static int __init add_legacy_soc_port(struct device_node *np,
struct device_node *soc_dev)
{
u64 addr;
const u32 *addrp;
upf_t flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
struct device_node *tsi = of_get_parent(np);
/* We only support ports that have a clock frequency properly
* encoded in the device-tree.
*/
if (get_property(np, "clock-frequency", NULL) == NULL)
return -1;
/* if rtas uses this device, don't try to use it as well */
if (get_property(np, "used-by-rtas", NULL) != NULL)
return -1;
/* Get the address */
addrp = of_get_address(soc_dev, 0, NULL, NULL);
if (addrp == NULL)
return -1;
addr = of_translate_address(soc_dev, addrp);
if (addr == OF_BAD_ADDR)
return -1;
/* Add port, irq will be dealt with later. We passed a translated
* IO port value. It will be fixed up later along with the irq
*/
if (tsi && !strcmp(tsi->type, "tsi-bridge"))
return add_legacy_port(np, -1, UPIO_TSI, addr, addr, NO_IRQ, flags, 0);
else
return add_legacy_port(np, -1, UPIO_MEM, addr, addr, NO_IRQ, flags, 0);
}
static int __init add_legacy_isa_port(struct device_node *np,
struct device_node *isa_brg)
{
const u32 *reg;
const char *typep;
int index = -1;
u64 taddr;
DBG(" -> add_legacy_isa_port(%s)\n", np->full_name);
/* Get the ISA port number */
reg = of_get_property(np, "reg", NULL);
if (reg == NULL)
return -1;
/* Verify it's an IO port, we don't support anything else */
if (!(reg[0] & 0x00000001))
return -1;
/* Now look for an "ibm,aix-loc" property that gives us ordering
* if any...
*/
typep = of_get_property(np, "ibm,aix-loc", NULL);
/* If we have a location index, then use it */
if (typep && *typep == 'S')
index = simple_strtol(typep+1, NULL, 0) - 1;
/* Translate ISA address. If it fails, we still register the port
* with no translated address so that it can be picked up as an IO
* port later by the serial driver
*/
taddr = of_translate_address(np, reg);
if (taddr == OF_BAD_ADDR)
taddr = 0;
/* Add port, irq will be dealt with later */
return add_legacy_port(np, index, UPIO_PORT, reg[1], taddr,
NO_IRQ, UPF_BOOT_AUTOCONF, 0);
}
static int __init add_legacy_pci_port(struct device_node *np,
struct device_node *pci_dev)
{
u64 addr, base;
const u32 *addrp;
unsigned int flags;
int iotype, index = -1, lindex = 0;
DBG(" -> add_legacy_pci_port(%s)\n", np->full_name);
/* We only support ports that have a clock frequency properly
* encoded in the device-tree (that is have an fcode). Anything
* else can't be used that early and will be normally probed by
* the generic 8250_pci driver later on. The reason is that 8250
* compatible UARTs on PCI need all sort of quirks (port offsets
* etc...) that this code doesn't know about
*/
if (of_get_property(np, "clock-frequency", NULL) == NULL)
return -1;
/* Get the PCI address. Assume BAR 0 */
addrp = of_get_pci_address(pci_dev, 0, NULL, &flags);
if (addrp == NULL)
return -1;
/* We only support BAR 0 for now */
iotype = (flags & IORESOURCE_MEM) ? UPIO_MEM : UPIO_PORT;
addr = of_translate_address(pci_dev, addrp);
if (addr == OF_BAD_ADDR)
return -1;
/* Set the IO base to the same as the translated address for MMIO,
* or to the domain local IO base for PIO (it will be fixed up later)
*/
if (iotype == UPIO_MEM)
base = addr;
else
base = addrp[2];
/* Try to guess an index... If we have subdevices of the pci dev,
* we get to their "reg" property
*/
if (np != pci_dev) {
const u32 *reg = of_get_property(np, "reg", NULL);
if (reg && (*reg < 4))
index = lindex = *reg;
}
/* Local index means it's the Nth port in the PCI chip. Unfortunately
* the offset to add here is device specific. We know about those
* EXAR ports and we default to the most common case. If your UART
* doesn't work for these settings, you'll have to add your own special
* cases here
*/
if (of_device_is_compatible(pci_dev, "pci13a8,152") ||
of_device_is_compatible(pci_dev, "pci13a8,154") ||
of_device_is_compatible(pci_dev, "pci13a8,158")) {
addr += 0x200 * lindex;
base += 0x200 * lindex;
} else {
addr += 8 * lindex;
base += 8 * lindex;
}
/* Add port, irq will be dealt with later. We passed a translated
* IO port value. It will be fixed up later along with the irq
*/
return add_legacy_port(np, index, iotype, base, addr, NO_IRQ,
UPF_BOOT_AUTOCONF, np != pci_dev);
}