/**
* @brief Initializes the DSI LCD.
* The ititialization is done as below:
* - DSI PLL ititialization
* - DSI ititialization
* - LTDC ititialization
* - OTM8009A LCD Display IC Driver ititialization
* @param None
* @retval LCD state
*/
static uint8_t LCD_Init(void)
{
/* Toggle Hardware Reset of the DSI LCD using
* its XRES signal (active low) */
BSP_LCD_Reset();
/* Call first MSP Initialize only in case of first initialization
* This will set IP blocks LTDC, DSI and DMA2D
* - out of reset
* - clocked
* - NVIC IRQ related to IP blocks enabled
*/
BSP_LCD_MspInit();
/* LCD clock configuration */
/* PLLSAI_VCO Input = HSE_VALUE/PLL_M = 1 Mhz */
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN = 417 Mhz */
/* PLLLCDCLK = PLLSAI_VCO Output/PLLSAIR = 417 MHz / 5 = 83.4 MHz */
/* LTDC clock frequency = PLLLCDCLK / LTDC_PLLSAI_DIVR_2 = 83.4 / 2 = 41.7 MHz */
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_LTDC;
PeriphClkInitStruct.PLLSAI.PLLSAIN = 417;
PeriphClkInitStruct.PLLSAI.PLLSAIR = 5;
PeriphClkInitStruct.PLLSAIDivR = RCC_PLLSAIDIVR_2;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
/* Base address of DSI Host/Wrapper registers to be set before calling De-Init */
hdsi_eval.Instance = DSI;
HAL_DSI_DeInit(&(hdsi_eval));
dsiPllInit.PLLNDIV = 100;
dsiPllInit.PLLIDF = DSI_PLL_IN_DIV5;
dsiPllInit.PLLODF = DSI_PLL_OUT_DIV1;
hdsi_eval.Init.NumberOfLanes = DSI_TWO_DATA_LANES;
hdsi_eval.Init.TXEscapeCkdiv = 0x4;
HAL_DSI_Init(&(hdsi_eval), &(dsiPllInit));
/* Configure the DSI for Command mode */
CmdCfg.VirtualChannelID = 0;
CmdCfg.HSPolarity = DSI_HSYNC_ACTIVE_HIGH;
CmdCfg.VSPolarity = DSI_VSYNC_ACTIVE_HIGH;
CmdCfg.DEPolarity = DSI_DATA_ENABLE_ACTIVE_HIGH;
CmdCfg.ColorCoding = DSI_RGB888;
CmdCfg.CommandSize = HACT;
CmdCfg.TearingEffectSource = DSI_TE_DSILINK;
CmdCfg.TearingEffectPolarity = DSI_TE_RISING_EDGE;
CmdCfg.VSyncPol = DSI_VSYNC_FALLING;
CmdCfg.AutomaticRefresh = DSI_AR_ENABLE;
CmdCfg.TEAcknowledgeRequest = DSI_TE_ACKNOWLEDGE_ENABLE;
HAL_DSI_ConfigAdaptedCommandMode(&hdsi_eval, &CmdCfg);
LPCmd.LPGenShortWriteNoP = DSI_LP_GSW0P_ENABLE;
LPCmd.LPGenShortWriteOneP = DSI_LP_GSW1P_ENABLE;
LPCmd.LPGenShortWriteTwoP = DSI_LP_GSW2P_ENABLE;
LPCmd.LPGenShortReadNoP = DSI_LP_GSR0P_ENABLE;
LPCmd.LPGenShortReadOneP = DSI_LP_GSR1P_ENABLE;
LPCmd.LPGenShortReadTwoP = DSI_LP_GSR2P_ENABLE;
LPCmd.LPGenLongWrite = DSI_LP_GLW_ENABLE;
LPCmd.LPDcsShortWriteNoP = DSI_LP_DSW0P_ENABLE;
LPCmd.LPDcsShortWriteOneP = DSI_LP_DSW1P_ENABLE;
LPCmd.LPDcsShortReadNoP = DSI_LP_DSR0P_ENABLE;
LPCmd.LPDcsLongWrite = DSI_LP_DLW_ENABLE;
HAL_DSI_ConfigCommand(&hdsi_eval, &LPCmd);
/* Initialize LTDC */
LTDC_Init();
