static inline void bus_reset_if_active(struct i2c_pnx_algo_data *alg_data)
{
u32 stat;
if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_active) {
dev_err(&alg_data->adapter.dev,
"%s: Bus is still active after xfer. Reset it...\n",
alg_data->adapter.name);
iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_reset,
I2C_REG_CTL(alg_data));
wait_reset(alg_data);
} else if (!(stat & mstatus_rfe) || !(stat & mstatus_tfe)) {
/* If there is data in the fifo's after transfer,
* flush fifo's by reset.
*/
iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_reset,
I2C_REG_CTL(alg_data));
wait_reset(alg_data);
} else if (stat & mstatus_nai) {
iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_reset,
I2C_REG_CTL(alg_data));
wait_reset(alg_data);
}
}
static int i2c_pnx_probe(struct platform_device *pdev)
{
unsigned long tmp;
int ret = 0;
struct i2c_pnx_algo_data *alg_data;
unsigned long freq;
struct resource *res;
u32 speed = I2C_PNX_SPEED_KHZ_DEFAULT * 1000;
alg_data = devm_kzalloc(&pdev->dev, sizeof(*alg_data), GFP_KERNEL);
if (!alg_data)
return -ENOMEM;
platform_set_drvdata(pdev, alg_data);
alg_data->adapter.dev.parent = &pdev->dev;
alg_data->adapter.algo = &pnx_algorithm;
alg_data->adapter.algo_data = alg_data;
alg_data->adapter.nr = pdev->id;
alg_data->timeout = I2C_PNX_TIMEOUT_DEFAULT;
#ifdef CONFIG_OF
alg_data->adapter.dev.of_node = of_node_get(pdev->dev.of_node);
if (pdev->dev.of_node) {
of_property_read_u32(pdev->dev.of_node, "clock-frequency",
&speed);
/*
* At this point, it is planned to add an OF timeout property.
* As soon as there is a consensus about how to call and handle
* this, sth. like the following can be put here:
*
* of_property_read_u32(pdev->dev.of_node, "timeout",
* &alg_data->timeout);
*/
}
#endif
alg_data->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(alg_data->clk))
return PTR_ERR(alg_data->clk);
init_timer(&alg_data->mif.timer);
alg_data->mif.timer.function = i2c_pnx_timeout;
alg_data->mif.timer.data = (unsigned long)alg_data;
snprintf(alg_data->adapter.name, sizeof(alg_data->adapter.name),
"%s", pdev->name);
/* Register I/O resource */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
alg_data->ioaddr = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(alg_data->ioaddr))
return PTR_ERR(alg_data->ioaddr);
ret = clk_prepare_enable(alg_data->clk);
if (ret)
return ret;
freq = clk_get_rate(alg_data->clk);
/*
* Clock Divisor High This value is the number of system clocks
* the serial clock (SCL) will be high.
* For example, if the system clock period is 50 ns and the maximum
* desired serial period is 10000 ns (100 kHz), then CLKHI would be
* set to 0.5*(f_sys/f_i2c)-2=0.5*(20e6/100e3)-2=98. The actual value
* programmed into CLKHI will vary from this slightly due to
* variations in the output pad's rise and fall times as well as
* the deglitching filter length.
