EFI_STATUS
EFIAPI
UnlockFlashComponents (
IN EFI_SPI_PROTOCOL *This,
IN UINT8 UnlockCmdOpcodeIndex
)
/*++
Routine Description:
Issue unlock command to disable block protection, this only needs to be done once per SPI power on
Arguments:
This A pointer to "EFI_SPI_PROTOCOL" for issuing commands
UnlockCmdOpcodeIndex The index of the Unlock command
Returns:
EFI_SUCCESS UnLock operation succeed.
EFI_DEVICE_ERROR Device error, operation failed.
--*/
{
EFI_STATUS Status;
SPI_INSTANCE *SpiInstance;
UINT8 SpiStatus;
if (UnlockCmdOpcodeIndex >= SPI_NUM_OPCODE) {
return EFI_UNSUPPORTED;
}
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
//
// Issue unlock command to disable block protection, this only needs to be done once per SPI power on
//
SpiStatus = 0;
//
// Issue unlock command to the flash component 1 at first
//
Status = SpiProtocolExecute (
This,
UnlockCmdOpcodeIndex,
SpiInstance->SpiInitTable.PrefixOpcode[0] == PCH_SPI_COMMAND_WRITE_ENABLE ? 0 : 1,
TRUE,
TRUE,
TRUE,
(UINTN) 0,
sizeof (SpiStatus),
&SpiStatus,
EnumSpiRegionAll
);
if (EFI_ERROR (Status)) {
DEBUG ((EFI_D_ERROR, "Unlock flash component 1 fail!\n"));
return Status;
}
return EFI_SUCCESS;
}
BOOLEAN
WaitForSpiCycleComplete (
IN EFI_SPI_PROTOCOL *This,
IN BOOLEAN ErrorCheck
)
/*++
Routine Description:
Wait execution cycle to complete on the SPI interface. Check both Hardware
and Software Sequencing status registers
Arguments:
This - The SPI protocol instance
UseSoftwareSequence - TRUE if this is a Hardware Sequencing operation
ErrorCheck - TRUE if the SpiCycle needs to do the error check
Returns:
TRUE SPI cycle completed on the interface.
FALSE Time out while waiting the SPI cycle to complete.
It's not safe to program the next command on the SPI interface.
--*/
{
UINT64 WaitTicks;
UINT64 WaitCount;
UINT16 Data16;
SPI_INSTANCE *SpiInstance;
UINTN PchRootComplexBar;
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
PchRootComplexBar = SpiInstance->PchRootComplexBar;
//
// Convert the wait period allowed into to tick count
//
WaitCount = WAIT_TIME / WAIT_PERIOD;
//
// Wait for the SPI cycle to complete.
//
for (WaitTicks = 0; WaitTicks < WaitCount; WaitTicks++) {
Data16 = MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIS);
if ((Data16 & B_QNC_RCRB_SPIS_SCIP) == 0) {
MmioWrite16 (PchRootComplexBar + R_QNC_RCRB_SPIS, (B_QNC_RCRB_SPIS_BAS | B_QNC_RCRB_SPIS_CDS));
if ((Data16 & B_QNC_RCRB_SPIS_BAS) && (ErrorCheck == TRUE)) {
return FALSE;
} else {
return TRUE;
}
}
MicroSecondDelay (WAIT_PERIOD);
}
return FALSE;
}
VOID
SpiOffset2Physical (
IN EFI_SPI_PROTOCOL *This,
IN UINTN SpiRegionOffset,
IN SPI_REGION_TYPE SpiRegionType,
OUT UINTN *HardwareSpiAddress,
OUT UINTN *BaseAddress,
OUT UINTN *LimitAddress
)
/*++
Routine Description:
Convert SPI offset to Physical address of SPI hardware
Arguments:
This Pointer to the EFI_SPI_PROTOCOL instance.
SpiRegionOffset In Descriptor Mode, for Descriptor Region, GbE Region, ME Region and Platform
Region, this value specifies the offset from the Region Base; for BIOS Region,
this value specifies the offset from the start of the BIOS Image. In Non
Descriptor Mode, this value specifies the offset from the start of the BIOS Image.
Please note BIOS Image size may be smaller than BIOS Region size (in Descriptor
Mode) or the flash size (in Non Descriptor Mode), and in this case, BIOS Image is
supposed to be placed at the top end of the BIOS Region (in Descriptor Mode) or
the flash (in Non Descriptor Mode)
BaseAddress Base Address of the region.
