/*
* main.c
*/
int main(void) {
float fTemperature, fHumidity;
int32_t i32IntegerPart;
int32_t i32FractionPart;
g_ui32SysClock = SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN |
SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//confiugre the GPIO pins
PinoutSet(false,false);
ConfigureUART();
//configure I2C pins
SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C8);
GPIOPinConfigure(GPIO_PA2_I2C8SCL);
GPIOPinConfigure(GPIO_PA3_I2C8SDA);
GPIOPinTypeI2C(GPIO_PORTA_BASE,GPIO_PIN_2);
GPIOPinTypeI2C(GPIO_PORTA_BASE,GPIO_PIN_3);
//enable interrupts
IntMasterEnable();
//initialize I2C
I2CMInit(&g_sI2CInst,I2C8_BASE,INT_I2C8,0xff,0xff,g_ui32SysClock);
IntPrioritySet(INT_I2C7,0xE0);
//initialize the sensors
SHT21Init(&g_sSHT21Inst, &g_sI2CInst, SHT21_I2C_ADDRESS,
SHT21AppCallback,&g_sSHT21Inst);
//delay for 20 ms
SysCtlDelay(g_ui32SysClock / (50 * 3));
while(1){
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Write the command to start a humidity measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_RH, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Wait 33 milliseconds before attempting to get the result. Datasheet
// claims this can take as long as 29 milliseconds.
//
SysCtlDelay(g_ui32SysClock / (30 * 3));
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Get the raw data from the sensor over the I2C bus.
//
SHT21DataRead(&g_sSHT21Inst, SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Get a copy of the most recent raw data in floating point format.
//
SHT21DataHumidityGetFloat(&g_sSHT21Inst, &fHumidity);
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Write the command to start a temperature measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_T, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Wait 100 milliseconds before attempting to get the result. Datasheet
// claims this can take as long as 85 milliseconds.
//
SysCtlDelay(g_ui32SysClock / (10 * 3));
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Read the conversion data from the sensor over I2C.
//
SHT21DataRead(&g_sSHT21Inst, SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Get the most recent temperature result as a float in celcius.
//
SHT21DataTemperatureGetFloat(&g_sSHT21Inst, &fTemperature);
//
// Convert the floats to an integer part and fraction part for easy
// print. Humidity is returned as 0.0 to 1.0 so multiply by 100 to get
// percent humidity.
//
fHumidity *= 100.0f;
i32IntegerPart = (int32_t) fHumidity;
i32FractionPart = (int32_t) (fHumidity * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the humidity value using the integers we just created.
//
UARTprintf("Humidity %3d.%03d\t", i32IntegerPart, i32FractionPart);
//
// Perform the conversion from float to a printable set of integers.
//
i32IntegerPart = (int32_t) fTemperature;
i32FractionPart = (int32_t) (fTemperature * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the temperature as integer and fraction parts.
//
UARTprintf("Temperature %3d.%03d\n", i32IntegerPart, i32FractionPart);
//
// Delay for one second. This is to keep sensor duty cycle
// to about 10% as suggested in the datasheet, section 2.4.
// This minimizes self heating effects and keeps reading more accurate.
//
SysCtlDelay(g_ui32SysClock / 3);
}
return 0;
}
void SHT21AppCallback(void *pvCallbackData, unsigned int ui8Status)
{
float fTemperature, fHumidity;
unsigned char tempString[30]={0};
if(ui8Status == I2CM_STATUS_SUCCESS&&sensorTurn==3)
{
if(flag==0)
{
//
// Get the most recent temperature result as a float in celcius.
//
SHT21DataTemperatureGetFloat(&g_sSHT21Inst, &fTemperature);
flag=(flag+1)%3;
//
// Write the command to start a humidity measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_RH, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
SysCtlDelay(g_SysClock / (100 * 3));
//
// Perform the conversion from float to a printable set of integers.
//
SHT21_i32IntegerPart2 = (int32_t) fTemperature;
SHT21_i32FractionPart2 = (int32_t) (fTemperature * 1000.0f);
SHT21_i32FractionPart2 = SHT21_i32FractionPart2 - (SHT21_i32IntegerPart2 * 1000);
if(SHT21_i32FractionPart2 < 0)
{
SHT21_i32FractionPart2 *= -1;
}
// //
// // Print the temperature as integer and fraction parts.
