/**
* @brief Initialize the MPU6000 3-axis gyro sensor
* \return none
* \param[in] PIOS_MPU6000_ConfigTypeDef struct to be used to configure sensor.
*
*/
static void PIOS_MPU6000_Config(struct pios_mpu6000_cfg const *cfg)
{
PIOS_MPU6000_Test();
// Reset chip
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_PWR_MGMT_REG, PIOS_MPU6000_PWRMGMT_IMU_RST) != 0) {
;
}
PIOS_DELAY_WaitmS(50);
// Reset chip and fifo
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_USER_CTRL_REG,
PIOS_MPU6000_USERCTL_GYRO_RST |
PIOS_MPU6000_USERCTL_SIG_COND |
PIOS_MPU6000_USERCTL_FIFO_RST) != 0) {
;
}
// Wait for reset to finish
while (PIOS_MPU6000_GetReg(PIOS_MPU6000_USER_CTRL_REG) &
(PIOS_MPU6000_USERCTL_GYRO_RST |
PIOS_MPU6000_USERCTL_SIG_COND |
PIOS_MPU6000_USERCTL_FIFO_RST)) {
;
}
PIOS_DELAY_WaitmS(10);
// Power management configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_PWR_MGMT_REG, cfg->Pwr_mgmt_clk) != 0) {
;
}
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_INT_CFG_REG, cfg->interrupt_cfg) != 0) {
;
}
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_INT_EN_REG, cfg->interrupt_en) != 0) {
;
}
// FIFO storage
#if defined(PIOS_MPU6000_ACCEL)
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_FIFO_EN_REG, cfg->Fifo_store | PIOS_MPU6000_ACCEL_OUT) != 0) {
;
}
#else
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_FIFO_EN_REG, cfg->Fifo_store) != 0) {
;
}
#endif
PIOS_MPU6000_ConfigureRanges(cfg->gyro_range, cfg->accel_range, cfg->filter);
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_USER_CTRL_REG, cfg->User_ctl) != 0) {
;
}
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_PWR_MGMT_REG, cfg->Pwr_mgmt_clk) != 0) {
;
}
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_INT_CFG_REG, cfg->interrupt_cfg) != 0) {
;
}
// Interrupt configuration
while (PIOS_MPU6000_SetReg(PIOS_MPU6000_INT_EN_REG, cfg->interrupt_en) != 0) {
;
}
if ((PIOS_MPU6000_GetReg(PIOS_MPU6000_INT_EN_REG)) != cfg->interrupt_en) {
return;
}
mpu6000_configured = true;
}
void PIOS_Board_Init(void) {
/* Delay system */
PIOS_DELAY_Init();
const struct pios_board_info * bdinfo = &pios_board_info_blob;
#if defined(PIOS_INCLUDE_LED)
const struct pios_led_cfg * led_cfg = PIOS_BOARD_HW_DEFS_GetLedCfg(bdinfo->board_rev);
PIOS_Assert(led_cfg);
PIOS_LED_Init(led_cfg);
#endif /* PIOS_INCLUDE_LED */
/* Set up the SPI interface to the gyro/acelerometer */
if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) {
PIOS_DEBUG_Assert(0);
}
/* Set up the SPI interface to the flash and rfm22b */
if (PIOS_SPI_Init(&pios_spi_telem_flash_id, &pios_spi_telem_flash_cfg)) {
PIOS_DEBUG_Assert(0);
}
#if defined(PIOS_INCLUDE_FLASH)
/* Connect flash to the approrpiate interface and configure it */
uintptr_t flash_id;
if (PIOS_Flash_Jedec_Init(&flash_id, pios_spi_telem_flash_id, 1, &flash_m25p_cfg) != 0)
panic(1);
uintptr_t fs_id;
if (PIOS_FLASHFS_Logfs_Init(&fs_id, &flashfs_m25p_cfg, &pios_jedec_flash_driver, flash_id) != 0)
panic(1);
#endif
/* Initialize UAVObject libraries */
EventDispatcherInitialize();
UAVObjInitialize();
HwFreedomInitialize();
ModuleSettingsInitialize();
#if defined(PIOS_INCLUDE_RTC)
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
/* Initialize the alarms library */
AlarmsInitialize();
/* Initialize the task monitor library */
TaskMonitorInitialize();
// /* Set up pulse timers */
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_2_cfg);
PIOS_TIM_InitClock(&tim_3_cfg);
/* IAP System Setup */
PIOS_IAP_Init();
uint16_t boot_count = PIOS_IAP_ReadBootCount();
if (boot_count < 3) {
PIOS_IAP_WriteBootCount(++boot_count);
AlarmsClear(SYSTEMALARMS_ALARM_BOOTFAULT);
} else {
/* Too many failed boot attempts, force hw config to defaults */
HwFreedomSetDefaults(HwFreedomHandle(), 0);
ModuleSettingsSetDefaults(ModuleSettingsHandle(),0);
AlarmsSet(SYSTEMALARMS_ALARM_BOOTFAULT, SYSTEMALARMS_ALARM_CRITICAL);
}
PIOS_IAP_Init();
#if defined(PIOS_INCLUDE_USB)
/* Initialize board specific USB data */
PIOS_USB_BOARD_DATA_Init();
/* Flags to determine if various USB interfaces are advertised */
bool usb_hid_present = false;
bool usb_cdc_present = false;
#if defined(PIOS_INCLUDE_USB_CDC)
if (PIOS_USB_DESC_HID_CDC_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
usb_cdc_present = true;
#else
if (PIOS_USB_DESC_HID_ONLY_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
#endif
uint32_t pios_usb_id;
PIOS_USB_Init(&pios_usb_id, PIOS_BOARD_HW_DEFS_GetUsbCfg(bdinfo->board_rev));
#if defined(PIOS_INCLUDE_USB_CDC)
uint8_t hw_usb_vcpport;
/* Configure the USB VCP port */
HwFreedomUSB_VCPPortGet(&hw_usb_vcpport);
if (!usb_cdc_present) {
/* Force VCP port function to disabled if we haven't advertised VCP in our USB descriptor */
hw_usb_vcpport = HWFREEDOM_USB_VCPPORT_DISABLED;
}
switch (hw_usb_vcpport) {
case HWFREEDOM_USB_VCPPORT_DISABLED:
break;
case HWFREEDOM_USB_VCPPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usb_cdc_cfg, PIOS_COM_TELEM_USB_RX_BUF_LEN, PIOS_COM_TELEM_USB_TX_BUF_LEN, &pios_usb_cdc_com_driver, &pios_com_telem_usb_id);
#endif /* PIOS_INCLUDE_COM */
break;
case HWFREEDOM_USB_VCPPORT_COMBRIDGE:
#if defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usb_cdc_cfg, PIOS_COM_BRIDGE_RX_BUF_LEN, PIOS_COM_BRIDGE_TX_BUF_LEN, &pios_usb_cdc_com_driver, &pios_com_vcp_id);
#endif /* PIOS_INCLUDE_COM */
break;
case HWFREEDOM_USB_VCPPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uint32_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_debug_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
NULL, 0,
tx_buffer, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_CDC */
#if defined(PIOS_INCLUDE_USB_HID)
/* Configure the usb HID port */
uint8_t hw_usb_hidport;
HwFreedomUSB_HIDPortGet(&hw_usb_hidport);
if (!usb_hid_present) {
/* Force HID port function to disabled if we haven't advertised HID in our USB descriptor */
hw_usb_hidport = HWFREEDOM_USB_HIDPORT_DISABLED;
}
switch (hw_usb_hidport) {
case HWFREEDOM_USB_HIDPORT_DISABLED:
break;
case HWFREEDOM_USB_HIDPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint32_t pios_usb_hid_id;
if (PIOS_USB_HID_Init(&pios_usb_hid_id, &pios_usb_hid_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_hid_com_driver, pios_usb_hid_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_HID */
if (usb_hid_present || usb_cdc_present) {
PIOS_USBHOOK_Activate();
}
#endif /* PIOS_INCLUDE_USB */
/* Configure IO ports */
uint8_t hw_DSMxBind;
HwFreedomDSMxBindGet(&hw_DSMxBind);
/* Configure FlexiPort */
uint8_t hw_mainport;
HwFreedomMainPortGet(&hw_mainport);
switch (hw_mainport) {
case HWFREEDOM_MAINPORT_DISABLED:
break;
case HWFREEDOM_MAINPORT_TELEMETRY:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_TELEM_RF_RX_BUF_LEN, PIOS_COM_TELEM_RF_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_telem_rf_id);
break;
break;
case HWFREEDOM_MAINPORT_GPS:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_GPS_RX_BUF_LEN, -1, &pios_usart_com_driver, &pios_com_gps_id);
break;
case HWFREEDOM_MAINPORT_DSM2:
case HWFREEDOM_MAINPORT_DSMX10BIT:
case HWFREEDOM_MAINPORT_DSMX11BIT:
{
enum pios_dsm_proto proto;
switch (hw_mainport) {
case HWFREEDOM_MAINPORT_DSM2:
proto = PIOS_DSM_PROTO_DSM2;
break;
case HWFREEDOM_MAINPORT_DSMX10BIT:
proto = PIOS_DSM_PROTO_DSMX10BIT;
break;
case HWFREEDOM_MAINPORT_DSMX11BIT:
proto = PIOS_DSM_PROTO_DSMX11BIT;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_dsm(&pios_usart_dsm_main_cfg, &pios_dsm_main_cfg,
&pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMMAINPORT,&hw_DSMxBind);
}
break;
case HWFREEDOM_MAINPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
PIOS_Board_configure_com(&pios_usart_main_cfg, 0, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_aux_id);
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWFREEDOM_MAINPORT_COMBRIDGE:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_BRIDGE_RX_BUF_LEN, PIOS_COM_BRIDGE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_bridge_id);
break;
} /* hw_freedom_mainport */
/* Configure flexi USART port */
uint8_t hw_flexiport;
HwFreedomFlexiPortGet(&hw_flexiport);
switch (hw_flexiport) {
case HWFREEDOM_FLEXIPORT_DISABLED:
break;
case HWFREEDOM_FLEXIPORT_TELEMETRY:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_TELEM_RF_RX_BUF_LEN, PIOS_COM_TELEM_RF_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_telem_rf_id);
break;
case HWFREEDOM_FLEXIPORT_GPS:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_GPS_RX_BUF_LEN, -1, &pios_usart_com_driver, &pios_com_gps_id);
break;
case HWFREEDOM_FLEXIPORT_DSM2:
case HWFREEDOM_FLEXIPORT_DSMX10BIT:
case HWFREEDOM_FLEXIPORT_DSMX11BIT:
{
enum pios_dsm_proto proto;
switch (hw_flexiport) {
case HWFREEDOM_FLEXIPORT_DSM2:
proto = PIOS_DSM_PROTO_DSM2;
break;
case HWFREEDOM_FLEXIPORT_DSMX10BIT:
proto = PIOS_DSM_PROTO_DSMX10BIT;
break;
case HWFREEDOM_FLEXIPORT_DSMX11BIT:
proto = PIOS_DSM_PROTO_DSMX11BIT;
break;
default:
PIOS_Assert(0);
break;
}
//TODO: Define the various Channelgroup for Revo dsm inputs and handle here
PIOS_Board_configure_dsm(&pios_usart_dsm_flexi_cfg, &pios_dsm_flexi_cfg,
&pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMFLEXIPORT,&hw_DSMxBind);
}
break;
case HWFREEDOM_FLEXIPORT_I2C:
#if defined(PIOS_INCLUDE_I2C)
{
if (PIOS_I2C_Init(&pios_i2c_flexiport_adapter_id, &pios_i2c_flexiport_adapter_cfg)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_I2C */
case HWFREEDOM_FLEXIPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
PIOS_Board_configure_com(&pios_usart_flexi_cfg, 0, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_aux_id);
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWFREEDOM_FLEXIPORT_COMBRIDGE:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_BRIDGE_RX_BUF_LEN, PIOS_COM_BRIDGE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_bridge_id);
break;
} /* hw_freedom_flexiport */
/* Initalize the RFM22B radio COM device. */
#if defined(PIOS_INCLUDE_RFM22B)
uint8_t hwsettings_radioport;
HwFreedomRadioPortGet(&hwsettings_radioport);
switch (hwsettings_radioport) {
case HWFREEDOM_RADIOPORT_DISABLED:
break;
case HWFREEDOM_RADIOPORT_TELEMETRY:
{
const struct pios_board_info * bdinfo = &pios_board_info_blob;
const struct pios_rfm22b_cfg *pios_rfm22b_cfg = PIOS_BOARD_HW_DEFS_GetRfm22Cfg(bdinfo->board_rev);
if (PIOS_RFM22B_Init(&pios_rfm22b_id, PIOS_RFM22_SPI_PORT, pios_rfm22b_cfg->slave_num, pios_rfm22b_cfg)) {
PIOS_Assert(0);
}
uint8_t *rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_RFM22B_RF_RX_BUF_LEN);
uint8_t *tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_RFM22B_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_rfm22b_com_driver, pios_rfm22b_id,
rx_buffer, PIOS_COM_RFM22B_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_RFM22B_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
break;
}
}
#endif /* PIOS_INCLUDE_RFM22B */
/* Configure input receiver USART port */
uint8_t hw_rcvrport;
HwFreedomRcvrPortGet(&hw_rcvrport);
switch (hw_rcvrport) {
case HWFREEDOM_RCVRPORT_DISABLED:
break;
case HWFREEDOM_RCVRPORT_PPM:
{
uint32_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uint32_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
break;
case HWFREEDOM_RCVRPORT_DSM2:
case HWFREEDOM_RCVRPORT_DSMX10BIT:
case HWFREEDOM_RCVRPORT_DSMX11BIT:
{
enum pios_dsm_proto proto;
switch (hw_rcvrport) {
case HWFREEDOM_RCVRPORT_DSM2:
proto = PIOS_DSM_PROTO_DSM2;
break;
case HWFREEDOM_RCVRPORT_DSMX10BIT:
proto = PIOS_DSM_PROTO_DSMX10BIT;
break;
case HWFREEDOM_RCVRPORT_DSMX11BIT:
proto = PIOS_DSM_PROTO_DSMX11BIT;
break;
default:
PIOS_Assert(0);
break;
}
//TODO: Define the various Channelgroup for Revo dsm inputs and handle here
PIOS_Board_configure_dsm(&pios_usart_dsm_rcvr_cfg, &pios_dsm_rcvr_cfg,
&pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMFLEXIPORT,&hw_DSMxBind);
}
break;
case HWFREEDOM_RCVRPORT_SBUS:
#if defined(PIOS_INCLUDE_SBUS)
{
uint32_t pios_usart_sbus_id;
if (PIOS_USART_Init(&pios_usart_sbus_id, &pios_usart_sbus_rcvr_cfg)) {
PIOS_Assert(0);
}
uint32_t pios_sbus_id;
if (PIOS_SBus_Init(&pios_sbus_id, &pios_sbus_cfg, &pios_usart_com_driver, pios_usart_sbus_id)) {
PIOS_Assert(0);
}
uint32_t pios_sbus_rcvr_id;
if (PIOS_RCVR_Init(&pios_sbus_rcvr_id, &pios_sbus_rcvr_driver, pios_sbus_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_SBUS] = pios_sbus_rcvr_id;
}
#endif
break;
}
if (hw_rcvrport != HWFREEDOM_RCVRPORT_SBUS) {
GPIO_Init(pios_sbus_cfg.inv.gpio, (GPIO_InitTypeDef*)&pios_sbus_cfg.inv.init);
GPIO_WriteBit(pios_sbus_cfg.inv.gpio, pios_sbus_cfg.inv.init.GPIO_Pin, pios_sbus_cfg.gpio_inv_disable);
}
#if defined(PIOS_OVERO_SPI)
/* Set up the SPI based PIOS_COM interface to the overo */
{
bool overo_enabled = false;
#ifdef MODULE_OveroSync_BUILTIN
overo_enabled = true;
#else
uint8_t module_state[MODULESETTINGS_ADMINSTATE_NUMELEM];
ModuleSettingsAdminStateGet(module_state);
if (module_state[MODULESETTINGS_ADMINSTATE_OVEROSYNC] == MODULESETTINGS_ADMINSTATE_ENABLED) {
overo_enabled = true;
} else {
overo_enabled = false;
}
#endif
if (overo_enabled) {
if (PIOS_OVERO_Init(&pios_overo_id, &pios_overo_cfg)) {
PIOS_DEBUG_Assert(0);
}
const uint32_t PACKET_SIZE = 1024;
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PACKET_SIZE);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PACKET_SIZE);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_overo_id, &pios_overo_com_driver, pios_overo_id,
rx_buffer, PACKET_SIZE,
tx_buffer, PACKET_SIZE)) {
PIOS_Assert(0);
}
}
}
#endif
#if defined(PIOS_INCLUDE_GCSRCVR)
GCSReceiverInitialize();
uint32_t pios_gcsrcvr_id;
PIOS_GCSRCVR_Init(&pios_gcsrcvr_id);
uint32_t pios_gcsrcvr_rcvr_id;