SpiRegionType SPI Region type. Values EnumSpiRegionBios, EnumSpiRegionGbE, EnumSpiRegionMe,
EnumSpiRegionDescriptor, and EnumSpiRegionPlatformData are only applicable in
Descriptor mode. Value EnumSpiRegionAll is applicable to both Descriptor Mode
and Non Descriptor Mode, which indicates "SpiRegionOffset" is actually relative
to base of the 1st flash device (i.e., it is a Flash Linear Address).
HardwareSpiAddress Return absolution SPI address (i.e., Flash Linear Address)
BaseAddress Return base address of the region type
LimitAddress Return limit address of the region type
Returns:
EFI_SUCCESS Command succeed.
--*/
{
SPI_INSTANCE *SpiInstance;
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
if (SpiRegionType == EnumSpiRegionAll) {
//
// EnumSpiRegionAll indicates address is relative to flash device (i.e., address is Flash
// Linear Address)
//
*HardwareSpiAddress = SpiRegionOffset;
} else {
//
// Otherwise address is relative to BIOS image
//
*HardwareSpiAddress = SpiRegionOffset + SpiInstance->SpiInitTable.BiosStartOffset;
}
}
EFI_STATUS
EFIAPI
SpiProtocolInfo (
IN EFI_SPI_PROTOCOL *This,
OUT SPI_INIT_INFO **InitInfoPtr
)
/*++
Routine Description:
Return info about SPI host controller, to help callers usage of Execute
service.
If 0xff is returned as an opcode index in init info struct
then device does not support the operation.
Arguments:
This Pointer to the EFI_SPI_PROTOCOL instance.
InitInfoPtr Pointer to init info written to this memory location.
Returns:
EFI_SUCCESS Information returned.
EFI_INVALID_PARAMETER Invalid parameter.
EFI_NOT_READY Required resources not setup.
Others Unexpected error happened.
--*/
{
SPI_INSTANCE *SpiInstance;
if (This == NULL || InitInfoPtr == NULL) {
return EFI_INVALID_PARAMETER;
}
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
if (SpiInstance->Signature != PCH_SPI_PRIVATE_DATA_SIGNATURE) {
return EFI_INVALID_PARAMETER;
}
if (!SpiInstance->InitDone) {
*InitInfoPtr = NULL;
return EFI_NOT_READY;
}
*InitInfoPtr = &SpiInstance->InitInfo;
return EFI_SUCCESS;
}
EFI_STATUS
SendSpiCmd (
IN EFI_SPI_PROTOCOL *This,
IN UINT8 OpcodeIndex,
IN UINT8 PrefixOpcodeIndex,
IN BOOLEAN DataCycle,
IN BOOLEAN Atomic,
IN BOOLEAN ShiftOut,
IN UINTN Address,
IN UINT32 DataByteCount,
IN OUT UINT8 *Buffer,
IN SPI_REGION_TYPE SpiRegionType
)
/*++
Routine Description:
This function sends the programmed SPI command to the slave device.
Arguments:
OpcodeIndex Index of the command in the OpCode Menu.
PrefixOpcodeIndex Index of the first command to run when in an atomic cycle sequence.
DataCycle TRUE if the SPI cycle contains data
Atomic TRUE if the SPI cycle is atomic and interleave cycles are not allowed.
ShiftOut If DataByteCount is not zero, TRUE to shift data out and FALSE to shift data in.
Address In Descriptor Mode, for Descriptor Region, GbE Region, ME Region and Platform
Region, this value specifies the offset from the Region Base; for BIOS Region,
this value specifies the offset from the start of the BIOS Image. In Non
Descriptor Mode, this value specifies the offset from the start of the BIOS Image.
Please note BIOS Image size may be smaller than BIOS Region size (in Descriptor
Mode) or the flash size (in Non Descriptor Mode), and in this case, BIOS Image is
supposed to be placed at the top end of the BIOS Region (in Descriptor Mode) or
the flash (in Non Descriptor Mode)
DataByteCount Number of bytes in the data portion of the SPI cycle. This function may break the
data transfer into multiple operations. This function ensures each operation does
not cross 256 byte flash address boundary.
*NOTE: if there is some SPI chip that has a stricter address boundary requirement
(e.g., its write page size is < 256 byte), then the caller cannot rely on this
function to cut the data transfer at proper address boundaries, and it's the
caller's reponsibility to pass in a properly cut DataByteCount parameter.
Buffer Data received or sent during the SPI cycle.
SpiRegionType SPI Region type. Values EnumSpiRegionBios, EnumSpiRegionGbE, EnumSpiRegionMe,
EnumSpiRegionDescriptor, and EnumSpiRegionPlatformData are only applicable in
Descriptor mode. Value EnumSpiRegionAll is applicable to both Descriptor Mode
and Non Descriptor Mode, which indicates "SpiRegionOffset" is actually relative
to base of the 1st flash device (i.e., it is a Flash Linear Address).
