void mico_system_delegate_config_success( mico_config_source_t source )
{
config_delegate_log_trace();
#ifdef USE_MiCOKit_EXT
char oled_show_line[OLED_DISPLAY_MAX_CHAR_PER_ROW+1] = {'\0'};
#endif
config_delegate_log( "Wi-Fi configed by: %d", source );
MicoGpioOutputLow((mico_gpio_t)MICO_SYS_LED);
#ifdef USE_MiCOKit_EXT
memset(oled_show_line, '\0', OLED_DISPLAY_MAX_CHAR_PER_ROW+1);
if(CONFIG_BY_AIRKISS == source){
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"Airkiss success ");
}else if(CONFIG_BY_SOFT_AP == source){
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"SoftAP success ");
}else if(CONFIG_BY_WAC == source){
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"WAC success ");
}else if( (CONFIG_BY_EASYLINK_V2 == source) || (CONFIG_BY_EASYLINK_PLUS == source) ||
(CONFIG_BY_EASYLINK_MINUS == source) ){
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"Easylink success");
}else{
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"Unknown ");
}
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_2, (uint8_t*)oled_show_line);
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_3, (uint8_t*)" ");
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_4, (uint8_t*)" ");
#endif
return;
}
void init_platform( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
// MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
//MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
// Initialise EasyLink buttons
MicoGpioInitialize( (mico_gpio_t)EasyLink_BUTTON, INPUT_PULL_UP );
mico_init_timer(&_button_EL_timer, RestoreDefault_TimeOut, _button_EL_Timeout_handler, NULL);
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_BOTH_EDGES, _button_EL_irq_handler, NULL );
//MicoFlashInitialize( MICO_SPI_FLASH );
#ifdef USE_MiCOKit_EXT
dc_motor_init( );
dc_motor_set( 0 );
rgb_led_init();
rgb_led_open(0, 0, 0);
#endif
}
static OSStatus platform_reset_wlan_powersave_clock( void )
{
/* Tie the pin to ground */
MicoGpioInitialize( (mico_gpio_t) MICO_GPIO_WLAN_POWERSAVE_CLOCK, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t) MICO_GPIO_WLAN_POWERSAVE_CLOCK );
return kNoErr;
}
void init_platform( void )
{
button_init_t init;
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
init.gpio = EasyLink_BUTTON;
init.pressed_func = PlatformEasyLinkButtonClickedCallback;
init.long_pressed_func = PlatformEasyLinkButtonLongPressedCallback;
init.long_pressed_timeout = 5000;
button_init( IOBUTTON_EASYLINK, init );
#ifdef USE_MiCOKit_EXT
dc_motor_init( );
dc_motor_set( 0 );
rgb_led_init();
rgb_led_open(0, 0, 0);
#endif
}
void setLightState_command(char *property, mico_Context_t * const inContext)
{
if(0==strcmp(property, "light 0")){
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
}else if(0==strcmp(property, "light 1")){
MicoGpioOutputHigh( (mico_gpio_t)MICO_SYS_LED );
}
}
void MicoRfLed(bool onoff)
{
if (onoff) {
MicoGpioOutputLow( (mico_gpio_t)MICO_RF_LED );
} else {
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
}
}
void ResetF411(void)
{
MicoGpioOutputLow(F411_RESET_PIN);
mico_thread_msleep(100);
MicoGpioOutputHigh(F411_RESET_PIN);
