/* mvUartConfig() prepares UART configuration (MPP's and UART interface selection) */
static inline MV_VOID mvUartConfig()
{
#if defined CONFIG_DB_88F6710_PCAC
MV_U32 uiReg = 0;
/* UART0 & I2C MPP's (MPP[0:1] = 0x1 */
uiReg = (MV_REG_READ(MPP_CONTROL_REG(0)) & 0xFFFFFF00) | 0x11;
MV_REG_WRITE(MPP_CONTROL_REG(0), uiReg);
#endif
}
void armadaxp_fabric_setup_deepIdle(void)
{
MV_U32 reg;
MV_U32 i;
reg = MV_REG_READ(MV_L2C_NFABRIC_PM_CTRL_CFG_REG);
reg |= MV_L2C_NFABRIC_PM_CTRL_CFG_PWR_DOWN;
MV_REG_WRITE(MV_L2C_NFABRIC_PM_CTRL_CFG_REG, reg);
for (i=0; i<4; i++) {
/* Enable L2 & Fabric powerdown in Deep-Idle mode */
reg = MV_REG_READ(PM_CONTROL_AND_CONFIG_REG(i));
reg |= PM_CONTROL_AND_CONFIG_L2_PWDDN;
MV_REG_WRITE(PM_CONTROL_AND_CONFIG_REG(i), reg);
}
/* Configure CPU_DivClk_Control0 */
reg = MV_REG_READ(0x18700);
reg &= ~0xFFFF00;
reg |= 0x10EF00;
MV_REG_WRITE(0x18700, reg);
/* Configure PMU_DFS_Control_1 */
reg = MV_REG_READ(0x1C054);
reg &= 0xFF000000;
reg >>= 24;
reg = (reg << 24) | ((reg + 1) << 16) | 0x10404;
MV_REG_WRITE(0x1C054, reg);
/* Configure PMU Program registers */
MV_REG_WRITE(0x1C270, 0x00c108a8);
MV_REG_WRITE(0x1C274, 0x0000005a);
MV_REG_WRITE(0x1C278, 0x00000000);
MV_REG_WRITE(0x1C27c, 0x195b0000);
MV_REG_WRITE(0x1C280, 0x00ff0014);
#ifdef CONFIG_ARMADA_XP_DEEP_IDLE_L2_WA
/* disable HW L2C Flush configure 0x22008:
* Set bit 4 -> Will skip HW L2C flush triggering.
* Set bit 5 -> Will skip waiting for HW L2C flush done indication.
*/
reg = MV_REG_READ(MV_L2C_NFABRIC_PWR_DOWN_FLOW_CTRL_REG);
reg |= 3 << 4;
/* Configure skiping the RA & WA Disable */
reg |= 1;
/* Configure skiping the Sharing Disable */
reg |= 1 << 8;
/* Configure skiping the CIB Ack Disable */
reg |= 1 << 6;
/* Configure skiping the RA & WA Resume */
reg |= 1 << 12;
/* Configure skiping the CIB Ack Resume */
reg |= 1 << 15;
/* Configure skiping the Sharing Resume */
reg |= 1 << 14;
MV_REG_WRITE(MV_L2C_NFABRIC_PWR_DOWN_FLOW_CTRL_REG, reg);
#endif
#ifdef CONFIG_ARMADA_XP_DEEP_IDLE_L2_WA
/* neet to restore this register on resume */
cib_ctrl_cfg_reg = MV_REG_READ(MV_CIB_CTRL_CFG_REG);
#endif
/* Set the resume control registers to do nothing */
MV_REG_WRITE(0x20980, 0);
MV_REG_WRITE(0x20988, 0);
/* configure the MPP29 used for CPU0+L2+Fabric power control*/
reg = MV_REG_READ(MPP_CONTROL_REG(3));
reg &= ~0x00F00000;
reg |= 0x00500000;
MV_REG_WRITE(MPP_CONTROL_REG(3), reg);
/* configure the MPP40 used for CPU1 power control*/
reg = MV_REG_READ(MPP_CONTROL_REG(5));
reg &= ~0x0000000F;
reg |= 0x00000003;
MV_REG_WRITE(MPP_CONTROL_REG(5), reg);
/* configure the MPP57 used for CPU2+3 power control*/
reg = MV_REG_READ(MPP_CONTROL_REG(7));
reg &= ~0x000000F0;
reg |= 0x00000020;
MV_REG_WRITE(MPP_CONTROL_REG(7), reg);
}
/*******************************************************************************
* mvCtrlHighSpeedSerdesPhyConfig
*
* DESCRIPTION: This is the main function which configure the
* PU sequence of the ser-des
*
* INPUT:
* None.