Returns:
EFI_SUCCESS SPI command completes successfully.
EFI_DEVICE_ERROR Device error, the command aborts abnormally.
EFI_ACCESS_DENIED Some unrecognized command encountered in hardware sequencing mode
EFI_INVALID_PARAMETER The parameters specified are not valid.
--*/
{
UINT32 Index;
SPI_INSTANCE *SpiInstance;
UINTN HardwareSpiAddr;
UINTN SpiBiosSize;
UINTN BaseAddress;
UINTN LimitAddress;
UINT32 SpiDataCount;
UINT8 OpCode;
SPI_OPERATION Operation;
UINTN PchRootComplexBar;
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
PchRootComplexBar = SpiInstance->PchRootComplexBar;
SpiBiosSize = SpiInstance->SpiInitTable.BiosSize;
Operation = SpiInstance->SpiInitTable.OpcodeMenu[OpcodeIndex].Operation;
OpCode = MmioRead8 (PchRootComplexBar + R_QNC_RCRB_SPIOPMENU + OpcodeIndex);
//
// Check if the value of opcode register is 0 or the BIOS Size of SpiInitTable is 0
//
if (OpCode == 0 || SpiBiosSize == 0) {
ASSERT (FALSE);
return EFI_INVALID_PARAMETER;
}
SpiOffset2Physical (This, Address, SpiRegionType, &HardwareSpiAddr, &BaseAddress, &LimitAddress);
//
// Have direct access to BIOS region in Descriptor mode,
//
if (SpiInstance->SpiInitTable.OpcodeMenu[OpcodeIndex].Type == EnumSpiOpcodeRead &&
SpiRegionType == EnumSpiRegionBios) {
CopyMem (
Buffer,
(UINT8 *) ((HardwareSpiAddr - BaseAddress) + (UINT32) (~(SpiBiosSize - 1))),
DataByteCount
);
return EFI_SUCCESS;
}
//
// DEBUG((EFI_D_ERROR, "SPIADDR %x, %x, %x, %x\n", Address, HardwareSpiAddr, BaseAddress,
// LimitAddress));
//
if ((DataCycle == FALSE) && (DataByteCount > 0)) {
DataByteCount = 0;
}
do {
//
// Trim at 256 byte boundary per operation,
// - PCH SPI controller requires trimming at 4KB boundary
// - Some SPI chips require trimming at 256 byte boundary for write operation
// - Trimming has limited performance impact as we can read / write atmost 64 byte
// per operation
//
if (HardwareSpiAddr + DataByteCount > ((HardwareSpiAddr + BIT8) &~(BIT8 - 1))) {
SpiDataCount = (((UINT32) (HardwareSpiAddr) + BIT8) &~(BIT8 - 1)) - (UINT32) (HardwareSpiAddr);
} else {
SpiDataCount = DataByteCount;
}
//
// Calculate the number of bytes to shift in/out during the SPI data cycle.
// Valid settings for the number of bytes duing each data portion of the
// PCH SPI cycles are: 0, 1, 2, 3, 4, 5, 6, 7, 8, 16, 24, 32, 40, 48, 56, 64
//
if (SpiDataCount >= 64) {
SpiDataCount = 64;
} else if ((SpiDataCount &~0x07) != 0) {
SpiDataCount = SpiDataCount &~0x07;
}
//
// If shifts data out, load data into the SPI data buffer.