mico_thread_msleep(100);
AaSysLogPrint(LOGLEVEL_INF, "f411 rest done");
}
void init_platform_bootloader( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_HIGH_IMPEDANCE);
}
void ConfigWillStop( mico_Context_t * const inContext )
{
(void)(inContext);
config_delegate_log_trace();
mico_stop_timer(&_Led_EL_timer);
mico_deinit_timer( &_Led_EL_timer );
MicoGpioOutputLow((mico_gpio_t)MICO_SYS_LED);
return;
}
void host_platform_reset_wifi( bool reset_asserted )
{
if ( reset_asserted == true )
{
MicoGpioOutputLow( (mico_gpio_t)WL_RESET );
}
else
{
MicoGpioOutputHigh( (mico_gpio_t)WL_RESET );
}
}
void host_platform_power_wifi( bool power_enabled )
{
if ( power_enabled == true )
{
MicoGpioOutputLow( (mico_gpio_t)WL_REG );
}
else
{
MicoGpioOutputHigh( (mico_gpio_t)WL_REG );
}
}
void init_platform_bootloader( void )
{
OSStatus err = kNoErr;
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
}
void init_platform( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
// Initialise EasyLink buttons
MicoGpioInitialize( (mico_gpio_t)EasyLink_BUTTON, INPUT_PULL_UP );
mico_init_timer(&_button_EL_timer, RestoreDefault_TimeOut, _button_EL_Timeout_handler, NULL);
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_BOTH_EDGES, _button_EL_irq_handler, NULL );
}
void init_platform_bootloader( void )
{
MicoGpioInitialize( MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputHigh( MICO_SYS_LED );
MicoGpioInitialize( MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( MICO_RF_LED );
MicoGpioInitialize(BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize(MFG_SEL, INPUT_PULL_UP);
#ifdef USE_MiCOKit_EXT
MicoGpioInitialize( Arduino_D9, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( Arduino_D9 );
#endif
}
void init_platform( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
// Initialise EasyLink buttons
MicoGpioInitialize( (mico_gpio_t)EasyLink_BUTTON, INPUT_HIGH_IMPEDANCE );
mico_init_timer(&_button_EL_timer, RestoreDefault_TimeOut, _button_EL_Timeout_handler, NULL);
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_BOTH_EDGES, _button_EL_irq_handler, NULL );
#ifdef USE_MiCOKit_EXT
dc_motor_init( );
dc_motor_set( 0 );
#endif
}
void init_platform( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
// Initialise EasyLink buttons
MicoGpioInitialize( (mico_gpio_t)EasyLink_BUTTON, INPUT_PULL_UP );
mico_init_timer(&_button_EL_timer, RestoreDefault_TimeOut, _button_EL_Timeout_handler, NULL);
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_BOTH_EDGES, _button_EL_irq_handler, NULL );
// Initialise Standby/wakeup switcher
MicoGpioInitialize( (mico_gpio_t)Standby_SEL, INPUT_PULL_UP );
MicoGpioEnableIRQ( (mico_gpio_t)Standby_SEL , IRQ_TRIGGER_FALLING_EDGE, _button_STANDBY_irq_handler, NULL);
MicoFlashInitialize( MICO_SPI_FLASH );
}
void init_platform_bootloader( void )
{
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_HIGH_IMPEDANCE);
#ifdef USE_MiCOKit_EXT
dc_motor_init( );
dc_motor_set( 0 );
rgb_led_init();
rgb_led_open(0, 0, 0);
#endif
}
void ConfigWillStop( mico_Context_t * const inContext )
{
(void)(inContext);
