void main (void)
{
/*
Define Variables ---------------------------------------------------------------------
*/
// I2C/MSG Q variables
char c; // Is this used?
signed char length;
unsigned char msgtype;
unsigned char last_reg_recvd;
i2c_comm ic;
//unsigned char msgbuffer[MSGLEN+1];
unsigned char msgbuffer[12];
unsigned char i;
int I2C_buffer[];
int index = 0;
int ITR = 0;
int I2C_RX_MSG_COUNT = 0;
int I2C_RX_MSG_PRECOUNT = 0;
int I2C_TX_MSG_COUNT = 1;
// Timer variables
timer1_thread_struct t1thread_data; // info for timer1_lthread
timer0_thread_struct t0thread_data; // info for timer0_lthread
int timer_on = 1;
int timer2Count0 = 0, timer2Count1 = 0;
// UART variables
uart_comm uc;
//uart_thread_struct uthread_data; // info for uart_lthread
// ADC variables
int ADCVALUE = 0;
int adc_counter = 0;
int adc_chan_num = 0;
int adcValue = 0;
int count = 0;
// MIDI variable
char notePlayed;
/*
Initialization ------------------------------------------------------------------------
*/
// Clock initialization
OSCCON = 0x7C; // 16 MHz // Use for internal oscillator
OSCTUNEbits.PLLEN = 1; // 4x the clock speed in the previous line
// UART initialization
init_uart_recv(&uc); // initialize my uart recv handling code
// configure the hardware USART device
Open2USART( USART_TX_INT_OFF & USART_RX_INT_OFF & USART_ASYNCH_MODE & USART_EIGHT_BIT &
USART_CONT_RX & USART_BRGH_LOW, 31);
Open1USART( USART_TX_INT_OFF & USART_RX_INT_ON & USART_ASYNCH_MODE & USART_EIGHT_BIT &
USART_CONT_RX & USART_BRGH_LOW, 51);
//RCSTA1bits.CREN = 1;
//RCSTA1bits.SPEN = 1;
//TXSTA1bits.SYNC = 0;
//PIE1bits.RC1IE = 1;
IPR1bits.RC1IP = 0;
// I2C/MSG Q initialization
init_i2c(&ic); // initialize the i2c code
init_queues(); // initialize message queues before enabling any interrupts
i2c_configure_slave(0x9E); // configure the hardware i2c device as a slave
// Timer initialization
init_timer1_lthread(&t1thread_data); // init the timer1 lthread
OpenTimer0( TIMER_INT_ON & T0_16BIT & T0_SOURCE_INT & T0_PS_1_8);
OpenTimer2( TIMER_INT_ON & T2_PS_1_16 /*& T2_8BIT_RW & T2_SOURCE_INT & T2_OSC1EN_OFF & T2_SYNC_EXT_OFF*/); // Turn Off
// ADC initialization
// set up PORTA for input
PORTA = 0x0; // clear the port
LATA = 0x0; // clear the output latch
TRISA = 0xFF; // set RA3-RA0 to inputs
ANSELA = 0xFF;
initADC();
// Interrupt initialization
// Peripheral interrupts can have their priority set to high or low
// enable high-priority interrupts and low-priority interrupts
enable_interrupts();
// Decide on the priority of the enabled peripheral interrupts, 0 is low 1 is high
IPR1bits.TMR1IP = 0; // Timer1 interrupt
//IPR1bits.RCIP = 0; // USART RX interrupt
IPR1bits.SSP1IP = 1; // I2C interrupt
PIE1bits.SSP1IE = 1; // must specifically enable the I2C interrupts
IPR1bits.ADIP = 1; // ADC interrupt WE ADDED THIS
// set direction for PORTB to output
TRISB = 0x0;
TRISD = 0xFF;
LATB = 0x0;
ANSELC = 0x00;
/*
Hand off messages to subroutines -----------------------------------------------------------
*/
// This loop is responsible for "handing off" messages to the subroutines
// that should get them. Although the subroutines are not threads, but
// they can be equated with the tasks in your task diagram if you
// structure them properly.
while (1) {
// Call a routine that blocks until either on the incoming
// messages queues has a message (this may put the processor into
// an idle mode
block_on_To_msgqueues();
/*
High Priority MSGQ ----------------------------------------------------------------------
*/
// At this point, one or both of the queues has a message. It
// makes sense to check the high-priority messages first -- in fact,
// you may only want to check the low-priority messages when there
// is not a high priority message. That is a design decision and
// I haven't done it here.