*/
tmp = (freq / speed) / 2 - 2;
if (tmp > 0x3FF)
tmp = 0x3FF;
iowrite32(tmp, I2C_REG_CKH(alg_data));
iowrite32(tmp, I2C_REG_CKL(alg_data));
iowrite32(mcntrl_reset, I2C_REG_CTL(alg_data));
if (wait_reset(alg_data)) {
ret = -ENODEV;
goto out_clock;
}
init_completion(&alg_data->mif.complete);
alg_data->irq = platform_get_irq(pdev, 0);
if (alg_data->irq < 0) {
dev_err(&pdev->dev, "Failed to get IRQ from platform resource\n");
ret = alg_data->irq;
goto out_clock;
}
ret = devm_request_irq(&pdev->dev, alg_data->irq, i2c_pnx_interrupt,
0, pdev->name, alg_data);
if (ret)
goto out_clock;
/* Register this adapter with the I2C subsystem */
ret = i2c_add_numbered_adapter(&alg_data->adapter);
if (ret < 0) {
dev_err(&pdev->dev, "I2C: Failed to add bus\n");
goto out_clock;
}
dev_dbg(&pdev->dev, "%s: Master at %#8x, irq %d.\n",
alg_data->adapter.name, res->start, alg_data->irq);
return 0;
out_clock:
clk_disable_unprepare(alg_data->clk);
return ret;
}
/**
* i2c_pnx_xfer - generic transfer entry point
* @adap: pointer to I2C adapter structure
* @msgs: array of messages
* @num: number of messages
*
* Initiates the transfer
*/
static int
i2c_pnx_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
struct i2c_msg *pmsg;
int rc = 0, completed = 0, i;
struct i2c_pnx_algo_data *alg_data = adap->algo_data;
u32 stat = ioread32(I2C_REG_STS(alg_data));
dev_dbg(&alg_data->adapter.dev,
"%s(): entering: %d messages, stat = %04x.\n",
__func__, num, ioread32(I2C_REG_STS(alg_data)));
bus_reset_if_active(alg_data);
/* Process transactions in a loop. */
for (i = 0; rc >= 0 && i < num; i++) {
u8 addr;
pmsg = &msgs[i];
addr = pmsg->addr;
if (pmsg->flags & I2C_M_TEN) {
dev_err(&alg_data->adapter.dev,
"%s: 10 bits addr not supported!\n",
alg_data->adapter.name);
rc = -EINVAL;
break;
}
alg_data->mif.buf = pmsg->buf;
alg_data->mif.len = pmsg->len;
alg_data->mif.order = pmsg->len;
alg_data->mif.mode = (pmsg->flags & I2C_M_RD) ?
I2C_SMBUS_READ : I2C_SMBUS_WRITE;
alg_data->mif.ret = 0;
alg_data->last = (i == num - 1);
dev_dbg(&alg_data->adapter.dev, "%s(): mode %d, %d bytes\n",
__func__, alg_data->mif.mode, alg_data->mif.len);
i2c_pnx_arm_timer(alg_data);
/* initialize the completion var */
init_completion(&alg_data->mif.complete);
/* Enable master interrupt */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) | mcntrl_afie |
mcntrl_naie | mcntrl_drmie,
I2C_REG_CTL(alg_data));
/* Put start-code and slave-address on the bus. */
rc = i2c_pnx_start(addr, alg_data);
if (rc < 0)
break;
/* Wait for completion */
wait_for_completion(&alg_data->mif.complete);
if (!(rc = alg_data->mif.ret))
completed++;
dev_dbg(&alg_data->adapter.dev,
"%s(): Complete, return code = %d.\n",
__func__, rc);
/* Clear TDI and AFI bits in case they are set. */
if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_tdi) {
dev_dbg(&alg_data->adapter.dev,
"%s: TDI still set... clearing now.\n",
alg_data->adapter.name);
iowrite32(stat, I2C_REG_STS(alg_data));
}
if ((stat = ioread32(I2C_REG_STS(alg_data))) & mstatus_afi) {
dev_dbg(&alg_data->adapter.dev,
"%s: AFI still set... clearing now.\n",
alg_data->adapter.name);
iowrite32(stat, I2C_REG_STS(alg_data));
}
}
bus_reset_if_active(alg_data);
/* Cleanup to be sure... */
alg_data->mif.buf = NULL;
alg_data->mif.len = 0;
alg_data->mif.order = 0;
dev_dbg(&alg_data->adapter.dev, "%s(): exiting, stat = %x\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
if (completed != num)
return ((rc < 0) ? rc : -EREMOTEIO);
return num;
}
static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id)
{
struct i2c_pnx_algo_data *alg_data = dev_id;
u32 stat, ctl;
dev_dbg(&alg_data->adapter.dev,
"%s(): mstat = %x mctrl = %x, mode = %d\n",
__func__,
ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)),
alg_data->mif.mode);
stat = ioread32(I2C_REG_STS(alg_data));
/* let's see what kind of event this is */
if (stat & mstatus_afi) {
/* We lost arbitration in the midst of a transfer */
alg_data->mif.ret = -EIO;
/* Disable master interrupts. */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* Stop timer, to prevent timeout. */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
} else if (stat & mstatus_nai) {
/* Slave did not acknowledge, generate a STOP */
dev_dbg(&alg_data->adapter.dev,
"%s(): Slave did not acknowledge, generating a STOP.\n",
__func__);
i2c_pnx_stop(alg_data);
/* Disable master interrupts. */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* Our return value. */
alg_data->mif.ret = -EIO;
/* Stop timer, to prevent timeout. */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
} else {
/*
* Two options:
* - Master Tx needs data.