/* Start DSI */
HAL_DSI_Start(&(hdsi_eval));
/* Initialize the OTM8009A LCD Display IC Driver (KoD LCD IC Driver)*/
OTM8009A_Init(OTM8009A_COLMOD_RGB888, LCD_ORIENTATION_LANDSCAPE);
/* Reconfigure the DSI for HS Command mode */
LPCmd.LPGenShortWriteNoP = DSI_LP_GSW0P_DISABLE;
LPCmd.LPGenShortWriteOneP = DSI_LP_GSW1P_DISABLE;
LPCmd.LPGenShortWriteTwoP = DSI_LP_GSW2P_DISABLE;
LPCmd.LPGenShortReadNoP = DSI_LP_GSR0P_DISABLE;
LPCmd.LPGenShortReadOneP = DSI_LP_GSR1P_DISABLE;
LPCmd.LPGenShortReadTwoP = DSI_LP_GSR2P_DISABLE;
LPCmd.LPGenLongWrite = DSI_LP_GLW_DISABLE;
LPCmd.LPDcsShortWriteNoP = DSI_LP_DSW0P_DISABLE;
LPCmd.LPDcsShortWriteOneP = DSI_LP_DSW1P_DISABLE;
LPCmd.LPDcsShortReadNoP = DSI_LP_DSR0P_DISABLE;
LPCmd.LPDcsLongWrite = DSI_LP_DLW_DISABLE;
HAL_DSI_ConfigCommand(&hdsi_eval, &LPCmd);
HAL_DSI_ConfigFlowControl(&hdsi_eval, DSI_FLOW_CONTROL_BTA);
/* Refresh the display */
HAL_DSI_Refresh(&hdsi_eval);
return LCD_OK;
}
/**
* @brief Initializes the DSI LCD.
* The ititialization is done as below:
* - DSI PLL ititialization
* - DSI ititialization
* - LTDC ititialization
* - OTM8009A LCD Display IC Driver ititialization
* @param None
* @retval LCD state
*/
static uint8_t LCD_Init(void){
GPIO_InitTypeDef GPIO_Init_Structure;
/* Toggle Hardware Reset of the DSI LCD using
* its XRES signal (active low) */
BSP_LCD_Reset();
/* Call first MSP Initialize only in case of first initialization
* This will set IP blocks LTDC, DSI and DMA2D
* - out of reset
* - clocked
* - NVIC IRQ related to IP blocks enabled
*/
BSP_LCD_MspInit();
/* LCD clock configuration */
/* PLLSAI_VCO Input = HSE_VALUE/PLL_M = 1 Mhz */
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN = 417 Mhz */
/* PLLLCDCLK = PLLSAI_VCO Output/PLLSAIR = 417 MHz / 5 = 83.4 MHz */
/* LTDC clock frequency = PLLLCDCLK / LTDC_PLLSAI_DIVR_2 = 83.4 / 2 = 41.7 MHz */
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_LTDC;
PeriphClkInitStruct.PLLSAI.PLLSAIN = 417;
PeriphClkInitStruct.PLLSAI.PLLSAIR = 5;
PeriphClkInitStruct.PLLSAIDivR = RCC_PLLSAIDIVR_2;
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
/* Base address of DSI Host/Wrapper registers to be set before calling De-Init */
hdsi_eval.Instance = DSI;
HAL_DSI_DeInit(&(hdsi_eval));
#if defined(USE_STM32469I_DISCO_REVA)
dsiPllInit.PLLNDIV = 100;
dsiPllInit.PLLIDF = DSI_PLL_IN_DIV5;
#else
dsiPllInit.PLLNDIV = 125;
dsiPllInit.PLLIDF = DSI_PLL_IN_DIV2;
#endif /* USE_STM32469I_DISCO_REVA */
dsiPllInit.PLLODF = DSI_PLL_OUT_DIV1;
hdsi_eval.Init.NumberOfLanes = DSI_TWO_DATA_LANES;
hdsi_eval.Init.TXEscapeCkdiv = 0x4;
HAL_DSI_Init(&(hdsi_eval), &(dsiPllInit));
/* Configure the DSI for Command mode */