length = ToMainHigh_recvmsg(MSGLEN,&msgtype,(void *) msgbuffer);
if (length < 0) {
// no message, check the error code to see if it is concern
if (length != MSGQUEUE_EMPTY) {
//printf("Error: Bad high priority receive, code = %x\r\n", length);
}
} else {
switch (msgtype) {
case MSGT_ADC: {
// Format I2C msg
msgbuffer[6] = (timer2Count0 & 0x00FF);
msgbuffer[5] = (timer2Count0 & 0xFF00) >> 8;
msgbuffer[4] = (timer2Count1 & 0x00FF);
msgbuffer[3] = (timer2Count1 & 0xFF00) >> 8;
msgbuffer[8] = 0x00;
msgbuffer[10] = adc_chan_num;
msgbuffer[11] = 0xaa; // ADC MSG opcode
// Send I2C msg
FromMainHigh_sendmsg(12, msgtype, msgbuffer); // Send ADC msg to FromMainHigh MQ, which I2C
// int hdlr later Reads
// Increment I2C message count from 1 to 100
if(I2C_TX_MSG_COUNT < 100) {
I2C_TX_MSG_COUNT = I2C_TX_MSG_COUNT + 1;
}
else {
I2C_TX_MSG_COUNT = 1;
}
// Increment the channel number
if(adc_chan_num <= 4) adc_chan_num++;
else adc_chan_num = 0;
// Set ADC channel based off of channel number
if(adc_chan_num == 0) SetChanADC(ADC_CH0);
else if(adc_chan_num == 1) SetChanADC(ADC_CH1);
else if(adc_chan_num == 2) SetChanADC(ADC_CH2);
else if(adc_chan_num == 3) SetChanADC(ADC_CH3);
else if(adc_chan_num == 4) SetChanADC(ADC_CH4);
else SetChanADC(ADC_CH5);
};
case MSGT_TIMER0: {
timer0_lthread(&t0thread_data,msgtype,length,msgbuffer);
break;
};
case MSGT_TIMER2: {
timer2Count0++;
if(timer2Count0 >= 0xFFFF) {
timer2Count1++;
timer2Count0 = 0;
}
break;
}
case MSGT_I2C_DATA: { //this data still needs to be put in a buffer
;
if(msgbuffer[0] == 0xaf) {
//FromMainLow_sendmsg(5, msgtype, msgbuffer);
// The code below checks message 'counts' to see if any I2C messages were dropped
//I2C_RX_MSG_COUNT = msgbuffer[4];
FromMainLow_sendmsg(9, msgtype, msgbuffer);
TXSTA2bits.TXEN = 1;
/*
// Send note data to the MIDI device
//while(Busy2USART());
putc2USART(msgbuffer[1]);
//while(Busy2USART());
Delay1KTCYx(8);
putc2USART(msgbuffer[2]);
//while(Busy2USART());
Delay1KTCYx(8);
putc2USART(msgbuffer[3]);
*/
if(I2C_RX_MSG_COUNT - I2C_RX_MSG_PRECOUNT == 1) {
if(I2C_RX_MSG_PRECOUNT < 99) {
I2C_RX_MSG_PRECOUNT++;
}
else {
I2C_RX_MSG_PRECOUNT = 0;
}
}
else {
I2C_RX_MSG_PRECOUNT = I2C_RX_MSG_COUNT;
}
}
};
`
case MSGT_I2C_DBG: {
//printf("I2C Interrupt received %x: ",msgtype);
for (i=0;i<length;i++) {
//printf(" %x",msgbuffer[i]);
}
//printf("\r\n");
// keep track of the first byte received for later use
last_reg_recvd = msgbuffer[0];
break;
};
case MSGT_I2C_RQST: {
//printf("I2C Slave Req\r\n");
// The last byte received is the "register" that is trying to be read
// The response is dependent on the register.