* - There is data in the Rx-fifo
* The latter is only the case if we have requested for data,
* via a dummy write. (See 'i2c_pnx_master_rcv'.)
* We therefore check, as a sanity check, whether that interrupt
* has been enabled.
*/
if ((stat & mstatus_drmi) || !(stat & mstatus_rfe)) {
if (alg_data->mif.mode == I2C_SMBUS_WRITE) {
i2c_pnx_master_xmit(alg_data);
} else if (alg_data->mif.mode == I2C_SMBUS_READ) {
i2c_pnx_master_rcv(alg_data);
}
}
}
/* Clear TDI and AFI bits */
stat = ioread32(I2C_REG_STS(alg_data));
iowrite32(stat | mstatus_tdi | mstatus_afi, I2C_REG_STS(alg_data));
dev_dbg(&alg_data->adapter.dev,
"%s(): exiting, stat = %x ctrl = %x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)));
return IRQ_HANDLED;
}
/**
* i2c_pnx_master_rcv - receive data from slave
* @adap: pointer to I2C adapter structure
*
* Reads one byte data from the slave
*/
static int i2c_pnx_master_rcv(struct i2c_pnx_algo_data *alg_data)
{
unsigned int val = 0;
u32 ctl = 0;
dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
/* Check, whether there is already data,
* or we didn't 'ask' for it yet.
*/
if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) {
/* 'Asking' is done asynchronously, e.g. dummy TX of several
* bytes is done before the first actual RX arrives in FIFO.
* Therefore, ordered bytes (via TX) are counted separately.
*/
if (alg_data->mif.order) {
dev_dbg(&alg_data->adapter.dev,
"%s(): Write dummy data to fill Rx-fifo...\n",
__func__);
if (alg_data->mif.order == 1) {
/* Last byte, do not acknowledge next rcv. */
val |= stop_bit;
/*
* Enable interrupt RFDAIE (data in Rx fifo),
* and disable DRMIE (need data for Tx)
*/
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl |= mcntrl_rffie | mcntrl_daie;
ctl &= ~mcntrl_drmie;
iowrite32(ctl, I2C_REG_CTL(alg_data));
}
/*
* Now we'll 'ask' for data:
* For each byte we want to receive, we must
* write a (dummy) byte to the Tx-FIFO.