if (PIOS_RCVR_Init(&pios_gcsrcvr_rcvr_id, &pios_gcsrcvr_rcvr_driver, pios_gcsrcvr_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_GCS] = pios_gcsrcvr_rcvr_id;
#endif /* PIOS_INCLUDE_GCSRCVR */
#ifndef PIOS_DEBUG_ENABLE_DEBUG_PINS
uint8_t hw_output_port;
HwFreedomOutputGet(&hw_output_port);
switch (hw_output_port) {
case HWFREEDOM_OUTPUT_DISABLED:
break;
case HWFREEDOM_OUTPUT_PWM:
/* Set up the servo outputs */
PIOS_Servo_Init(&pios_servo_cfg);
break;
default:
break;
}
#else
PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels));
#endif
PIOS_DELAY_WaitmS(200);
PIOS_SENSORS_Init();
#if defined(PIOS_INCLUDE_MPU6000)
if (PIOS_MPU6000_Init(pios_spi_gyro_id,0, &pios_mpu6000_cfg) != 0)
panic(2);
if (PIOS_MPU6000_Test() != 0)
panic(2);
// To be safe map from UAVO enum to driver enum
uint8_t hw_gyro_range;
HwFreedomGyroRangeGet(&hw_gyro_range);
switch(hw_gyro_range) {
case HWFREEDOM_GYRORANGE_250:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_250_DEG);
break;
case HWFREEDOM_GYRORANGE_500:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_500_DEG);
break;
case HWFREEDOM_GYRORANGE_1000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_1000_DEG);
break;
case HWFREEDOM_GYRORANGE_2000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_2000_DEG);
break;
}
uint8_t hw_accel_range;
HwFreedomAccelRangeGet(&hw_accel_range);
switch(hw_accel_range) {
case HWFREEDOM_ACCELRANGE_2G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_2G);
break;
case HWFREEDOM_ACCELRANGE_4G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_4G);
break;
case HWFREEDOM_ACCELRANGE_8G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_8G);
break;
case HWFREEDOM_ACCELRANGE_16G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_16G);
break;
}
uint8_t hw_mpu6000_rate;
HwFreedomMPU6000RateGet(&hw_mpu6000_rate);
uint16_t hw_mpu6000_divisor = \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_500) ? 15 : \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_666) ? 11 : \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_1000) ? 7 : \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_2000) ? 3 : \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_4000) ? 1 : \
(hw_mpu6000_rate == HWFREEDOM_MPU6000RATE_8000) ? 0 : \
15;
PIOS_MPU6000_SetDivisor(hw_mpu6000_divisor);
uint8_t hw_dlpf;
HwFreedomMPU6000DLPFGet(&hw_dlpf);
uint16_t hw_mpu6000_dlpf = \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_256) ? PIOS_MPU60X0_LOWPASS_256_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_188) ? PIOS_MPU60X0_LOWPASS_188_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_98) ? PIOS_MPU60X0_LOWPASS_98_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_42) ? PIOS_MPU60X0_LOWPASS_42_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_20) ? PIOS_MPU60X0_LOWPASS_20_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_10) ? PIOS_MPU60X0_LOWPASS_10_HZ : \
(hw_dlpf == HWFREEDOM_MPU6000DLPF_5) ? PIOS_MPU60X0_LOWPASS_5_HZ : \
PIOS_MPU60X0_LOWPASS_256_HZ;
PIOS_MPU6000_SetLPF(hw_mpu6000_dlpf);
#endif
if (PIOS_I2C_Init(&pios_i2c_mag_pressure_adapter_id, &pios_i2c_mag_pressure_adapter_cfg)) {
PIOS_DEBUG_Assert(0);
}
if (PIOS_I2C_CheckClear(pios_i2c_mag_pressure_adapter_id) != 0)
panic(5);
PIOS_DELAY_WaitmS(50);
#if defined(PIOS_INCLUDE_ADC)
PIOS_ADC_Init(&pios_adc_cfg);
#endif
PIOS_LED_On(0);
#if defined(PIOS_INCLUDE_HMC5883)
if (PIOS_HMC5883_Init(pios_i2c_mag_pressure_adapter_id, &pios_hmc5883_cfg) != 0)
panic(3);
#endif
PIOS_LED_On(1);
#if defined(PIOS_INCLUDE_MS5611)
if (PIOS_MS5611_Init(&pios_ms5611_cfg, pios_i2c_mag_pressure_adapter_id) != 0)
panic(4);
#endif
PIOS_LED_On(2);
}
static void SensorsTask(void *parameters)
{
portTickType lastSysTime;
uint32_t accel_samples = 0;
uint32_t gyro_samples = 0;
int32_t accel_accum[3] = {0, 0, 0};
int32_t gyro_accum[3] = {0,0,0};
float gyro_scaling = 0;
float accel_scaling = 0;
static int32_t timeval;
AlarmsClear(SYSTEMALARMS_ALARM_SENSORS);
UAVObjEvent ev;
settingsUpdatedCb(&ev);
const struct pios_board_info * bdinfo = &pios_board_info_blob;
switch(bdinfo->board_rev) {
case 0x01:
#if defined(PIOS_INCLUDE_L3GD20)
gyro_test = PIOS_L3GD20_Test();
#endif
#if defined(PIOS_INCLUDE_BMA180)
accel_test = PIOS_BMA180_Test();
#endif
break;
case 0x02:
#if defined(PIOS_INCLUDE_MPU6000)
gyro_test = PIOS_MPU6000_Test();
accel_test = gyro_test;
#endif
break;
default:
PIOS_DEBUG_Assert(0);
}
#if defined(PIOS_INCLUDE_HMC5883)
mag_test = PIOS_HMC5883_Test();
#else
mag_test = 0;
#endif
if(accel_test < 0 || gyro_test < 0 || mag_test < 0) {
AlarmsSet(SYSTEMALARMS_ALARM_SENSORS, SYSTEMALARMS_ALARM_CRITICAL);
while(1) {
PIOS_WDG_UpdateFlag(PIOS_WDG_SENSORS);
vTaskDelay(10);
}
}
// Main task loop
lastSysTime = xTaskGetTickCount();
bool error = false;
uint32_t mag_update_time = PIOS_DELAY_GetRaw();
while (1) {
// TODO: add timeouts to the sensor reads and set an error if the fail
sensor_dt_us = PIOS_DELAY_DiffuS(timeval);
timeval = PIOS_DELAY_GetRaw();
if (error) {
PIOS_WDG_UpdateFlag(PIOS_WDG_SENSORS);
lastSysTime = xTaskGetTickCount();
vTaskDelayUntil(&lastSysTime, SENSOR_PERIOD / portTICK_RATE_MS);
AlarmsSet(SYSTEMALARMS_ALARM_SENSORS, SYSTEMALARMS_ALARM_CRITICAL);
error = false;
} else {
AlarmsClear(SYSTEMALARMS_ALARM_SENSORS);
}
for (int i = 0; i < 3; i++) {
accel_accum[i] = 0;
gyro_accum[i] = 0;
}
accel_samples = 0;
gyro_samples = 0;
AccelsData accelsData;
GyrosData gyrosData;
switch(bdinfo->board_rev) {
case 0x01: // L3GD20 + BMA180 board
#if defined(PIOS_INCLUDE_BMA180)
{
struct pios_bma180_data accel;
int32_t read_good;
int32_t count;
count = 0;
while((read_good = PIOS_BMA180_ReadFifo(&accel)) != 0 && !error)
error = ((xTaskGetTickCount() - lastSysTime) > SENSOR_PERIOD) ? true : error;
if (error) {
// Unfortunately if the BMA180 ever misses getting read, then it will not
// trigger more interrupts. In this case we must force a read to kickstarts
// it.
struct pios_bma180_data data;
PIOS_BMA180_ReadAccels(&data);
continue;
}
while(read_good == 0) {
count++;
accel_accum[1] += accel.x;
accel_accum[0] += accel.y;
accel_accum[2] -= accel.z;
read_good = PIOS_BMA180_ReadFifo(&accel);
}
accel_samples = count;
accel_scaling = PIOS_BMA180_GetScale();
// Get temp from last reading
accelsData.temperature = 25.0f + ((float) accel.temperature - 2.0f) / 2.0f;
}
#endif
#if defined(PIOS_INCLUDE_L3GD20)
{
struct pios_l3gd20_data gyro;
gyro_samples = 0;
xQueueHandle gyro_queue = PIOS_L3GD20_GetQueue();
if(xQueueReceive(gyro_queue, (void *) &gyro, 4) == errQUEUE_EMPTY) {
error = true;
continue;
}
gyro_samples = 1;
gyro_accum[1] += gyro.gyro_x;
gyro_accum[0] += gyro.gyro_y;
gyro_accum[2] -= gyro.gyro_z;
gyro_scaling = PIOS_L3GD20_GetScale();
// Get temp from last reading
gyrosData.temperature = gyro.temperature;
}
#endif
break;
case 0x02: // MPU6000 board
case 0x03: // MPU6000 board
#if defined(PIOS_INCLUDE_MPU6000)
{
struct pios_mpu6000_data mpu6000_data;
xQueueHandle queue = PIOS_MPU6000_GetQueue();
while(xQueueReceive(queue, (void *) &mpu6000_data, gyro_samples == 0 ? 10 : 0) != errQUEUE_EMPTY)
{
gyro_accum[0] += mpu6000_data.gyro_x;
gyro_accum[1] += mpu6000_data.gyro_y;
gyro_accum[2] += mpu6000_data.gyro_z;
accel_accum[0] += mpu6000_data.accel_x;
accel_accum[1] += mpu6000_data.accel_y;
accel_accum[2] += mpu6000_data.accel_z;
gyro_samples ++;
accel_samples ++;
}
if (gyro_samples == 0) {
PIOS_MPU6000_ReadGyros(&mpu6000_data);
error = true;
continue;
}
gyro_scaling = PIOS_MPU6000_GetScale();
accel_scaling = PIOS_MPU6000_GetAccelScale();
gyrosData.temperature = 35.0f + ((float) mpu6000_data.temperature + 512.0f) / 340.0f;
accelsData.temperature = 35.0f + ((float) mpu6000_data.temperature + 512.0f) / 340.0f;
}
#endif /* PIOS_INCLUDE_MPU6000 */
break;
default:
PIOS_DEBUG_Assert(0);
}
// Scale the accels
float accels[3] = {(float) accel_accum[0] / accel_samples,
(float) accel_accum[1] / accel_samples,
(float) accel_accum[2] / accel_samples};
float accels_out[3] = {accels[0] * accel_scaling * accel_scale[0] - accel_bias[0],
accels[1] * accel_scaling * accel_scale[1] - accel_bias[1],
accels[2] * accel_scaling * accel_scale[2] - accel_bias[2]};
if (rotate) {
rot_mult(R, accels_out, accels);
accelsData.x = accels[0];
accelsData.y = accels[1];
accelsData.z = accels[2];
} else {
accelsData.x = accels_out[0];
accelsData.y = accels_out[1];
accelsData.z = accels_out[2];
}
AccelsSet(&accelsData);
// Scale the gyros
float gyros[3] = {(float) gyro_accum[0] / gyro_samples,
(float) gyro_accum[1] / gyro_samples,
(float) gyro_accum[2] / gyro_samples};
float gyros_out[3] = {gyros[0] * gyro_scaling,
gyros[1] * gyro_scaling,
gyros[2] * gyro_scaling};
if (rotate) {
rot_mult(R, gyros_out, gyros);
gyrosData.x = gyros[0];
gyrosData.y = gyros[1];
gyrosData.z = gyros[2];
} else {
gyrosData.x = gyros_out[0];
gyrosData.y = gyros_out[1];
gyrosData.z = gyros_out[2];
}
if (bias_correct_gyro) {
// Apply bias correction to the gyros from the state estimator
GyrosBiasData gyrosBias;
GyrosBiasGet(&gyrosBias);
gyrosData.x -= gyrosBias.x;
gyrosData.y -= gyrosBias.y;
gyrosData.z -= gyrosBias.z;
}
GyrosSet(&gyrosData);
// Because most crafts wont get enough information from gravity to zero yaw gyro, we try
// and make it average zero (weakly)
#if defined(PIOS_INCLUDE_HMC5883)
MagnetometerData mag;
if (PIOS_HMC5883_NewDataAvailable() || PIOS_DELAY_DiffuS(mag_update_time) > 150000) {
int16_t values[3];
PIOS_HMC5883_ReadMag(values);
float mags[3] = {-(float) values[1] * mag_scale[0] - mag_bias[0],
-(float) values[0] * mag_scale[1] - mag_bias[1],
-(float) values[2] * mag_scale[2] - mag_bias[2]};
if (rotate) {
float mag_out[3];
rot_mult(R, mags, mag_out);
mag.x = mag_out[0];
mag.y = mag_out[1];
mag.z = mag_out[2];
} else {
mag.x = mags[0];
mag.y = mags[1];
mag.z = mags[2];
}
// Correct for mag bias and update if the rate is non zero
if(cal.MagBiasNullingRate > 0)
magOffsetEstimation(&mag);
MagnetometerSet(&mag);
mag_update_time = PIOS_DELAY_GetRaw();
}
#endif
PIOS_WDG_UpdateFlag(PIOS_WDG_SENSORS);
lastSysTime = xTaskGetTickCount();
}
}
void PIOS_Board_Init(void) {
/* Delay system */
PIOS_DELAY_Init();
const struct pios_board_info * bdinfo = &pios_board_info_blob;
#if defined(PIOS_INCLUDE_LED)
const struct pios_led_cfg * led_cfg = PIOS_BOARD_HW_DEFS_GetLedCfg(bdinfo->board_rev);
PIOS_Assert(led_cfg);
PIOS_LED_Init(led_cfg);
#endif /* PIOS_INCLUDE_LED */
#if defined(PIOS_INCLUDE_SPI)
/* Set up the SPI interface to the serial flash */
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
if (PIOS_SPI_Init(&pios_spi_flash_accel_id, &pios_spi_flash_accel_cfg_cc)) {
PIOS_Assert(0);
}
break;
case BOARD_REVISION_CC3D:
if (PIOS_SPI_Init(&pios_spi_flash_accel_id, &pios_spi_flash_accel_cfg_cc3d)) {
PIOS_Assert(0);
}
break;
default:
PIOS_Assert(0);
}
#endif
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
PIOS_Flash_Jedec_Init(&pios_external_flash_id, pios_spi_flash_accel_id, 1, &flash_w25x_cfg);
break;
case BOARD_REVISION_CC3D:
PIOS_Flash_Jedec_Init(&pios_external_flash_id, pios_spi_flash_accel_id, 0, &flash_m25p_cfg);
break;
default:
PIOS_DEBUG_Assert(0);
}
PIOS_Flash_Internal_Init(&pios_internal_flash_id, &flash_internal_cfg);
/* Register the partition table */
const struct pios_flash_partition * flash_partition_table;
uint32_t num_partitions;
flash_partition_table = PIOS_BOARD_HW_DEFS_GetPartitionTable(bdinfo->board_rev, &num_partitions);
PIOS_FLASH_register_partition_table(flash_partition_table, num_partitions);
/* Mount all filesystems */
PIOS_FLASHFS_Logfs_Init(&pios_uavo_settings_fs_id, &flashfs_settings_cfg, FLASH_PARTITION_LABEL_SETTINGS);
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Initialize UAVObject libraries */
EventDispatcherInitialize();
UAVObjInitialize();
/* Initialize the alarms library */
AlarmsInitialize();
HwCopterControlInitialize();
ModuleSettingsInitialize();
#if defined(PIOS_INCLUDE_RTC)
/* Initialize the real-time clock and its associated tick */
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
#ifndef ERASE_FLASH
/* Initialize watchdog as early as possible to catch faults during init */
PIOS_WDG_Init();
#endif
/* Check for repeated boot failures */
PIOS_IAP_Init();
uint16_t boot_count = PIOS_IAP_ReadBootCount();
if (boot_count < 3) {
PIOS_IAP_WriteBootCount(++boot_count);
AlarmsClear(SYSTEMALARMS_ALARM_BOOTFAULT);
} else {
/* Too many failed boot attempts, force hw configuration to defaults */
HwCopterControlSetDefaults(HwCopterControlHandle(), 0);
ModuleSettingsSetDefaults(ModuleSettingsHandle(),0);
AlarmsSet(SYSTEMALARMS_ALARM_BOOTFAULT, SYSTEMALARMS_ALARM_CRITICAL);
}
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Set up pulse timers */
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_2_cfg);
PIOS_TIM_InitClock(&tim_3_cfg);
PIOS_TIM_InitClock(&tim_4_cfg);
#if defined(PIOS_INCLUDE_USB)
/* Initialize board specific USB data */
PIOS_USB_BOARD_DATA_Init();
/* Flags to determine if various USB interfaces are advertised */
bool usb_hid_present = false;
bool usb_cdc_present = false;
#if defined(PIOS_INCLUDE_USB_CDC)
if (PIOS_USB_DESC_HID_CDC_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
usb_cdc_present = true;
#else
if (PIOS_USB_DESC_HID_ONLY_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
#endif
uintptr_t pios_usb_id;
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
PIOS_USB_Init(&pios_usb_id, &pios_usb_main_cfg_cc);
break;
case BOARD_REVISION_CC3D:
PIOS_USB_Init(&pios_usb_id, &pios_usb_main_cfg_cc3d);
break;
default:
PIOS_Assert(0);
}
#if defined(PIOS_INCLUDE_USB_CDC)
uint8_t hw_usb_vcpport;
/* Configure the USB VCP port */
HwCopterControlUSB_VCPPortGet(&hw_usb_vcpport);
if (!usb_cdc_present) {