config_delegate_log_trace();
#ifdef USE_MiCOKit_EXT
char oled_show_line[OLED_DISPLAY_MAX_CHAR_PER_ROW+1] = {'\0'};
#endif
mico_stop_timer(&_Led_EL_timer);
mico_deinit_timer( &_Led_EL_timer );
MicoGpioOutputLow((mico_gpio_t)MICO_SYS_LED);
#ifdef USE_MiCOKit_EXT
memset(oled_show_line, '\0', OLED_DISPLAY_MAX_CHAR_PER_ROW+1);
snprintf(oled_show_line, OLED_DISPLAY_MAX_CHAR_PER_ROW+1, "%s", (uint8_t*)"Config ");
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_2, (uint8_t*)oled_show_line);
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_3, " Stop. ");
OLED_ShowString(OLED_DISPLAY_COLUMN_START, OLED_DISPLAY_ROW_4, " ");
#endif
return;
}
static void _button_EL_irq_handler( void* arg )
{
(void)(arg);
int interval = -1;
mico_start_timer(&_button_EL_timer);
if ( MicoGpioInputGet( (mico_gpio_t)EasyLink_BUTTON ) == 0 ) {
_default_start_time = mico_get_time()+1;
mico_start_timer(&_button_EL_timer);
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_RISING_EDGE, _button_EL_irq_handler, NULL );
} else {
interval = mico_get_time() + 1 - _default_start_time;
if ( (_default_start_time != 0) && interval > 50 && interval < RestoreDefault_TimeOut){
/* EasyLink button clicked once */
PlatformEasyLinkButtonClickedCallback();
//platform_log("PlatformEasyLinkButtonClickedCallback!");
MicoGpioOutputLow( (mico_gpio_t)MICO_RF_LED );
MicoGpioEnableIRQ( (mico_gpio_t)EasyLink_BUTTON, IRQ_TRIGGER_FALLING_EDGE, _button_EL_irq_handler, NULL );
}
mico_stop_timer(&_button_EL_timer);
_default_start_time = 0;
}
}
void init_platform_bootloader( void )
{
OSStatus err = kNoErr;
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
/* Specific operations used in EMW3165 production */
#define NEED_RF_DRIVER_COPY_BASE ((uint32_t)0x08008000)
#define TEMP_RF_DRIVER_BASE ((uint32_t)0x08040000)
#define TEMP_RF_DRIVER_END ((uint32_t)0x0807FFFF)
const uint8_t isDriverNeedCopy = *(uint8_t *)(NEED_RF_DRIVER_COPY_BASE);
const uint32_t totalLength = ( DRIVER_FLASH_SIZE < 0x40000)? DRIVER_FLASH_SIZE:0x40000;
const uint8_t crcResult = *(uint8_t *)(TEMP_RF_DRIVER_END);
uint8_t targetCrcResult = 0;
uint32_t copyLength;
uint32_t destStartAddress_tmp = DRIVER_START_ADDRESS;
uint32_t sourceStartAddress_tmp = TEMP_RF_DRIVER_BASE;
uint32_t i;
if ( isDriverNeedCopy != 0x0 )
return;
platform_log( "Bootloader start to copy RF driver..." );
/* Copy RF driver to SPI flash */
err = MicoFlashInitialize( (mico_flash_t)MICO_FLASH_FOR_DRIVER );
require_noerr(err, exit);
err = MicoFlashInitialize( (mico_flash_t)MICO_INTERNAL_FLASH );
require_noerr(err, exit);
err = MicoFlashErase( MICO_FLASH_FOR_DRIVER, DRIVER_START_ADDRESS, DRIVER_END_ADDRESS );
require_noerr(err, exit);
platform_log( "Time: %d", mico_get_time_no_os() );
for(i = 0; i <= totalLength/SizePerRW; i++){
if( i == totalLength/SizePerRW ){
if(totalLength%SizePerRW)
copyLength = totalLength%SizePerRW;
else
break;
}else{
copyLength = SizePerRW;
}
printf(".");
err = MicoFlashRead( MICO_INTERNAL_FLASH, &sourceStartAddress_tmp, data , copyLength );
require_noerr( err, exit );
err = MicoFlashWrite( MICO_FLASH_FOR_DRIVER, &destStartAddress_tmp, data, copyLength);