*/
iowrite32(val, I2C_REG_TX(alg_data));
alg_data->mif.order--;
}
return 0;
}
/* Handle data. */
if (alg_data->mif.len > 0) {
val = ioread32(I2C_REG_RX(alg_data));
*alg_data->mif.buf++ = (u8) (val & 0xff);
dev_dbg(&alg_data->adapter.dev, "%s(): rcv 0x%x [%d]\n",
__func__, val, alg_data->mif.len);
alg_data->mif.len--;
if (alg_data->mif.len == 0) {
if (alg_data->last)
/* Wait until the STOP is seen. */
if (wait_timeout(alg_data))
dev_err(&alg_data->adapter.dev,
"The bus is still active after timeout\n");
/* Disable master interrupts */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie | mcntrl_daie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* Kill timer. */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
}
}
dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
return 0;
}
/**
* i2c_pnx_master_xmit - transmit data to slave
* @adap: pointer to I2C adapter structure
*
* Sends one byte of data to the slave
*/
static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data)
{
u32 val;
dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
if (alg_data->mif.len > 0) {
/* We still have something to talk about... */
val = *alg_data->mif.buf++;
if (alg_data->mif.len == 1)
val |= stop_bit;
alg_data->mif.len--;
iowrite32(val, I2C_REG_TX(alg_data));
dev_dbg(&alg_data->adapter.dev, "%s(): xmit %#x [%d]\n",
__func__, val, alg_data->mif.len + 1);
if (alg_data->mif.len == 0) {
if (alg_data->last) {
/* Wait until the STOP is seen. */
if (wait_timeout(alg_data))
dev_err(&alg_data->adapter.dev,
"The bus is still active after timeout\n");
}
/* Disable master interrupts */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) &
~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
I2C_REG_CTL(alg_data));
del_timer_sync(&alg_data->mif.timer);
dev_dbg(&alg_data->adapter.dev,
"%s(): Waking up xfer routine.\n",
__func__);
complete(&alg_data->mif.complete);
}
} else if (alg_data->mif.len == 0) {
/* zero-sized transfer */
i2c_pnx_stop(alg_data);
/* Disable master interrupts. */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) &
~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
I2C_REG_CTL(alg_data));
/* Stop timer. */
del_timer_sync(&alg_data->mif.timer);
dev_dbg(&alg_data->adapter.dev,
"%s(): Waking up xfer routine after zero-xfer.\n",
__func__);
complete(&alg_data->mif.complete);
}
dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
return 0;
}
static int __devinit i2c_pnx_probe(struct platform_device *pdev)
{
unsigned long tmp;
int ret = 0;
struct i2c_pnx_algo_data *alg_data;
int freq_mhz;
struct i2c_pnx_data *i2c_pnx = pdev->dev.platform_data;
if (!i2c_pnx || !i2c_pnx->adapter) {
dev_err(&pdev->dev, "%s: no platform data supplied\n",
__func__);
ret = -EINVAL;
goto out;
}
platform_set_drvdata(pdev, i2c_pnx);
if (i2c_pnx->calculate_input_freq)
freq_mhz = i2c_pnx->calculate_input_freq(pdev);
else {
freq_mhz = PNX_DEFAULT_FREQ;
dev_info(&pdev->dev, "Setting bus frequency to default value: "
"%d MHz\n", freq_mhz);
}
i2c_pnx->adapter->algo = &pnx_algorithm;
alg_data = i2c_pnx->adapter->algo_data;
init_timer(&alg_data->mif.timer);
alg_data->mif.timer.function = i2c_pnx_timeout;
alg_data->mif.timer.data = (unsigned long)i2c_pnx->adapter;
/* Register I/O resource */
if (!request_mem_region(alg_data->base, I2C_PNX_REGION_SIZE,
pdev->name)) {
dev_err(&pdev->dev,
"I/O region 0x%08x for I2C already in use.\n",
alg_data->base);
ret = -ENODEV;
goto out_drvdata;
}
if (!(alg_data->ioaddr =
(u32)ioremap(alg_data->base, I2C_PNX_REGION_SIZE))) {
dev_err(&pdev->dev, "Couldn't ioremap I2C I/O region\n");
ret = -ENOMEM;
goto out_release;
}
i2c_pnx->set_clock_run(pdev);
/*
* Clock Divisor High This value is the number of system clocks
* the serial clock (SCL) will be high.
* For example, if the system clock period is 50 ns and the maximum
* desired serial period is 10000 ns (100 kHz), then CLKHI would be
* set to 0.5*(f_sys/f_i2c)-2=0.5*(20e6/100e3)-2=98. The actual value
* programmed into CLKHI will vary from this slightly due to
* variations in the output pad's rise and fall times as well as
* the deglitching filter length.