*
* OUTPUT:
* None.
*
* RETURN:
* MV_OK - success
* MV_ERROR - failure
*******************************************************************************/
MV_STATUS mvCtrlHighSpeedSerdesPhyConfig(MV_VOID)
{
MV_U32 serdesLaneNum, pexUnit;
MV_U32 uiReg;
MV_BIN_SERDES_UNIT_INDX serdesLaneCfg;
MV_U32 regAddr[16][11], regVal[16][11]; /* addr/value for each line @ every setup step */
MV_U8 maxSerdesLanes;
MV_U32 tmp;
MV_U32 tempReg, tempPexReg;
MV_U32 pexIf=0;
MV_U32 first_busno, next_busno;
MV_U32 addr;
MV_TWSI_ADDR slave;
MV_U32 boardId = mvBoardIdIndexGet(mvBoardIdGet());
maxSerdesLanes = mvCtrlSerdesMaxLanesGet();
if (maxSerdesLanes == 0)
return MV_OK;
/*Set MPP1 for twsi access */
uiReg = (MV_REG_READ(MPP_CONTROL_REG(1)) & 0x00FFFFFF) | 0x22000000;
MV_REG_WRITE(MPP_CONTROL_REG(1), uiReg);
/* TWSI init */
slave.type = ADDR7_BIT;
slave.address = 0;
mvTwsiInit(0, TWSI_SPEED, mvBoardTclkGet(), &slave, 0);
mvUartInit();
/* update board configuration (serdes lane topology and speed), if needed */
mvBoardUpdateBoardTopologyConfig(boardId);
/* Initialize board configuration database */
boardLaneConfig[0] = SERDES_UNIT_PEX; /* SerDes 0 is alwyas PCIe0*/
boardLaneConfig[1] = boardTopologyConfig[boardId].serdesTopology.lane1;
boardLaneConfig[2] = boardTopologyConfig[boardId].serdesTopology.lane2;
boardLaneConfig[3] = boardTopologyConfig[boardId].serdesTopology.lane3;
memset(regAddr, 0, sizeof(regAddr));
memset(regVal, 0, sizeof(regVal));
/* Check if DRAM is already initialized */
if (MV_REG_READ(REG_BOOTROM_ROUTINE_ADDR) & (1 << REG_BOOTROM_ROUTINE_DRAM_INIT_OFFS)) {
DEBUG_INIT_S("High speed PHY - Version: ");
DEBUG_INIT_S(SERDES_VERION);
DEBUG_INIT_S(" - 2nd boot - Skip \n");
return MV_OK;
}
DEBUG_INIT_S("High speed PHY - Version: ");
DEBUG_INIT_S(SERDES_VERION);
DEBUG_INIT_S(" (COM-PHY-V20) \n");
DEBUG_INIT_FULL_C("SERDES 0=",boardLaneConfig[0],2);
DEBUG_INIT_FULL_C("SERDES 1=",boardLaneConfig[1],2);
DEBUG_INIT_FULL_C("SERDES 2=",boardLaneConfig[2],2);
DEBUG_INIT_FULL_C("SERDES 3=",boardLaneConfig[3],2);
/*------------------------------------------*/
/* STEP - 1.5 Power Down PLL, RX, TX all phys */
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
uiReg=MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
uiReg &= ~PIN_TX_IDLE_MASK;
uiReg &= ~(PHY_POWER_UP_PLL_MASK | PHY_POWER_UP_RX_MASK | PHY_POWER_UP_TX_MASK);
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
mvOsUDelay(10000);
/*--------------------------------------------------------*/
/* STEP - 2 Reset PHY and PIPE (Zx: Un-reset, Ax: Reset)*/
/*--------------------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
#ifndef CONFIG_ALP_A375_ZX_REV
resetPhyAndPipe(serdesLaneNum, MV_TRUE);
#else
resetPhyAndPipe(serdesLaneNum, MV_FALSE);
#endif
}
/*--------------------------------*/
/* STEP - 2 Common PHYs Selectors */
/*--------------------------------*/
MV_REG_WRITE(COMMON_PHY_SELECTOR_REG, GetLaneSelectorConfig());
/*--------------------------------*/
/* STEP - 3 Configuration 1 */
/*--------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
uiReg = MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
switch(serdesLaneCfg){
case SERDES_UNIT_USB3:
#ifndef CONFIG_ALP_A375_ZX_REV
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
uiReg |= PHY_MODE_MASK; /* PHY Mode = USB */
uiReg |= PIPE_SELECT_MASK ; /* Select USB3_PEX */
break;
case SERDES_UNIT_PEX:
uiReg |= PIPE_SELECT_MASK ; /* Select USB3_PEX */
#ifndef CONFIG_ALP_A375_ZX_REV
uiReg &= ~(PHY_MODE_MASK); /* PHY Mode = PEX */
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
break;
case SERDES_UNIT_SGMII:
case SERDES_UNIT_SATA:
#ifndef CONFIG_ALP_A375_ZX_REV
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