/* Force VCP port function to disabled if we haven't advertised VCP in our USB descriptor */
hw_usb_vcpport = HWCOPTERCONTROL_USB_VCPPORT_DISABLED;
}
switch (hw_usb_vcpport) {
case HWCOPTERCONTROL_USB_VCPPORT_DISABLED:
break;
case HWCOPTERCONTROL_USB_VCPPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uintptr_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOPTERCONTROL_USB_VCPPORT_COMBRIDGE:
#if defined(PIOS_INCLUDE_COM)
{
uintptr_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_vcp_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOPTERCONTROL_USB_VCPPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uintptr_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_debug_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
NULL, 0,
tx_buffer, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_CDC */
#if defined(PIOS_INCLUDE_USB_HID)
/* Configure the usb HID port */
uint8_t hw_usb_hidport;
HwCopterControlUSB_HIDPortGet(&hw_usb_hidport);
if (!usb_hid_present) {
/* Force HID port function to disabled if we haven't advertised HID in our USB descriptor */
hw_usb_hidport = HWCOPTERCONTROL_USB_HIDPORT_DISABLED;
}
switch (hw_usb_hidport) {
case HWCOPTERCONTROL_USB_HIDPORT_DISABLED:
break;
case HWCOPTERCONTROL_USB_HIDPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uintptr_t pios_usb_hid_id;
if (PIOS_USB_HID_Init(&pios_usb_hid_id, &pios_usb_hid_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_hid_com_driver, pios_usb_hid_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOPTERCONTROL_USB_HIDPORT_RCTRANSMITTER:
#if defined(PIOS_INCLUDE_USB_RCTX)
{
if (PIOS_USB_RCTX_Init(&pios_usb_rctx_id, &pios_usb_rctx_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_USB_RCTX */
break;
}
#endif /* PIOS_INCLUDE_USB_HID */
#endif /* PIOS_INCLUDE_USB */
/* Configure the main IO port */
HwCopterControlDSMxModeOptions hw_DSMxMode;
HwCopterControlDSMxModeGet(&hw_DSMxMode);
uint8_t hw_mainport;
HwCopterControlMainPortGet(&hw_mainport);
switch (hw_mainport) {
case HWCOPTERCONTROL_MAINPORT_DISABLED:
break;
case HWCOPTERCONTROL_MAINPORT_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_RF_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOPTERCONTROL_MAINPORT_SBUS:
#if defined(PIOS_INCLUDE_SBUS)
{
uintptr_t pios_usart_sbus_id;
if (PIOS_USART_Init(&pios_usart_sbus_id, &pios_usart_sbus_main_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_id;
if (PIOS_SBus_Init(&pios_sbus_id, &pios_sbus_cfg, &pios_usart_com_driver, pios_usart_sbus_id)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_rcvr_id;
if (PIOS_RCVR_Init(&pios_sbus_rcvr_id, &pios_sbus_rcvr_driver, pios_sbus_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_SBUS] = pios_sbus_rcvr_id;
}
#endif /* PIOS_INCLUDE_SBUS */
break;
case HWCOPTERCONTROL_MAINPORT_GPS:
#if defined(PIOS_INCLUDE_GPS)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_GPS_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
NULL, 0)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_GPS */
break;
case HWCOPTERCONTROL_MAINPORT_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
uintptr_t pios_usart_dsm_id;
if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_hsum_main_cfg)) {
PIOS_Assert(0);
}
if (hw_DSMxMode >= HWCOPTERCONTROL_DSMXMODE_BIND3PULSES) {
hw_DSMxMode = HWCOPTERCONTROL_DSMXMODE_AUTODETECT; /* Do not try to bind through XOR */
}
uintptr_t pios_dsm_id;
if (PIOS_DSM_Init(&pios_dsm_id,
&pios_dsm_main_cfg,
&pios_usart_com_driver,
pios_usart_dsm_id, hw_DSMxMode)) {
PIOS_Assert(0);
}
uintptr_t pios_dsm_rcvr_id;
if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM] = pios_dsm_rcvr_id;
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOPTERCONTROL_MAINPORT_HOTTSUMD:
case HWCOPTERCONTROL_MAINPORT_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
proto = (hw_mainport == HWCOPTERCONTROL_MAINPORT_HOTTSUMD) ? PIOS_HSUM_PROTO_SUMD : PIOS_HSUM_PROTO_SUMH;
uintptr_t pios_usart_hsum_id;
if (PIOS_USART_Init(&pios_usart_hsum_id, &pios_usart_dsm_hsum_main_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_hsum_id;
if (PIOS_HSUM_Init(&pios_hsum_id, &pios_usart_com_driver, pios_usart_hsum_id, proto)) {
PIOS_Assert(0);
}
uintptr_t pios_hsum_rcvr_id;
if (PIOS_RCVR_Init(&pios_hsum_rcvr_id, &pios_hsum_rcvr_driver, pios_hsum_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM] = pios_hsum_rcvr_id;
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOPTERCONTROL_MAINPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_debug_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOPTERCONTROL_MAINPORT_COMBRIDGE:
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_bridge_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
break;
case HWCOPTERCONTROL_MAINPORT_MAVLINKTX:
#if defined(PIOS_INCLUDE_MAVLINK)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_MAVLINK_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_mavlink_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_MAVLINK_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOPTERCONTROL_MAINPORT_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_GPS)
#if defined(PIOS_INCLUDE_MAVLINK)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_GPS_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_MAVLINK_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
tx_buffer, PIOS_COM_MAVLINK_TX_BUF_LEN)) {
PIOS_Assert(0);
}
pios_com_mavlink_id = pios_com_gps_id;
}
#endif /* PIOS_INCLUDE_MAVLINK */
#endif /* PIOS_INCLUDE_GPS */
break;
case HWCOPTERCONTROL_MAINPORT_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_frsky_sensor_hub_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_FRSKYSENSORHUB */
break;
case HWCOPTERCONTROL_MAINPORT_LIGHTTELEMETRYTX:
{
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_lighttelemetry_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN)) {
PIOS_Assert(0);
}
#endif
}
break;
}
/* Configure the flexi port */
uint8_t hw_flexiport;
HwCopterControlFlexiPortGet(&hw_flexiport);
switch (hw_flexiport) {
case HWCOPTERCONTROL_FLEXIPORT_DISABLED:
break;
case HWCOPTERCONTROL_FLEXIPORT_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_RF_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOPTERCONTROL_FLEXIPORT_COMBRIDGE:
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_bridge_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
break;
case HWCOPTERCONTROL_FLEXIPORT_GPS:
#if defined(PIOS_INCLUDE_GPS)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_GPS_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
NULL, 0)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_GPS */
break;
case HWCOPTERCONTROL_FLEXIPORT_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
uintptr_t pios_usart_dsm_id;
if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_hsum_flexi_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_dsm_id;
if (PIOS_DSM_Init(&pios_dsm_id,
&pios_dsm_flexi_cfg,
&pios_usart_com_driver,
pios_usart_dsm_id, hw_DSMxMode)) {
PIOS_Assert(0);
}
uintptr_t pios_dsm_rcvr_id;
if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM] = pios_dsm_rcvr_id;
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOPTERCONTROL_FLEXIPORT_HOTTSUMD:
case HWCOPTERCONTROL_FLEXIPORT_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
proto = (hw_flexiport == HWCOPTERCONTROL_FLEXIPORT_HOTTSUMD) ? PIOS_HSUM_PROTO_SUMD : PIOS_HSUM_PROTO_SUMH;
uintptr_t pios_usart_hsum_id;
if (PIOS_USART_Init(&pios_usart_hsum_id, &pios_usart_dsm_hsum_flexi_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_hsum_id;
if (PIOS_HSUM_Init(&pios_hsum_id, &pios_usart_com_driver, pios_usart_hsum_id, proto)) {
PIOS_Assert(0);
}
uintptr_t pios_hsum_rcvr_id;
if (PIOS_RCVR_Init(&pios_hsum_rcvr_id, &pios_hsum_rcvr_driver, pios_hsum_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM] = pios_hsum_rcvr_id;
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOPTERCONTROL_FLEXIPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_debug_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOPTERCONTROL_FLEXIPORT_I2C:
#if defined(PIOS_INCLUDE_I2C)
{
if (PIOS_I2C_Init(&pios_i2c_flexi_adapter_id, &pios_i2c_flexi_adapter_cfg)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_I2C */
#if defined(PIOS_INCLUDE_PCF8591)
{
uintptr_t pcf8591_adc_id;
if(PIOS_PCF8591_ADC_Init(&pcf8591_adc_id, &pios_8591_cfg) < 0)
PIOS_Assert(0);
PIOS_ADC_Init(&pios_pcf8591_adc_id, &pios_pcf8591_adc_driver, pcf8591_adc_id);
}
#endif
break;
case HWCOPTERCONTROL_FLEXIPORT_MAVLINKTX:
#if defined(PIOS_INCLUDE_MAVLINK)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_MAVLINK_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_mavlink_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_MAVLINK_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOPTERCONTROL_FLEXIPORT_LIGHTTELEMETRYTX:
{
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_lighttelemetry_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN)) {
PIOS_Assert(0);
}
#endif
case HWCOPTERCONTROL_FLEXIPORT_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB)
{
uintptr_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_frsky_sensor_hub_id, &pios_usart_com_driver, pios_usart_generic_id,
NULL, 0,
tx_buffer, PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_FRSKYSENSORHUB */
break;
}
break;
}
/* Configure the rcvr port */
uint8_t hw_rcvrport;
HwCopterControlRcvrPortGet(&hw_rcvrport);
switch (hw_rcvrport) {
case HWCOPTERCONTROL_RCVRPORT_DISABLED:
break;
case HWCOPTERCONTROL_RCVRPORT_PWM:
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
case HWCOPTERCONTROL_RCVRPORT_PPM:
case HWCOPTERCONTROL_RCVRPORT_PPMONPIN8:
case HWCOPTERCONTROL_RCVRPORT_PPMOUTPUTS:
#if defined(PIOS_INCLUDE_PPM)
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id,
(hw_rcvrport == HWCOPTERCONTROL_RCVRPORT_PPMONPIN8) ? &pios_ppm_pin8_cfg : &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
break;
case HWCOPTERCONTROL_RCVRPORT_PPMPWM:
/* This is a combination of PPM and PWM inputs */
#if defined(PIOS_INCLUDE_PPM)
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_with_ppm_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
}
#if defined(PIOS_INCLUDE_GCSRCVR)
GCSReceiverInitialize();
uintptr_t pios_gcsrcvr_id;
PIOS_GCSRCVR_Init(&pios_gcsrcvr_id);
uintptr_t pios_gcsrcvr_rcvr_id;
if (PIOS_RCVR_Init(&pios_gcsrcvr_rcvr_id, &pios_gcsrcvr_rcvr_driver, pios_gcsrcvr_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_GCS] = pios_gcsrcvr_rcvr_id;
#endif /* PIOS_INCLUDE_GCSRCVR */
/* Remap AFIO pin for PB4 (Servo 5 Out)*/
GPIO_PinRemapConfig( GPIO_Remap_SWJ_NoJTRST, ENABLE);
#ifndef PIOS_DEBUG_ENABLE_DEBUG_PINS
switch (hw_rcvrport) {
case HWCOPTERCONTROL_RCVRPORT_DISABLED:
case HWCOPTERCONTROL_RCVRPORT_PWM:
case HWCOPTERCONTROL_RCVRPORT_PPM:
case HWCOPTERCONTROL_RCVRPORT_PPMONPIN8:
case HWCOPTERCONTROL_RCVRPORT_PPMPWM:
PIOS_Servo_Init(&pios_servo_cfg);
break;
case HWCOPTERCONTROL_RCVRPORT_PPMOUTPUTS:
case HWCOPTERCONTROL_RCVRPORT_OUTPUTS:
PIOS_Servo_Init(&pios_servo_rcvr_cfg);
break;
}
#else
PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels));
#endif /* PIOS_DEBUG_ENABLE_DEBUG_PINS */
PIOS_SENSORS_Init();
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
// Revision 1 with invensense gyros, start the ADC
#if defined(PIOS_INCLUDE_ADC)
{
uint32_t internal_adc_id;
PIOS_INTERNAL_ADC_Init(&internal_adc_id, &internal_adc_cfg);
PIOS_ADC_Init(&pios_internal_adc_id, &pios_internal_adc_driver, internal_adc_id);
}
#endif
#if defined(PIOS_INCLUDE_ADXL345)
PIOS_ADXL345_Init(pios_spi_flash_accel_id, 0);
#endif
break;
case BOARD_REVISION_CC3D:
// Revision 2 with L3GD20 gyros, start a SPI interface and connect to it
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
#if defined(PIOS_INCLUDE_MPU6000)
// Set up the SPI interface to the serial flash
if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) {
PIOS_Assert(0);
}
PIOS_MPU6000_Init(pios_spi_gyro_id,0,&pios_mpu6000_cfg);
init_test = PIOS_MPU6000_Test();
uint8_t hw_gyro_range;
HwCopterControlGyroRangeGet(&hw_gyro_range);
switch(hw_gyro_range) {
case HWCOPTERCONTROL_GYRORANGE_250:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_250_DEG);
break;
case HWCOPTERCONTROL_GYRORANGE_500:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_500_DEG);
break;
case HWCOPTERCONTROL_GYRORANGE_1000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_1000_DEG);
break;
case HWCOPTERCONTROL_GYRORANGE_2000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_2000_DEG);
break;
}
uint8_t hw_accel_range;
HwCopterControlAccelRangeGet(&hw_accel_range);
switch(hw_accel_range) {
case HWCOPTERCONTROL_ACCELRANGE_2G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_2G);
break;
case HWCOPTERCONTROL_ACCELRANGE_4G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_4G);
break;
case HWCOPTERCONTROL_ACCELRANGE_8G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_8G);
break;
case HWCOPTERCONTROL_ACCELRANGE_16G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_16G);
break;
}
// the filter has to be set before rate else divisor calculation will fail
uint8_t hw_mpu6000_dlpf;
HwCopterControlMPU6000DLPFGet(&hw_mpu6000_dlpf);
enum pios_mpu60x0_filter mpu6000_dlpf = \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_256) ? PIOS_MPU60X0_LOWPASS_256_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_188) ? PIOS_MPU60X0_LOWPASS_188_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_98) ? PIOS_MPU60X0_LOWPASS_98_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_42) ? PIOS_MPU60X0_LOWPASS_42_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_20) ? PIOS_MPU60X0_LOWPASS_20_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_10) ? PIOS_MPU60X0_LOWPASS_10_HZ : \