CmdCfg.VirtualChannelID = 0;
CmdCfg.HSPolarity = DSI_HSYNC_ACTIVE_HIGH;
CmdCfg.VSPolarity = DSI_VSYNC_ACTIVE_HIGH;
CmdCfg.DEPolarity = DSI_DATA_ENABLE_ACTIVE_HIGH;
CmdCfg.ColorCoding = DSI_RGB888;
CmdCfg.CommandSize = HACT;
CmdCfg.TearingEffectSource = DSI_TE_EXTERNAL;
CmdCfg.TearingEffectPolarity = DSI_TE_RISING_EDGE;
CmdCfg.VSyncPol = DSI_VSYNC_FALLING;
CmdCfg.AutomaticRefresh = DSI_AR_DISABLE;
CmdCfg.TEAcknowledgeRequest = DSI_TE_ACKNOWLEDGE_ENABLE;
HAL_DSI_ConfigAdaptedCommandMode(&hdsi_eval, &CmdCfg);
LPCmd.LPGenShortWriteNoP = DSI_LP_GSW0P_ENABLE;
LPCmd.LPGenShortWriteOneP = DSI_LP_GSW1P_ENABLE;
LPCmd.LPGenShortWriteTwoP = DSI_LP_GSW2P_ENABLE;
LPCmd.LPGenShortReadNoP = DSI_LP_GSR0P_ENABLE;
LPCmd.LPGenShortReadOneP = DSI_LP_GSR1P_ENABLE;
LPCmd.LPGenShortReadTwoP = DSI_LP_GSR2P_ENABLE;
LPCmd.LPGenLongWrite = DSI_LP_GLW_ENABLE;
LPCmd.LPDcsShortWriteNoP = DSI_LP_DSW0P_ENABLE;
LPCmd.LPDcsShortWriteOneP = DSI_LP_DSW1P_ENABLE;
LPCmd.LPDcsShortReadNoP = DSI_LP_DSR0P_ENABLE;
LPCmd.LPDcsLongWrite = DSI_LP_DLW_ENABLE;
HAL_DSI_ConfigCommand(&hdsi_eval, &LPCmd);
/* Initialize LTDC */
LTDC_Init();
/* Start DSI */
HAL_DSI_Start(&(hdsi_eval));
/* Initialize the OTM8009A LCD Display IC Driver (KoD LCD IC Driver)
* depending on configuration set in 'hdsivideo_handle'.
*/
OTM8009A_Init(OTM8009A_COLMOD_RGB888, LCD_ORIENTATION_LANDSCAPE);
LPCmd.LPGenShortWriteNoP = DSI_LP_GSW0P_DISABLE;
LPCmd.LPGenShortWriteOneP = DSI_LP_GSW1P_DISABLE;
LPCmd.LPGenShortWriteTwoP = DSI_LP_GSW2P_DISABLE;
LPCmd.LPGenShortReadNoP = DSI_LP_GSR0P_DISABLE;
LPCmd.LPGenShortReadOneP = DSI_LP_GSR1P_DISABLE;
LPCmd.LPGenShortReadTwoP = DSI_LP_GSR2P_DISABLE;
LPCmd.LPGenLongWrite = DSI_LP_GLW_DISABLE;
LPCmd.LPDcsShortWriteNoP = DSI_LP_DSW0P_DISABLE;
LPCmd.LPDcsShortWriteOneP = DSI_LP_DSW1P_DISABLE;
LPCmd.LPDcsShortReadNoP = DSI_LP_DSR0P_DISABLE;
LPCmd.LPDcsLongWrite = DSI_LP_DLW_DISABLE;
HAL_DSI_ConfigCommand(&hdsi_eval, &LPCmd);
HAL_DSI_ConfigFlowControl(&hdsi_eval, DSI_FLOW_CONTROL_BTA);
/* Enable GPIOJ clock */
__HAL_RCC_GPIOJ_CLK_ENABLE();
/* Configure DSI_TE pin from MB1166 : Tearing effect on separated GPIO from KoD LCD */
/* that is mapped on GPIOJ2 as alternate DSI function (DSI_TE) */
/* This pin is used only when the LCD and DSI link is configured in command mode */
/* Not used in DSI Video mode. */
GPIO_Init_Structure.Pin = GPIO_PIN_2;
GPIO_Init_Structure.Mode = GPIO_MODE_AF_PP;
GPIO_Init_Structure.Pull = GPIO_NOPULL;
GPIO_Init_Structure.Speed = GPIO_SPEED_HIGH;
GPIO_Init_Structure.Alternate = GPIO_AF13_DSI;
HAL_GPIO_Init(GPIOJ, &GPIO_Init_Structure);
/* Refresh the display */
HAL_DSI_Refresh(&hdsi_eval);
return LCD_OK;
}