*/
tmp = ((freq_mhz * 1000) / I2C_PNX_SPEED_KHZ) / 2 - 2;
iowrite32(tmp, I2C_REG_CKH(alg_data));
iowrite32(tmp, I2C_REG_CKL(alg_data));
iowrite32(mcntrl_reset, I2C_REG_CTL(alg_data));
if (wait_reset(I2C_PNX_TIMEOUT, alg_data)) {
ret = -ENODEV;
goto out_unmap;
}
init_completion(&alg_data->mif.complete);
ret = request_irq(alg_data->irq, i2c_pnx_interrupt,
0, pdev->name, i2c_pnx->adapter);
if (ret)
goto out_clock;
/* Register this adapter with the I2C subsystem */
i2c_pnx->adapter->dev.parent = &pdev->dev;
ret = i2c_add_adapter(i2c_pnx->adapter);
if (ret < 0) {
dev_err(&pdev->dev, "I2C: Failed to add bus\n");
goto out_irq;
}
dev_dbg(&pdev->dev, "%s: Master at %#8x, irq %d.\n",
i2c_pnx->adapter->name, alg_data->base, alg_data->irq);
return 0;
out_irq:
free_irq(alg_data->irq, alg_data);
out_clock:
i2c_pnx->set_clock_stop(pdev);
out_unmap:
iounmap((void *)alg_data->ioaddr);
out_release:
release_mem_region(alg_data->base, I2C_PNX_REGION_SIZE);
out_drvdata:
platform_set_drvdata(pdev, NULL);
out:
return ret;
}
/**
* i2c_pnx_master_rcv - receive data from slave
* @adap: pointer to I2C adapter structure
*
* Reads one byte data from the slave
*/
static int i2c_pnx_master_rcv(struct i2c_adapter *adap)
{
struct i2c_pnx_algo_data *alg_data = adap->algo_data;
unsigned int val = 0;
u32 ctl = 0;
dev_dbg(&adap->dev, "%s(): entering: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
/* Check, whether there is already data,
* or we didn't 'ask' for it yet.
*/
if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) {
dev_dbg(&adap->dev, "%s(): Write dummy data to fill "
"Rx-fifo...\n", __func__);
if (alg_data->mif.len == 1) {
/* Last byte, do not acknowledge next rcv. */
val |= stop_bit;
if (!alg_data->last)
val |= start_bit;
/*
* Enable interrupt RFDAIE (data in Rx fifo),
* and disable DRMIE (need data for Tx)
*/
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl |= mcntrl_rffie | mcntrl_daie;
ctl &= ~mcntrl_drmie;
iowrite32(ctl, I2C_REG_CTL(alg_data));
}
/*
* Now we'll 'ask' for data:
* For each byte we want to receive, we must
* write a (dummy) byte to the Tx-FIFO.
*/
iowrite32(val, I2C_REG_TX(alg_data));
return 0;
}
/* Handle data. */
if (alg_data->mif.len > 0) {
val = ioread32(I2C_REG_RX(alg_data));
*alg_data->mif.buf++ = (u8) (val & 0xff);
dev_dbg(&adap->dev, "%s(): rcv 0x%x [%d]\n", __func__, val,
alg_data->mif.len);
alg_data->mif.len--;
if (alg_data->mif.len == 0) {
if (alg_data->last)
/* Wait until the STOP is seen. */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data))
dev_err(&adap->dev, "The bus is still "
"active after timeout\n");
/* Disable master interrupts */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie | mcntrl_daie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* Kill timer. */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
}
}
dev_dbg(&adap->dev, "%s(): exiting: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
return 0;
}
static int __devinit i2c_pnx_probe(struct platform_device *pdev)
{
unsigned long tmp;
int ret = 0;
struct i2c_pnx_algo_data *alg_data;
unsigned long freq;
struct i2c_pnx_data *i2c_pnx = pdev->dev.platform_data;