require_noerr(err, exit);
}
printf("\r\n");
/* Check CRC-8 check-sum */
platform_log( "Bootloader start to verify RF driver..." );
sourceStartAddress_tmp = TEMP_RF_DRIVER_BASE;
destStartAddress_tmp = DRIVER_START_ADDRESS;
for(i = 0; i <= totalLength/SizePerRW; i++){
if( i == totalLength/SizePerRW ){
if(totalLength%SizePerRW)
copyLength = totalLength%SizePerRW;
else
break;
}else{
copyLength = SizePerRW;
}
printf(".");
err = MicoFlashRead( MICO_FLASH_FOR_DRIVER, &destStartAddress_tmp, data, copyLength );
require_noerr( err, exit );
targetCrcResult = CRC8_Table(targetCrcResult, data, copyLength);
}
printf("\r\n");
//require_string( crcResult == targetCrcResult, exit, "Check-sum error" );
if( crcResult != targetCrcResult ){
platform_log("Check-sum error");
while(1);
}
/* Clear RF driver from temperary storage */
platform_log("Bootloader start to clear RF driver temporary storage...");
err = MicoFlashInitialize( (mico_flash_t)MICO_INTERNAL_FLASH );
require_noerr(err, exit);
/* Clear copy tag */
err = MicoFlashErase(MICO_INTERNAL_FLASH, NEED_RF_DRIVER_COPY_BASE, NEED_RF_DRIVER_COPY_BASE);
require_noerr(err, exit);
exit:
MicoFlashFinalize( MICO_INTERNAL_FLASH );
MicoFlashFinalize( MICO_FLASH_FOR_DRIVER );
}
OSStatus host_platform_bus_init( void )
{
SPI_InitTypeDef spi_init;
DMA_InitTypeDef dma_init_structure;
GPIO_InitTypeDef gpio_init_structure;
NVIC_InitTypeDef nvic_init_structure;
MCU_CLOCKS_NEEDED();
mico_rtos_init_semaphore(&spi_transfer_finished_semaphore, 1);
/* Enable SPI_SLAVE DMA clock */
RCC_AHB1PeriphClockCmd( SPIX_DMA_CLK, ENABLE );
/* Enable SPI_SLAVE Periph clock */
SPIX_CLK_FUNCTION( SPIX_CLK, ENABLE );
/* Enable GPIO Bank B & C */
RCC_AHB1PeriphClockCmd( SPI_BUS_CLOCK_BANK_CLK | SPI_BUS_MISO_BANK_CLK | SPI_BUS_MOSI_BANK_CLK | SPI_BUS_CS_BANK_CLK | SPI_IRQ_CLK, ENABLE );
/* Enable SYSCFG. Needed for selecting EXTI interrupt line */
RCC_APB2PeriphClockCmd( RCC_APB2Periph_SYSCFG, ENABLE );
/* Setup the interrupt input for WLAN_IRQ */
gpio_init_structure.GPIO_Mode = GPIO_Mode_IN;
gpio_init_structure.GPIO_PuPd = GPIO_PuPd_NOPULL;
gpio_init_structure.GPIO_Speed = GPIO_Speed_100MHz;
gpio_init_structure.GPIO_Pin = ( 1 << SPI_IRQ_PIN );
GPIO_Init( SPI_IRQ_BANK, &gpio_init_structure );
gpio_irq_enable(SPI_IRQ_BANK, SPI_IRQ_PIN, IRQ_TRIGGER_RISING_EDGE, spi_irq_handler, 0);
/* Setup the SPI lines */
/* Setup SPI slave select GPIOs */
gpio_init_structure.GPIO_Mode = GPIO_Mode_AF;
gpio_init_structure.GPIO_OType = GPIO_OType_PP;
gpio_init_structure.GPIO_Speed = GPIO_Speed_100MHz;
gpio_init_structure.GPIO_Pin = ( 1 << SPI_BUS_CLOCK_PIN ) | ( 1 << SPI_BUS_MISO_PIN ) | ( 1 << SPI_BUS_MOSI_PIN );
GPIO_Init( SPI_BUS_CLOCK_BANK, &gpio_init_structure );
GPIO_PinAFConfig( SPI_BUS_CLOCK_BANK, SPI_BUS_CLOCK_PIN, SPIX_AF );
GPIO_PinAFConfig( SPI_BUS_MISO_BANK, SPI_BUS_MISO_PIN, SPIX_AF );
GPIO_PinAFConfig( SPI_BUS_MOSI_BANK, SPI_BUS_MOSI_PIN, SPIX_AF );
/* Setup SPI slave select GPIOs */
gpio_init_structure.GPIO_Mode = GPIO_Mode_OUT;
gpio_init_structure.GPIO_OType = GPIO_OType_PP;
gpio_init_structure.GPIO_Speed = GPIO_Speed_100MHz;
