static void pm8917_gpio_set_backlight(int bl_level)
{
int gpio24 = PM8917_GPIO_PM_TO_SYS(24);
if (bl_level > 0)
gpio_set_value_cansleep(gpio24, 1);
else
gpio_set_value_cansleep(gpio24, 0);
}
static int mipi_dsi_cdp_panel_power(int on)
{
static struct regulator *reg_l8, *reg_l23, *reg_l2;
/* Control backlight GPIO (24) directly when using PM8917 */
#ifndef CONFIG_FB_MSM_MIPI_WARPLTE_OTM_VIDEO_WVGA_PT_PANEL
int gpio24 = PM8917_GPIO_PM_TO_SYS(24);
#endif
int rc;
printk("lizhiye, %s: state : %d, dsi_power_on = %d\n", __func__, on, dsi_power_on);
if (!dsi_power_on) {
reg_l8 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vdc");
if (IS_ERR(reg_l8)) {
pr_err("could not get 8038_l8, rc = %ld\n",
PTR_ERR(reg_l8));
return -ENODEV;
}
reg_l23 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vddio");
if (IS_ERR(reg_l23)) {
pr_err("could not get 8038_l23, rc = %ld\n",
PTR_ERR(reg_l23));
return -ENODEV;
}
reg_l2 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vdda");
if (IS_ERR(reg_l2)) {
pr_err("could not get 8038_l2, rc = %ld\n",
PTR_ERR(reg_l2));
return -ENODEV;
}
rc = regulator_set_voltage(reg_l8, 2800000, 3000000);
if (rc) {
pr_err("set_voltage l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_voltage(reg_l23, 1800000, 1800000);
if (rc) {
pr_err("set_voltage l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_voltage(reg_l2, 1200000, 1200000);
if (rc) {
pr_err("set_voltage l2 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = gpio_request(DISP_RST_GPIO, "disp_rst_n");
if (rc) {
pr_err("request gpio DISP_RST_GPIO failed, rc=%d\n",
rc);
gpio_free(DISP_RST_GPIO);
return -ENODEV;
}
#ifdef CONFIG_FB_MSM_MIPI_WARPLTE_OTM_VIDEO_WVGA_PT_PANEL
rc = gpio_request(DISP_BACKLIGHT_GPIO, "disp_rst_n");
if (rc) {
pr_err("lizhiye, request gpio DISP_BACKLIGHT_GPIO failed, rc=%d\n",
rc);
gpio_free(DISP_BACKLIGHT_GPIO);
return -ENODEV;
}
#endif
rc = gpio_request(DISP_3D_2D_MODE, "disp_3d_2d");
if (rc) {
pr_err("request gpio DISP_3D_2D_MODE failed, rc=%d\n",
rc);
gpio_free(DISP_3D_2D_MODE);
return -ENODEV;
}
rc = gpio_direction_output(DISP_3D_2D_MODE, 0);
if (rc) {
pr_err("gpio_direction_output failed for %d gpio rc=%d\n",
DISP_3D_2D_MODE, rc);
return -ENODEV;
}
#ifndef CONFIG_FB_MSM_MIPI_WARPLTE_OTM_VIDEO_WVGA_PT_PANEL
if (socinfo_get_pmic_model() == PMIC_MODEL_PM8917) {
rc = gpio_request(gpio24, "disp_bl");
if (rc) {
pr_err("request for gpio 24 failed, rc=%d\n",
rc);
return -ENODEV;
}
gpio_set_value_cansleep(gpio24, 0);
novatek_pdata.gpio_set_backlight =
pm8917_gpio_set_backlight;
}
#endif
dsi_power_on = true;
}
if (on) {
rc = regulator_set_optimum_mode(reg_l8, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l23, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l2, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l2 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_enable(reg_l8);
if (rc) {
pr_err("enable l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_enable(reg_l23);
if (rc) {
pr_err("enable l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_enable(reg_l2);
if (rc) {
pr_err("enable l2 failed, rc=%d\n", rc);
return -ENODEV;
}
usleep(10000);
#if 0
gpio_set_value(DISP_RST_GPIO, 1);
usleep(10);
gpio_set_value(DISP_RST_GPIO, 0);
usleep(20);
gpio_set_value(DISP_RST_GPIO, 1);
#endif
gpio_set_value(DISP_3D_2D_MODE, 1);
usleep(20);
#ifndef CONFIG_FB_MSM_MIPI_WARPLTE_OTM_VIDEO_WVGA_PT_PANEL
if (socinfo_get_pmic_model() == PMIC_MODEL_PM8917)
gpio_set_value_cansleep(gpio24, 1);
#endif
} else {
gpio_set_value(DISP_RST_GPIO, 0);
rc = regulator_disable(reg_l2);
if (rc) {
pr_err("disable reg_l2 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_disable(reg_l8);
if (rc) {
pr_err("disable reg_l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_disable(reg_l23);
if (rc) {
pr_err("disable reg_l23 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_set_optimum_mode(reg_l8, 100);
if (rc < 0) {
pr_err("set_optimum_mode l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l23, 100);
if (rc < 0) {
pr_err("set_optimum_mode l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l2, 100);
