/******************************************************************************
*
*
* This function erases the sectors in the serial FLASH connected to the SPI
* interface.
*
* @param InstancePtr is a pointer to the XIsf component to use.
* @param Address contains the address of the first sector which needs to
* be erased.
* @param ByteCount contains the total size to be erased.
*
* @return None.
*
* @note None.
*
******************************************************************************/
int FlashErase(XIsf *InstancePtr, u32 Address, u32 ByteCount)
{
int Status;
int Sector;
/*
* If the erase size is less than the total size of the flash, use
* sector erase command
*/
for (Sector = 0; Sector < ((ByteCount / SECTOR_SIZE) + 1); Sector++) {
/*
* Write enable instruction has to be executed prior to
* any Write operation.
*/
WriteEnable(InstancePtr);
/*
* Perform the Sector Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(InstancePtr, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
Address += SECTOR_SIZE;
}
return XST_SUCCESS;
}
/**
*
* Main function to execute the Numonyx Quad Serial Flash Read/Write example.
*
* @param None
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None
*
******************************************************************************/
int main()
{
int Status;
u32 Index;
u32 Address;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
XSpi_Start(&Spi);
/*
* Set the QSPI options
*/
Status = XIsf_SetSpiConfiguration(&Isf, &Spi,
XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION,
XISF_SPI_PRESCALER);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Initialize the Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = ISF_TEST_ADDRESS;
/*
* The following code Erases a Sector in the Numonyx Serial Flash.
*/
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_DUAL_IP_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Dual Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = DUAL_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_DUAL_OP_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_DUAL_IP_EXT_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Dual Input/Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = DUAL_IO_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_IO_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_DUAL_IO_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
DUAL_IO_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_QUAD_IP_PAGE_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Quad Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = QUAD_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_QUAD_OP_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Move to the next page in the flash.
*/
Address += ISF_PAGE_SIZE;
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - Number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_QUAD_IP_EXT_PAGE_WRITE,
(void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read from the flash using Quad Input/Output Fast Read command.
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
* - Number of dummy bytes for the read command.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
ReadParam.NumDummyBytes = QUAD_IO_READ_DUMMY_BYTES;
/*
* Clear the read Buffer.
*/
for(Index = 0; Index < ISF_PAGE_SIZE + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_IO_READ_DUMMY_BYTES; Index++) {
ReadBuffer[Index] = 0x0;
}
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_QUAD_IO_FAST_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES +
QUAD_IO_READ_DUMMY_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* Main function to execute the Atmel Serial Flash Read/Write example.
*
* @param None.
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None.
*
******************************************************************************/
int main(void)
{
int Status;
u16 Index;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
u32 Address;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
Status = XSpi_Start(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Initialize the In-system and Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = TEST_ADDRESS;
/*
* Perform the Page Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_PAGE_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Serial Flash is ready.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address within the Serial Flash where the data is to be written.
* - The number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Serial Flash is ready.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
/*
* Perform the Read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check for any errors.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the Data Read with the Data Written to the Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadParam.ReadPtr[Index + XISF_CMD_SEND_EXTRA_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* Main function to execute the Intel Serial Flash SPR example.
*
* @param None
*
* @return XST_SUCCESS if successful else XST_FAILURE.
*
* @note None
*
******************************************************************************/
int main()
{
int Status;
u32 Index;
u32 Address;
u8 StatusReg;
XIsf_WriteParam WriteParam;
XIsf_ReadParam ReadParam;
/*
* Initialize the SPI driver so that it's ready to use,
* specify the device ID that is generated in xparameters.h.
*/
Status = XSpi_Initialize(&Spi, SPI_DEVICE_ID);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Connect the SPI driver to the interrupt subsystem such that
* interrupts can occur. This function is application specific.
*/
Status = SetupInterruptSystem(&Spi);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Setup the handler for the SPI that will be called from the interrupt
* context when an SPI status occurs, specify a pointer to the SPI
* driver instance as the callback reference so the handler is able to
* access the instance data.
*/
XIsf_SetStatusHandler(&Isf, &Spi, (XSpi_StatusHandler)SpiHandler);
/*
* Start the SPI driver so that interrupts and the device are enabled.
*/
XSpi_Start(&Spi);
/*
* Initialize the Serial Flash Library.