switch (last_reg_recvd) {
case 0xaa: {
break;
}
/*
case 0xa8: {
length = 1;
msgbuffer[0] = 0x3A;
break;
}
case 0xa9: {
length = 1;
msgbuffer[0] = 0xA3;
break;
}*/
};
//start_i2c_slave_reply(length,msgbuffer);
break;
};
default: {
//printf("Error: Unexpected msg in queue, type = %x\r\n", msgtype);
break;
};
};
}
/*
Low Priority MSGQ -----------------------------------------------------------------------
*/
length = ToMainLow_recvmsg(MSGLEN,&msgtype,(void *) msgbuffer);
if (length < 0) {
// no message, check the error code to see if it is concern
if (length != MSGQUEUE_EMPTY) {
}
} else {
switch (msgtype) {
case MSGT_TIMER1: {
timer1_lthread(&t1thread_data,msgtype,length,msgbuffer);
break;
};
case MSGT_OVERRUN:
case MSGT_UART_DATA:
{
LATB = 0xFF;
msgbuffer[11] = 0xBB;
FromMainHigh_sendmsg(12, msgtype, msgbuffer);
break;
};
default: {
break;
};
};
}
}
int main(void)
#endif
{
BYTE i, j;
BYTE TxSynCount = 0;
BOOL bReceivedMessage = FALSE;
_U16 m;
#define BAUDRG 77
/*******************************************************************/
// Initialize the system
/*******************************************************************/
ANCON0 = 0XFF; /*desactiva entradas analogicas*/
ANCON1 = 0XFF; /*desactiva entradas analogicas*/
PPSUnLock();
PPSOutput(PPS_RP10, PPS_TX2CK2); // TX2 RP17/RC6
PPSInput(PPS_RX2DT2, PPS_RP9); // RX2 RP18/RC7
PPSOutput(PPS_RP23, PPS_SDO2); // SDO2 RP23/RD6
PPSInput(PPS_SDI2, PPS_RP24); // SDI2 RP24/RD7
PPSOutput(PPS_RP22, PPS_SCK2); // SCK2 RP22/RD5
PPSLock();
System_PeripheralPinSelect( ExternalInterrupt3, 19); /*external interrupt 3 B3*/
BoardInit();
ConsoleInit();
Open2USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud2USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
Gpios_PinDirection(GPIOS_PORTD, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTD, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
Gpios_PinDirection(GPIOS_PORTD, 5, GPIOS_OUTPUT); /*pin C2 como salida para SCK*/
Spi_Init(SPI_PORT1, SPI_64DIV); /*Inicializamos SPI2*/
Spi_Init(SPI_PORT2, SPI_64DIV); /*Inicializamos SPI2*/
//Spi_SetMode(SPI_PORT1, 1);
//Spi_SetMode(SPI_PORT1, 1);
LED_1 = 1;
LED_2 = 1;
Read_MAC_Address();
LED_1 = 0;
LED_2 = 0;
ConsolePutROMString((ROM char *)"\r\n<MAC Addr:");
PrintChar(myLongAddress[3]);
PrintChar(myLongAddress[2]);
PrintChar(myLongAddress[1]);
PrintChar(myLongAddress[0]);
ConsolePutROMString((ROM char *)"\r>");
Printf("\r\nStarting Testing Interface for MiWi(TM) PRO Stack ...");
#if defined(MRF24J40)
Printf("\r\n RF Transceiver: MRF24J40");
#elif defined(MRF49XA)
Printf("\r\n RF Transceiver: MRF49XA");
#elif defined(MRF89XA)
Printf("\r\n RF Transceiver: MRF89XA");
#endif
Printf("\r\n Demo Instruction:");
Printf("\r\n Press Enter to bring up the menu.");
Printf("\r\n Type in hyper terminal to choose");
Printf("\r\n menu item. ");
Printf("\r\n\r\n");
/*******************************************************************/
// Following block display demo information on LCD of Explore 16 or
// PIC18 Explorer demo board.
/*******************************************************************/
#if defined(MRF49XA)
LCDDisplay((char *)"MiWi PRO Test Interface MRF49XA", 0, TRUE);
#elif defined(MRF24J40)
LCDDisplay((char *)"MiWi PRO Test Interface MRF24J40", 0, TRUE);
#elif defined(MRF89XA)
LCDDisplay((char *)"MiWi PRO Test Interface MRF89XA", 0, TRUE);
#endif
//if( (PUSH_BUTTON_1 == 0) || ( MiApp_ProtocolInit(TRUE) == FALSE ) )
if (PUSH_BUTTON_1 == 1)
{
MiApp_ProtocolInit(FALSE);
LED_1 = 0;
LED_2 = 0;
#ifdef ENABLE_ACTIVE_SCAN
myChannel = 0xFF;
ConsolePutROMString((ROM char *)"\r\nStarting Active Scan...");
LCDDisplay((char *)"Active Scanning", 0, FALSE);
/*******************************************************************/
// Function MiApp_SearchConnection will return the number of
// existing connections in all channels. It will help to decide
// which channel to operate on and which connection to add.