(hw_mpu6000_dlpf == HWCOPTERCONTROL_MPU6000DLPF_5) ? PIOS_MPU60X0_LOWPASS_5_HZ : \
pios_mpu6000_cfg.default_filter;
PIOS_MPU6000_SetLPF(mpu6000_dlpf);
uint8_t hw_mpu6000_samplerate;
HwCopterControlMPU6000RateGet(&hw_mpu6000_samplerate);
uint16_t mpu6000_samplerate = \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_200) ? 200 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_333) ? 333 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_500) ? 500 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_666) ? 666 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_1000) ? 1000 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_2000) ? 2000 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_4000) ? 4000 : \
(hw_mpu6000_samplerate == HWCOPTERCONTROL_MPU6000RATE_8000) ? 8000 : \
pios_mpu6000_cfg.default_samplerate;
PIOS_MPU6000_SetSampleRate(mpu6000_samplerate);
#endif /* PIOS_INCLUDE_MPU6000 */
break;
default:
PIOS_Assert(0);
}
PIOS_GPIO_Init();
/* Make sure we have at least one telemetry link configured or else fail initialization */
PIOS_Assert(pios_com_telem_rf_id || pios_com_telem_usb_id);
}
void PIOS_Board_Init(void)
{
/* Delay system */
PIOS_DELAY_Init();
const struct pios_board_info *bdinfo = &pios_board_info_blob;
#if defined(PIOS_INCLUDE_LED)
const struct pios_led_cfg *led_cfg =
PIOS_BOARD_HW_DEFS_GetLedCfg(bdinfo->board_rev);
PIOS_Assert(led_cfg);
PIOS_LED_Init(led_cfg);
#endif /* PIOS_INCLUDE_LED */
#if defined(PIOS_INCLUDE_I2C)
if (PIOS_I2C_Init
(&pios_i2c_internal_adapter_id,
&pios_i2c_internal_adapter_cfg)) {
PIOS_DEBUG_Assert(0);
}
if (PIOS_I2C_CheckClear(pios_i2c_internal_adapter_id) != 0)
panic(5);
#endif
#if defined(PIOS_INCLUDE_SPI)
if (PIOS_SPI_Init(&pios_spi_flash_id, &pios_spi_flash_cfg)) {
PIOS_DEBUG_Assert(0);
}
if (PIOS_SPI_Init
(&pios_spi_gyro_accel_id, &pios_spi_gyro_accel_cfg)) {
PIOS_Assert(0);
}
#endif
#if defined(PIOS_INCLUDE_FLASH)
/* Inititialize all flash drivers */
if (PIOS_Flash_Jedec_Init
(&pios_external_flash_id, pios_spi_flash_id, 0,
&flash_mx25_cfg) != 0)
panic(1);
if (PIOS_Flash_Internal_Init
(&pios_internal_flash_id, &flash_internal_cfg) != 0)
panic(1);
/* Register the partition table */
const struct pios_flash_partition *flash_partition_table;
uint32_t num_partitions;
flash_partition_table =
PIOS_BOARD_HW_DEFS_GetPartitionTable(bdinfo->board_rev,
&num_partitions);
PIOS_FLASH_register_partition_table(flash_partition_table,
num_partitions);
/* Mount all filesystems */
if (PIOS_FLASHFS_Logfs_Init
(&pios_uavo_settings_fs_id, &flashfs_settings_cfg,
FLASH_PARTITION_LABEL_SETTINGS) != 0)
panic(1);
if (PIOS_FLASHFS_Logfs_Init
(&pios_waypoints_settings_fs_id, &flashfs_waypoints_cfg,
FLASH_PARTITION_LABEL_WAYPOINTS) != 0)
panic(1);
#if defined(ERASE_FLASH)
PIOS_FLASHFS_Format(pios_uavo_settings_fs_id);
#endif
#endif /* PIOS_INCLUDE_FLASH */
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Initialize UAVObject libraries */
UAVObjInitialize();
/* Initialize the alarms library. Reads RCC reset flags */
AlarmsInitialize();
PIOS_RESET_Clear(); // Clear the RCC reset flags after use.
/* Initialize the hardware UAVOs */
HwColibriInitialize();
ModuleSettingsInitialize();
#if defined(PIOS_INCLUDE_RTC)
/* Initialize the real-time clock and its associated tick */
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
#ifndef ERASE_FLASH
/* Initialize watchdog as early as possible to catch faults during init
* but do it only if there is no debugger connected
*/
if ((CoreDebug->DHCSR & CoreDebug_DHCSR_C_DEBUGEN_Msk) == 0) {
PIOS_WDG_Init();
}
#endif
/* Set up pulse timers */
//Timers used for inputs (1, 2, 5, 8)
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_2_cfg);
PIOS_TIM_InitClock(&tim_5_cfg);
PIOS_TIM_InitClock(&tim_8_cfg);
// Timers used for outputs (3, 10, 11, 12)
PIOS_TIM_InitClock(&tim_3_cfg);
PIOS_TIM_InitClock(&tim_10_cfg);
PIOS_TIM_InitClock(&tim_11_cfg);
PIOS_TIM_InitClock(&tim_12_cfg);
/* IAP System Setup */
PIOS_IAP_Init();
uint16_t boot_count = PIOS_IAP_ReadBootCount();
if (boot_count < 3) {
PIOS_IAP_WriteBootCount(++boot_count);
AlarmsClear(SYSTEMALARMS_ALARM_BOOTFAULT);
} else {
/* Too many failed boot attempts, force hw config to defaults */
HwColibriSetDefaults(HwColibriHandle(), 0);
ModuleSettingsSetDefaults(ModuleSettingsHandle(), 0);
AlarmsSet(SYSTEMALARMS_ALARM_BOOTFAULT,
SYSTEMALARMS_ALARM_CRITICAL);
}
#if defined(PIOS_INCLUDE_USB)
/* Initialize board specific USB data */
PIOS_USB_BOARD_DATA_Init();
/* Flags to determine if various USB interfaces are advertised */
bool usb_hid_present = false;
bool usb_cdc_present = false;
#if defined(PIOS_INCLUDE_USB_CDC)
if (PIOS_USB_DESC_HID_CDC_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
usb_cdc_present = true;
#else
if (PIOS_USB_DESC_HID_ONLY_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
#endif
uintptr_t pios_usb_id;
PIOS_USB_Init(&pios_usb_id,
PIOS_BOARD_HW_DEFS_GetUsbCfg(bdinfo->board_rev));
#if defined(PIOS_INCLUDE_USB_CDC)
uint8_t hw_usb_vcpport;
/* Configure the USB VCP port */
HwColibriUSB_VCPPortGet(&hw_usb_vcpport);
if (!usb_cdc_present) {
/* Force VCP port function to disabled if we haven't advertised VCP in our USB descriptor */
hw_usb_vcpport = HWCOLIBRI_USB_VCPPORT_DISABLED;
}
uintptr_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init
(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
switch (hw_usb_vcpport) {
case HWCOLIBRI_USB_VCPPORT_DISABLED:
break;
case HWCOLIBRI_USB_VCPPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t *rx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t *tx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init
(&pios_com_telem_usb_id,
&pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOLIBRI_USB_VCPPORT_COMBRIDGE:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t *rx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t *tx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init
(&pios_com_vcp_id, &pios_usb_cdc_com_driver,
pios_usb_cdc_id, rx_buffer,
PIOS_COM_BRIDGE_RX_BUF_LEN, tx_buffer,
PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOLIBRI_USB_VCPPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uint8_t *tx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init
(&pios_com_debug_id, &pios_usb_cdc_com_driver,
pios_usb_cdc_id, NULL, 0, tx_buffer,
PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
case HWCOLIBRI_USB_VCPPORT_PICOC:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t *rx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_PICOC_RX_BUF_LEN);
uint8_t *tx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_PICOC_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init
(&pios_com_picoc_id, &pios_usb_cdc_com_driver,
pios_usb_cdc_id, rx_buffer,
PIOS_COM_PICOC_RX_BUF_LEN, tx_buffer,
PIOS_COM_PICOC_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_CDC */
#if defined(PIOS_INCLUDE_USB_HID)
/* Configure the usb HID port */
uint8_t hw_usb_hidport;
HwColibriUSB_HIDPortGet(&hw_usb_hidport);
if (!usb_hid_present) {
/* Force HID port function to disabled if we haven't advertised HID in our USB descriptor */
hw_usb_hidport = HWCOLIBRI_USB_HIDPORT_DISABLED;
}
uintptr_t pios_usb_hid_id;
if (PIOS_USB_HID_Init
(&pios_usb_hid_id, &pios_usb_hid_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
switch (hw_usb_hidport) {
case HWCOLIBRI_USB_HIDPORT_DISABLED:
break;
case HWCOLIBRI_USB_HIDPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t *rx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t *tx_buffer =
(uint8_t *)
PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init
(&pios_com_telem_usb_id,
&pios_usb_hid_com_driver, pios_usb_hid_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_HID */
if (usb_hid_present || usb_cdc_present) {
PIOS_USBHOOK_Activate();
}
#endif /* PIOS_INCLUDE_USB */
/* Configure the IO ports */
HwColibriDSMxModeOptions hw_DSMxMode;
HwColibriDSMxModeGet(&hw_DSMxMode);
/* init sensor queue registration */
PIOS_SENSORS_Init();
/* UART1 Port */
uint8_t hw_uart1;
HwColibriUart1Get(&hw_uart1);
switch (hw_uart1) {
case HWCOLIBRI_UART1_DISABLED:
break;
case HWCOLIBRI_UART1_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_TELEM_RF_RX_BUF_LEN,
PIOS_COM_TELEM_RF_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_telem_rf_id);
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOLIBRI_UART1_GPS:
#if defined(PIOS_INCLUDE_GPS) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_GPS_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
#endif
break;
case HWCOLIBRI_UART1_I2C:
#if defined(PIOS_INCLUDE_I2C)
if (PIOS_I2C_Init
(&pios_i2c_usart1_adapter_id,
&pios_i2c_usart1_adapter_cfg)) {
PIOS_Assert(0);
}
if (PIOS_I2C_CheckClear(pios_i2c_usart1_adapter_id) != 0)
panic(6);
#if defined(PIOS_INCLUDE_HMC5883)
{
uint8_t Magnetometer;
HwColibriMagnetometerGet(&Magnetometer);
if (Magnetometer ==
HWCOLIBRI_MAGNETOMETER_EXTERNALI2CUART1) {
// init sensor
if (PIOS_HMC5883_Init
(pios_i2c_usart1_adapter_id,
&pios_hmc5883_external_cfg) != 0)
panic(8);
if (PIOS_HMC5883_Test() != 0)
panic(8);
}
}
#endif /* PIOS_INCLUDE_HMC5883 */
#endif /* PIOS_INCLUDE_I2C */
break;
case HWCOLIBRI_UART1_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
PIOS_Board_configure_dsm(&pios_usart1_dsm_hsum_cfg,
&pios_usart1_dsm_aux_cfg,
&pios_usart_com_driver,
MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM,
&hw_DSMxMode);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOLIBRI_UART1_HOTTSUMD:
case HWCOLIBRI_UART1_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_uart1) {
case HWCOLIBRI_UART1_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWCOLIBRI_UART1_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum
(&pios_usart1_dsm_hsum_cfg,
&pios_usart_com_driver, &proto,
MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOLIBRI_UART1_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg, 0,
PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_debug_id);
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWCOLIBRI_UART1_COMBRIDGE:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_BRIDGE_RX_BUF_LEN,
PIOS_COM_BRIDGE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_bridge_id);
#endif
break;
case HWCOLIBRI_UART1_MAVLINKTX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart1_cfg, 0,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART1_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK) && defined(PIOS_INCLUDE_GPS)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART1_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_HOTT_RX_BUF_LEN,
PIOS_COM_HOTT_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWCOLIBRI_UART1_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg, 0,
PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWCOLIBRI_UART1_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart1_cfg, 0,
PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_lighttelemetry_id);
#endif
break;
case HWCOLIBRI_UART1_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart1_cfg,
PIOS_COM_PICOC_RX_BUF_LEN,
PIOS_COM_PICOC_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
}
/* UART2 Port */
uint8_t hw_uart2;
HwColibriUart2Get(&hw_uart2);
switch (hw_uart2) {
case HWCOLIBRI_UART2_DISABLED:
break;
case HWCOLIBRI_UART2_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_TELEM_RF_RX_BUF_LEN,
PIOS_COM_TELEM_RF_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_telem_rf_id);
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOLIBRI_UART2_GPS:
#if defined(PIOS_INCLUDE_GPS) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_GPS_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
#endif
break;
case HWCOLIBRI_UART2_SBUS:
//hardware signal inverter required
#if defined(PIOS_INCLUDE_SBUS) && defined(PIOS_INCLUDE_USART)
{
uintptr_t pios_usart_sbus_id;
if (PIOS_USART_Init
(&pios_usart_sbus_id, &pios_usart2_sbus_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_id;
if (PIOS_SBus_Init
(&pios_sbus_id, &pios_usart2_sbus_aux_cfg,
&pios_usart_com_driver, pios_usart_sbus_id)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_rcvr_id;
if (PIOS_RCVR_Init
(&pios_sbus_rcvr_id, &pios_sbus_rcvr_driver,
pios_sbus_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_SBUS] =
pios_sbus_rcvr_id;
}
#endif /* PIOS_INCLUDE_SBUS */
break;
case HWCOLIBRI_UART2_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
PIOS_Board_configure_dsm(&pios_usart2_dsm_hsum_cfg,
&pios_usart2_dsm_aux_cfg,
&pios_usart_com_driver,
MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM,
&hw_DSMxMode);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOLIBRI_UART2_HOTTSUMD:
case HWCOLIBRI_UART2_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_uart2) {
case HWCOLIBRI_UART2_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWCOLIBRI_UART2_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum
(&pios_usart2_dsm_hsum_cfg,
&pios_usart_com_driver, &proto,
MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOLIBRI_UART2_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg, 0,
PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_debug_id);
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWCOLIBRI_UART2_COMBRIDGE:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_BRIDGE_RX_BUF_LEN,
PIOS_COM_BRIDGE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_bridge_id);
#endif
break;
case HWCOLIBRI_UART2_MAVLINKTX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart2_cfg, 0,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART2_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK) && defined(PIOS_INCLUDE_GPS)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART2_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_HOTT_RX_BUF_LEN,