//
if (ShiftOut) {
for (Index = 0; Index < SpiDataCount; Index++) {
MmioWrite8 (PchRootComplexBar + R_QNC_RCRB_SPID0 + Index, Buffer[Index]);
MmioRead8 (PchRootComplexBar + R_QNC_RCRB_SPID0 + Index);
}
}
MmioWrite32 (
(PchRootComplexBar + R_QNC_RCRB_SPIA),
(UINT32) (HardwareSpiAddr & B_QNC_RCRB_SPIA_MASK)
);
MmioRead32 (PchRootComplexBar + R_QNC_RCRB_SPIA);
//
// Execute the command on the SPI compatible mode
//
//
// Clear error flags
//
MmioOr16 ((PchRootComplexBar + R_QNC_RCRB_SPIS), B_QNC_RCRB_SPIS_BAS);
//
// Initialte the SPI cycle
//
if (DataCycle) {
MmioWrite16 (
(PchRootComplexBar + R_QNC_RCRB_SPIC),
( (UINT16) (B_QNC_RCRB_SPIC_DC) | (UINT16) (((SpiDataCount - 1) << 8) & B_QNC_RCRB_SPIC_DBC) |
(UINT16) ((OpcodeIndex << 4) & B_QNC_RCRB_SPIC_COP) |
(UINT16) ((PrefixOpcodeIndex << 3) & B_QNC_RCRB_SPIC_SPOP) |
(UINT16) (Atomic ? B_QNC_RCRB_SPIC_ACS : 0) |
(UINT16) (B_QNC_RCRB_SPIC_SCGO)));
} else {
MmioWrite16 (
(PchRootComplexBar + R_QNC_RCRB_SPIC),
( (UINT16) ((OpcodeIndex << 4) & B_QNC_RCRB_SPIC_COP) |
(UINT16) ((PrefixOpcodeIndex << 3) & B_QNC_RCRB_SPIC_SPOP) |
(UINT16) (Atomic ? B_QNC_RCRB_SPIC_ACS : 0) |
(UINT16) (B_QNC_RCRB_SPIC_SCGO)));
}
MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIC);
//
// end of command execution
//
// Wait the SPI cycle to complete.
//
if (!WaitForSpiCycleComplete (This, TRUE)) {
return EFI_DEVICE_ERROR;
}
//
// If shifts data in, get data from the SPI data buffer.
//
if (!ShiftOut) {
for (Index = 0; Index < SpiDataCount; Index++) {
Buffer[Index] = MmioRead8 (PchRootComplexBar + R_QNC_RCRB_SPID0 + Index);
}
}
HardwareSpiAddr += SpiDataCount;
Buffer += SpiDataCount;
DataByteCount -= SpiDataCount;
} while (DataByteCount > 0);
return EFI_SUCCESS;
}
EFI_STATUS
EFIAPI
SpiProtocolLock (
IN EFI_SPI_PROTOCOL *This
)
/*++
Routine Description:
Lock the SPI Static Configuration Interface.
Once locked, the interface can not be changed and can only be clear by system reset.
Arguments:
This Pointer to the EFI_SPI_PROTOCOL instance.
Returns:
EFI_SUCCESS Lock operation succeed.
EFI_DEVICE_ERROR Device error, operation failed.
EFI_ACCESS_DENIED The interface has already been locked.
--*/
{
SPI_INSTANCE *SpiInstance;
UINTN PchRootComplexBar;
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
PchRootComplexBar = SpiInstance->PchRootComplexBar;
//
// Check if the SPI interface has been locked-down.
//
if ((MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIS) & B_QNC_RCRB_SPIS_SCL) != 0) {
return EFI_ACCESS_DENIED;
}
//
// Lock-down the configuration interface.
//
MmioOr16 ((UINTN) (PchRootComplexBar + R_QNC_RCRB_SPIS), (UINT16) (B_QNC_RCRB_SPIS_SCL));
//
// Verify if it's really locked.
//
if ((MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIS) & B_QNC_RCRB_SPIS_SCL) == 0) {
return EFI_DEVICE_ERROR;
} else {
//
// Save updated register in S3 Boot script.
//
S3BootScriptSaveMemWrite (
S3BootScriptWidthUint16,
(UINTN) (PchRootComplexBar + R_QNC_RCRB_SPIS),
1,
(VOID *) (UINTN) (PchRootComplexBar + R_QNC_RCRB_SPIS)
);
}
return EFI_SUCCESS;
}
EFI_STATUS
EFIAPI
SpiProtocolInit (
IN EFI_SPI_PROTOCOL *This,
IN SPI_INIT_TABLE *InitTable
)
/*++
Routine Description:
Initialize the host controller to execute SPI command.
Arguments:
This Pointer to the EFI_SPI_PROTOCOL instance.
InitTable Initialization data to be programmed into the SPI host controller.
Returns:
EFI_SUCCESS Initialization completed.
EFI_ACCESS_DENIED The SPI static configuration interface has been locked-down.
EFI_INVALID_PARAMETER Bad input parameters.
EFI_UNSUPPORTED Can't get Descriptor mode VSCC values
--*/
{
EFI_STATUS Status;
UINT8 Index;
UINT16 OpcodeType;
SPI_INSTANCE *SpiInstance;
BOOLEAN MultiPartitionIsSupported;
UINTN PchRootComplexBar;
UINT8 SFDPCmdOpcodeIndex;
UINT8 UnlockCmdOpcodeIndex;
UINT8 ReadDataCmdOpcodeIndex;
UINT8 FlashPartId[3];
SpiInstance = SPI_INSTANCE_FROM_SPIPROTOCOL (This);
PchRootComplexBar = SpiInstance->PchRootComplexBar;
if (InitTable != NULL) {
//
// Copy table into SPI driver Private data structure
//
CopyMem (
&SpiInstance->SpiInitTable,
InitTable,
sizeof (SPI_INIT_TABLE)
);
} else {
return EFI_INVALID_PARAMETER;
}
//
// Check if the SPI interface has been locked-down.
