uint64_t sdcard_get_capacity_in_bytes(void) {
if (sd_handle.Instance == NULL) {
return 0;
}
HAL_SD_CardInfoTypedef cardinfo;
HAL_SD_Get_CardInfo(&sd_handle, &cardinfo);
return cardinfo.CardCapacity;
}
//}}}
//{{{
int8_t SD_GetCapacity (uint32_t* block_num, uint16_t* block_size) {
if (SD_present()) {
HAL_SD_CardInfoTypedef info;
HAL_SD_Get_CardInfo (&uSdHandle, &info);
*block_num = (info.CardCapacity) / 512 - 1;
*block_size = 512;
return 0;
}
return -1;
}
STATIC mp_obj_t sd_info(mp_obj_t self) {
if (sd_handle.Instance == NULL) {
return mp_const_none;
}
HAL_SD_CardInfoTypedef cardinfo;
HAL_SD_Get_CardInfo(&sd_handle, &cardinfo);
// cardinfo.SD_csd and cardinfo.SD_cid have lots of info but we don't use them
mp_obj_t tuple[3] = {
mp_obj_new_int_from_ull(cardinfo.CardCapacity),
mp_obj_new_int_from_uint(cardinfo.CardBlockSize),
mp_obj_new_int(cardinfo.CardType),
};
return mp_obj_new_tuple(3, tuple);
}
/**
* @brief Get SD information about specific SD card.
* @param CardInfo: Pointer to HAL_SD_CardInfoTypedef structure
*/
void BSP_SD_GetCardInfo(HAL_SD_CardInfoTypedef *CardInfo)
{
/* Get SD card Information */
HAL_SD_Get_CardInfo(&uSdHandle, CardInfo);
}
//}}}
//{{{
void SD_GetCardInfo (HAL_SD_CardInfoTypedef* CardInfo) {
HAL_SD_Get_CardInfo (&uSdHandle, CardInfo);
}
uint64_t sdcard_get_capacity_in_bytes(void)
{
HAL_SD_CardInfoTypedef cardinfo;
HAL_SD_Get_CardInfo(&SDHandle, &cardinfo);
return cardinfo.CardCapacity;
}
/**
* @brief Initializes the SD card device.
* @param None
* @retval SD status
*/
uint8_t BSP_SD_Init(void) {
uint8_t SD_state = MSD_OK;
/* uSD device interface configuration */
#if defined(SDIO)
uSdHandle.Instance = SDIO;
uSdHandle.Init.ClockEdge = SDIO_CLOCK_EDGE_RISING;
uSdHandle.Init.ClockBypass = SDIO_CLOCK_BYPASS_DISABLE;
uSdHandle.Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE;
uSdHandle.Init.BusWide = SDIO_BUS_WIDE_1B;
uSdHandle.Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE;
uSdHandle.Init.ClockDiv = SDIO_TRANSFER_CLK_DIV;
#elif defined(SDMMC1)
uSdHandle.Instance = SDMMC1;
uSdHandle.Init.ClockEdge = SDMMC_CLOCK_EDGE_RISING;
uSdHandle.Init.ClockBypass = SDMMC_CLOCK_BYPASS_DISABLE;
uSdHandle.Init.ClockPowerSave = SDMMC_CLOCK_POWER_SAVE_DISABLE;
uSdHandle.Init.BusWide = SDMMC_BUS_WIDE_1B;
uSdHandle.Init.HardwareFlowControl = SDMMC_HARDWARE_FLOW_CONTROL_DISABLE;
uSdHandle.Init.ClockDiv = SDMMC_TRANSFER_CLK_DIV;
#else
#error "NOT SUPPORTED!"
#endif
/* Init GPIO, DMA and NVIC */
SD_MspInit();
/* Check if the SD card is plugged in the slot */
if (BSP_SD_IsDetected() != SD_PRESENT) {
return MSD_ERROR;
}
/* HAL SD initialization */
if (HAL_SD_Init(&uSdHandle, &uSdCardInfo) != SD_OK) {
SD_state = MSD_ERROR;
}
/* Configure SD Bus width */
if (SD_state == MSD_OK) {
/* Enable wide operation */
#if defined(SDIO_BUS_WIDE_4B)
#if FATFS_SDIO_4BIT == 1
if (HAL_SD_WideBusOperation_Config(&uSdHandle, SDIO_BUS_WIDE_4B) != SD_OK) {
#else
if (HAL_SD_WideBusOperation_Config(&uSdHandle, SDIO_BUS_WIDE_1B) != SD_OK) {
#endif
#else
#if FATFS_SDIO_4BIT == 1
if (HAL_SD_WideBusOperation_Config(&uSdHandle, SDMMC_BUS_WIDE_4B) != SD_OK) {
#else
if (HAL_SD_WideBusOperation_Config(&uSdHandle, SDMMC_BUS_WIDE_1B) != SD_OK) {
#endif
#endif
SD_state = MSD_ERROR;
} else {
SD_state = MSD_OK;
}
}
return SD_state;
}
/**
* @brief Detects if SD card is correctly plugged in the memory slot or not.