*/
Status = XIsf_Initialize(&Isf, &Spi, ISF_SPI_SELECT, IsfWriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Set The transfer Mode to Interrupt
*/
XIsf_SetTransferMode(&Isf,XISF_INTERRUPT_MODE);
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Clear all the block protection bits in the sector protection register
* value read above.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] &
(~(XISF_SR_BLOCK_PROTECT_MASK));
/*
* Write this value to the sector protection register to disable the
* sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Specify the address in the Serial Flash for the Erase/Write/Read
* operations.
*/
Address = ISF_TEST_ADDRESS;
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* - Set the address within the Serial Flash where the data is to be
* written.
* - Set the number of bytes to be written to the Serial Flash.
* - Write Buffer which contains the data to be written to the Serial
* Flash.
*/
WriteParam.Address = Address;
WriteParam.NumBytes = ISF_PAGE_SIZE;
WriteParam.WritePtr = WriteBuffer;
/*
* Prepare the write buffer. Fill in the data need to be written into
* Serial Flash.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
WriteParam.WritePtr[Index] = Index + ISF_TEST_BYTE;
}
/*
* Perform the Write operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Write(&Isf, XISF_WRITE, (void*) &WriteParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Set all the block protection bits in the sector protection register
* value read above and write it back to the sector protection register.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] |
(XISF_SR_BLOCK_PROTECT_MASK);
/*
* Enable the sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Write Enable operation.
*/
TransferInProgress = TRUE;
Status = XIsf_WriteEnable(&Isf, XISF_WRITE_ENABLE);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Perform the Sector Erase operation. This should not work as writes to
* the Serial Flash are disabled.
*/
TransferInProgress = TRUE;
Status = XIsf_Erase(&Isf, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the Status Register.
*/
TransferInProgress = TRUE;
Status = XIsf_GetStatus(&Isf, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is in progress.
*/
while(TransferInProgress);
/*
* Check if there are any errors in the transaction.
*/
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Check if the erase fail flag is set in the status register. This flag
* should be set as a sector erase operation was attempted when sector
* protection was enabled.
*/
StatusReg = ReadBuffer[BYTE2];
if((StatusReg & XISF_SR_ERASE_FAIL_MASK) == 0) {
return XST_FAILURE;
}
/*
* Clear the status register fail flags in the Serial Flash status
* register.
*/
TransferInProgress = TRUE;
Status = XIsf_Ioctl(&Isf, XISF_IOCTL_CLEAR_SR_FAIL_FLAGS);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Read the Status Register.
*/
TransferInProgress = TRUE;
Status = XIsf_GetStatus(&Isf, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is in progress.
*/
while(TransferInProgress);
/*
* Check if there are any errors in the transaction.
*/
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Check if the erase fail flag is clear in the status register. This
* flag should be clear as a 'Clear SR Fail Flags' command has been
* executed.
*/
StatusReg = ReadBuffer[BYTE2];
if((StatusReg & XISF_SR_ERASE_FAIL_MASK) != 0) {
return XST_FAILURE;
}
/*
* Read the sector protection register.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_READ, ReadBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Clear all the block protection bits in the sector protection register
* value read above and write it back to the sector protection register
* to disable sector protection for all sectors.
*/
WriteBuffer[BYTE1] = ReadBuffer[BYTE2] &
~(XISF_SR_BLOCK_PROTECT_MASK);
/*
* Disable the sector protection.
*/
TransferInProgress = TRUE;
Status = XIsf_SectorProtect(&Isf, XISF_SPR_WRITE, WriteBuffer);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Wait till the Flash is not Busy.
*/
Status = IsfWaitForFlashNotBusy();
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* The following code Reads data from a Page in the Intel Serial Flash.
*/
/*
* Set the
* - Address in the Serial Flash where the data is to be read from.
* - Number of bytes to be read from the Serial Flash.
* - Read Buffer to which the data is to be read.
*/
ReadParam.Address = Address;
ReadParam.NumBytes = ISF_PAGE_SIZE;
ReadParam.ReadPtr = ReadBuffer;
/*
* Perform the read operation.
*/
TransferInProgress = TRUE;
Status = XIsf_Read(&Isf, XISF_READ, (void*) &ReadParam);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
/*
* Wait till the Transfer is complete and check if there are any errors
* in the transaction.