gpio_init_structure.GPIO_Pin = ( 1 << SPI_BUS_CS_PIN );
GPIO_Init( SPI_BUS_CS_BANK, &gpio_init_structure );
GPIO_SetBits( SPI_BUS_CS_BANK, ( 1 << SPI_BUS_CS_PIN ) ); /* Set CS high (disabled) */
/* Set GPIO_B[1:0] to 01 to put WLAN module into gSPI mode */
MicoGpioInitialize( (mico_gpio_t)WL_GPIO0, OUTPUT_PUSH_PULL );
MicoGpioOutputHigh( (mico_gpio_t)WL_GPIO0 );
MicoGpioInitialize( (mico_gpio_t)WL_GPIO1, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)WL_GPIO1 );
/* Setup DMA for SPIX RX */
DMA_DeInit( SPIX_DMA_RX_STREAM );
dma_init_structure.DMA_Channel = SPIX_DMA_RX_CHANNEL;
dma_init_structure.DMA_PeripheralBaseAddr = (uint32_t) &SPIX->DR;
dma_init_structure.DMA_Memory0BaseAddr = 0;
dma_init_structure.DMA_DIR = DMA_DIR_PeripheralToMemory;
dma_init_structure.DMA_BufferSize = 0;
dma_init_structure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
dma_init_structure.DMA_MemoryInc = DMA_MemoryInc_Enable;
dma_init_structure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
dma_init_structure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
dma_init_structure.DMA_Mode = DMA_Mode_Normal;
dma_init_structure.DMA_Priority = DMA_Priority_VeryHigh;
dma_init_structure.DMA_FIFOMode = DMA_FIFOMode_Disable;
dma_init_structure.DMA_FIFOThreshold = DMA_FIFOThreshold_Full;
dma_init_structure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
dma_init_structure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init( SPIX_DMA_RX_STREAM, &dma_init_structure );
/* Setup DMA for SPIX TX */
DMA_DeInit( SPIX_DMA_TX_STREAM );
dma_init_structure.DMA_Channel = SPIX_DMA_TX_CHANNEL;
dma_init_structure.DMA_PeripheralBaseAddr = (uint32_t) &SPIX->DR;
dma_init_structure.DMA_Memory0BaseAddr = 0;
dma_init_structure.DMA_DIR = DMA_DIR_MemoryToPeripheral;
dma_init_structure.DMA_BufferSize = 0;
dma_init_structure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
dma_init_structure.DMA_MemoryInc = DMA_MemoryInc_Enable;
dma_init_structure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
dma_init_structure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
dma_init_structure.DMA_Mode = DMA_Mode_Normal;
dma_init_structure.DMA_Priority = DMA_Priority_VeryHigh;
dma_init_structure.DMA_FIFOMode = DMA_FIFOMode_Disable;
dma_init_structure.DMA_FIFOThreshold = DMA_FIFOThreshold_Full;
dma_init_structure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
dma_init_structure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init( SPIX_DMA_TX_STREAM, &dma_init_structure );
/* Must be lower priority than the value of configMAX_SYSCALL_INTERRUPT_PRIORITY */
/* otherwise FreeRTOS will not be able to mask the interrupt */
/* keep in mind that ARMCM3 interrupt priority logic is inverted, the highest value */
/* is the lowest priority */
nvic_init_structure.NVIC_IRQChannel = SPIX_DMA_RX_IRQ_CHANNEL;
nvic_init_structure.NVIC_IRQChannelPreemptionPriority = (uint8_t) 0x3;
nvic_init_structure.NVIC_IRQChannelSubPriority = 0x0;
nvic_init_structure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init( &nvic_init_structure );
DMA_ITConfig(SPIX_DMA_RX_STREAM, DMA_IT_TC, ENABLE);