// The return value is the number of connections. The connection
// data are stored in global variable ActiveScanResults.
// Maximum active scan result is defined as
// ACTIVE_SCAN_RESULT_SIZE
// The first parameter is the scan duration, which has the same
// definition in Energy Scan. 10 is roughly 1 second. 9 is a
// half second and 11 is 2 seconds. Maximum scan duration is 14,
// or roughly 16 seconds.
// The second parameter is the channel map. Bit 0 of the
// double word parameter represents channel 0. For the 2.4GHz
// frequency band, all possible channels are channel 11 to
// channel 26. As the result, the bit map is 0x07FFF800. Stack
// will filter out all invalid channels, so the application
// only needs to pay attention to the channels that are not
// preferred.
/*******************************************************************/
i = MiApp_SearchConnection(10, 0x02000000);
if( i > 0 )
{
// now print out the scan result.
Printf("\r\nActive Scan Results: \r\n");
for(j = 0; j < i; j++)
{
Printf("Channel: ");
PrintDec(ActiveScanResults[j].Channel );
Printf(" RSSI: ");
PrintChar(ActiveScanResults[j].RSSIValue);
Printf("\r\n");
myChannel = ActiveScanResults[j].Channel;
Printf("PeerInfo: ");
PrintChar( ActiveScanResults[j].PeerInfo[0]);
}
}
#endif
/*******************************************************************/
// Function MiApp_ConnectionMode sets the connection mode for the
// protocol stack. Possible connection modes are:
// - ENABLE_ALL_CONN accept all connection request
// - ENABLE_PREV_CONN accept only known device to connect
// - ENABL_ACTIVE_SCAN_RSP do not accept connection request, but
// allow response to active scan
// - DISABLE_ALL_CONN disable all connection request, including
// active scan request
/*******************************************************************/
MiApp_ConnectionMode(ENABLE_ALL_CONN);
if( i > 0 )
{
/*******************************************************************/
// Function MiApp_EstablishConnection try to establish a new
// connection with peer device.
// The first parameter is the index to the active scan result, which
// is acquired by discovery process (active scan). If the value
// of the index is 0xFF, try to establish a connection with any
// peer.
// The second parameter is the mode to establish connection, either
// direct or indirect. Direct mode means connection within the
// radio range; Indirect mode means connection may or may not
// in the radio range.
/*******************************************************************/
if( MiApp_EstablishConnection(0, CONN_MODE_DIRECT) == 0xFF )
{
Printf("\r\nJoin Fail");
}
}
else
{
/*******************************************************************/
// Function MiApp_StartConnection tries to start a new network
//
// The first parameter is the mode of start connection. There are
// two valid connection modes:
// - START_CONN_DIRECT start the connection on current
// channel
// - START_CONN_ENERGY_SCN perform an energy scan first,
// before starting the connection on
// the channel with least noise
// - START_CONN_CS_SCN perform a carrier sense scan
// first, before starting the
// connection on the channel with
// least carrier sense noise. Not
// supported on currrent radios
//
// The second parameter is the scan duration, which has the same
// definition in Energy Scan. 10 is roughly 1 second. 9 is a
// half second and 11 is 2 seconds. Maximum scan duration is
// 14, or roughly 16 seconds.
//
// The third parameter is the channel map. Bit 0 of the
// double word parameter represents channel 0. For the 2.4GHz
// frequency band, all possible channels are channel 11 to
// channel 26. As the result, the bit map is 0x07FFF800. Stack
// will filter out all invalid channels, so the application
// only needs to pay attention to the channels that are not
// preferred.