uiReg &= ~(PIPE_SELECT_MASK); /* Select SATA_SGMII */
uiReg |= POWER_UP_IVREF_MASK; /* Power UP IVREF = Power Up */
break;
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
/* Serdes speed config */
tmp = getSerdesSpeedConfig(boardId, serdesLaneCfg);
uiReg &= ~(GEN_RX_MASK); /* SERDES RX Speed config */
uiReg |= tmp<<GEN_RX_OFFS;
uiReg &= ~(GEN_TX_MASK); /* SERDES TX Speed config */
uiReg |= tmp<<GEN_TX_OFFS;
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
#ifndef CONFIG_ALP_A375_ZX_REV
/*------------------------------------------*/
/* STEP - 3.5 Unreset PHY and PIPE(only Ax)*/
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
resetPhyAndPipe(serdesLaneNum, MV_FALSE);
}
#endif
/*----------------------------------------*/
/* STEP - 4 COMPHY register configuration */
/*----------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
switch(serdesLaneCfg){
case SERDES_UNIT_PEX:
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x25); /* Enable soft_reset*/
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC60); /* PHY Mode = PEX */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6017); /* REFCLK SEL =0x0 (100Mhz) */
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(KVCO_CALOBRATION_CONTROL_REG(serdesLaneNum),0x40); /* use_max_pll_rate=0x0, ext_force_cal_done=0x0 */
#endif
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x24); /* Release soft_reset */
break;
case SERDES_UNIT_USB3:
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x21); /* Enable soft_reset*/
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFCA0); /* PHY Mode = USB3 */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(LANE_CONFIGURATION_4_REG(serdesLaneNum),0x13); /* Ref_Clk =100Mhz */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6017); /* REFCLK SEL =0x0 (100Mhz) */
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(KVCO_CALOBRATION_CONTROL_REG(serdesLaneNum),0x40); /* use_max_pll_rate=0x0, ext_force_cal_done=0x0 */
MV_REG_WRITE(GENERETION_2_SETTINGS_1_REG(serdesLaneNum),0x149); /* Mulitiple frequency setup */
#endif
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x20); /* Release soft_reset */
break;
case SERDES_UNIT_SATA:
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC01); /* PHY Mode = SATA */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6417); /* REFCLK SEL =0x1 (25Mhz) */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
MV_REG_WRITE(DIGITAL_RESERVED0_REG(serdesLaneNum),0xE); /* Reg_sq_de_glitch_en */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(RESERVED_46_REG(serdesLaneNum),0xFF00);
#endif
break;
case SERDES_UNIT_SGMII:
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC81); /* PHY Mode = SGMII */ /*moti need to change offset*/
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x0); /* SEL_BITS = 0x0 (10-bits mode) */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6417); /* REFCLK SEL =0x1 (25Mhz) */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(DIGITAL_RESERVED0_REG(serdesLaneNum),0xE); /* Reg_sq_de_glitch_en */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(RESERVED_46_REG(serdesLaneNum),0xFF00); /* Enable soft_reset*/
#endif
MV_REG_WRITE(PHY_ISOLATION_MODE_CONTROL_REG(serdesLaneNum),0x166); /* Set PHY_GEN_TX/RX to 1.25Gbps */
break;
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
}
/*------------------------------------------*/
/* STEP - 4.5 Power up PLL, RX, TX all phys */
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
uiReg=MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
uiReg |= (PHY_POWER_UP_PLL_MASK | PHY_POWER_UP_RX_MASK | PHY_POWER_UP_TX_MASK);
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
#ifndef CONFIG_ALP_A375_ZX_REV