* @param None
* @retval Returns if SD is detected or not
*/
uint8_t BSP_SD_IsDetected(void) {
return SDCARD_IsDetected();
}
/**
* @brief Detects if SD card is write protected
* @param None
* @retval Returns if SD is write protected or not.
*/
uint8_t BSP_SD_IsWriteProtected(void) {
return !SDCARD_IsWriteEnabled();
}
/**
* @brief Reads block(s) from a specified address in an SD card, in polling mode.
* @param pData: Pointer to the buffer that will contain the data to transmit
* @param ReadAddr: Address from where data is to be read
* @param BlockSize: SD card data block size, that should be 512
* @param NumOfBlocks: Number of SD blocks to read
* @retval SD status
*/
uint8_t BSP_SD_ReadBlocks(uint32_t *pData, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumOfBlocks) {
if (HAL_SD_ReadBlocks(&uSdHandle, pData, ReadAddr, BlockSize, NumOfBlocks) != SD_OK) {
return MSD_ERROR;
}
return MSD_OK;
}
/**
* @brief Writes block(s) to a specified address in an SD card, in polling mode.
* @param pData: Pointer to the buffer that will contain the data to transmit
* @param WriteAddr: Address from where data is to be written
* @param BlockSize: SD card data block size, that should be 512
* @param NumOfBlocks: Number of SD blocks to write
* @retval SD status
*/
uint8_t BSP_SD_WriteBlocks(uint32_t *pData, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumOfBlocks) {
if (HAL_SD_WriteBlocks(&uSdHandle, pData, WriteAddr, BlockSize, NumOfBlocks) != SD_OK) {
return MSD_ERROR;
}
return MSD_OK;
}
/**
* @brief Reads block(s) from a specified address in an SD card, in DMA mode.
* @param pData: Pointer to the buffer that will contain the data to transmit
* @param ReadAddr: Address from where data is to be read
* @param BlockSize: SD card data block size, that should be 512
* @param NumOfBlocks: Number of SD blocks to read
* @retval SD status
*/
uint8_t BSP_SD_ReadBlocks_DMA(uint32_t *pData, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumOfBlocks) {
uint8_t SD_state = MSD_OK;
/* Read block(s) in DMA transfer mode */
if (HAL_SD_ReadBlocks_DMA(&uSdHandle, pData, ReadAddr, BlockSize, NumOfBlocks) != SD_OK) {
SD_state = MSD_ERROR;
}
/* Wait until transfer is complete */
if (SD_state == MSD_OK) {
if (HAL_SD_CheckReadOperation(&uSdHandle, (uint32_t)SD_DATATIMEOUT) != SD_OK) {
SD_state = MSD_ERROR;
} else {
SD_state = MSD_OK;
}
}
return SD_state;
}
/**
* @brief Writes block(s) to a specified address in an SD card, in DMA mode.
* @param pData: Pointer to the buffer that will contain the data to transmit
* @param WriteAddr: Address from where data is to be written
* @param BlockSize: SD card data block size, that should be 512
* @param NumOfBlocks: Number of SD blocks to write
* @retval SD status
*/
uint8_t BSP_SD_WriteBlocks_DMA(uint32_t *pData, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumOfBlocks) {
uint8_t SD_state = MSD_OK;
/* Write block(s) in DMA transfer mode */
if (HAL_SD_WriteBlocks_DMA(&uSdHandle, pData, WriteAddr, BlockSize, NumOfBlocks) != SD_OK) {
SD_state = MSD_ERROR;
}
/* Wait until transfer is complete */
if (SD_state == MSD_OK) {
if(HAL_SD_CheckWriteOperation(&uSdHandle, (uint32_t)SD_DATATIMEOUT) != SD_OK) {
SD_state = MSD_ERROR;
} else {
SD_state = MSD_OK;
}
}
return SD_state;
}
/**
* @brief Erases the specified memory area of the given SD card.
* @param StartAddr: Start byte address
* @param EndAddr: End byte address
* @retval SD status
*/
uint8_t BSP_SD_Erase(uint64_t StartAddr, uint64_t EndAddr) {
if (HAL_SD_Erase(&uSdHandle, StartAddr, EndAddr) != SD_OK) {
return MSD_ERROR;
}
return MSD_OK;
}
/**
* @brief Initializes the SD MSP.
