Beispiel #1
0
int i2c_stm32_slave_unregister(struct device *dev,
			       struct i2c_slave_config *config)
{
	const struct i2c_stm32_config *cfg = DEV_CFG(dev);
	struct i2c_stm32_data *data = DEV_DATA(dev);
	I2C_TypeDef *i2c = cfg->i2c;

	if (!data->slave_attached) {
		return -EINVAL;
	}

	if (data->master_active) {
		return -EBUSY;
	}

	LL_I2C_DisableOwnAddress1(i2c);

	LL_I2C_DisableIT_ADDR(i2c);
	stm32_i2c_disable_transfer_interrupts(dev);

	LL_I2C_ClearFlag_NACK(i2c);
	LL_I2C_ClearFlag_STOP(i2c);
	LL_I2C_ClearFlag_ADDR(i2c);

	LL_I2C_Disable(i2c);

	SYS_LOG_DBG("i2c: slave unregistered");

	return 0;
}
/**
  * @brief  Initialize the I2C registers according to the specified parameters in I2C_InitStruct.
  * @param  I2Cx I2C Instance.
  * @param  I2C_InitStruct pointer to a @ref LL_I2C_InitTypeDef structure.
  * @retval An ErrorStatus enumeration value:
  *          - SUCCESS: I2C registers are initialized
  *          - ERROR: Not applicable
  */
uint32_t LL_I2C_Init(I2C_TypeDef *I2Cx, LL_I2C_InitTypeDef *I2C_InitStruct)
{
  /* Check the I2C Instance I2Cx */
  assert_param(IS_I2C_ALL_INSTANCE(I2Cx));

  /* Check the I2C parameters from I2C_InitStruct */
  assert_param(IS_LL_I2C_PERIPHERAL_MODE(I2C_InitStruct->PeripheralMode));
  assert_param(IS_LL_I2C_ANALOG_FILTER(I2C_InitStruct->AnalogFilter));
  assert_param(IS_LL_I2C_DIGITAL_FILTER(I2C_InitStruct->DigitalFilter));
  assert_param(IS_LL_I2C_OWN_ADDRESS1(I2C_InitStruct->OwnAddress1));
  assert_param(IS_LL_I2C_TYPE_ACKNOWLEDGE(I2C_InitStruct->TypeAcknowledge));
  assert_param(IS_LL_I2C_OWN_ADDRSIZE(I2C_InitStruct->OwnAddrSize));

  /* Disable the selected I2Cx Peripheral */
  LL_I2C_Disable(I2Cx);

  /*---------------------------- I2Cx CR1 Configuration ------------------------
   * Configure the analog and digital noise filters with parameters :
   * - AnalogFilter: I2C_CR1_ANFOFF bit
   * - DigitalFilter: I2C_CR1_DNF[3:0] bits
   */
  LL_I2C_ConfigFilters(I2Cx, I2C_InitStruct->AnalogFilter, I2C_InitStruct->DigitalFilter);

  /*---------------------------- I2Cx TIMINGR Configuration --------------------
   * Configure the SDA setup, hold time and the SCL high, low period with parameter :
   * - Timing: I2C_TIMINGR_PRESC[3:0], I2C_TIMINGR_SCLDEL[3:0], I2C_TIMINGR_SDADEL[3:0],
   *           I2C_TIMINGR_SCLH[7:0] and I2C_TIMINGR_SCLL[7:0] bits
   */
  LL_I2C_SetTiming(I2Cx, I2C_InitStruct->Timing);

  /* Enable the selected I2Cx Peripheral */
  LL_I2C_Enable(I2Cx);

  /*---------------------------- I2Cx OAR1 Configuration -----------------------
   * Disable, Configure and Enable I2Cx device own address 1 with parameters :
   * - OwnAddress1:  I2C_OAR1_OA1[9:0] bits
   * - OwnAddrSize:  I2C_OAR1_OA1MODE bit
   */
  LL_I2C_DisableOwnAddress1(I2Cx);
  LL_I2C_SetOwnAddress1(I2Cx, I2C_InitStruct->OwnAddress1, I2C_InitStruct->OwnAddrSize);
  LL_I2C_EnableOwnAddress1(I2Cx);

  /*---------------------------- I2Cx MODE Configuration -----------------------
  * Configure I2Cx peripheral mode with parameter :
   * - PeripheralMode: I2C_CR1_SMBDEN and I2C_CR1_SMBHEN bits
   */
  LL_I2C_SetMode(I2Cx, I2C_InitStruct->PeripheralMode);

  /*---------------------------- I2Cx CR2 Configuration ------------------------
   * Configure the ACKnowledge or Non ACKnowledge condition
   * after the address receive match code or next received byte with parameter :
   * - TypeAcknowledge: I2C_CR2_NACK bit
   */
  LL_I2C_AcknowledgeNextData(I2Cx, I2C_InitStruct->TypeAcknowledge);

  return SUCCESS;
}