C++ (Cpp) at91_serial_hw_init Beispiele

Beispiel #1

Datei: meesc.c Projekt: 12thmantec/u-boot-novena-spl

int board_init(void)
{
	/* Peripheral Clock Enable Register */
	at91_sys_write(AT91_PMC_PCER,	1 << AT91SAM9263_ID_PIOA |
					1 << AT91SAM9263_ID_PIOB |
					1 << AT91SAM9263_ID_PIOCDE);

	/* arch number of MEESC-Board */
	gd->bd->bi_arch_number = MACH_TYPE_MEESC;

	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	meesc_nand_hw_init();
#endif
	meesc_ethercat_hw_init();
#ifdef CONFIG_HAS_DATAFLASH
	at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
	meesc_macb_hw_init();
#endif
#ifdef CONFIG_AT91_CAN
	at91_can_hw_init();
#endif
	return 0;
}

Beispiel #2

Datei: som-9g20.c Projekt: sensysnetworks/u-boot-at91

int board_init(void)
{
	/* arch number of AT91SAM9G20EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

#ifdef CONFIG_CMD_NAND
	at91sam9g20ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
	at91sam9g20ek_spi_hw_init();
#endif
#ifdef CONFIG_MACB
	at91sam9g20ek_macb_hw_init();
#endif

	/** Setup MMC/SD Peripheral **/
	at91_set_A_periph(AT91_PIN_PA6,  1);
	at91_set_A_periph(AT91_PIN_PA7,  1);
	at91_set_A_periph(AT91_PIN_PA8,  0);
	at91_set_A_periph(AT91_PIN_PA9,  1);
	at91_set_A_periph(AT91_PIN_PA10, 1);
	at91_set_A_periph(AT91_PIN_PA11, 1);

	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_MCI);

	/** Setup serial ports **/
	at91_serial_hw_init();

	return 0;
}

Beispiel #3

Datei: pm9g45.c Projekt: 54shady/uboot_tiny4412

int board_init(void)
{
	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;

	/* Enable Ctrlc */
	console_init_f();

	writel((1 << AT91SAM9G45_ID_PIOA) |
		(1 << AT91SAM9G45_ID_PIOB) |
		(1 << AT91SAM9G45_ID_PIOC) |
		(1 << AT91SAM9G45_ID_PIODE), &pmc->pcer);

	/* arch number of AT91SAM9M10G45EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_PM9G45;
	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	pm9g45_nand_hw_init();
#endif

#ifdef CONFIG_MACB
	pm9g45_macb_hw_init();
#endif
	return 0;
}

Beispiel #4

Datei: at91sam9260ek.c Projekt: 12thmantec/u-boot-novena-spl

int board_init(void)
{
	/* Enable Ctrlc */
	console_init_f();

#ifdef CONFIG_AT91SAM9G20EK
	/* arch number of AT91SAM9260EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
#else
	/* arch number of AT91SAM9260EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9260EK;
#endif
	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	at91sam9260ek_nand_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
	at91_spi0_hw_init((1 << 0) || (1 << 1));
#endif
#ifdef CONFIG_MACB
	at91sam9260ek_macb_hw_init();
#endif

	return 0;
}

Beispiel #5

Datei: cpu9260.c Projekt: 247a/lenovo_b6000-8000_kernel_source

int board_init(void)
{
	/* Enable Ctrlc */
	console_init_f();

	/* arch number of the board */
#if defined(CONFIG_CPU9G20)
	gd->bd->bi_arch_number = MACH_TYPE_CPUAT9G20;
#elif defined(CONFIG_CPU9260)
	gd->bd->bi_arch_number = MACH_TYPE_CPUAT9260;
#endif

	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	cpu9260_nand_hw_init();
#endif
#ifdef CONFIG_MACB
	cpu9260_macb_hw_init();
#endif
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
	status_led_set(STATUS_LED_BOOT, STATUS_LED_ON);
#endif
	return 0;
}

Beispiel #6

Datei: afeb9260.c Projekt: kizukukoto/WDN900_GPL

int board_init(void)
{
	/* Enable Ctrlc */
	console_init_f();

	/* arch number of AT91SAM9260EK-Board */
	gd->bd->bi_arch_number = MACH_TYPE_AFEB9260;
	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	afeb9260_nand_hw_init();
#endif
	at91_spi0_hw_init((1 << 0) || (1 << 1));
#ifdef CONFIG_MACB
	afeb9260_macb_hw_init();
#endif

	return 0;
}

Beispiel #7

Datei: otc570.c Projekt: jwleung/samsung_u-boot_nowplus

int board_init(void)
{
	/* Peripheral Clock Enable Register */
	at91_sys_write(AT91_PMC_PCER,	1 << AT91SAM9263_ID_PIOA |
					1 << AT91SAM9263_ID_PIOB |
					1 << AT91SAM9263_ID_PIOCDE |
					1 << AT91SAM9263_ID_TWI |
					1 << AT91SAM9263_ID_SPI0 |
					1 << AT91SAM9263_ID_LCDC |
					1 << AT91SAM9263_ID_UHP);

	/* arch number of OTC570-Board */
	gd->bd->bi_arch_number = MACH_TYPE_OTC570;

	/* adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
	otc570_nand_hw_init();
#endif
	otc570_ethercat_hw_init();
#ifdef CONFIG_HAS_DATAFLASH
	at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_MACB
	otc570_macb_hw_init();
#endif
#ifdef CONFIG_AT91_CAN
	at91_can_hw_init();
#endif
#ifdef CONFIG_USB_OHCI_NEW
	at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
	otc570_lcd_hw_init();
#endif
	return 0;
}