*/
while(TransferInProgress);
if(ErrorCount != 0) {
return XST_FAILURE;
}
/*
* Compare the data read against the data Written.
*/
for(Index = 0; Index < ISF_PAGE_SIZE; Index++) {
if(ReadBuffer[Index + XISF_CMD_SEND_EXTRA_BYTES] !=
(u8)(Index + ISF_TEST_BYTE)) {
return XST_FAILURE;
}
}
return XST_SUCCESS;
}
/**
*
* This function erases the sectors in the serial FLASH connected to the
* QSPI interface.
*
* @param InstancePtr is a pointer to the XIsf component to use.
* @param Address contains the address of the first sector which needs to
* be erased.
* @param ByteCount contains the total size to be erased.
*
* @return None.
*
* @note None.
*
******************************************************************************/
int FlashErase(XIsf *InstancePtr, u32 Address, u32 ByteCount)
{
int Status;
int Sector;
u32 LqspiCr;
u32 NumSect;
u32 SectorSize;
u32 NumSectors;
u32 Sector_Mask;
/*
* Get the value of Sector Size and Number of Sectors for the flash
*/
SectorSize = Isf.SectorSize;
NumSectors = Isf.NumSectors;
/* Get the sector mask value */
Sector_Mask = SectorMask(SectorSize);
/*
* If erase size is same as the total size of the flash, use bulk erase
* command
*/
if (ByteCount == (NumSectors * SectorSize)) {
#ifdef XPAR_XQSPIPS_0_DEVICE_ID
if(ConfigPtr->ConnectionMode ==
XQSPIPS_CONNECTION_MODE_STACKED){
/*
* Get the current LQSPI configuration register value
*/
LqspiCr =
XQspiPs_GetLqspiConfigReg(InstancePtr->SpiInstPtr);
/*
* Set selection to L_PAGE
*/
XQspiPs_SetLqspiConfigReg(InstancePtr->SpiInstPtr,
LqspiCr & (~XQSPIPS_LQSPI_CR_U_PAGE_MASK));
/*
* Assert the Flash chip select.
*/
XQspiPs_SetSlaveSelect(InstancePtr->SpiInstPtr);
}
#endif /*XPAR_XQSPIPS_0_DEVICE_ID*/
/*
* Call Bulk erase
*/
Status = XIsf_Erase(InstancePtr,
XISF_BULK_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
#ifdef XPAR_XQSPIPS_0_DEVICE_ID
/*
* If stacked mode, bulk erase second flash
*/
if(ConfigPtr->ConnectionMode ==
XQSPIPS_CONNECTION_MODE_STACKED){
/*
* Get the current LQSPI configuration register value
*/
LqspiCr =
XQspiPs_GetLqspiConfigReg(InstancePtr->SpiInstPtr);
/*
* Set selection to U_PAGE
*/
XQspiPs_SetLqspiConfigReg(InstancePtr->SpiInstPtr,
LqspiCr | XQSPIPS_LQSPI_CR_U_PAGE_MASK);
/*
* Assert the Flash chip select.
*/
XQspiPs_SetSlaveSelect(InstancePtr->SpiInstPtr);
/*
* Call Bulk erase
*/
Status = XIsf_Erase(InstancePtr,
XISF_BULK_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
}
#endif /*XPAR_XQSPIPS_0_DEVICE_ID*/
return Status;
}
/*
* Calculate no. of sectors to erase based on byte count
*/
NumSect = ByteCount/SectorSize + 1;
/*
* If ByteCount to k sectors,
* but the address range spans from N to N+k+1 sectors, then
* increment no. of sectors to be erased
*/
if( ((Address + ByteCount) & Sector_Mask) ==
((Address + (NumSect * SectorSize)) &
Sector_Mask) ) {
NumSect++;
}
/*
* If the erase size is less than the total size of the flash, use
* sector erase command
*/
for (Sector = 0; Sector < NumSect; Sector++) {
/*
* Perform the Sector Erase operation.
*/
Status = XIsf_Erase(InstancePtr, XISF_SECTOR_ERASE, Address);
if(Status != XST_SUCCESS) {
return XST_FAILURE;
}
Address += SectorSize;
}
return XST_SUCCESS;
}