if (!i2c_pnx || !i2c_pnx->name) {
dev_err(&pdev->dev, "%s: no platform data supplied\n",
__func__);
ret = -EINVAL;
goto out;
}
alg_data = kzalloc(sizeof(*alg_data), GFP_KERNEL);
if (!alg_data) {
ret = -ENOMEM;
goto err_kzalloc;
}
platform_set_drvdata(pdev, alg_data);
strlcpy(alg_data->adapter.name, i2c_pnx->name,
sizeof(alg_data->adapter.name));
alg_data->adapter.dev.parent = &pdev->dev;
alg_data->adapter.algo = &pnx_algorithm;
alg_data->adapter.algo_data = alg_data;
alg_data->adapter.nr = pdev->id;
alg_data->i2c_pnx = i2c_pnx;
alg_data->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(alg_data->clk)) {
ret = PTR_ERR(alg_data->clk);
goto out_drvdata;
}
init_timer(&alg_data->mif.timer);
alg_data->mif.timer.function = i2c_pnx_timeout;
alg_data->mif.timer.data = (unsigned long)alg_data;
/* Register I/O resource */
if (!request_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE,
pdev->name)) {
dev_err(&pdev->dev,
"I/O region 0x%08x for I2C already in use.\n",
i2c_pnx->base);
ret = -ENODEV;
goto out_clkget;
}
alg_data->ioaddr = ioremap(i2c_pnx->base, I2C_PNX_REGION_SIZE);
if (!alg_data->ioaddr) {
dev_err(&pdev->dev, "Couldn't ioremap I2C I/O region\n");
ret = -ENOMEM;
goto out_release;
}
ret = clk_enable(alg_data->clk);
if (ret)
goto out_unmap;
freq = clk_get_rate(alg_data->clk);
/*
* Clock Divisor High This value is the number of system clocks
* the serial clock (SCL) will be high.
* For example, if the system clock period is 50 ns and the maximum
* desired serial period is 10000 ns (100 kHz), then CLKHI would be
* set to 0.5*(f_sys/f_i2c)-2=0.5*(20e6/100e3)-2=98. The actual value
* programmed into CLKHI will vary from this slightly due to
* variations in the output pad's rise and fall times as well as
* the deglitching filter length.
*/
tmp = ((freq / 1000) / I2C_PNX_SPEED_KHZ) / 2 - 2;
iowrite32(tmp, I2C_REG_CKH(alg_data));
iowrite32(tmp, I2C_REG_CKL(alg_data));
iowrite32(mcntrl_reset, I2C_REG_CTL(alg_data));
if (wait_reset(I2C_PNX_TIMEOUT, alg_data)) {
ret = -ENODEV;
goto out_clock;
}
init_completion(&alg_data->mif.complete);
ret = request_irq(i2c_pnx->irq, i2c_pnx_interrupt,
0, pdev->name, alg_data);
if (ret)
goto out_clock;
/* Register this adapter with the I2C subsystem */
ret = i2c_add_numbered_adapter(&alg_data->adapter);
if (ret < 0) {
dev_err(&pdev->dev, "I2C: Failed to add bus\n");
goto out_irq;
}
dev_dbg(&pdev->dev, "%s: Master at %#8x, irq %d.\n",
alg_data->adapter.name, i2c_pnx->base, i2c_pnx->irq);
return 0;
out_irq:
free_irq(i2c_pnx->irq, alg_data);
out_clock:
clk_disable(alg_data->clk);
out_unmap:
iounmap(alg_data->ioaddr);
out_release:
release_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE);
out_clkget:
clk_put(alg_data->clk);
out_drvdata:
kfree(alg_data);
err_kzalloc:
platform_set_drvdata(pdev, NULL);
out:
return ret;
}
static int __devinit i2c_pnx_probe(struct platform_device *pdev)
{
unsigned long tmp;
int ret = 0;
struct i2c_pnx_algo_data *alg_data;
unsigned long freq;
struct i2c_pnx_data *i2c_pnx = pdev->dev.platform_data;
if (!i2c_pnx || !i2c_pnx->name) {
dev_err(&pdev->dev, "%s: no platform data supplied\n",