// //
// sprintf(tempString,"Temperature %3d.%03d\n\r", SHT21_i32IntegerPart2, SHT21_i32FractionPart2);
// CLI_Write(tempString);
}
else
{
SHT21DataRead(&g_sSHT21Inst, SHT21AppCallback, &g_sSHT21Inst);
SysCtlDelay(g_SysClock / (100 * 3));
//
// Get a copy of the most recent raw data in floating point format.
//
SHT21DataHumidityGetFloat(&g_sSHT21Inst, &fHumidity);
//
// Convert the floats to an integer part and fraction part for easy
// print. Humidity is returned as 0.0 to 1.0 so multiply by 100 to get
// percent humidity.
//
fHumidity *= 100.0f;
SHT21_i32IntegerPart1 = (int32_t) fHumidity;
SHT21_i32FractionPart1 = (int32_t) (fHumidity * 1000.0f);
SHT21_i32FractionPart1 = SHT21_i32FractionPart1 - (SHT21_i32IntegerPart1 * 1000);
if(SHT21_i32FractionPart1 < 0)
{
SHT21_i32FractionPart1 *= -1;
}
//
// //
// // Print the humidity value using the integers we just created.
// //
//sprintf(tempString,"Humidity %3d.%03d\n\r", SHT21_i32IntegerPart1, SHT21_i32FractionPart1);
//CLI_Write(tempString);
sensorTurn=(sensorTurn+1)%NumberOfSensor;
TimerEnable(TIMER1_BASE, TIMER_A);
flag=(flag+1)%3;
//
// Write the command to start a temperature measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_T, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
}
}
}
void printHumidityData(void){
float fTemperature, fHumidity;
int32_t i32IntegerPart;
int32_t i32FractionPart;
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Write the command to start a humidity measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_RH, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Wait 33 milliseconds before attempting to get the result. Datasheet
// claims this can take as long as 29 milliseconds.
//
ROM_SysCtlDelay(g_ui32SysClock / (30 * 3));
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Get the raw data from the sensor over the I2C bus.
//
SHT21DataRead(&g_sSHT21Inst, SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Get a copy of the most recent raw data in floating point format.
//
SHT21DataHumidityGetFloat(&g_sSHT21Inst, &fHumidity);
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Write the command to start a temperature measurement.
//
SHT21Write(&g_sSHT21Inst, SHT21_CMD_MEAS_T, g_sSHT21Inst.pui8Data, 0,
SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Wait 100 milliseconds before attempting to get the result. Datasheet
// claims this can take as long as 85 milliseconds.
//
ROM_SysCtlDelay(g_ui32SysClock / (10 * 3));
//
// Turn on D2 to show we are starting a transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Read the conversion data from the sensor over I2C.
//
SHT21DataRead(&g_sSHT21Inst, SHT21AppCallback, &g_sSHT21Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Get the most recent temperature result as a float in celcius.
//
SHT21DataTemperatureGetFloat(&g_sSHT21Inst, &fTemperature);
//
// Convert the floats to an integer part and fraction part for easy
// print. Humidity is returned as 0.0 to 1.0 so multiply by 100 to get
// percent humidity.
//
fHumidity *= 100.0f;
i32IntegerPart = (int32_t) fHumidity;
i32FractionPart = (int32_t) (fHumidity * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the humidity value using the integers we just created.
//
UARTprintf("Humidity %3d.%03d\t", i32IntegerPart, i32FractionPart);
//
// Perform the conversion from float to a printable set of integers.
//
i32IntegerPart = (int32_t) fTemperature;
i32FractionPart = (int32_t) (fTemperature * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the temperature as integer and fraction parts.
//
UARTprintf("Temperature %3d.%03d\n", i32IntegerPart, i32FractionPart);
//
// Delay for one second. This is to keep sensor duty cycle
// to about 10% as suggested in the datasheet, section 2.4.
// This minimizes self heating effects and keeps reading more accurate.
//
ROM_SysCtlDelay(g_ui32SysClock / 3);
}