mvOsUDelay(5000);
/*--------------------------------------------------------------------*/
/* STEP - 4.6 (Only SGMII/SATA): WAIT for PHY Power up sequence to finish */
/*--------------------------------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
switch(serdesLaneCfg){
case SERDES_UNIT_SATA:
case SERDES_UNIT_SGMII:
uiReg = MV_REG_READ(COMMON_PHY_STATUS1_REG(serdesLaneNum));
if ((uiReg & 0x6) != 0x6) {
DEBUG_INIT_S("Phy Power up did't finished\n");
return MV_ERROR;
}
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
}
#endif
/*----------------------------------------*/
/* STEP - 5 PEX Only */
/*----------------------------------------*/
for (pexUnit = 0; pexUnit < 4; pexUnit++) {
if (boardLaneConfig[pexUnit] != SERDES_UNIT_PEX)
continue;
tmp = MV_REG_READ(PEX_CAPABILITIES_REG(pexUnit));
DEBUG_RD_REG(PEX_CAPABILITIES_REG(pexUnit), tmp );
tmp &= ~(0xf<<20);
tmp |= (0x4<<20);
MV_REG_WRITE(PEX_CAPABILITIES_REG(pexUnit),tmp);
DEBUG_WR_REG(PEX_CAPABILITIES_REG(pexUnit),tmp);
}
tmp = MV_REG_READ(SOC_CTRL_REG);
DEBUG_RD_REG(SOC_CTRL_REG, tmp);
tmp &= ~(0x03);
tmp |= 0x1<<PCIE0_ENABLE_OFFS;
if (boardLaneConfig[1] == SERDES_UNIT_PEX)
tmp |= 0x1<<PCIE1_ENABLE_OFFS;
MV_REG_WRITE(SOC_CTRL_REG, tmp);
DEBUG_WR_REG(SOC_CTRL_REG, tmp);
/*----------------------------------------*/
/* STEP - 6 PEX Only - support gen1/gen2 */
/*----------------------------------------*/
next_busno = 0;
mvOsDelay(150);
for (pexIf = 0; pexIf < 2; pexIf++) // only pexIf 0 on
{
if (boardLaneConfig[pexIf] != SERDES_UNIT_PEX)
continue;
tmp = MV_REG_READ(PEX_DBG_STATUS_REG(pexIf));
DEBUG_RD_REG(PEX_DBG_STATUS_REG(pexIf), tmp);
first_busno = next_busno;
if ((tmp & 0x7f) == 0x7E) {
next_busno++;
tempPexReg = MV_REG_READ((PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CAPABILITY_REG)));
DEBUG_RD_REG((PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CAPABILITY_REG)),tempPexReg );
tempPexReg &= (0xF);
if (tempPexReg == 0x2) {
tempReg = (MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CTRL_STAT_REG)) & 0xF0000) >> 16;
DEBUG_RD_REG(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CTRL_STAT_REG),tempReg );
/* check if the link established is GEN1 */
if (tempReg == 0x1) {
mvPexLocalBusNumSet(pexIf, first_busno);
mvPexLocalDevNumSet(pexIf, 1);
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", link is Gen1, checking the EP capability \n");
/* link is Gen1, check the EP capability */
addr = mvPexConfigRead(pexIf, first_busno, 0, 0, 0x34) & 0xFF;
DEBUG_INIT_FULL_C("mvPexConfigRead: return addr=0x%x", addr,4);
if (addr == 0xff) {
DEBUG_INIT_FULL_C("mvPexConfigRead: return 0xff -->PEX (%d): Detected No Link.", pexIf,1);
continue;
}
while ((mvPexConfigRead(pexIf, first_busno, 0, 0, addr) & 0xFF) != 0x10) {
addr = (mvPexConfigRead(pexIf, first_busno, 0, 0, addr) & 0xFF00) >> 8;
}
if ((mvPexConfigRead(pexIf, first_busno, 0, 0, addr + 0xC) & 0xF) >= 0x2) {
tmp = MV_REG_READ(PEX_LINK_CTRL_STATUS2_REG(pexIf));
DEBUG_RD_REG(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp );
tmp &=~(BIT0 | BIT1);
tmp |= BIT1;
MV_REG_WRITE(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp);
DEBUG_WR_REG(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp);
tmp = MV_REG_READ(PEX_CTRL_REG(pexIf));
DEBUG_RD_REG(PEX_CTRL_REG(pexIf), tmp );
tmp |= BIT10;
MV_REG_WRITE(PEX_CTRL_REG(pexIf),tmp);
DEBUG_WR_REG(PEX_CTRL_REG(pexIf),tmp);
mvOsUDelay(10000);/* We need to wait 10ms before reading the PEX_DBG_STATUS_REG in order not to read the status of the former state*/
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", Link upgraded to Gen2 based on client cpabilities \n");
} else {
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", remains Gen1\n");
}
}
}