PIOS_COM_HOTT_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWCOLIBRI_UART2_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg, 0,
PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWCOLIBRI_UART2_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart2_cfg, 0,
PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_lighttelemetry_id);
#endif
break;
case HWCOLIBRI_UART2_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart2_cfg,
PIOS_COM_PICOC_RX_BUF_LEN,
PIOS_COM_PICOC_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
}
if (hw_uart2 != HWCOLIBRI_UART2_SBUS) {
GPIO_Init(pios_usart2_sbus_aux_cfg.inv.gpio, (GPIO_InitTypeDef*)&pios_usart2_sbus_aux_cfg.inv.init);
GPIO_WriteBit(pios_usart2_sbus_aux_cfg.inv.gpio, pios_usart2_sbus_aux_cfg.inv.init.GPIO_Pin, pios_usart2_sbus_aux_cfg.gpio_inv_disable);
}
/* UART3 Port */
uint8_t hw_uart3;
HwColibriUart3Get(&hw_uart3);
switch (hw_uart3) {
case HWCOLIBRI_UART3_DISABLED:
break;
case HWCOLIBRI_UART3_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_TELEM_RF_RX_BUF_LEN,
PIOS_COM_TELEM_RF_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_telem_rf_id);
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOLIBRI_UART3_GPS:
#if defined(PIOS_INCLUDE_GPS) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_GPS_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
#endif
break;
case HWCOLIBRI_UART3_I2C:
#if defined(PIOS_INCLUDE_I2C)
if (PIOS_I2C_Init
(&pios_i2c_usart3_adapter_id,
&pios_i2c_usart3_adapter_cfg)) {
PIOS_Assert(0);
}
if (PIOS_I2C_CheckClear(pios_i2c_usart3_adapter_id) != 0)
panic(7);
#if defined(PIOS_INCLUDE_HMC5883)
{
uint8_t Magnetometer;
HwColibriMagnetometerGet(&Magnetometer);
if (Magnetometer ==
HWCOLIBRI_MAGNETOMETER_EXTERNALI2CUART3) {
// init sensor
if (PIOS_HMC5883_Init
(pios_i2c_usart3_adapter_id,
&pios_hmc5883_external_cfg) != 0)
panic(9);
if (PIOS_HMC5883_Test() != 0)
panic(9);
}
}
#endif /* PIOS_INCLUDE_HMC5883 */
#endif /* PIOS_INCLUDE_I2C */
break;
case HWCOLIBRI_UART3_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
PIOS_Board_configure_dsm(&pios_usart3_dsm_hsum_cfg,
&pios_usart3_dsm_aux_cfg,
&pios_usart_com_driver,
MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM,
&hw_DSMxMode);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOLIBRI_UART3_HOTTSUMD:
case HWCOLIBRI_UART3_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_uart3) {
case HWCOLIBRI_UART3_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWCOLIBRI_UART3_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum
(&pios_usart3_dsm_hsum_cfg,
&pios_usart_com_driver, &proto,
MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOLIBRI_UART3_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg, 0,
PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_debug_id);
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWCOLIBRI_UART3_COMBRIDGE:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_BRIDGE_RX_BUF_LEN,
PIOS_COM_BRIDGE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_bridge_id);
#endif
break;
case HWCOLIBRI_UART3_MAVLINKTX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart3_cfg, 0,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART3_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK) && defined(PIOS_INCLUDE_GPS)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART3_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_HOTT_RX_BUF_LEN,
PIOS_COM_HOTT_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWCOLIBRI_UART3_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg, 0,
PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWCOLIBRI_UART3_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart3_cfg,
PIOS_COM_PICOC_RX_BUF_LEN,
PIOS_COM_PICOC_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
case HWCOLIBRI_UART3_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart3_cfg, 0,
PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_lighttelemetry_id);
#endif
break;
}
/* UART4 Port */
uint8_t hw_uart4;
HwColibriUart4Get(&hw_uart4);
switch (hw_uart4) {
case HWCOLIBRI_UART4_DISABLED:
break;
case HWCOLIBRI_UART4_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_TELEM_RF_RX_BUF_LEN,
PIOS_COM_TELEM_RF_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_telem_rf_id);
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWCOLIBRI_UART4_GPS:
#if defined(PIOS_INCLUDE_GPS) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_GPS_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
#endif
break;
case HWCOLIBRI_UART4_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
PIOS_Board_configure_dsm(&pios_usart4_dsm_hsum_cfg,
&pios_usart4_dsm_aux_cfg,
&pios_usart_com_driver,
MANUALCONTROLSETTINGS_CHANNELGROUPS_DSM,
&hw_DSMxMode);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWCOLIBRI_UART4_HOTTSUMD:
case HWCOLIBRI_UART4_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_uart4) {
case HWCOLIBRI_UART4_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWCOLIBRI_UART4_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum
(&pios_usart4_dsm_hsum_cfg,
&pios_usart_com_driver, &proto,
MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWCOLIBRI_UART4_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg, 0,
PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_debug_id);
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWCOLIBRI_UART4_COMBRIDGE:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_BRIDGE_RX_BUF_LEN,
PIOS_COM_BRIDGE_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_bridge_id);
#endif
break;
case HWCOLIBRI_UART4_MAVLINKTX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart4_cfg, 0,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART4_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM) && defined(PIOS_INCLUDE_MAVLINK) && defined(PIOS_INCLUDE_GPS)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_GPS_RX_BUF_LEN,
PIOS_COM_MAVLINK_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWCOLIBRI_UART4_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_HOTT_RX_BUF_LEN,
PIOS_COM_HOTT_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWCOLIBRI_UART4_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg, 0,
PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWCOLIBRI_UART4_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart4_cfg, 0,
PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_lighttelemetry_id);
#endif
break;
case HWCOLIBRI_UART4_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart4_cfg,
PIOS_COM_PICOC_RX_BUF_LEN,
PIOS_COM_PICOC_TX_BUF_LEN,
&pios_usart_com_driver,
&pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
}
/* Configure the rcvr port */
uint8_t hw_rcvrport;
HwColibriRcvrPortGet(&hw_rcvrport);
switch (hw_rcvrport) {
case HWCOLIBRI_RCVRPORT_DISABLED:
break;
case HWCOLIBRI_RCVRPORT_PWM:
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver,
pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] =
pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
case HWCOLIBRI_RCVRPORT_PWMADC:
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id,
&pios_pwm_with_adc_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver,
pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] =
pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
case HWCOLIBRI_RCVRPORT_PPM:
case HWCOLIBRI_RCVRPORT_PPMADC:
case HWCOLIBRI_RCVRPORT_PPMOUTPUTS:
case HWCOLIBRI_RCVRPORT_PPMOUTPUTSADC:
#if defined(PIOS_INCLUDE_PPM)
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver,
pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] =
pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
break;
case HWCOLIBRI_RCVRPORT_PPMPWM:
/* This is a combination of PPM and PWM inputs */
#if defined(PIOS_INCLUDE_PPM)
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver,
pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] =
pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id,
&pios_pwm_with_ppm_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver,
pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] =
pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
case HWCOLIBRI_RCVRPORT_PPMPWMADC:
/* This is a combination of PPM and PWM inputs with IN6 and IN7 free for adc */
#if defined(PIOS_INCLUDE_PPM)
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver,
pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] =
pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
#if defined(PIOS_INCLUDE_PWM)
{
uintptr_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id,
&pios_pwm_with_ppm_with_adc_cfg);
uintptr_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init
(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver,
pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map
[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] =
pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
}
#if defined(PIOS_INCLUDE_GCSRCVR)
GCSReceiverInitialize();
uintptr_t pios_gcsrcvr_id;
PIOS_GCSRCVR_Init(&pios_gcsrcvr_id);
uintptr_t pios_gcsrcvr_rcvr_id;
if (PIOS_RCVR_Init
(&pios_gcsrcvr_rcvr_id, &pios_gcsrcvr_rcvr_driver,
pios_gcsrcvr_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_GCS] =
pios_gcsrcvr_rcvr_id;
#endif /* PIOS_INCLUDE_GCSRCVR */
#ifndef PIOS_DEBUG_ENABLE_DEBUG_PINS
switch (hw_rcvrport) {
case HWCOLIBRI_RCVRPORT_DISABLED:
case HWCOLIBRI_RCVRPORT_PWM:
case HWCOLIBRI_RCVRPORT_PWMADC:
case HWCOLIBRI_RCVRPORT_PPM:
case HWCOLIBRI_RCVRPORT_PPMADC:
case HWCOLIBRI_RCVRPORT_PPMPWM:
case HWCOLIBRI_RCVRPORT_PPMPWMADC:
/* Set up the servo outputs */
#ifdef PIOS_INCLUDE_SERVO
PIOS_Servo_Init(&pios_servo_cfg);
#endif
break;
case HWCOLIBRI_RCVRPORT_PPMOUTPUTS:
case HWCOLIBRI_RCVRPORT_OUTPUTS:
#ifdef PIOS_INCLUDE_SERVO
PIOS_Servo_Init(&pios_servo_with_rcvr_cfg);
#endif
break;
case HWCOLIBRI_RCVRPORT_PPMOUTPUTSADC:
case HWCOLIBRI_RCVRPORT_OUTPUTSADC:
#ifdef PIOS_INCLUDE_SERVO
PIOS_Servo_Init(&pios_servo_with_rcvr_with_adc_cfg);
#endif
break;
}
#else
PIOS_DEBUG_Init(&pios_tim_servo_all_channels,
NELEMENTS(pios_tim_servo_all_channels));
#endif
PIOS_WDG_Clear();
PIOS_DELAY_WaitmS(200);
PIOS_WDG_Clear();
#if defined(PIOS_INCLUDE_MPU6000)
if (PIOS_MPU6000_Init(pios_spi_gyro_accel_id, 0, &pios_mpu6000_cfg)
!= 0)
panic(2);
if (PIOS_MPU6000_Test() != 0)
panic(2);
// To be safe map from UAVO enum to driver enum
uint8_t hw_gyro_range;
HwColibriGyroRangeGet(&hw_gyro_range);
switch (hw_gyro_range) {
case HWCOLIBRI_GYRORANGE_250:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_250_DEG);
break;
case HWCOLIBRI_GYRORANGE_500:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_500_DEG);
break;
case HWCOLIBRI_GYRORANGE_1000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_1000_DEG);
break;
case HWCOLIBRI_GYRORANGE_2000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_2000_DEG);
break;
}
uint8_t hw_accel_range;
HwColibriAccelRangeGet(&hw_accel_range);
switch (hw_accel_range) {
case HWCOLIBRI_ACCELRANGE_2G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_2G);
break;
case HWCOLIBRI_ACCELRANGE_4G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_4G);
break;
case HWCOLIBRI_ACCELRANGE_8G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_8G);
break;
case HWCOLIBRI_ACCELRANGE_16G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_16G);
break;
}
// the filter has to be set before rate else divisor calculation will fail
uint8_t hw_mpu6000_dlpf;
HwColibriMPU6000DLPFGet(&hw_mpu6000_dlpf);
enum pios_mpu60x0_filter mpu6000_dlpf =
(hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_256) ? PIOS_MPU60X0_LOWPASS_256_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_188) ? PIOS_MPU60X0_LOWPASS_188_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_98) ? PIOS_MPU60X0_LOWPASS_98_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_42) ? PIOS_MPU60X0_LOWPASS_42_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_20) ? PIOS_MPU60X0_LOWPASS_20_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_10) ? PIOS_MPU60X0_LOWPASS_10_HZ
: (hw_mpu6000_dlpf ==
HWCOLIBRI_MPU6000DLPF_5) ? PIOS_MPU60X0_LOWPASS_5_HZ :
pios_mpu6000_cfg.default_filter;
PIOS_MPU6000_SetLPF(mpu6000_dlpf);
uint8_t hw_mpu6000_samplerate;
HwColibriMPU6000RateGet(&hw_mpu6000_samplerate);
uint16_t mpu6000_samplerate =
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_200) ? 200 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_333) ? 333 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_500) ? 500 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_666) ? 666 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_1000) ? 1000 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_2000) ? 2000 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_4000) ? 4000 :
(hw_mpu6000_samplerate == HWCOLIBRI_MPU6000RATE_8000) ? 8000 :
pios_mpu6000_cfg.default_samplerate;
PIOS_MPU6000_SetSampleRate(mpu6000_samplerate);
#endif
#if defined(PIOS_INCLUDE_I2C)
#if defined(PIOS_INCLUDE_HMC5883)
{
uint8_t Magnetometer;
HwColibriMagnetometerGet(&Magnetometer);
if (Magnetometer == HWCOLIBRI_MAGNETOMETER_INTERNAL) {
if (PIOS_HMC5883_Init
(pios_i2c_internal_adapter_id,
&pios_hmc5883_internal_cfg) != 0)
panic(3);
if (PIOS_HMC5883_Test() != 0)
panic(3);
}
if (Magnetometer == HWCOLIBRI_MAGNETOMETER_EXTERNALI2CUART1
|| Magnetometer ==
HWCOLIBRI_MAGNETOMETER_EXTERNALI2CUART3) {
// setup sensor orientation
uint8_t ExtMagOrientation;
HwColibriExtMagOrientationGet(&ExtMagOrientation);
enum pios_hmc5883_orientation hmc5883_orientation =
(ExtMagOrientation ==
HWCOLIBRI_EXTMAGORIENTATION_TOP0DEGCW) ?
