int nsh_archinitialize(void)
{
int result;
/* INIT 1 Lowest level NuttX initialization has been done at this point, LEDs and UARTs are configured */
/* INIT 2 Configuring PX4 low-level peripherals, these will be always needed */
/* configure the high-resolution time/callout interface */
#ifdef CONFIG_HRT_TIMER
hrt_init();
#endif
/* configure CPU load estimation */
#ifdef CONFIG_SCHED_INSTRUMENTATION
cpuload_initialize_once();
#endif
/* set up the serial DMA polling */
#ifdef SERIAL_HAVE_DMA
{
static struct hrt_call serial_dma_call;
struct timespec ts;
/*
* Poll at 1ms intervals for received bytes that have not triggered
* a DMA event.
*/
ts.tv_sec = 0;
ts.tv_nsec = 1000000;
hrt_call_every(&serial_dma_call,
ts_to_abstime(&ts),
ts_to_abstime(&ts),
(hrt_callout)stm32_serial_dma_poll,
NULL);
}
#endif
message("\r\n");
up_ledoff(LED_BLUE);
up_ledoff(LED_AMBER);
up_ledon(LED_BLUE);
/* Configure user-space led driver */
px4fmu_led_init();
/* Configure SPI-based devices */
spi1 = up_spiinitialize(1);
if (!spi1)
{
message("[boot] FAILED to initialize SPI port 1\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
// Setup 10 MHz clock (maximum rate the BMA180 can sustain)
SPI_SETFREQUENCY(spi1, 10000000);
SPI_SETBITS(spi1, 8);
SPI_SETMODE(spi1, SPIDEV_MODE3);
SPI_SELECT(spi1, PX4_SPIDEV_GYRO, false);
SPI_SELECT(spi1, PX4_SPIDEV_ACCEL, false);
SPI_SELECT(spi1, PX4_SPIDEV_MPU, false);
up_udelay(20);
message("[boot] Successfully initialized SPI port 1\r\n");
/* initialize SPI peripherals redundantly */
int gyro_attempts = 0;
int gyro_fail = 0;
while (gyro_attempts < 5)
{
gyro_fail = l3gd20_attach(spi1, PX4_SPIDEV_GYRO);
gyro_attempts++;
if (gyro_fail == 0) break;
up_udelay(1000);
}
if (gyro_fail) message("[boot] FAILED to attach L3GD20 gyro\r\n");
int acc_attempts = 0;
int acc_fail = 0;
while (acc_attempts < 5)
{
acc_fail = bma180_attach(spi1, PX4_SPIDEV_ACCEL);
acc_attempts++;
if (acc_fail == 0) break;
up_udelay(1000);
}
if (acc_fail) message("[boot] FAILED to attach BMA180 accelerometer\r\n");
int mpu_attempts = 0;
int mpu_fail = 0;
while (mpu_attempts < 1)
{
mpu_fail = mpu6000_attach(spi1, PX4_SPIDEV_MPU);
mpu_attempts++;
if (mpu_fail == 0) break;
up_udelay(200);
}
if (mpu_fail) message("[boot] FAILED to attach MPU 6000 gyro/acc\r\n");
/* initialize I2C2 bus */
i2c2 = up_i2cinitialize(2);
if (!i2c2) {
message("[boot] FAILED to initialize I2C bus 2\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C2 speed */
I2C_SETFREQUENCY(i2c2, 400000);
i2c3 = up_i2cinitialize(3);
if (!i2c3) {
message("[boot] FAILED to initialize I2C bus 3\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C3 speed */
I2C_SETFREQUENCY(i2c3, 400000);
int mag_attempts = 0;
int mag_fail = 0;
while (mag_attempts < 5)
{
mag_fail = hmc5883l_attach(i2c2);
mag_attempts++;
if (mag_fail == 0) break;
up_udelay(1000);
}
if (mag_fail) message("[boot] FAILED to attach HMC5883L magnetometer\r\n");
int baro_attempts = 0;
int baro_fail = 0;
while (baro_attempts < 5)
{
baro_fail = ms5611_attach(i2c2);
baro_attempts++;
if (baro_fail == 0) break;
up_udelay(1000);
}
if (baro_fail) message("[boot] FAILED to attach MS5611 baro at addr #1 or #2 (0x76 or 0x77)\r\n");
/* try to attach, don't fail if device is not responding */
(void)eeprom_attach(i2c3, FMU_BASEBOARD_EEPROM_ADDRESS,
FMU_BASEBOARD_EEPROM_TOTAL_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_WRITE_TIME_US, "/dev/baseboard_eeprom", 1);
int eeprom_attempts = 0;
int eeprom_fail;
while (eeprom_attempts < 5)
{
/* try to attach, fail if device does not respond */
eeprom_fail = eeprom_attach(i2c2, FMU_ONBOARD_EEPROM_ADDRESS,
