOA);

        GPIOPowIntClear(BSP_KEY_DIR_BASE, BSP_KEY_DIR_ALL);
        GPIOPowIntEnable(BSP_KEY_DIR_BASE, BSP_KEY_DIR_ALL);
        IntPendClear(INT_GPIOC);
        IntEnable(INT_GPIOC);
    }
}

Beispiel #2

Datei: zcl_EnergyHarvester.c Projekt: chessami92/ceen4360-cc2538-code

void zclEnergyHarvester_Init( byte task_id ) {
  zclEnergyHarvester_TaskID = task_id;

  // This app is part of the Home Automation Profile
  zclHA_Init( &zclSampleLight_SimpleDesc );

  // Register for a test endpoint
  afRegister( &testEp );
  
  zcl_registerPlugin( ZCL_CLUSTER_ID_MS_ILLUMINANCE_MEASUREMENT,
    ZCL_CLUSTER_ID_MS_ALL,
    zclEnergyHarvester_HdlIncoming );
  
  ZDO_RegisterForZDOMsg( zclEnergyHarvester_TaskID, End_Device_Bind_rsp );
  
#if DEV_TYPE == COORDINATOR
  ZDO_RegisterForZDOMsg( zclEnergyHarvester_TaskID, Device_annce );
#else
  adc_Init();
  
  // Configure signal from off-chip timer to be wake-up signal
  GPIODirModeSet( GPIO_B_BASE, GPIO_PIN_3 , GPIO_DIR_MODE_IN );
  
  // Configure deep sleep in power mode 3, woken up by off-chip timer
  SysCtrlDeepSleepSetting();
  SysCtrlPowerModeSet( SYS_CTRL_PM_3 );
  GPIODirModeSet( GPIO_B_BASE, GPIO_PIN_4 , GPIO_DIR_MODE_IN );
  HWREG( SYS_CTRL_IWE ) = 0x02;
  GPIOPowIntTypeSet( GPIO_B_BASE, GPIO_PIN_4, GPIO_POW_RISING_EDGE );
  GPIOPowIntClear( GPIO_B_BASE, GPIO_PIN_4 );
  GPIOPowIntEnable( GPIO_B_BASE, GPIO_PIN_4 );
  
  // Done with off-chip timer acknowledge
  GPIOPinWrite( GPIO_B_BASE, GPIO_PIN_5, GPIO_PIN_5 );
#endif
}

Beispiel #3

Datei: hal_sys_ctrl.c Projekt: ndksys01/FinalProject

/**************************************************************************************************
 * @fn          SysCtrlPowIntDisableSetting
 *
 * @brief       Clear the Power Interrupt registers
 *
 * input parameters
 *
 * @param       None.
 *
 * output parameters
 *
 * None.
 *
 * @return      None.
 **************************************************************************************************
 */
void SysCtrlPowIntClear(void)
{
  GPIOPowIntClear(BSP_KEY_DIR_BASE, BSP_KEY_LEFT | BSP_KEY_RIGHT | BSP_KEY_UP |
                  BSP_KEY_DOWN);
  GPIOPowIntClear(BSP_KEY_SEL_BASE,BSP_KEY_SELECT);
}

Beispiel #4

Datei: hal_sys_ctrl.c Projekt: Daan1992/WSN-Lab

/**************************************************************************************************
 * @fn          SysCtrlPowIntDisableSetting
 *
 * @brief       Clear the Power Interrupt registers
 *
 * input parameters
 *
 * @param       None.
 *
 * output parameters
 *
 * None.
 *
 * @return      None.
 **************************************************************************************************
 */
void SysCtrlPowIntClear(void)
{

  GPIOPowIntClear(GPIO_B_BASE, GPIO_PIN_2);
}