/* Enable DMA for TX */
SPI_I2S_DMACmd( SPIX, SPI_I2S_DMAReq_Tx | SPI_I2S_DMAReq_Rx, ENABLE );
/* Setup SPI */
spi_init.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
spi_init.SPI_Mode = SPI_Mode_Master;
spi_init.SPI_DataSize = SPI_DataSize_8b;
spi_init.SPI_CPOL = SPI_CPOL_High;
spi_init.SPI_CPHA = SPI_CPHA_2Edge;
spi_init.SPI_NSS = SPI_NSS_Soft;
spi_init.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2;
spi_init.SPI_FirstBit = SPI_FirstBit_MSB;
spi_init.SPI_CRCPolynomial = (uint16_t) 7;
/* Init SPI and enable it */
SPI_Init( SPIX, &spi_init );
SPI_Cmd( SPIX, ENABLE );
MCU_CLOCKS_NOT_NEEDED();
return kNoErr;
}
OSStatus host_platform_spi_transfer( bus_transfer_direction_t dir, uint8_t* buffer, uint16_t buffer_length )
{
OSStatus result;
uint8_t *junk;
platform_mcu_powersave_disable();
#ifdef USE_OWN_SPI_DRV
pdc_packet_t pdc_spi_packet;
pdc_spi_packet.ul_addr = (uint32_t)buffer;
pdc_spi_packet.ul_size = buffer_length;
pdc_tx_init(spi_m_pdc, &pdc_spi_packet, NULL);
if ( dir == BUS_READ ) {
pdc_spi_packet.ul_addr = (uint32_t)buffer;
pdc_spi_packet.ul_size = buffer_length;
}
if ( dir == BUS_WRITE ) {
junk = malloc(buffer_length);
pdc_spi_packet.ul_addr = (uint32_t)junk;
pdc_spi_packet.ul_size = buffer_length;
}
pdc_rx_init(spi_m_pdc, &pdc_spi_packet, NULL);
#if 0
if ( dir == BUS_WRITE ) {
spi_enable_interrupt(SPI_MASTER_BASE, SPI_IER_ENDTX);
NVIC_EnableIRQ(SPI_IRQn);
}
else {
spi_enable_interrupt(SPI_MASTER_BASE, SPI_IER_ENDRX);
NVIC_EnableIRQ(SPI_IRQn);
}
#endif
//platform_log("dir = %d, len = %d",dir, buffer_length);//TBD
#ifndef HARD_CS_NSS0
MicoGpioOutputLow( MICO_GPIO_15 );
#endif
/* Enable the RX and TX PDC transfer requests */
pdc_enable_transfer(spi_m_pdc, PERIPH_PTCR_TXTEN | PERIPH_PTCR_RXTEN);//pdc buffer address increase automatic.
//platform_log("pdc status = 0x%x",pdc_read_status(spi_m_pdc));
#ifndef NO_MICO_RTOS
result = mico_rtos_get_semaphore( &spi_transfer_finished_semaphore, 100 );
#else
/* Waiting transfer done*/
while((spi_read_status(SPI_MASTER_BASE) & SPI_SR_RXBUFF) == 0) {
__asm("wfi");
}
#endif
if ( dir == BUS_WRITE ) {
if (junk)
free(junk);
}
/* Disable the RX and TX PDC transfer requests */
pdc_disable_transfer(spi_m_pdc, PERIPH_PTCR_RXTDIS | PERIPH_PTCR_TXTDIS);
#ifndef HARD_CS_NSS0
MicoGpioOutputHigh( MICO_GPIO_15 );
#endif
#if 1
//clear PDC Perph Status flags
pdc_spi_packet.ul_addr = NULL;
pdc_spi_packet.ul_size = 3;
pdc_tx_init(spi_m_pdc, &pdc_spi_packet, NULL);
pdc_rx_init(spi_m_pdc, &pdc_spi_packet, NULL);
#endif
#else //spi_master_vec :
tx_dscr[0].data = buffer;
tx_dscr[0].length = buffer_length;
tx_dscr[1].data = NULL;
tx_dscr[1].length = 0;
//if ( dir == BUS_READ ) {
rx_dscr[0].data = buffer;
rx_dscr[0].length = buffer_length;
//} else {
// rx_dscr[0].data = &junk;
// rx_dscr[0].length = 0;
//}
rx_dscr[1].data = NULL;
rx_dscr[1].length = 0;
#ifndef HARD_CS_NSS0
mico_gpio_output_low( MICO_GPIO_15 );
#endif
if (spi_master_vec_transceive_buffer_wait(&spi_master, tx_dscr, rx_dscr) != STATUS_OK) {
platform_log("STATUS = -1");
return kGeneralErr;
}
#ifndef HARD_CS_NSS0