FMU_ONBOARD_EEPROM_TOTAL_SIZE_BYTES,
FMU_ONBOARD_EEPROM_PAGE_SIZE_BYTES,
FMU_ONBOARD_EEPROM_PAGE_WRITE_TIME_US, "/dev/eeprom", 1);
eeprom_attempts++;
if (eeprom_fail == OK) break;
up_udelay(1000);
}
if (eeprom_fail) message("[boot] FAILED to attach FMU EEPROM\r\n");
/* Report back sensor status */
if (acc_fail || gyro_fail || mag_fail || baro_fail || eeprom_fail)
{
up_ledon(LED_AMBER);
}
#if defined(CONFIG_STM32_SPI3)
/* Get the SPI port */
message("[boot] Initializing SPI port 3\r\n");
spi3 = up_spiinitialize(3);
if (!spi3)
{
message("[boot] FAILED to initialize SPI port 3\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully initialized SPI port 3\r\n");
/* Now bind the SPI interface to the MMCSD driver */
result = mmcsd_spislotinitialize(CONFIG_NSH_MMCSDMINOR, CONFIG_NSH_MMCSDSLOTNO, spi3);
if (result != OK)
{
message("[boot] FAILED to bind SPI port 3 to the MMCSD driver\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully bound SPI port 3 to the MMCSD driver\r\n");
#endif /* SPI3 */
/* initialize I2C1 bus */
i2c1 = up_i2cinitialize(1);
if (!i2c1) {
message("[boot] FAILED to initialize I2C bus 1\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C1 speed */
I2C_SETFREQUENCY(i2c1, 400000);
/* INIT 3: MULTIPORT-DEPENDENT INITIALIZATION */
/* Get board information if available */
/* Initialize the user GPIOs */
px4fmu_gpio_init();
#ifdef CONFIG_ADC
int adc_state = adc_devinit();
if (adc_state != OK)
{
/* Try again */
adc_state = adc_devinit();
if (adc_state != OK)
{
/* Give up */
message("[boot] FAILED adc_devinit: %d\r\n", adc_state);
return -ENODEV;
}
}
#endif
/* configure the tone generator */
#ifdef CONFIG_TONE_ALARM
tone_alarm_init();
#endif
return OK;
}
int adc_main(int argc, char *argv[])
{
struct adc_msg_s sample[CONFIG_EXAMPLES_ADC_GROUPSIZE];
size_t readsize;
ssize_t nbytes;
int fd;
int errval = 0;
int ret;
int i;
/* Check if we have initialized */
if (!g_adcstate.initialized)
{
/* Initialization of the ADC hardware is performed by logic external to
* this test.
*/
message("adc_main: Initializing external ADC device\n");
ret = adc_devinit();
if (ret != OK)
{
message("adc_main: adc_devinit failed: %d\n", ret);
errval = 1;
goto errout;
}
/* Set the default values */
adc_devpath(&g_adcstate, CONFIG_EXAMPLES_ADC_DEVPATH);
#if CONFIG_EXAMPLES_ADC_NSAMPLES > 0
g_adcstate.count = CONFIG_EXAMPLES_ADC_NSAMPLES;
#else
g_adcstate.count = 1;
#endif
g_adcstate.initialized = true;
}
/* Parse the command line */
#ifdef CONFIG_NSH_BUILTIN_APPS
parse_args(&g_adcstate, argc, argv);
#endif
/* If this example is configured as an NX add-on, then limit the number of
* samples that we collect before returning. Otherwise, we never return
*/
#if defined(CONFIG_NSH_BUILTIN_APPS) || CONFIG_EXAMPLES_ADC_NSAMPLES > 0
message("adc_main: g_adcstate.count: %d\n", g_adcstate.count);
#endif
/* Open the ADC device for reading */
message("adc_main: Hardware initialized. Opening the ADC device: %s\n",
g_adcstate.devpath);
fd = open(g_adcstate.devpath, O_RDONLY);
if (fd < 0)
{
message("adc_main: open %s failed: %d\n", g_adcstate.devpath, errno);
errval = 2;
goto errout_with_dev;
}
/* Now loop the appropriate number of times, displaying the collected
* ADC samples.
*/
#if defined(CONFIG_NSH_BUILTIN_APPS)
for (; g_adcstate.count > 0; g_adcstate.count--)
#elif CONFIG_EXAMPLES_ADC_NSAMPLES > 0
for (g_adcstate.count = 0; g_adcstate.count < CONFIG_EXAMPLES_ADC_NSAMPLES; g_adcstate.count++)
#else
for (;;)
#endif
{
/* Flush any output before the loop entered or from the previous pass
* through the loop.