PIOS_HMC5883_TOP_0DEG : (ExtMagOrientation ==
HWCOLIBRI_EXTMAGORIENTATION_TOP90DEGCW)
? PIOS_HMC5883_TOP_90DEG : (ExtMagOrientation
==
HWCOLIBRI_EXTMAGORIENTATION_TOP180DEGCW)
? PIOS_HMC5883_TOP_180DEG : (ExtMagOrientation
==
HWCOLIBRI_EXTMAGORIENTATION_TOP270DEGCW)
? PIOS_HMC5883_TOP_270DEG : (ExtMagOrientation
==
HWCOLIBRI_EXTMAGORIENTATION_BOTTOM0DEGCW)
? PIOS_HMC5883_BOTTOM_0DEG : (ExtMagOrientation
==
HWCOLIBRI_EXTMAGORIENTATION_BOTTOM90DEGCW)
? PIOS_HMC5883_BOTTOM_90DEG
: (ExtMagOrientation ==
HWCOLIBRI_EXTMAGORIENTATION_BOTTOM180DEGCW)
? PIOS_HMC5883_BOTTOM_180DEG
: (ExtMagOrientation ==
HWCOLIBRI_EXTMAGORIENTATION_BOTTOM270DEGCW)
? PIOS_HMC5883_BOTTOM_270DEG :
pios_hmc5883_external_cfg.Default_Orientation;
PIOS_HMC5883_SetOrientation(hmc5883_orientation);
}
}
#endif
//I2C is slow, sensor init as well, reset watchdog to prevent reset here
PIOS_WDG_Clear();
#if defined(PIOS_INCLUDE_MS5611)
if (PIOS_MS5611_Init
(&pios_ms5611_cfg, pios_i2c_internal_adapter_id) != 0)
panic(4);
if (PIOS_MS5611_Test() != 0)
panic(4);
#endif
//I2C is slow, sensor init as well, reset watchdog to prevent reset here
PIOS_WDG_Clear();
#endif /* PIOS_INCLUDE_I2C */
#if defined(PIOS_INCLUDE_GPIO)
PIOS_GPIO_Init();
#endif
#if defined(PIOS_INCLUDE_ADC)
if (hw_rcvrport == HWCOLIBRI_RCVRPORT_PWMADC ||
hw_rcvrport == HWCOLIBRI_RCVRPORT_PPMADC ||
hw_rcvrport == HWCOLIBRI_RCVRPORT_PPMPWMADC ||
hw_rcvrport == HWCOLIBRI_RCVRPORT_OUTPUTSADC ||
hw_rcvrport == HWCOLIBRI_RCVRPORT_PPMOUTPUTSADC) {
uint32_t internal_adc_id;
PIOS_INTERNAL_ADC_Init(&internal_adc_id, &pios_adc_cfg);
PIOS_ADC_Init(&pios_internal_adc_id,
&pios_internal_adc_driver, internal_adc_id);
}
#endif
#if defined(PIOS_INCLUDE_FLASH)
if ( PIOS_STREAMFS_Init(&streamfs_id, &streamfs_settings, FLASH_PARTITION_LABEL_LOG) != 0)
panic(8);
const uint32_t LOG_BUF_LEN = 256;
uint8_t *log_rx_buffer = PIOS_malloc(LOG_BUF_LEN);
uint8_t *log_tx_buffer = PIOS_malloc(LOG_BUF_LEN);
if (PIOS_COM_Init(&pios_com_spiflash_logging_id, &pios_streamfs_com_driver, streamfs_id,
log_rx_buffer, LOG_BUF_LEN, log_tx_buffer, LOG_BUF_LEN) != 0)
panic(9);
#endif /* PIOS_INCLUDE_FLASH */
//Set battery input pin to floating as long as it is unused
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_15;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_ResetBits(GPIOC, GPIO_Pin_15);
//Set buzzer output to low as long as it is unused
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_ResetBits(GPIOA, GPIO_Pin_4);
/* Make sure we have at least one telemetry link configured or else fail initialization */
PIOS_Assert(pios_com_telem_rf_id || pios_com_telem_usb_id);
}
void PIOS_Board_Init(void) {
/* Delay system */
PIOS_DELAY_Init();
const struct pios_board_info * bdinfo = &pios_board_info_blob;
#if defined(PIOS_INCLUDE_LED)
const struct pios_led_cfg * led_cfg = PIOS_BOARD_HW_DEFS_GetLedCfg(bdinfo->board_rev);
PIOS_Assert(led_cfg);
PIOS_LED_Init(led_cfg);
#endif /* PIOS_INCLUDE_LED */
/* Set up the SPI interface to the gyro/acelerometer */
if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) {
PIOS_DEBUG_Assert(0);
}
/* Set up the SPI interface to the flash and rfm22b */
if (PIOS_SPI_Init(&pios_spi_telem_flash_id, &pios_spi_telem_flash_cfg)) {
PIOS_DEBUG_Assert(0);
}
#if defined(PIOS_INCLUDE_FLASH)
/* Inititialize all flash drivers */
if (PIOS_Flash_Jedec_Init(&pios_external_flash_id, pios_spi_telem_flash_id, 1, &flash_m25p_cfg) != 0)
panic(1);
if (PIOS_Flash_Internal_Init(&pios_internal_flash_id, &flash_internal_cfg) != 0)
panic(1);
/* Register the partition table */
const struct pios_flash_partition * flash_partition_table;
uint32_t num_partitions;
flash_partition_table = PIOS_BOARD_HW_DEFS_GetPartitionTable(bdinfo->board_rev, &num_partitions);
PIOS_FLASH_register_partition_table(flash_partition_table, num_partitions);
/* Mount all filesystems */
if (PIOS_FLASHFS_Logfs_Init(&pios_uavo_settings_fs_id, &flashfs_settings_cfg, FLASH_PARTITION_LABEL_SETTINGS) != 0)
panic(1);
if (PIOS_FLASHFS_Logfs_Init(&pios_waypoints_settings_fs_id, &flashfs_waypoints_cfg, FLASH_PARTITION_LABEL_WAYPOINTS) != 0)
panic(1);
#if defined(ERASE_FLASH)
PIOS_FLASHFS_Format(pios_uavo_settings_fs_id);
#endif
#endif /* PIOS_INCLUDE_FLASH */
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Initialize UAVObject libraries */
EventDispatcherInitialize();
UAVObjInitialize();
/* Initialize the alarms library */
AlarmsInitialize();
HwFreedomInitialize();
ModuleSettingsInitialize();
#if defined(PIOS_INCLUDE_RTC)
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
#ifndef ERASE_FLASH
/* Initialize watchdog as early as possible to catch faults during init
* but do it only if there is no debugger connected
*/
if ((CoreDebug->DHCSR & CoreDebug_DHCSR_C_DEBUGEN_Msk) == 0) {
PIOS_WDG_Init();
}
#endif
// /* Set up pulse timers */
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_2_cfg);
PIOS_TIM_InitClock(&tim_3_cfg);
/* IAP System Setup */
PIOS_IAP_Init();
uint16_t boot_count = PIOS_IAP_ReadBootCount();
if (boot_count < 3) {
PIOS_IAP_WriteBootCount(++boot_count);
AlarmsClear(SYSTEMALARMS_ALARM_BOOTFAULT);
} else {
/* Too many failed boot attempts, force hw config to defaults */
HwFreedomSetDefaults(HwFreedomHandle(), 0);
ModuleSettingsSetDefaults(ModuleSettingsHandle(),0);
AlarmsSet(SYSTEMALARMS_ALARM_BOOTFAULT, SYSTEMALARMS_ALARM_CRITICAL);
}
PIOS_IAP_Init();
#if defined(PIOS_INCLUDE_USB)
/* Initialize board specific USB data */
PIOS_USB_BOARD_DATA_Init();
/* Flags to determine if various USB interfaces are advertised */
bool usb_hid_present = false;
bool usb_cdc_present = false;
#if defined(PIOS_INCLUDE_USB_CDC)
if (PIOS_USB_DESC_HID_CDC_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
usb_cdc_present = true;
#else
if (PIOS_USB_DESC_HID_ONLY_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
#endif
uintptr_t pios_usb_id;
PIOS_USB_Init(&pios_usb_id, PIOS_BOARD_HW_DEFS_GetUsbCfg(bdinfo->board_rev));
#if defined(PIOS_INCLUDE_USB_CDC)
uint8_t hw_usb_vcpport;
/* Configure the USB VCP port */
HwFreedomUSB_VCPPortGet(&hw_usb_vcpport);
if (!usb_cdc_present) {
/* Force VCP port function to disabled if we haven't advertised VCP in our USB descriptor */
hw_usb_vcpport = HWFREEDOM_USB_VCPPORT_DISABLED;
}
uintptr_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
switch (hw_usb_vcpport) {
case HWFREEDOM_USB_VCPPORT_DISABLED:
break;
case HWFREEDOM_USB_VCPPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWFREEDOM_USB_VCPPORT_COMBRIDGE:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_vcp_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWFREEDOM_USB_VCPPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_COM)
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_debug_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
NULL, 0,
tx_buffer, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
#endif /* PIOS_INCLUDE_COM */
break;
case HWFREEDOM_USB_VCPPORT_PICOC:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_PICOC_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_PICOC_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_picoc_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_PICOC_RX_BUF_LEN,
tx_buffer, PIOS_COM_PICOC_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_CDC */
#if defined(PIOS_INCLUDE_USB_HID)
/* Configure the usb HID port */
uint8_t hw_usb_hidport;
HwFreedomUSB_HIDPortGet(&hw_usb_hidport);
if (!usb_hid_present) {
/* Force HID port function to disabled if we haven't advertised HID in our USB descriptor */
hw_usb_hidport = HWFREEDOM_USB_HIDPORT_DISABLED;
}
uintptr_t pios_usb_hid_id;
if (PIOS_USB_HID_Init(&pios_usb_hid_id, &pios_usb_hid_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
switch (hw_usb_hidport) {
case HWFREEDOM_USB_HIDPORT_DISABLED:
break;
case HWFREEDOM_USB_HIDPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_hid_com_driver, pios_usb_hid_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_HID */
if (usb_hid_present || usb_cdc_present) {
PIOS_USBHOOK_Activate();
}
#endif /* PIOS_INCLUDE_USB */
/* Configure IO ports */
uint8_t hw_DSMxBind;
HwFreedomDSMxBindGet(&hw_DSMxBind);
/* Configure FlexiPort */
uint8_t hw_mainport;
HwFreedomMainPortGet(&hw_mainport);
switch (hw_mainport) {
case HWFREEDOM_MAINPORT_DISABLED:
break;
case HWFREEDOM_MAINPORT_TELEMETRY:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_TELEM_RF_RX_BUF_LEN, PIOS_COM_TELEM_RF_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_telem_rf_id);
break;
case HWFREEDOM_MAINPORT_GPS:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_GPS_RX_BUF_LEN, PIOS_COM_GPS_RX_BUF_LEN, &pios_usart_com_driver, &pios_com_gps_id);
break;
case HWFREEDOM_MAINPORT_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
PIOS_Board_configure_dsm(&pios_usart_dsm_hsum_main_cfg, &pios_dsm_main_cfg,
&pios_usart_com_driver, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMMAINPORT,&hw_DSMxBind);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWFREEDOM_MAINPORT_HOTTSUMD:
case HWFREEDOM_MAINPORT_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_mainport) {
case HWFREEDOM_MAINPORT_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWFREEDOM_MAINPORT_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum(&pios_usart_dsm_hsum_main_cfg, &pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWFREEDOM_MAINPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
PIOS_Board_configure_com(&pios_usart_main_cfg, 0, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_debug_id);
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWFREEDOM_MAINPORT_COMBRIDGE:
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_BRIDGE_RX_BUF_LEN, PIOS_COM_BRIDGE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_bridge_id);
break;
case HWFREEDOM_MAINPORT_MAVLINKTX:
#if defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart_main_cfg, 0, PIOS_COM_MAVLINK_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWFREEDOM_MAINPORT_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_GPS)
#if defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_GPS_RX_BUF_LEN, PIOS_COM_MAVLINK_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
#endif /* PIOS_INCLUDE_GPS */
break;
case HWFREEDOM_MAINPORT_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_HOTT_RX_BUF_LEN, PIOS_COM_HOTT_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWFREEDOM_MAINPORT_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_main_cfg, 0, PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWFREEDOM_MAINPORT_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart_main_cfg, 0, PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_lighttelemetry_id);
#endif
break;
case HWFREEDOM_MAINPORT_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_PICOC_RX_BUF_LEN, PIOS_COM_PICOC_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
case HWFREEDOM_MAINPORT_FRSKYSPORTTELEMETRY:
#if defined(PIOS_INCLUDE_FRSKY_SPORT_TELEMETRY) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_main_cfg, PIOS_COM_FRSKYSPORT_RX_BUF_LEN, PIOS_COM_FRSKYSPORT_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_frsky_sport_id);
#endif /* PIOS_INCLUDE_FRSKY_SPORT_TELEMETRY */
break;
} /* hw_freedom_mainport */
/* Configure flexi USART port */
uint8_t hw_flexiport;
HwFreedomFlexiPortGet(&hw_flexiport);
switch (hw_flexiport) {
case HWFREEDOM_FLEXIPORT_DISABLED:
break;
case HWFREEDOM_FLEXIPORT_TELEMETRY:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_TELEM_RF_RX_BUF_LEN, PIOS_COM_TELEM_RF_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_telem_rf_id);
break;
case HWFREEDOM_FLEXIPORT_GPS:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_GPS_RX_BUF_LEN, PIOS_COM_GPS_RX_BUF_LEN, &pios_usart_com_driver, &pios_com_gps_id);
break;
case HWFREEDOM_FLEXIPORT_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
//TODO: Define the various Channelgroup for Revo dsm inputs and handle here
PIOS_Board_configure_dsm(&pios_usart_dsm_hsum_flexi_cfg, &pios_dsm_flexi_cfg,
&pios_usart_com_driver, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMFLEXIPORT,&hw_DSMxBind);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWFREEDOM_FLEXIPORT_HOTTSUMD:
case HWFREEDOM_FLEXIPORT_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_flexiport) {
case HWFREEDOM_FLEXIPORT_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWFREEDOM_FLEXIPORT_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum(&pios_usart_dsm_hsum_flexi_cfg, &pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWFREEDOM_FLEXIPORT_I2C:
#if defined(PIOS_INCLUDE_I2C)
{
if (PIOS_I2C_Init(&pios_i2c_flexiport_adapter_id, &pios_i2c_flexiport_adapter_cfg)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_I2C */
break;
case HWFREEDOM_FLEXIPORT_DEBUGCONSOLE:
#if defined(PIOS_INCLUDE_DEBUG_CONSOLE)
{
PIOS_Board_configure_com(&pios_usart_flexi_cfg, 0, PIOS_COM_DEBUGCONSOLE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_debug_id);
}
#endif /* PIOS_INCLUDE_DEBUG_CONSOLE */
break;
case HWFREEDOM_FLEXIPORT_COMBRIDGE:
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_BRIDGE_RX_BUF_LEN, PIOS_COM_BRIDGE_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_bridge_id);
break;
case HWFREEDOM_FLEXIPORT_MAVLINKTX:
#if defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, 0, PIOS_COM_MAVLINK_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_mavlink_id);
#endif /* PIOS_INCLUDE_MAVLINK */
break;
case HWFREEDOM_FLEXIPORT_MAVLINKTX_GPS_RX:
#if defined(PIOS_INCLUDE_GPS)
#if defined(PIOS_INCLUDE_MAVLINK)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_GPS_RX_BUF_LEN, PIOS_COM_MAVLINK_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_gps_id);
pios_com_mavlink_id = pios_com_gps_id;
#endif /* PIOS_INCLUDE_MAVLINK */
#endif /* PIOS_INCLUDE_GPS */
break;
case HWFREEDOM_FLEXIPORT_HOTTTELEMETRY:
#if defined(PIOS_INCLUDE_HOTT) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_HOTT_RX_BUF_LEN, PIOS_COM_HOTT_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_hott_id);
#endif /* PIOS_INCLUDE_HOTT */
break;
case HWFREEDOM_FLEXIPORT_FRSKYSENSORHUB:
#if defined(PIOS_INCLUDE_FRSKY_SENSOR_HUB) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, 0, PIOS_COM_FRSKYSENSORHUB_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_frsky_sensor_hub_id);
#endif /* PIOS_INCLUDE_FRSKY_SENSOR_HUB */
break;
case HWFREEDOM_FLEXIPORT_LIGHTTELEMETRYTX:
#if defined(PIOS_INCLUDE_LIGHTTELEMETRY)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, 0, PIOS_COM_LIGHTTELEMETRY_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_lighttelemetry_id);
#endif
break;
case HWFREEDOM_FLEXIPORT_PICOC:
#if defined(PIOS_INCLUDE_PICOC) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_PICOC_RX_BUF_LEN, PIOS_COM_PICOC_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_picoc_id);
#endif /* PIOS_INCLUDE_PICOC */
break;
case HWFREEDOM_FLEXIPORT_FRSKYSPORTTELEMETRY:
#if defined(PIOS_INCLUDE_FRSKY_SPORT_TELEMETRY) && defined(PIOS_INCLUDE_USART) && defined(PIOS_INCLUDE_COM)
PIOS_Board_configure_com(&pios_usart_flexi_cfg, PIOS_COM_FRSKYSPORT_RX_BUF_LEN, PIOS_COM_FRSKYSPORT_TX_BUF_LEN, &pios_usart_com_driver, &pios_com_frsky_sport_id);
#endif /* PIOS_INCLUDE_FRSKY_SPORT_TELEMETRY */
break;
} /* hw_freedom_flexiport */
/* Initalize the RFM22B radio COM device. */
#if defined(PIOS_INCLUDE_RFM22B)
RFM22BStatusInitialize();
RFM22BStatusCreateInstance();
// Initialize out status object.