__func__);
ret = -EINVAL;
goto out;
}
alg_data = kzalloc(sizeof(*alg_data), GFP_KERNEL);
if (!alg_data) {
ret = -ENOMEM;
goto err_kzalloc;
}
platform_set_drvdata(pdev, alg_data);
strlcpy(alg_data->adapter.name, i2c_pnx->name,
sizeof(alg_data->adapter.name));
alg_data->adapter.dev.parent = &pdev->dev;
alg_data->adapter.algo = &pnx_algorithm;
alg_data->adapter.algo_data = alg_data;
alg_data->adapter.nr = pdev->id;
alg_data->i2c_pnx = i2c_pnx;
alg_data->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(alg_data->clk)) {
ret = PTR_ERR(alg_data->clk);
goto out_drvdata;
}
init_timer(&alg_data->mif.timer);
alg_data->mif.timer.function = i2c_pnx_timeout;
alg_data->mif.timer.data = (unsigned long)alg_data;
/* */
if (!request_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE,
pdev->name)) {
dev_err(&pdev->dev,
"I/O region 0x%08x for I2C already in use.\n",
i2c_pnx->base);
ret = -ENODEV;
goto out_clkget;
}
alg_data->ioaddr = ioremap(i2c_pnx->base, I2C_PNX_REGION_SIZE);
if (!alg_data->ioaddr) {
dev_err(&pdev->dev, "Couldn't ioremap I2C I/O region\n");
ret = -ENOMEM;
goto out_release;
}
ret = clk_enable(alg_data->clk);
if (ret)
goto out_unmap;
freq = clk_get_rate(alg_data->clk);
/*
*/
tmp = ((freq / 1000) / I2C_PNX_SPEED_KHZ) / 2 - 2;
if (tmp > 0x3FF)
tmp = 0x3FF;
iowrite32(tmp, I2C_REG_CKH(alg_data));
iowrite32(tmp, I2C_REG_CKL(alg_data));
iowrite32(mcntrl_reset, I2C_REG_CTL(alg_data));
if (wait_reset(I2C_PNX_TIMEOUT, alg_data)) {
ret = -ENODEV;
goto out_clock;
}
init_completion(&alg_data->mif.complete);
ret = request_irq(i2c_pnx->irq, i2c_pnx_interrupt,
0, pdev->name, alg_data);
if (ret)
goto out_clock;
/* */
ret = i2c_add_numbered_adapter(&alg_data->adapter);
if (ret < 0) {
dev_err(&pdev->dev, "I2C: Failed to add bus\n");
goto out_irq;
}
dev_dbg(&pdev->dev, "%s: Master at %#8x, irq %d.\n",
alg_data->adapter.name, i2c_pnx->base, i2c_pnx->irq);
return 0;
out_irq:
free_irq(i2c_pnx->irq, alg_data);
out_clock:
clk_disable(alg_data->clk);
out_unmap:
iounmap(alg_data->ioaddr);
out_release:
release_mem_region(i2c_pnx->base, I2C_PNX_REGION_SIZE);
out_clkget:
clk_put(alg_data->clk);
out_drvdata:
kfree(alg_data);
err_kzalloc:
platform_set_drvdata(pdev, NULL);
out:
return ret;
}
static irqreturn_t i2c_pnx_interrupt(int irq, void *dev_id)
{
struct i2c_pnx_algo_data *alg_data = dev_id;
u32 stat, ctl;
dev_dbg(&alg_data->adapter.dev,
"%s(): mstat = %x mctrl = %x, mode = %d\n",
__func__,
ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)),
alg_data->mif.mode);
stat = ioread32(I2C_REG_STS(alg_data));
/* */
if (stat & mstatus_afi) {
/* */
alg_data->mif.ret = -EIO;
/* */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
} else if (stat & mstatus_nai) {
/* */
dev_dbg(&alg_data->adapter.dev,
"%s(): Slave did not acknowledge, generating a STOP.\n",
__func__);
i2c_pnx_stop(alg_data);
/* */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* */
alg_data->mif.ret = -EIO;
/* */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
} else {
/*
*/
if ((stat & mstatus_drmi) || !(stat & mstatus_rfe)) {
if (alg_data->mif.mode == I2C_SMBUS_WRITE) {
i2c_pnx_master_xmit(alg_data);