mico_gpio_output_high( MICO_GPIO_15 );
#endif
#endif /* USE_OWN_SPI_DR */
platform_mcu_powersave_enable();
#ifdef USE_OWN_SPI_DRV
return result;
#else
return 0;
#endif
}
OSStatus MicoSpiTransfer( const mico_spi_device_t* spi, mico_spi_message_segment_t* segments, uint16_t number_of_segments )
{
OSStatus result = kNoErr;
uint16_t i;
uint32_t count = 0;
check_string( (spi != NULL) && (segments != NULL) && (number_of_segments != 0), "Bad args");
MicoMcuPowerSaveConfig(false);
/* If the given SPI device is not the current SPI device, initialise */
if ( spi != current_spi_device )
{
MicoSpiInitialize( spi );
}
/* Activate chip select */
MicoGpioOutputLow(spi->chip_select);
for ( i = 0; i < number_of_segments; i++ )
{
/* Check if we are using DMA */
if ( spi->mode & SPI_USE_DMA )
{
spi_dma_config( spi, &segments[i] );
result = spi_dma_transfer( spi );
if ( result != kNoErr )
{
goto cleanup_transfer;
}
}
else
{
/* in interrupt-less mode */
if ( spi->bits == 8 )
{
const uint8_t* send_ptr = ( const uint8_t* )segments[i].tx_buffer;
uint8_t* rcv_ptr = ( uint8_t* )segments[i].rx_buffer;
count = segments[i].length;
while ( count-- )
{
uint16_t data;
if ( send_ptr != NULL )
{
data = *send_ptr;
send_ptr++;
}
else
{
data = 0xFF;
}
/* Wait until the transmit buffer is empty */
while ( SPI_I2S_GetFlagStatus( spi_mapping[spi->port].spi_regs, SPI_I2S_FLAG_TXE ) == RESET )
{}
/* Send the byte */
SPI_I2S_SendData( spi_mapping[spi->port].spi_regs, data );
/* Wait until a data is received */
while ( SPI_I2S_GetFlagStatus( spi_mapping[spi->port].spi_regs, SPI_I2S_FLAG_RXNE ) == RESET )
{}
/* Get the received data */
data = SPI_I2S_ReceiveData( spi_mapping[spi->port].spi_regs );
if ( rcv_ptr != NULL )
{
*rcv_ptr++ = (uint8_t)data;
}
}
}
else if ( spi->bits == 16 )
{
const uint16_t* send_ptr = (const uint16_t *) segments[i].tx_buffer;
uint16_t* rcv_ptr = (uint16_t *) segments[i].rx_buffer;
/* Check that the message length is a multiple of 2 */
if ( ( count % 2 ) == 0 )
{
result = kGeneralErr;
goto cleanup_transfer;
}
while ( count != 0)
{
uint16_t data = 0xFFFF;
count -= 2;
if ( send_ptr != NULL )
{
data = *send_ptr++;
}
/* Wait until the transmit buffer is empty */
while ( SPI_I2S_GetFlagStatus( spi_mapping[spi->port].spi_regs, SPI_I2S_FLAG_TXE ) == RESET )
{}
/* Send the byte */
SPI_I2S_SendData( spi_mapping[spi->port].spi_regs, data );
/* Wait until a data is received */
while ( SPI_I2S_GetFlagStatus( spi_mapping[spi->port].spi_regs, SPI_I2S_FLAG_RXNE ) == RESET )
{}
/* Get the received data */
data = SPI_I2S_ReceiveData( spi_mapping[spi->port].spi_regs );
if ( rcv_ptr != NULL )
{
*rcv_ptr++ = data;
}
}
}
}
}
cleanup_transfer:
MicoGpioOutputHigh(spi->chip_select);
MicoMcuPowerSaveConfig(true);
return result;
}
void init_platform_bootloader( void )
{
CRC8_Context crc;
OSStatus err = kNoErr;
mico_logic_partition_t *rf_partition = MicoFlashGetInfo( MICO_PARTITION_RF_FIRMWARE );
MicoGpioInitialize( (mico_gpio_t)MICO_SYS_LED, OUTPUT_PUSH_PULL );
MicoGpioOutputLow( (mico_gpio_t)MICO_SYS_LED );
MicoGpioInitialize( (mico_gpio_t)MICO_RF_LED, OUTPUT_OPEN_DRAIN_NO_PULL );