/*******************************************************************/
#ifdef ENABLE_ED_SCAN
//LCDDisplay((char *)"Active Scanning Energy Scanning", 0, FALSE);
ConsolePutROMString((ROM char *)"\r\nActive Scanning Energy Scanning");
MiApp_StartConnection(START_CONN_ENERGY_SCN, 10, 0x02000000);
#endif
}
// Turn on LED 1 to indicate ready to accept new connections
LED_1 = 1;
}
else
{
//LCDDisplay((char *)" Network Freezer ENABLED", 0, TRUE);
Printf("\r\nNetwork Freezer Feature is enabled. There will be no hand-shake process.\r\n");
LED_1 = 1;
DumpConnection(0xFF);
}
LCDDisplay((char *)"Start Connection on Channel %d", currentChannel, TRUE);
LCDDisplay((char *)"Testing Menu on Hyper Terminal", 0, FALSE);
while(1)
{
/*******************************************************************/
// Function MiApp_MessageAvailable will return a boolean to indicate
// if a message for application layer has been received by the
// transceiver. If a message has been received, all information will
// be stored in the rxMessage, structure of RECEIVED_MESSAGE.
/*******************************************************************/
if( MiApp_MessageAvailable() )
{
/*******************************************************************/
// If a packet has been received, following code prints out some of
// the information available in rxFrame.
/*******************************************************************/
if( rxMessage.flags.bits.secEn )
{
ConsolePutROMString((ROM char *)"Secured ");
}
if( rxMessage.flags.bits.broadcast )
{
ConsolePutROMString((ROM char *)"Broadcast Packet with RSSI ");
}
else
{
ConsolePutROMString((ROM char *)"Unicast Packet with RSSI ");
}
PrintChar(rxMessage.PacketRSSI);
if( rxMessage.flags.bits.srcPrsnt )
{
ConsolePutROMString((ROM char *)" from ");
if( rxMessage.flags.bits.altSrcAddr )
{
PrintChar(rxMessage.SourceAddress[1]);
PrintChar(rxMessage.SourceAddress[0]);
}
else
{
for(i = 0; i < MY_ADDRESS_LENGTH; i++)
{
PrintChar(rxMessage.SourceAddress[MY_ADDRESS_LENGTH-1-i]);
}
}
}
ConsolePutROMString((ROM char *)": ");
for(i = 0; i < rxMessage.PayloadSize; i++)
{
ConsolePut(rxMessage.Payload[i]);
}
// Toggle LED2 to indicate receiving a packet.
LED_2 ^= 1;
/*******************************************************************/
// Function MiApp_DiscardMessage is used to release the current
// received message. After calling this function, the stack can
// start to process the next received message.
/*******************************************************************/
MiApp_DiscardMessage();
bReceivedMessage = TRUE;
/*******************************************************************/
// Following block update the total received and transmitted messages
// on the LCD of the demo board.
/*******************************************************************/
LCDTRXCount(TxNum, ++RxNum);
}
else
{
++m;
if(m > 8000)
{
m=0;
//LED_1 ^= 1;
MiApp_FlushTx();
MiApp_WriteData('H');
MiApp_WriteData('o');
MiApp_WriteData('l');
MiApp_WriteData('a');
MiApp_WriteData('a');
MiApp_WriteData('a');
MiApp_WriteData(0x0D);
MiApp_WriteData(0x0A);
MiApp_BroadcastPacket(FALSE);
}
if ( ConsoleIsGetReady() )
{
//ProcessMenu();
}
}
}
}
void main(void)
{
#define BAUDRG 77
BYTE SecNum = 0;
BOOL Tx_Success = FALSE;
BYTE Tx_Trials = 0, scanresult = 0;
/*******************************************************************/
// Initialize the system
/*******************************************************************/
ANCON0 = 0XFF; /*desactiva entradas analogicas*/
ANCON1 = 0XFF; /*desactiva entradas analogicas*/
PPSUnLock();
PPSOutput(PPS_RP10, PPS_TX2CK2); // TX2 RP17/RC6 icsp