* @param None
* @retval None
*/
static void SD_MspInit(void) {
static DMA_HandleTypeDef dmaRxHandle;
static DMA_HandleTypeDef dmaTxHandle;
SD_HandleTypeDef *hsd = &uSdHandle;
uint16_t gpio_af;
/* Get GPIO alternate function */
#if defined(GPIO_AF12_SDIO)
gpio_af = GPIO_AF12_SDIO;
#endif
#if defined(GPIO_AF12_SDMMC1)
gpio_af = GPIO_AF12_SDMMC1;
#endif
/* Enable SDIO clock */
__HAL_RCC_SDIO_CLK_ENABLE();
/* Enable DMA2 clocks */
__DMAx_TxRx_CLK_ENABLE();
/* Detect pin, write protect pin */
#if FATFS_USE_DETECT_PIN > 0
TM_GPIO_Init(FATFS_DETECT_PORT, FATFS_DETECT_PIN, TM_GPIO_Mode_IN, TM_GPIO_OType_PP, TM_GPIO_PuPd_UP, TM_GPIO_Speed_Low);
#endif
#if FATFS_USE_WRITEPROTECT_PIN > 0
TM_GPIO_Init(FATFS_WRITEPROTECT_PORT, FATFS_WRITEPROTECT_PIN, TM_GPIO_Mode_IN, TM_GPIO_OType_PP, TM_GPIO_PuPd_UP, TM_GPIO_Speed_Low);
#endif
/* SDIO/SDMMC pins */
#if FATFS_SDIO_4BIT == 1
TM_GPIO_InitAlternate(GPIOC, GPIO_PIN_8 | GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12, TM_GPIO_OType_PP, TM_GPIO_PuPd_UP, TM_GPIO_Speed_Fast, gpio_af);
#else
TM_GPIO_InitAlternate(GPIOC, GPIO_PIN_8 | GPIO_PIN_12, TM_GPIO_OType_PP, TM_GPIO_PuPd_UP, TM_GPIO_Speed_Fast, gpio_af);
#endif
TM_GPIO_InitAlternate(GPIOD, GPIO_PIN_2, TM_GPIO_OType_PP, TM_GPIO_PuPd_UP, TM_GPIO_Speed_Fast, gpio_af);
/* NVIC configuration for SDIO interrupts */
HAL_NVIC_SetPriority(SDIO_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(SDIO_IRQn);
/* Configure DMA Rx parameters */
dmaRxHandle.Init.Channel = SD_DMAx_Rx_CHANNEL;
dmaRxHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
dmaRxHandle.Init.PeriphInc = DMA_PINC_DISABLE;
dmaRxHandle.Init.MemInc = DMA_MINC_ENABLE;
dmaRxHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
dmaRxHandle.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
dmaRxHandle.Init.Mode = DMA_PFCTRL;
dmaRxHandle.Init.Priority = DMA_PRIORITY_VERY_HIGH;
dmaRxHandle.Init.FIFOMode = DMA_FIFOMODE_ENABLE;
dmaRxHandle.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL;
dmaRxHandle.Init.MemBurst = DMA_MBURST_INC4;
dmaRxHandle.Init.PeriphBurst = DMA_PBURST_INC4;
dmaRxHandle.Instance = SD_DMAx_Rx_STREAM;
/* Associate the DMA handle */
__HAL_LINKDMA(hsd, hdmarx, dmaRxHandle);
/* Deinitialize the stream for new transfer */
HAL_DMA_DeInit(&dmaRxHandle);
/* Configure the DMA stream */
HAL_DMA_Init(&dmaRxHandle);
/* Configure DMA Tx parameters */
dmaTxHandle.Init.Channel = SD_DMAx_Tx_CHANNEL;
dmaTxHandle.Init.Direction = DMA_MEMORY_TO_PERIPH;
dmaTxHandle.Init.PeriphInc = DMA_PINC_DISABLE;
dmaTxHandle.Init.MemInc = DMA_MINC_ENABLE;
dmaTxHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
dmaTxHandle.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
dmaTxHandle.Init.Mode = DMA_PFCTRL;
dmaTxHandle.Init.Priority = DMA_PRIORITY_VERY_HIGH;
dmaTxHandle.Init.FIFOMode = DMA_FIFOMODE_ENABLE;
dmaTxHandle.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL;
dmaTxHandle.Init.MemBurst = DMA_MBURST_INC4;
dmaTxHandle.Init.PeriphBurst = DMA_PBURST_INC4;
dmaTxHandle.Instance = SD_DMAx_Tx_STREAM;
/* Associate the DMA handle */
__HAL_LINKDMA(hsd, hdmatx, dmaTxHandle);
/* Deinitialize the stream for new transfer */
HAL_DMA_DeInit(&dmaTxHandle);
/* Configure the DMA stream */
HAL_DMA_Init(&dmaTxHandle);
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(SD_DMAx_Rx_IRQn, 6, 0);
HAL_NVIC_EnableIRQ(SD_DMAx_Rx_IRQn);
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(SD_DMAx_Tx_IRQn, 6, 0);
HAL_NVIC_EnableIRQ(SD_DMAx_Tx_IRQn);
}
/**
* @brief Get SD information about specific SD card.
* @param CardInfo: Pointer to HAL_SD_CardInfoTypedef structure
* @retval None
*/
void BSP_SD_GetCardInfo(HAL_SD_CardInfoTypedef *CardInfo) {
/* Get SD card Information */
HAL_SD_Get_CardInfo(&uSdHandle, CardInfo);
}