MicoGpioOutputHigh( (mico_gpio_t)MICO_RF_LED );
MicoGpioInitialize((mico_gpio_t)BOOT_SEL, INPUT_PULL_UP);
MicoGpioInitialize((mico_gpio_t)MFG_SEL, INPUT_PULL_UP);
#ifdef USE_MiCOKit_EXT
dc_motor_init( );
dc_motor_set( 0 );
rgb_led_init();
rgb_led_open(0, 0, 0);
#endif
/* Specific operations used in EMW3165 production */
#define NEED_RF_DRIVER_COPY_BASE ((uint32_t)0x08008000)
#define TEMP_RF_DRIVER_BASE ((uint32_t)0x08040000)
#define TEMP_RF_DRIVER_END ((uint32_t)0x0807FFFF)
const uint8_t isDriverNeedCopy = *(uint8_t *)(NEED_RF_DRIVER_COPY_BASE);
const uint32_t totalLength = rf_partition->partition_length;
const uint8_t crcResult = *(uint8_t *)(TEMP_RF_DRIVER_END);
uint8_t targetCrcResult = 0;
uint32_t copyLength;
uint32_t destStartAddress_tmp = rf_partition->partition_start_addr;
uint32_t sourceStartAddress_tmp = TEMP_RF_DRIVER_BASE;
uint32_t i;
if ( isDriverNeedCopy != 0x0 )
return;
platform_log( "Bootloader start to copy RF driver..." );
/* Copy RF driver to SPI flash */
err = platform_flash_init( &platform_flash_peripherals[ MICO_FLASH_SPI ] );
require_noerr(err, exit);
err = platform_flash_init( &platform_flash_peripherals[ MICO_FLASH_EMBEDDED ] );
require_noerr(err, exit);
err = platform_flash_erase( &platform_flash_peripherals[ MICO_FLASH_SPI ],
rf_partition->partition_start_addr, rf_partition->partition_start_addr + rf_partition->partition_length - 1 );
require_noerr(err, exit);
platform_log( "Time: %d", mico_get_time_no_os() );
for(i = 0; i <= totalLength/SizePerRW; i++){
if( i == totalLength/SizePerRW ){
if(totalLength%SizePerRW)
copyLength = totalLength%SizePerRW;
else
break;
}else{
copyLength = SizePerRW;
}
printf(".");
err = platform_flash_read( &platform_flash_peripherals[ MICO_FLASH_EMBEDDED ], &sourceStartAddress_tmp, data , copyLength );
require_noerr( err, exit );
err = platform_flash_write( &platform_flash_peripherals[ MICO_FLASH_SPI ], &destStartAddress_tmp, data, copyLength );
require_noerr(err, exit);
}
printf("\r\n");
/* Check CRC-8 check-sum */
platform_log( "Bootloader start to verify RF driver..." );
sourceStartAddress_tmp = TEMP_RF_DRIVER_BASE;
destStartAddress_tmp = rf_partition->partition_start_addr;
CRC8_Init( &crc );
for(i = 0; i <= totalLength/SizePerRW; i++){
if( i == totalLength/SizePerRW ){
if(totalLength%SizePerRW)
copyLength = totalLength%SizePerRW;
else
break;
}else{
copyLength = SizePerRW;
}
printf(".");
err = platform_flash_read( &platform_flash_peripherals[ MICO_FLASH_SPI ], &destStartAddress_tmp, data, copyLength );
require_noerr( err, exit );
CRC8_Update( &crc, data, copyLength);
}
CRC8_Final( &crc, &targetCrcResult );
printf("\r\n");
//require_string( crcResult == targetCrcResult, exit, "Check-sum error" );
if( crcResult != targetCrcResult ){
platform_log("Check-sum error");
while(1);
}
/* Clear RF driver from temperary storage */
platform_log("Bootloader start to clear RF driver temporary storage...");
/* Clear copy tag */
err = platform_flash_erase( &platform_flash_peripherals[ MICO_FLASH_EMBEDDED ], NEED_RF_DRIVER_COPY_BASE, NEED_RF_DRIVER_COPY_BASE);
require_noerr(err, exit);
exit:
return;
}