if (rc < 0) {
pr_err("set_optimum_mode l2 failed, rc=%d\n", rc);
return -EINVAL;
}
gpio_set_value(DISP_3D_2D_MODE, 0);
usleep(20);
#ifndef CONFIG_FB_MSM_MIPI_WARPLTE_OTM_VIDEO_WVGA_PT_PANEL
if (socinfo_get_pmic_model() == PMIC_MODEL_PM8917)
gpio_set_value_cansleep(gpio24, 0);
#endif
}
return 0;
}
static int mipi_dsi_cdp_panel_power(int on)
{
static struct regulator *reg_l8, *reg_l23, *reg_l2;
/* Control backlight GPIO (24) directly when using PM8917 */
int gpio24 = PM8917_GPIO_PM_TO_SYS(24);
int rc;
pr_debug("%s: state : %d\n", __func__, on);
if (!dsi_power_on) {
reg_l8 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vdc");
if (IS_ERR(reg_l8)) {
pr_err("could not get 8038_l8, rc = %ld\n",
PTR_ERR(reg_l8));
return -ENODEV;
}
reg_l23 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vddio");
if (IS_ERR(reg_l23)) {
pr_err("could not get 8038_l23, rc = %ld\n",
PTR_ERR(reg_l23));
return -ENODEV;
}
reg_l2 = regulator_get(&msm_mipi_dsi1_device.dev,
"dsi_vdda");
if (IS_ERR(reg_l2)) {
pr_err("could not get 8038_l2, rc = %ld\n",
PTR_ERR(reg_l2));
return -ENODEV;
}
rc = regulator_set_voltage(reg_l8, 2800000, 3000000);
if (rc) {
pr_err("set_voltage l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_voltage(reg_l23, 1800000, 1800000);
if (rc) {
pr_err("set_voltage l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_voltage(reg_l2, 1200000, 1200000);
if (rc) {
pr_err("set_voltage l2 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = gpio_request(DISP_RST_GPIO, "disp_rst_n");
if (rc) {
pr_err("request gpio DISP_RST_GPIO failed, rc=%d\n",
rc);
gpio_free(DISP_RST_GPIO);
return -ENODEV;
}
if (machine_is_msm8930_evt()) {
rc = gpio_direction_output(DISP_RST_GPIO, 1);
if (rc) {
pr_err("gpio_direction_output failed for %d gpio rc=%d\n",
DISP_RST_GPIO, rc);
return -ENODEV;
}
}
if (!machine_is_msm8930_evt()) {
rc = gpio_request(DISP_3D_2D_MODE, "disp_3d_2d");
if (rc) {
pr_err("request gpio DISP_3D_2D_MODE failed, rc=%d\n",
rc);
gpio_free(DISP_3D_2D_MODE);
return -ENODEV;
}
rc = gpio_direction_output(DISP_3D_2D_MODE, 0);
if (rc) {
pr_err("gpio_direction_output failed for %d gpio rc=%d\n",
DISP_3D_2D_MODE, rc);
return -ENODEV;
}
}
if (socinfo_get_pmic_model() == PMIC_MODEL_PM8917) {
rc = gpio_request(gpio24, "disp_bl");
if (rc) {
pr_err("request for gpio 24 failed, rc=%d\n",
rc);
return -ENODEV;
}
gpio_set_value_cansleep(gpio24, 0);
novatek_pdata.gpio_set_backlight =
pm8917_gpio_set_backlight;
}
dsi_power_on = true;
}
if (on) {
rc = regulator_set_optimum_mode(reg_l8, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l23, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l2, 100000);
if (rc < 0) {
pr_err("set_optimum_mode l2 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_enable(reg_l8);
if (rc) {
pr_err("enable l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_enable(reg_l23);
if (rc) {
pr_err("enable l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_enable(reg_l2);
if (rc) {
pr_err("enable l2 failed, rc=%d\n", rc);
return -ENODEV;
}
usleep(10000);
gpio_set_value(DISP_RST_GPIO, 1);
usleep(10);
gpio_set_value(DISP_RST_GPIO, 0);
usleep(20);
gpio_set_value(DISP_RST_GPIO, 1);
if (!machine_is_msm8930_evt())
gpio_set_value(DISP_3D_2D_MODE, 1);
usleep(20);
} else {
gpio_set_value(DISP_RST_GPIO, 0);
rc = regulator_disable(reg_l2);
if (rc) {
pr_err("disable reg_l2 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_disable(reg_l8);
if (rc) {
pr_err("disable reg_l8 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_disable(reg_l23);
if (rc) {
pr_err("disable reg_l23 failed, rc=%d\n", rc);
return -ENODEV;
}
rc = regulator_set_optimum_mode(reg_l8, 100);
if (rc < 0) {
pr_err("set_optimum_mode l8 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l23, 100);
if (rc < 0) {
pr_err("set_optimum_mode l23 failed, rc=%d\n", rc);
return -EINVAL;
}
rc = regulator_set_optimum_mode(reg_l2, 100);
if (rc < 0) {
pr_err("set_optimum_mode l2 failed, rc=%d\n", rc);
return -EINVAL;
}
if (!machine_is_msm8930_evt())
gpio_set_value(DISP_3D_2D_MODE, 0);
usleep(20);
}
return 0;
}