PPSInput(PPS_RX2DT2, PPS_RP9); // RX2 RP18/RC7
PPSOutput(PPS_RP23, PPS_SDO2); // SDO2 RP23/RD6
PPSInput(PPS_SDI2, PPS_RP24); // SDI2 RP24/RD7
PPSOutput(PPS_RP22, PPS_SCK2); // SCK2 RP22/RD5
PPSLock();
System_PeripheralPinSelect( ExternalInterrupt3, 19); /*external interrupt 3 B3*/
BoardInit();
ConsoleInit();
Gpios_PinDirection(GPIOS_PORTC, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTC, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
//Gpios_PinDirection(GPIOS_PORTD, 4, GPIOS_OUTPUT); /*pin D4 como salida */
Open1USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud1USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
Open2USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud2USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
OpenTimer1( TIMER_INT_OFF &T1_16BIT_RW &T1_SOURCE_FOSC_4 & T1_PS_1_8 &T1_OSC1EN_OFF &T1_SYNC_EXT_OFF, TIMER_GATE_OFF & TIMER_GATE_INT_OFF);
Gpios_PinDirection(GPIOS_PORTD, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTD, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
Gpios_PinDirection(GPIOS_PORTD, 5, GPIOS_OUTPUT); /*pin C2 como salida para SCK*/
Spi_Init(SPI_PORT1, SPI_64DIV); /*Inicializamos SPI2*/
Spi_Init(SPI_PORT2, SPI_64DIV); /*Inicializamos SPI2*/
//Adc_Init(ADC_10BITS);
LED_1 = 1;
LED_2 = 0;
//RLY_1 = 0;
RLY_2 = 0;
ON_RADIO = 1;
ON_MAC = 1;
ON_TEMP = 1;
StartWirelessConnection();
//myDevicesRequiredStatus[0] = 0x55;
EEPROMRead(&myDevicesRequiredStatus, 0, 1);
if(myDevicesRequiredStatus[0] == 0x55)
{
RLY_1 = 1;
EEPROMCHG = 1;
ConsolePutROMString((ROM char *)"RELAY ON ");
}
if(myDevicesRequiredStatus[0] == 0xAA)
{
RLY_1 = 0;
EEPROMCHG = 0;
ConsolePutROMString((ROM char *)"RELAY OFF ");
}
for(j=0;j<10;j++)
{
DelayMs(50);
LED_1 ^= 1;
LED_2 ^= 1;
}
LED_1 = 0;
LED_2 = 0;
//RLY_1 = 0;
RLY_2 = 0;
TickScaler = 4;
EndDevStateMachine =0;
/*
while(!Tx_Success)
{
if(myChannel < 8)
scanresult = MiApp_SearchConnection(10, (0x00000001 << myChannel));
else if(myChannel < 16)
scanresult = MiApp_SearchConnection(10, (0x00000100 << (myChannel-8)));
else if(myChannel < 24)
scanresult = MiApp_SearchConnection(10, (0x00010000 << (myChannel-16)));
else
scanresult = MiApp_SearchConnection(10, (0x01000000 << (myChannel-24)));
if(scanresult == 0)
{
Tx_Trials++;
if(Tx_Trials > 2) break;
}
else Tx_Success = TRUE;
}
if(Tx_Success)
{
ConsolePutROMString((ROM char *)"RADIO OK ");
}
else
{
ConsolePutROMString((ROM char *)"RADIO FAIL ");
}
*/
//.VBGOE = 0;
//ANCON1bits.VBGEN = 1; // Enable Band gap reference voltage
//DelayMs(10);
//VBGResult = Adc_u16Read(15);
//ANCON1bits.VBGEN = 0; // Disable Bandgap
//Adc_Init(ADC_10BITS);
ANCON0 = 0xFF;
ANCON1 = 0x9F;
ANCON1bits.VBGEN = 1; // Enable Band gap reference voltage
ADCON0bits.VCFG = 0; // vreff VDD-VSS
ADCON0bits.CHS = 0x0F; // VBG channel select
ADCON1 = 0xBE;
ADCON0bits.ADON = 1;
//for(j=0;j<16;j++)
//{
//myDevicesOutputStatus[j] = j;
//}
//EEPROMWRITE(myDevicesOutputStatus,0,16);
//for(j=0;j<16;j++)
//{
//myDevicesOutputStatus[j] = 0;
//}
//DelayMs(500);
EEPROMRead(&myDevicesOutputStatus, 0, 16);
ConsolePutROMString((ROM char *)"EEPROM READ: ");
//PrintChar(TemperatureCalibrationValue);
for(j=0;j<1;j++)
{
PrintChar(myDevicesOutputStatus[j]);
}
SwTimer3 = 0;
SwTimer4 = 0;
TRISB&=0xEF; //JL: Configuro el pin B4 como salida si modificar el estado de los demas pines
while(1)
{
/*
WirelessTxRx();
WirelesStatus();
Bypass();
*/
//No se utilizaron
//Menu();
//Timer1Tick();
//WirelessTxRxPANCOORD();
//TaskScheduler();
//JLEstas funciones deben habilitarse para trabajar como repetidora
Timer1Tick();
Repeater();
}
}
