bool at90can_init(uint8_t bitrate)
{
if (bitrate >= 8)
return false;
// switch CAN controller to reset mode
CANGCON |= (1 << SWRES);
// set CAN Bit Timing
// (see datasheet page 260)
CANBT1 = pgm_read_byte(&_at90can_cnf[bitrate][0]);
CANBT2 = pgm_read_byte(&_at90can_cnf[bitrate][1]);
CANBT3 = pgm_read_byte(&_at90can_cnf[bitrate][2]);
// activate CAN transmit- and receive-interrupt
CANGIT = 0;
CANGIE = (1 << ENIT) | (1 << ENRX) | (1 << ENTX);
// set timer prescaler to 199 which results in a timer
// frequency of 10 kHz (at 16 MHz)
CANTCON = 199;
// disable all filters
at90can_disable_filter( 0xff );
#if CAN_RX_BUFFER_SIZE > 0
can_buffer_init( &can_rx_buffer, CAN_RX_BUFFER_SIZE, can_rx_list );
#endif
#if CAN_TX_BUFFER_SIZE > 0
can_buffer_init( &can_tx_buffer, CAN_TX_BUFFER_SIZE, can_tx_list );
#endif
// activate CAN controller
CANGCON = (1 << ENASTB);
return true;
}
bool at90can_init(uint8_t bitrate)
{
if (bitrate >= 8)
return false;
// switch CAN controller to reset mode
CANGCON |= (1 << SWRES);
// set CAN Bit Timing
// (see datasheet page 260)
CANBT1 = pgm_read_byte(&_at90can_cnf[bitrate][0]);
CANBT2 = pgm_read_byte(&_at90can_cnf[bitrate][1]);
CANBT3 = pgm_read_byte(&_at90can_cnf[bitrate][2]);
// activate CAN transmit- and receive-interrupt
CANGIT = 0;
CANGIE = (1 << ENIT) | (1 << ENRX) | (1 << ENTX);
// set timer prescaler to 199 which results in a timer
// frequency of 10 kHz (at 16 MHz)
CANTCON = 199;
// disable all filters
at90can_disable_filter( 0xff );
#if CAN_RX_BUFFER_SIZE > 0
can_buffer_init( &can_rx_buffer, CAN_RX_BUFFER_SIZE, can_rx_list );
#endif
#if CAN_TX_BUFFER_SIZE > 0
can_buffer_init( &can_tx_buffer, CAN_TX_BUFFER_SIZE, can_tx_list );
#endif
//Clear all mailboxes. DEG 22 May 2011
uint8_t i;
for(i = 0; i < 15; ++i)
{
CANPAGE = (i << 4);
//clear any interrupt flags
CANSTMOB = 0;
//DEG 23 May 2011. Configure each mailbox.
// From Datasheet, 19.5.2:
// "There is no default mode after RESET.
// "Every MOb has its own fields to control the operating mode.
// "Before enabling the CAN peripheral, each MOb must be
// "configured (ex: disabled mode - CONMOB=00)."
// Just going to configure them all as receive. Don't know that
// This is corect. Maybe they should be set to disable, but one?
// H/T http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=107164
//IDT, RTRTAG, RBnTAG
CANIDT1 = 0; //ID
CANIDT2 = 0;
CANIDT3 = 0;
CANIDT4 = 0;
//IDMSK, IDEMSK, RTRMSK
CANIDM1 = 0; //get all messages
CANIDM2 = 0; //1 = check bit
CANIDM3 = 0; //0 = ignore bit
CANIDM4 = 0; //(1<<IDEMSK); // do not ignore standard frames
//set to receive, DLC, IDE
//set MOBs 5-14 to receive. Is this anything like ideal?
if(i >= 5)
CANCDMOB = (1 << CONMOB1) | (1 << IDE);
else
CANCDMOB = 0; //(1 << IDE);
}
// activate CAN controller
CANGCON = (1 << ENASTB);
//DEG 26 May 2011
//enable individual MOB interrupts!
//For whatever reason, this does not take effect when the
//CAN bus is disabled!?
CANIE1 = 0x7F;
CANIE2 = 0xFF;
return true;
}