RFM22BStatusData rfm22bstatus;
RFM22BStatusGet(&rfm22bstatus);
RFM22BStatusInstSet(1,&rfm22bstatus);
HwFreedomData hwFreedom;
HwFreedomGet(&hwFreedom);
// Initialize out status object.
rfm22bstatus.BoardType = bdinfo->board_type;
rfm22bstatus.BoardRevision = bdinfo->board_rev;
if (hwFreedom.Radio == HWFREEDOM_RADIO_DISABLED || hwFreedom.MaxRfPower == HWFREEDOM_MAXRFPOWER_0) {
// When radio disabled, it is ok for init to fail. This allows boards without populating
// this component.
const struct pios_rfm22b_cfg *rfm22b_cfg = PIOS_BOARD_HW_DEFS_GetRfm22Cfg(bdinfo->board_rev);
if (PIOS_RFM22B_Init(&pios_rfm22b_id, PIOS_RFM22_SPI_PORT, rfm22b_cfg->slave_num, rfm22b_cfg) == 0) {
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_0);
rfm22bstatus.DeviceID = PIOS_RFM22B_DeviceID(pios_rfm22b_id);
rfm22bstatus.BoardRevision = PIOS_RFM22B_ModuleVersion(pios_rfm22b_id);
} else {
pios_rfm22b_id = 0;
}
rfm22bstatus.LinkState = RFM22BSTATUS_LINKSTATE_DISABLED;
} else {
// always allow receiving PPM when radio is on
bool ppm_mode = hwFreedom.Radio == HWFREEDOM_RADIO_TELEMPPM || hwFreedom.Radio == HWFREEDOM_RADIO_PPM;
bool ppm_only = hwFreedom.Radio == HWFREEDOM_RADIO_PPM;
bool is_oneway = hwFreedom.Radio == HWFREEDOM_RADIO_PPM; // Sparky2 can only receive PPM only
/* Configure the RFM22B device. */
const struct pios_rfm22b_cfg *rfm22b_cfg = PIOS_BOARD_HW_DEFS_GetRfm22Cfg(bdinfo->board_rev);
if (PIOS_RFM22B_Init(&pios_rfm22b_id, PIOS_RFM22_SPI_PORT, rfm22b_cfg->slave_num, rfm22b_cfg)) {
panic(6);
}
rfm22bstatus.DeviceID = PIOS_RFM22B_DeviceID(pios_rfm22b_id);
rfm22bstatus.BoardRevision = PIOS_RFM22B_ModuleVersion(pios_rfm22b_id);
/* Configure the radio com interface */
uint8_t *rx_buffer = (uint8_t *)PIOS_malloc(PIOS_COM_RFM22B_RF_RX_BUF_LEN);
uint8_t *tx_buffer = (uint8_t *)PIOS_malloc(PIOS_COM_RFM22B_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_rf_id, &pios_rfm22b_com_driver, pios_rfm22b_id,
rx_buffer, PIOS_COM_RFM22B_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_RFM22B_RF_TX_BUF_LEN)) {
panic(6);
}
/* Set Telemetry to use RFM22b if no other telemetry is configured (USB always overrides anyway) */
if (!pios_com_telem_rf_id) {
pios_com_telem_rf_id = pios_com_rf_id;
}
rfm22bstatus.LinkState = RFM22BSTATUS_LINKSTATE_ENABLED;
enum rfm22b_datarate datarate = RFM22_datarate_64000;
switch (hwFreedom.MaxRfSpeed) {
case HWFREEDOM_MAXRFSPEED_9600:
datarate = RFM22_datarate_9600;
break;
case HWFREEDOM_MAXRFSPEED_19200:
datarate = RFM22_datarate_19200;
break;
case HWFREEDOM_MAXRFSPEED_32000:
datarate = RFM22_datarate_32000;
break;
case HWFREEDOM_MAXRFSPEED_64000:
datarate = RFM22_datarate_64000;
break;
case HWFREEDOM_MAXRFSPEED_100000:
datarate = RFM22_datarate_100000;
break;
case HWFREEDOM_MAXRFSPEED_192000:
datarate = RFM22_datarate_192000;
break;
}
/* Set the radio configuration parameters. */
PIOS_RFM22B_Config(pios_rfm22b_id, datarate, hwFreedom.MinChannel, hwFreedom.MaxChannel, hwFreedom.CoordID, is_oneway, ppm_mode, ppm_only);
/* Set the modem Tx poer level */
switch (hwFreedom.MaxRfPower) {
case HWFREEDOM_MAXRFPOWER_125:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_0);
break;
case HWFREEDOM_MAXRFPOWER_16:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_1);
break;
case HWFREEDOM_MAXRFPOWER_316:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_2);
break;
case HWFREEDOM_MAXRFPOWER_63:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_3);
break;
case HWFREEDOM_MAXRFPOWER_126:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_4);
break;
case HWFREEDOM_MAXRFPOWER_25:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_5);
break;
case HWFREEDOM_MAXRFPOWER_50:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_6);
break;
case HWFREEDOM_MAXRFPOWER_100:
PIOS_RFM22B_SetTxPower(pios_rfm22b_id, RFM22_tx_pwr_txpow_7);
break;
default:
// do nothing
break;
}
/* Reinitialize the modem. */
PIOS_RFM22B_Reinit(pios_rfm22b_id);
#if defined(PIOS_INCLUDE_RFM22B_RCVR)
{
uintptr_t pios_rfm22brcvr_id;
PIOS_RFM22B_Rcvr_Init(&pios_rfm22brcvr_id, pios_rfm22b_id);
uintptr_t pios_rfm22brcvr_rcvr_id;
if (PIOS_RCVR_Init(&pios_rfm22brcvr_rcvr_id, &pios_rfm22b_rcvr_driver, pios_rfm22brcvr_id)) {
panic(6);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_RFM22B] = pios_rfm22brcvr_rcvr_id;
}
}
RFM22BStatusInstSet(1,&rfm22bstatus);
#endif /* PIOS_INCLUDE_RFM22B_RCVR */
#endif /* PIOS_INCLUDE_RFM22B */
PIOS_WDG_Clear();
/* Configure input receiver USART port */
uint8_t hw_rcvrport;
HwFreedomRcvrPortGet(&hw_rcvrport);
switch (hw_rcvrport) {
case HWFREEDOM_RCVRPORT_DISABLED:
break;
case HWFREEDOM_RCVRPORT_PPM:
{
uintptr_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uintptr_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
break;
case HWFREEDOM_RCVRPORT_DSM:
#if defined(PIOS_INCLUDE_DSM)
{
//TODO: Define the various Channelgroup for Revo dsm inputs and handle here
PIOS_Board_configure_dsm(&pios_usart_dsm_hsum_rcvr_cfg, &pios_dsm_rcvr_cfg,
&pios_usart_com_driver, MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMRCVRPORT,&hw_DSMxBind);
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWFREEDOM_RCVRPORT_HOTTSUMD:
case HWFREEDOM_RCVRPORT_HOTTSUMH:
#if defined(PIOS_INCLUDE_HSUM)
{
enum pios_hsum_proto proto;
switch (hw_rcvrport) {
case HWFREEDOM_RCVRPORT_HOTTSUMD:
proto = PIOS_HSUM_PROTO_SUMD;
break;
case HWFREEDOM_RCVRPORT_HOTTSUMH:
proto = PIOS_HSUM_PROTO_SUMH;
break;
default:
PIOS_Assert(0);
break;
}
PIOS_Board_configure_hsum(&pios_usart_dsm_hsum_rcvr_cfg, &pios_usart_com_driver, &proto, MANUALCONTROLSETTINGS_CHANNELGROUPS_HOTTSUM);
}
#endif /* PIOS_INCLUDE_HSUM */
break;
case HWFREEDOM_RCVRPORT_SBUS:
#if defined(PIOS_INCLUDE_SBUS)
{
uintptr_t pios_usart_sbus_id;
if (PIOS_USART_Init(&pios_usart_sbus_id, &pios_usart_sbus_rcvr_cfg)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_id;
if (PIOS_SBus_Init(&pios_sbus_id, &pios_sbus_cfg, &pios_usart_com_driver, pios_usart_sbus_id)) {
PIOS_Assert(0);
}
uintptr_t pios_sbus_rcvr_id;
if (PIOS_RCVR_Init(&pios_sbus_rcvr_id, &pios_sbus_rcvr_driver, pios_sbus_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_SBUS] = pios_sbus_rcvr_id;
}
#endif
break;
}
if (hw_rcvrport != HWFREEDOM_RCVRPORT_SBUS) {
GPIO_Init(pios_sbus_cfg.inv.gpio, (GPIO_InitTypeDef*)&pios_sbus_cfg.inv.init);
GPIO_WriteBit(pios_sbus_cfg.inv.gpio, pios_sbus_cfg.inv.init.GPIO_Pin, pios_sbus_cfg.gpio_inv_disable);
}
#if defined(PIOS_OVERO_SPI)
/* Set up the SPI based PIOS_COM interface to the overo */
{
bool overo_enabled = false;
#ifdef MODULE_OveroSync_BUILTIN
overo_enabled = true;
#else
uint8_t module_state[MODULESETTINGS_ADMINSTATE_NUMELEM];
ModuleSettingsAdminStateGet(module_state);
if (module_state[MODULESETTINGS_ADMINSTATE_OVEROSYNC] == MODULESETTINGS_ADMINSTATE_ENABLED) {
overo_enabled = true;
} else {
overo_enabled = false;
}
#endif
if (overo_enabled) {
if (PIOS_OVERO_Init(&pios_overo_id, &pios_overo_cfg)) {
PIOS_DEBUG_Assert(0);
}
const uint32_t PACKET_SIZE = 1024;
uint8_t * rx_buffer = (uint8_t *) PIOS_malloc(PACKET_SIZE);
uint8_t * tx_buffer = (uint8_t *) PIOS_malloc(PACKET_SIZE);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_overo_id, &pios_overo_com_driver, pios_overo_id,
rx_buffer, PACKET_SIZE,
tx_buffer, PACKET_SIZE)) {
PIOS_Assert(0);
}
}
}
#endif
#if defined(PIOS_INCLUDE_GCSRCVR)
GCSReceiverInitialize();
uintptr_t pios_gcsrcvr_id;
PIOS_GCSRCVR_Init(&pios_gcsrcvr_id);
uintptr_t pios_gcsrcvr_rcvr_id;
if (PIOS_RCVR_Init(&pios_gcsrcvr_rcvr_id, &pios_gcsrcvr_rcvr_driver, pios_gcsrcvr_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_GCS] = pios_gcsrcvr_rcvr_id;
#endif /* PIOS_INCLUDE_GCSRCVR */
#ifndef PIOS_DEBUG_ENABLE_DEBUG_PINS
uint8_t hw_output_port;
HwFreedomOutputGet(&hw_output_port);
switch (hw_output_port) {
case HWFREEDOM_OUTPUT_DISABLED:
break;
case HWFREEDOM_OUTPUT_PWM:
/* Set up the servo outputs */
PIOS_Servo_Init(&pios_servo_cfg);
break;
default:
break;
}
#else
PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels));
#endif
PIOS_DELAY_WaitmS(200);
PIOS_SENSORS_Init();
#if defined(PIOS_INCLUDE_MPU6000)
if (PIOS_MPU6000_Init(pios_spi_gyro_id,0, &pios_mpu6000_cfg) != 0)
panic(2);
if (PIOS_MPU6000_Test() != 0)
panic(2);
// To be safe map from UAVO enum to driver enum
uint8_t hw_gyro_range;
HwFreedomGyroRangeGet(&hw_gyro_range);
switch(hw_gyro_range) {
case HWFREEDOM_GYRORANGE_250:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_250_DEG);
break;
case HWFREEDOM_GYRORANGE_500:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_500_DEG);
break;
case HWFREEDOM_GYRORANGE_1000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_1000_DEG);
break;
case HWFREEDOM_GYRORANGE_2000:
PIOS_MPU6000_SetGyroRange(PIOS_MPU60X0_SCALE_2000_DEG);
break;
}
uint8_t hw_accel_range;
HwFreedomAccelRangeGet(&hw_accel_range);
switch(hw_accel_range) {
case HWFREEDOM_ACCELRANGE_2G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_2G);
break;
case HWFREEDOM_ACCELRANGE_4G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_4G);
break;
case HWFREEDOM_ACCELRANGE_8G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_8G);
break;
case HWFREEDOM_ACCELRANGE_16G:
PIOS_MPU6000_SetAccelRange(PIOS_MPU60X0_ACCEL_16G);
break;
}
// the filter has to be set before rate else divisor calculation will fail
uint8_t hw_mpu6000_dlpf;
HwFreedomMPU6000DLPFGet(&hw_mpu6000_dlpf);
enum pios_mpu60x0_filter mpu6000_dlpf = \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_256) ? PIOS_MPU60X0_LOWPASS_256_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_188) ? PIOS_MPU60X0_LOWPASS_188_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_98) ? PIOS_MPU60X0_LOWPASS_98_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_42) ? PIOS_MPU60X0_LOWPASS_42_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_20) ? PIOS_MPU60X0_LOWPASS_20_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_10) ? PIOS_MPU60X0_LOWPASS_10_HZ : \
(hw_mpu6000_dlpf == HWFREEDOM_MPU6000DLPF_5) ? PIOS_MPU60X0_LOWPASS_5_HZ : \
pios_mpu6000_cfg.default_filter;
PIOS_MPU6000_SetLPF(mpu6000_dlpf);
uint8_t hw_mpu6000_samplerate;
HwFreedomMPU6000RateGet(&hw_mpu6000_samplerate);
uint16_t mpu6000_samplerate = \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_200) ? 200 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_333) ? 333 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_500) ? 500 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_666) ? 666 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_1000) ? 1000 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_2000) ? 2000 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_4000) ? 4000 : \
(hw_mpu6000_samplerate == HWFREEDOM_MPU6000RATE_8000) ? 8000 : \
pios_mpu6000_cfg.default_samplerate;
PIOS_MPU6000_SetSampleRate(mpu6000_samplerate);
#endif
if (PIOS_I2C_Init(&pios_i2c_mag_pressure_adapter_id, &pios_i2c_mag_pressure_adapter_cfg)) {
PIOS_DEBUG_Assert(0);
}
if (PIOS_I2C_CheckClear(pios_i2c_mag_pressure_adapter_id) != 0)
panic(5);
PIOS_DELAY_WaitmS(50);
#if defined(PIOS_INCLUDE_ADC)
uint32_t internal_adc_id;
PIOS_INTERNAL_ADC_Init(&internal_adc_id, &pios_adc_cfg);
PIOS_ADC_Init(&pios_internal_adc_id, &pios_internal_adc_driver, internal_adc_id);
#endif
PIOS_LED_On(0);
#if defined(PIOS_INCLUDE_HMC5883)
if (PIOS_HMC5883_Init(pios_i2c_mag_pressure_adapter_id, &pios_hmc5883_cfg) != 0)
panic(3);
#endif
PIOS_LED_On(1);
#if defined(PIOS_INCLUDE_MS5611)
if (PIOS_MS5611_Init(&pios_ms5611_cfg, pios_i2c_mag_pressure_adapter_id) != 0)
panic(4);
#endif
PIOS_LED_On(2);
}
void PIOS_Board_Init(void) {
/* Delay system */
PIOS_DELAY_Init();
const struct pios_board_info * bdinfo = &pios_board_info_blob;
#if defined(PIOS_INCLUDE_LED)
const struct pios_led_cfg * led_cfg = PIOS_BOARD_HW_DEFS_GetLedCfg(bdinfo->board_rev);
PIOS_Assert(led_cfg);
PIOS_LED_Init(led_cfg);
#endif /* PIOS_INCLUDE_LED */
#if defined(PIOS_INCLUDE_SPI)
/* Set up the SPI interface to the serial flash */
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
if (PIOS_SPI_Init(&pios_spi_flash_accel_id, &pios_spi_flash_accel_cfg_cc)) {
PIOS_Assert(0);
}
break;
case BOARD_REVISION_CC3D:
if (PIOS_SPI_Init(&pios_spi_flash_accel_id, &pios_spi_flash_accel_cfg_cc3d)) {
PIOS_Assert(0);
}
break;
default:
PIOS_Assert(0);
}
#endif
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
PIOS_Flash_Jedec_Init(pios_spi_flash_accel_id, 1, &flash_w25x_cfg);
PIOS_FLASHFS_Init(&flashfs_w25x_cfg);
break;