*/
msgflush();
/* Read CONFIG_EXAMPLES_ADC_GROUPSIZE samples */
readsize = CONFIG_EXAMPLES_ADC_GROUPSIZE * sizeof(struct adc_msg_s);
nbytes = read(fd, sample, readsize);
/* Handle unexpected return values */
if (nbytes < 0)
{
errval = errno;
if (errval != EINTR)
{
message("adc_main: read %s failed: %d\n",
g_adcstate.devpath, errval);
errval = 3;
goto errout_with_dev;
}
message("adc_main: Interrupted read...\n");
}
else if (nbytes == 0)
{
message("adc_main: No data read, Ignoring\n");
}
/* Print the sample data on successful return */
else
{
int nsamples = nbytes / sizeof(struct adc_msg_s);
if (nsamples * sizeof(struct adc_msg_s) != nbytes)
{
message("adc_main: read size=%d is not a multiple of sample size=%d, Ignoring\n",
nbytes, sizeof(struct adc_msg_s));
}
else
{
message("Sample:\n");
for (i = 0; i < nsamples ; i++)
{
message("%d: channel: %d value: %d\n",
i, sample[i].am_channel, sample[i].am_data);
}
}
}
}
errout_with_dev:
close(fd);
errout:
message("Terminating!\n");
msgflush();
return errval;
}
int nsh_archinitialize(void)
{
int result;
/* INIT 1 Lowest level NuttX initialization has been done at this point, LEDs and UARTs are configured */
/* INIT 2 Configuring PX4 low-level peripherals, these will be always needed */
/* configure the high-resolution time/callout interface */
#ifdef CONFIG_HRT_TIMER
hrt_init();
#endif
/* configure CPU load estimation */
#ifdef CONFIG_SCHED_INSTRUMENTATION
cpuload_initialize_once();
#endif
/* set up the serial DMA polling */
#ifdef SERIAL_HAVE_DMA
{
static struct hrt_call serial_dma_call;
struct timespec ts;
/*
* Poll at 1ms intervals for received bytes that have not triggered
* a DMA event.
*/
ts.tv_sec = 0;
ts.tv_nsec = 1000000;
hrt_call_every(&serial_dma_call,
ts_to_abstime(&ts),
ts_to_abstime(&ts),
(hrt_callout)stm32_serial_dma_poll,
NULL);
}
#endif
message("\r\n");
up_ledoff(LED_BLUE);
up_ledoff(LED_AMBER);
up_ledon(LED_BLUE);
/* Configure user-space led driver */
px4fmu_led_init();
i2c2 = up_i2cinitialize(2);
if (!i2c2) {
message("[boot] FAILED to initialize I2C bus 3\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
/* set I2C3 speed */
I2C_SETFREQUENCY(i2c2, 400000);
/* try to attach, don't fail if device is not responding */
(void)eeprom_attach(i2c2, FMU_BASEBOARD_EEPROM_ADDRESS,
FMU_BASEBOARD_EEPROM_TOTAL_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_SIZE_BYTES,
FMU_BASEBOARD_EEPROM_PAGE_WRITE_TIME_US, "/dev/baseboard_eeprom", 1);
int eeprom_attempts = 0;
int eeprom_fail;
while (eeprom_attempts < 5)
{
/* try to attach, fail if device does not respond */
eeprom_fail = eeprom_attach(i2c2, FMU_ONBOARD_EEPROM_ADDRESS,
FMU_ONBOARD_EEPROM_TOTAL_SIZE_BYTES,
FMU_ONBOARD_EEPROM_PAGE_SIZE_BYTES,
FMU_ONBOARD_EEPROM_PAGE_WRITE_TIME_US, "/dev/eeprom", 1);
eeprom_attempts++;
if (eeprom_fail == OK) break;
up_udelay(1000);
}
if (eeprom_fail) message("[boot] FAILED to attach FMU EEPROM\r\n");
/* Report back sensor status */
if (eeprom_fail)
{
up_ledon(LED_AMBER);
}
#if defined(CONFIG_STM32_SPI3)
/* Get the SPI port */
message("[boot] Initializing SPI port 3\r\n");
spi3 = up_spiinitialize(3);
if (!spi3)
{
message("[boot] FAILED to initialize SPI port 3\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully initialized SPI port 3\r\n");
/* Now bind the SPI interface to the MMCSD driver */
result = mmcsd_spislotinitialize(CONFIG_NSH_MMCSDMINOR, CONFIG_NSH_MMCSDSLOTNO, spi3);