//
if ((MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIS) & B_QNC_RCRB_SPIS_SCL) != 0) {
ASSERT_EFI_ERROR (EFI_ACCESS_DENIED);
return EFI_ACCESS_DENIED;
}
//
// Clear all the status bits for status regs.
//
MmioOr16 (
(UINTN) (PchRootComplexBar + R_QNC_RCRB_SPIS),
(UINT16) ((B_QNC_RCRB_SPIS_CDS | B_QNC_RCRB_SPIS_BAS))
);
MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIS);
//
// Set the Prefix Opcode registers.
//
MmioWrite16 (
PchRootComplexBar + R_QNC_RCRB_SPIPREOP,
(SpiInstance->SpiInitTable.PrefixOpcode[1] << 8) | InitTable->PrefixOpcode[0]
);
MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIPREOP);
//
// Set Opcode Type Configuration registers.
//
for (Index = 0, OpcodeType = 0; Index < SPI_NUM_OPCODE; Index++) {
switch (SpiInstance->SpiInitTable.OpcodeMenu[Index].Type) {
case EnumSpiOpcodeRead:
OpcodeType |= (UINT16) (B_QNC_RCRB_SPIOPTYPE_ADD_READ << (Index * 2));
break;
case EnumSpiOpcodeWrite:
OpcodeType |= (UINT16) (B_QNC_RCRB_SPIOPTYPE_ADD_WRITE << (Index * 2));
break;
case EnumSpiOpcodeWriteNoAddr:
OpcodeType |= (UINT16) (B_QNC_RCRB_SPIOPTYPE_NOADD_WRITE << (Index * 2));
break;
default:
OpcodeType |= (UINT16) (B_QNC_RCRB_SPIOPTYPE_NOADD_READ << (Index * 2));
break;
}
}
MmioWrite16 (PchRootComplexBar + R_QNC_RCRB_SPIOPTYPE, OpcodeType);
MmioRead16 (PchRootComplexBar + R_QNC_RCRB_SPIOPTYPE);
//
// Setup the Opcode Menu registers.
//
ReadDataCmdOpcodeIndex = SPI_NUM_OPCODE;
SFDPCmdOpcodeIndex = SPI_NUM_OPCODE;
UnlockCmdOpcodeIndex = SPI_NUM_OPCODE;
for (Index = 0; Index < SPI_NUM_OPCODE; Index++) {
MmioWrite8 (
PchRootComplexBar + R_QNC_RCRB_SPIOPMENU + Index,
SpiInstance->SpiInitTable.OpcodeMenu[Index].Code
);
MmioRead8 (PchRootComplexBar + R_QNC_RCRB_SPIOPMENU + Index);
if (SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationJedecId) {
Status = SpiProtocolExecute (
This,
Index,
0,
TRUE,
TRUE,
FALSE,
(UINTN) 0,
3,
FlashPartId,
EnumSpiRegionDescriptor
);
if (EFI_ERROR (Status)) {
return Status;
}
if (FlashPartId[0] != SpiInstance->SpiInitTable.VendorId ||
FlashPartId[1] != SpiInstance->SpiInitTable.DeviceId0 ||
FlashPartId[2] != SpiInstance->SpiInitTable.DeviceId1) {
return EFI_INVALID_PARAMETER;
}
}
if (SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationReadData ||
SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationFastRead ||
SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationDualOutputFastRead) {
ReadDataCmdOpcodeIndex = Index;
}
if (SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationDiscoveryParameters) {
SFDPCmdOpcodeIndex = Index;
}
if (SpiInstance->SpiInitTable.OpcodeMenu[Index].Operation == EnumSpiOperationWriteStatus) {
UnlockCmdOpcodeIndex = Index;
}
}
MultiPartitionIsSupported = FALSE;
Status = UnlockFlashComponents (
This,
UnlockCmdOpcodeIndex
);
if (EFI_ERROR (Status)) {
DEBUG ((EFI_D_ERROR, "Unlock flash components fail!\n"));
}
SpiPhaseInit ();
FillOutPublicInfoStruct (SpiInstance);
SpiInstance->InitDone = TRUE;
return EFI_SUCCESS;
}