case BOARD_REVISION_CC3D:
PIOS_Flash_Jedec_Init(pios_spi_flash_accel_id, 0, &flash_m25p_cfg);
PIOS_FLASHFS_Init(&flashfs_m25p_cfg);
break;
default:
PIOS_DEBUG_Assert(0);
}
/* Initialize UAVObject libraries */
EventDispatcherInitialize();
UAVObjInitialize();
#if defined(PIOS_INCLUDE_RTC)
/* Initialize the real-time clock and its associated tick */
PIOS_RTC_Init(&pios_rtc_main_cfg);
#endif
HwSettingsInitialize();
#ifndef ERASE_FLASH
/* Initialize watchdog as early as possible to catch faults during init */
PIOS_WDG_Init();
#endif
/* Initialize the alarms library */
AlarmsInitialize();
/* Check for repeated boot failures */
PIOS_IAP_Init();
uint16_t boot_count = PIOS_IAP_ReadBootCount();
if (boot_count < 3) {
PIOS_IAP_WriteBootCount(++boot_count);
AlarmsClear(SYSTEMALARMS_ALARM_BOOTFAULT);
} else {
/* Too many failed boot attempts, force hwsettings to defaults */
HwSettingsSetDefaults(HwSettingsHandle(), 0);
AlarmsSet(SYSTEMALARMS_ALARM_BOOTFAULT, SYSTEMALARMS_ALARM_CRITICAL);
}
/* Initialize the task monitor library */
TaskMonitorInitialize();
/* Set up pulse timers */
PIOS_TIM_InitClock(&tim_1_cfg);
PIOS_TIM_InitClock(&tim_2_cfg);
PIOS_TIM_InitClock(&tim_3_cfg);
PIOS_TIM_InitClock(&tim_4_cfg);
#if defined(PIOS_INCLUDE_USB)
/* Initialize board specific USB data */
PIOS_USB_BOARD_DATA_Init();
/* Flags to determine if various USB interfaces are advertised */
bool usb_hid_present = false;
bool usb_cdc_present = false;
#if defined(PIOS_INCLUDE_USB_CDC)
if (PIOS_USB_DESC_HID_CDC_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
usb_cdc_present = true;
#else
if (PIOS_USB_DESC_HID_ONLY_Init()) {
PIOS_Assert(0);
}
usb_hid_present = true;
#endif
uint32_t pios_usb_id;
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
PIOS_USB_Init(&pios_usb_id, &pios_usb_main_cfg_cc);
break;
case BOARD_REVISION_CC3D:
PIOS_USB_Init(&pios_usb_id, &pios_usb_main_cfg_cc3d);
break;
default:
PIOS_Assert(0);
}
#if defined(PIOS_INCLUDE_USB_CDC)
uint8_t hwsettings_usb_vcpport;
/* Configure the USB VCP port */
HwSettingsUSB_VCPPortGet(&hwsettings_usb_vcpport);
if (!usb_cdc_present) {
/* Force VCP port function to disabled if we haven't advertised VCP in our USB descriptor */
hwsettings_usb_vcpport = HWSETTINGS_USB_VCPPORT_DISABLED;
}
switch (hwsettings_usb_vcpport) {
case HWSETTINGS_USB_VCPPORT_DISABLED:
break;
case HWSETTINGS_USB_VCPPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint32_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWSETTINGS_USB_VCPPORT_COMBRIDGE:
#if defined(PIOS_INCLUDE_COM)
{
uint32_t pios_usb_cdc_id;
if (PIOS_USB_CDC_Init(&pios_usb_cdc_id, &pios_usb_cdc_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_vcp_id, &pios_usb_cdc_com_driver, pios_usb_cdc_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
}
#endif /* PIOS_INCLUDE_USB_CDC */
#if defined(PIOS_INCLUDE_USB_HID)
/* Configure the usb HID port */
uint8_t hwsettings_usb_hidport;
HwSettingsUSB_HIDPortGet(&hwsettings_usb_hidport);
if (!usb_hid_present) {
/* Force HID port function to disabled if we haven't advertised HID in our USB descriptor */
hwsettings_usb_hidport = HWSETTINGS_USB_HIDPORT_DISABLED;
}
switch (hwsettings_usb_hidport) {
case HWSETTINGS_USB_HIDPORT_DISABLED:
break;
case HWSETTINGS_USB_HIDPORT_USBTELEMETRY:
#if defined(PIOS_INCLUDE_COM)
{
uint32_t pios_usb_hid_id;
if (PIOS_USB_HID_Init(&pios_usb_hid_id, &pios_usb_hid_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_USB_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_usb_id, &pios_usb_hid_com_driver, pios_usb_hid_id,
rx_buffer, PIOS_COM_TELEM_USB_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_USB_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_COM */
break;
case HWSETTINGS_USB_HIDPORT_RCTRANSMITTER:
#if defined(PIOS_INCLUDE_USB_RCTX)
{
if (PIOS_USB_RCTX_Init(&pios_usb_rctx_id, &pios_usb_rctx_cfg, pios_usb_id)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_USB_RCTX */
break;
}
#endif /* PIOS_INCLUDE_USB_HID */
#endif /* PIOS_INCLUDE_USB */
/* Configure the main IO port */
uint8_t hwsettings_DSMxBind;
HwSettingsDSMxBindGet(&hwsettings_DSMxBind);
uint8_t hwsettings_cc_mainport;
HwSettingsCC_MainPortGet(&hwsettings_cc_mainport);
switch (hwsettings_cc_mainport) {
case HWSETTINGS_CC_MAINPORT_DISABLED:
break;
case HWSETTINGS_CC_MAINPORT_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF)
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWSETTINGS_CC_MAINPORT_SBUS:
#if defined(PIOS_INCLUDE_SBUS)
{
uint32_t pios_usart_sbus_id;
if (PIOS_USART_Init(&pios_usart_sbus_id, &pios_usart_sbus_main_cfg)) {
PIOS_Assert(0);
}
uint32_t pios_sbus_id;
if (PIOS_SBus_Init(&pios_sbus_id, &pios_sbus_cfg, &pios_usart_com_driver, pios_usart_sbus_id)) {
PIOS_Assert(0);
}
uint32_t pios_sbus_rcvr_id;
if (PIOS_RCVR_Init(&pios_sbus_rcvr_id, &pios_sbus_rcvr_driver, pios_sbus_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_SBUS] = pios_sbus_rcvr_id;
}
#endif /* PIOS_INCLUDE_SBUS */
break;
case HWSETTINGS_CC_MAINPORT_GPS:
#if defined(PIOS_INCLUDE_GPS)
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_GPS_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
NULL, 0)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_GPS */
break;
case HWSETTINGS_CC_MAINPORT_DSM2:
case HWSETTINGS_CC_MAINPORT_DSMX10BIT:
case HWSETTINGS_CC_MAINPORT_DSMX11BIT:
#if defined(PIOS_INCLUDE_DSM)
{
enum pios_dsm_proto proto;
switch (hwsettings_cc_mainport) {
case HWSETTINGS_CC_MAINPORT_DSM2:
proto = PIOS_DSM_PROTO_DSM2;
break;
case HWSETTINGS_CC_MAINPORT_DSMX10BIT:
proto = PIOS_DSM_PROTO_DSMX10BIT;
break;
case HWSETTINGS_CC_MAINPORT_DSMX11BIT:
proto = PIOS_DSM_PROTO_DSMX11BIT;
break;
default:
PIOS_Assert(0);
break;
}
uint32_t pios_usart_dsm_id;
if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_main_cfg)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_id;
if (PIOS_DSM_Init(&pios_dsm_id,
&pios_dsm_main_cfg,
&pios_usart_com_driver,
pios_usart_dsm_id,
proto, 0)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_rcvr_id;
if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMMAINPORT] = pios_dsm_rcvr_id;
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWSETTINGS_CC_MAINPORT_COMAUX:
break;
case HWSETTINGS_CC_MAINPORT_COMBRIDGE:
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_main_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_bridge_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
break;
}
/* Configure the flexi port */
uint8_t hwsettings_cc_flexiport;
HwSettingsCC_FlexiPortGet(&hwsettings_cc_flexiport);
switch (hwsettings_cc_flexiport) {
case HWSETTINGS_CC_FLEXIPORT_DISABLED:
break;
case HWSETTINGS_CC_FLEXIPORT_TELEMETRY:
#if defined(PIOS_INCLUDE_TELEMETRY_RF)
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_TELEM_RF_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_telem_rf_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_TELEM_RF_RX_BUF_LEN,
tx_buffer, PIOS_COM_TELEM_RF_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_TELEMETRY_RF */
break;
case HWSETTINGS_CC_FLEXIPORT_COMBRIDGE:
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_RX_BUF_LEN);
uint8_t * tx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_BRIDGE_TX_BUF_LEN);
PIOS_Assert(rx_buffer);
PIOS_Assert(tx_buffer);
if (PIOS_COM_Init(&pios_com_bridge_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_BRIDGE_RX_BUF_LEN,
tx_buffer, PIOS_COM_BRIDGE_TX_BUF_LEN)) {
PIOS_Assert(0);
}
}
break;
case HWSETTINGS_CC_FLEXIPORT_GPS:
#if defined(PIOS_INCLUDE_GPS)
{
uint32_t pios_usart_generic_id;
if (PIOS_USART_Init(&pios_usart_generic_id, &pios_usart_generic_flexi_cfg)) {
PIOS_Assert(0);
}
uint8_t * rx_buffer = (uint8_t *) pvPortMalloc(PIOS_COM_GPS_RX_BUF_LEN);
PIOS_Assert(rx_buffer);
if (PIOS_COM_Init(&pios_com_gps_id, &pios_usart_com_driver, pios_usart_generic_id,
rx_buffer, PIOS_COM_GPS_RX_BUF_LEN,
NULL, 0)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_GPS */
break;
case HWSETTINGS_CC_FLEXIPORT_DSM2:
case HWSETTINGS_CC_FLEXIPORT_DSMX10BIT:
case HWSETTINGS_CC_FLEXIPORT_DSMX11BIT:
#if defined(PIOS_INCLUDE_DSM)
{
enum pios_dsm_proto proto;
switch (hwsettings_cc_flexiport) {
case HWSETTINGS_CC_FLEXIPORT_DSM2:
proto = PIOS_DSM_PROTO_DSM2;
break;
case HWSETTINGS_CC_FLEXIPORT_DSMX10BIT:
proto = PIOS_DSM_PROTO_DSMX10BIT;
break;
case HWSETTINGS_CC_FLEXIPORT_DSMX11BIT:
proto = PIOS_DSM_PROTO_DSMX11BIT;
break;
default:
PIOS_Assert(0);
break;
}
uint32_t pios_usart_dsm_id;
if (PIOS_USART_Init(&pios_usart_dsm_id, &pios_usart_dsm_flexi_cfg)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_id;
if (PIOS_DSM_Init(&pios_dsm_id,
&pios_dsm_flexi_cfg,
&pios_usart_com_driver,
pios_usart_dsm_id,
proto, hwsettings_DSMxBind)) {
PIOS_Assert(0);
}
uint32_t pios_dsm_rcvr_id;
if (PIOS_RCVR_Init(&pios_dsm_rcvr_id, &pios_dsm_rcvr_driver, pios_dsm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_DSMFLEXIPORT] = pios_dsm_rcvr_id;
}
#endif /* PIOS_INCLUDE_DSM */
break;
case HWSETTINGS_CC_FLEXIPORT_COMAUX:
break;
case HWSETTINGS_CC_FLEXIPORT_I2C:
#if defined(PIOS_INCLUDE_I2C)
{
if (PIOS_I2C_Init(&pios_i2c_flexi_adapter_id, &pios_i2c_flexi_adapter_cfg)) {
PIOS_Assert(0);
}
}
#endif /* PIOS_INCLUDE_I2C */
break;
}
/* Configure the rcvr port */
uint8_t hwsettings_rcvrport;
HwSettingsCC_RcvrPortGet(&hwsettings_rcvrport);
switch (hwsettings_rcvrport) {
case HWSETTINGS_CC_RCVRPORT_DISABLED:
break;
case HWSETTINGS_CC_RCVRPORT_PWM:
#if defined(PIOS_INCLUDE_PWM)
{
uint32_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_cfg);
uint32_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
case HWSETTINGS_CC_RCVRPORT_PPM:
case HWSETTINGS_CC_RCVRPORT_PPMOUTPUTS:
#if defined(PIOS_INCLUDE_PPM)
{
uint32_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uint32_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
break;
case HWSETTINGS_CC_RCVRPORT_PPMPWM:
/* This is a combination of PPM and PWM inputs */
#if defined(PIOS_INCLUDE_PPM)
{
uint32_t pios_ppm_id;
PIOS_PPM_Init(&pios_ppm_id, &pios_ppm_cfg);
uint32_t pios_ppm_rcvr_id;
if (PIOS_RCVR_Init(&pios_ppm_rcvr_id, &pios_ppm_rcvr_driver, pios_ppm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PPM] = pios_ppm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PPM */
#if defined(PIOS_INCLUDE_PWM)
{
uint32_t pios_pwm_id;
PIOS_PWM_Init(&pios_pwm_id, &pios_pwm_with_ppm_cfg);
uint32_t pios_pwm_rcvr_id;
if (PIOS_RCVR_Init(&pios_pwm_rcvr_id, &pios_pwm_rcvr_driver, pios_pwm_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_PWM] = pios_pwm_rcvr_id;
}
#endif /* PIOS_INCLUDE_PWM */
break;
}
#if defined(PIOS_INCLUDE_GCSRCVR)
GCSReceiverInitialize();
uint32_t pios_gcsrcvr_id;
PIOS_GCSRCVR_Init(&pios_gcsrcvr_id);
uint32_t pios_gcsrcvr_rcvr_id;
if (PIOS_RCVR_Init(&pios_gcsrcvr_rcvr_id, &pios_gcsrcvr_rcvr_driver, pios_gcsrcvr_id)) {
PIOS_Assert(0);
}
pios_rcvr_group_map[MANUALCONTROLSETTINGS_CHANNELGROUPS_GCS] = pios_gcsrcvr_rcvr_id;
#endif /* PIOS_INCLUDE_GCSRCVR */
/* Remap AFIO pin for PB4 (Servo 5 Out)*/
GPIO_PinRemapConfig( GPIO_Remap_SWJ_NoJTRST, ENABLE);
#ifndef PIOS_DEBUG_ENABLE_DEBUG_PINS
switch (hwsettings_rcvrport) {
case HWSETTINGS_CC_RCVRPORT_DISABLED:
case HWSETTINGS_CC_RCVRPORT_PWM:
case HWSETTINGS_CC_RCVRPORT_PPM:
case HWSETTINGS_CC_RCVRPORT_PPMPWM:
PIOS_Servo_Init(&pios_servo_cfg);
break;
case HWSETTINGS_CC_RCVRPORT_PPMOUTPUTS:
case HWSETTINGS_CC_RCVRPORT_OUTPUTS:
PIOS_Servo_Init(&pios_servo_rcvr_cfg);
break;
}
#else
PIOS_DEBUG_Init(&pios_tim_servo_all_channels, NELEMENTS(pios_tim_servo_all_channels));
#endif /* PIOS_DEBUG_ENABLE_DEBUG_PINS */
switch(bdinfo->board_rev) {
case BOARD_REVISION_CC:
// Revision 1 with invensense gyros, start the ADC
#if defined(PIOS_INCLUDE_ADC)
PIOS_ADC_Init(&pios_adc_cfg);
#endif
#if defined(PIOS_INCLUDE_ADXL345)
PIOS_ADXL345_Init(pios_spi_flash_accel_id, 0);
#endif
break;
case BOARD_REVISION_CC3D:
// Revision 2 with L3GD20 gyros, start a SPI interface and connect to it
GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
#if defined(PIOS_INCLUDE_MPU6000)
// Set up the SPI interface to the serial flash
if (PIOS_SPI_Init(&pios_spi_gyro_id, &pios_spi_gyro_cfg)) {
PIOS_Assert(0);
}
PIOS_MPU6000_Init(pios_spi_gyro_id,0,&pios_mpu6000_cfg);
init_test = PIOS_MPU6000_Test();
#endif /* PIOS_INCLUDE_MPU6000 */
break;
default:
PIOS_Assert(0);
}
PIOS_GPIO_Init();
/* Make sure we have at least one telemetry link configured or else fail initialization */
PIOS_Assert(pios_com_telem_rf_id || pios_com_telem_usb_id);
}