if (result != OK)
{
message("[boot] FAILED to bind SPI port 3 to the MMCSD driver\r\n");
up_ledon(LED_AMBER);
return -ENODEV;
}
message("[boot] Successfully bound SPI port 3 to the MMCSD driver\r\n");
#endif /* SPI3 */
/* INIT 3: MULTIPORT-DEPENDENT INITIALIZATION */
/* Get board information if available */
/* Initialize the user GPIOs */
px4fmu_gpio_init();
#ifdef CONFIG_ADC
int adc_state = adc_devinit();
if (adc_state != OK)
{
/* Try again */
adc_state = adc_devinit();
if (adc_state != OK)
{
/* Give up */
message("[boot] FAILED adc_devinit: %d\r\n", adc_state);
return -ENODEV;
}
}
#endif
/* configure the tone generator */
#ifdef CONFIG_TONE_ALARM
tone_alarm_init();
#endif
return OK;
}
int MAIN_NAME(int argc, char *argv[])
{
struct adc_msg_s sample[CONFIG_EXAMPLES_ADC_GROUPSIZE];
size_t readsize;
ssize_t nbytes;
#if defined(CONFIG_NSH_BUILTIN_APPS) || defined(CONFIG_EXAMPLES_ADC_NSAMPLES)
long nloops;
#endif
int fd;
int errval = 0;
int ret;
int i;
/* If this example is configured as an NX add-on, then limit the number of
* samples that we collect before returning. Otherwise, we never return
*/
#if defined(CONFIG_NSH_BUILTIN_APPS)
nloops = 1;
if (argc > 1)
{
nloops = strtol(argv[1], NULL, 10);
}
message(MAIN_STRING "nloops: %d\n", nloops);
#elif defined(CONFIG_EXAMPLES_ADC_NSAMPLES)
message(MAIN_STRING "nloops: %d\n", CONFIG_EXAMPLES_ADC_NSAMPLES);
#endif
/* Initialization of the ADC hardware is performed by logic external to
* this test.
*/
message(MAIN_STRING "Initializing external ADC device\n");
ret = adc_devinit();
if (ret != OK)
{
message(MAIN_STRING "adc_devinit failed: %d\n", ret);
errval = 1;
goto errout;
}
/* Open the ADC device for reading */
message(MAIN_STRING "Hardware initialized. Opening the ADC device\n");
fd = open(CONFIG_EXAMPLES_ADC_DEVPATH, O_RDONLY);
if (fd < 0)
{
message(MAIN_STRING "open %s failed: %d\n",
CONFIG_EXAMPLES_ADC_DEVPATH, errno);
errval = 2;
goto errout_with_dev;
}
/* Now loop the appropriate number of times, displaying the collected
* ADC samples.
*/
#if defined(CONFIG_NSH_BUILTIN_APPS)
for (; nloops > 0; nloops--)
#elif defined(CONFIG_EXAMPLES_ADC_NSAMPLES)
for (nloops = 0; nloops < CONFIG_EXAMPLES_ADC_NSAMPLES; nloops++)
#else
for (;;)
#endif
{
/* Flush any output before the loop entered or from the previous pass
* through the loop.
*/
msgflush();
/* Read CONFIG_EXAMPLES_ADC_GROUPSIZE samples */
readsize = CONFIG_EXAMPLES_ADC_GROUPSIZE * sizeof(struct adc_msg_s);
nbytes = read(fd, sample, readsize);
/* Handle unexpected return values */
if (nbytes < 0)
{
errval = errno;
if (errval != EINTR)
{
message(MAIN_STRING "read %s failed: %d\n",
CONFIG_EXAMPLES_ADC_DEVPATH, errval);
errval = 3;
goto errout_with_dev;
}
message(MAIN_STRING "Interrupted read...\n");
}
else if (nbytes == 0)
{
message(MAIN_STRING "No data read, Ignoring\n");
}
/* Print the sample data on successful return */
else
{
int nsamples = nbytes / sizeof(struct adc_msg_s);
if (nsamples * sizeof(struct adc_msg_s) != nbytes)
{
message(MAIN_STRING "read size=%d is not a multiple of sample size=%d, Ignoring\n",
nbytes, sizeof(struct adc_msg_s));
}
else
{
message("Sample:\n");
for (i = 0; i < nsamples ; i++)
{
message("%d: channel: %d value: %d\n",
i, sample[i].am_channel, sample[i].am_data);
}
}
}
}
errout_with_dev:
close(fd);
errout:
message("Terminating!\n");
msgflush();
return errval;
}