} else if (alg_data->mif.mode == I2C_SMBUS_READ) {
i2c_pnx_master_rcv(alg_data);
}
}
}
/* */
stat = ioread32(I2C_REG_STS(alg_data));
iowrite32(stat | mstatus_tdi | mstatus_afi, I2C_REG_STS(alg_data));
dev_dbg(&alg_data->adapter.dev,
"%s(): exiting, stat = %x ctrl = %x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)),
ioread32(I2C_REG_CTL(alg_data)));
return IRQ_HANDLED;
}
static int i2c_pnx_master_rcv(struct i2c_pnx_algo_data *alg_data)
{
unsigned int val = 0;
u32 ctl = 0;
dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
/*
*/
if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) {
dev_dbg(&alg_data->adapter.dev,
"%s(): Write dummy data to fill Rx-fifo...\n",
__func__);
if (alg_data->mif.len == 1) {
/* */
val |= stop_bit;
/*
*/
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl |= mcntrl_rffie | mcntrl_daie;
ctl &= ~mcntrl_drmie;
iowrite32(ctl, I2C_REG_CTL(alg_data));
}
/*
*/
iowrite32(val, I2C_REG_TX(alg_data));
return 0;
}
/* */
if (alg_data->mif.len > 0) {
val = ioread32(I2C_REG_RX(alg_data));
*alg_data->mif.buf++ = (u8) (val & 0xff);
dev_dbg(&alg_data->adapter.dev, "%s(): rcv 0x%x [%d]\n",
__func__, val, alg_data->mif.len);
alg_data->mif.len--;
if (alg_data->mif.len == 0) {
if (alg_data->last)
/* */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data))
dev_err(&alg_data->adapter.dev,
"The bus is still active after timeout\n");
/* */
ctl = ioread32(I2C_REG_CTL(alg_data));
ctl &= ~(mcntrl_afie | mcntrl_naie | mcntrl_rffie |
mcntrl_drmie | mcntrl_daie);
iowrite32(ctl, I2C_REG_CTL(alg_data));
/* */
del_timer_sync(&alg_data->mif.timer);
complete(&alg_data->mif.complete);
}
}
dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
return 0;
}
static int i2c_pnx_master_xmit(struct i2c_pnx_algo_data *alg_data)
{
u32 val;
dev_dbg(&alg_data->adapter.dev, "%s(): entering: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
if (alg_data->mif.len > 0) {
/* */
val = *alg_data->mif.buf++;
if (alg_data->mif.len == 1)
val |= stop_bit;
alg_data->mif.len--;
iowrite32(val, I2C_REG_TX(alg_data));
dev_dbg(&alg_data->adapter.dev, "%s(): xmit %#x [%d]\n",
__func__, val, alg_data->mif.len + 1);
if (alg_data->mif.len == 0) {
if (alg_data->last) {
/* */
if (wait_timeout(I2C_PNX_TIMEOUT, alg_data))
dev_err(&alg_data->adapter.dev,
"The bus is still active after timeout\n");
}
/* */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) &
~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
I2C_REG_CTL(alg_data));
del_timer_sync(&alg_data->mif.timer);
dev_dbg(&alg_data->adapter.dev,
"%s(): Waking up xfer routine.\n",
__func__);
complete(&alg_data->mif.complete);
}
} else if (alg_data->mif.len == 0) {
/* */
i2c_pnx_stop(alg_data);
/* */
iowrite32(ioread32(I2C_REG_CTL(alg_data)) &
~(mcntrl_afie | mcntrl_naie | mcntrl_drmie),
I2C_REG_CTL(alg_data));
/* */
del_timer_sync(&alg_data->mif.timer);
dev_dbg(&alg_data->adapter.dev,
"%s(): Waking up xfer routine after zero-xfer.\n",
__func__);
complete(&alg_data->mif.complete);
}
dev_dbg(&alg_data->adapter.dev, "%s(): exiting: stat = %04x.\n",
__func__, ioread32(I2C_REG_STS(alg_data)));
return 0;
}
