void board_init(void)
{
ioport_configure_pin(LED0_GPIO,
IOPORT_DIR_OUTPUT|IOPORT_INIT_LOW|IOPORT_INV_ENABLED);
ioport_configure_pin(LED1_GPIO,
IOPORT_DIR_OUTPUT|IOPORT_INIT_LOW|IOPORT_INV_ENABLED);
ioport_configure_pin(LED2_GPIO,
IOPORT_DIR_OUTPUT|IOPORT_INIT_LOW|IOPORT_INV_ENABLED);
ioport_configure_pin(LED3_GPIO,
IOPORT_DIR_OUTPUT|IOPORT_INIT_LOW|IOPORT_INV_ENABLED);
ioport_configure_pin(BACKLIGHT_GPIO, IOPORT_DIR_OUTPUT|IOPORT_INIT_LOW);
ioport_configure_pin(LED_POWER, IOPORT_DIR_OUTPUT|IOPORT_INIT_HIGH);
ioport_configure_pin(GPIO_PUSH_BUTTON_0, IOPORT_DIR_INPUT |
IOPORT_PULL_UP);
ioport_configure_pin(GPIO_PUSH_BUTTON_1, IOPORT_DIR_INPUT |
IOPORT_PULL_UP);
ioport_configure_pin(GPIO_PUSH_BUTTON_2, IOPORT_DIR_INPUT |
IOPORT_PULL_UP);
ioport_configure_pin(GPIO_PUSH_BUTTON_3, IOPORT_DIR_INPUT |
IOPORT_PULL_UP);
#ifdef CONF_BOARD_AT45DBX
ioport_configure_pin(AT45DBX_MASTER_SCK, IOPORT_DIR_OUTPUT |
IOPORT_INIT_HIGH);
ioport_configure_pin(AT45DBX_MASTER_MOSI, IOPORT_DIR_OUTPUT |
IOPORT_INIT_HIGH);
ioport_configure_pin(AT45DBX_MASTER_MISO, IOPORT_DIR_INPUT);
ioport_configure_pin(AT45DBX_CS, IOPORT_DIR_OUTPUT | IOPORT_INIT_HIGH);
// Setting PORT_USART0_bm to one will move the pin location
// of USARTC0 (in mode SPI) from Px[3:0] to Px[7:4].
PORTC.REMAP |= PORT_USART0_bm;
#endif
#ifdef CONF_BOARD_LIGHT_SENSOR
ioport_configure_pin(LIGHT_SENSOR_SIGNAL_PIN, IOPORT_DIR_INPUT
| IOPORT_INPUT_DISABLE);
#endif
#ifdef CONF_BOARD_TEMPERATURE_SENSOR
ioport_configure_pin(TEMPERATURE_SENSOR_SIGNAL_PIN, IOPORT_DIR_INPUT
| IOPORT_INPUT_DISABLE);
#endif
#ifdef CONF_BOARD_POTENTIOMETER_SENSOR
ioport_configure_pin(POTENTIOMETER_SIGNAL_PIN, IOPORT_DIR_INPUT
| IOPORT_INPUT_DISABLE);
#endif
#ifdef CONF_BOARD_ENABLE_MXT143E_XPLAINED
ioport_configure_pin(MXT143E_XPLAINED_SCK, IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(MXT143E_XPLAINED_MOSI, IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(MXT143E_XPLAINED_MISO, IOPORT_DIR_INPUT);
ioport_configure_pin(MXT143E_XPLAINED_CS, IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(MXT143E_XPLAINED_CHG, IOPORT_DIR_INPUT);
ioport_configure_pin(MXT143E_XPLAINED_DC, IOPORT_DIR_OUTPUT
| IOPORT_INIT_LOW);
#ifndef MXT143E_XPLAINED_BACKLIGHT_DISABLE
ioport_configure_pin(MXT143E_XPLAINED_BACKLIGHT, IOPORT_DIR_OUTPUT
| IOPORT_INIT_LOW);
#endif
ioport_configure_pin(MXT143E_XPLAINED_LCD_RESET, IOPORT_DIR_OUTPUT
| IOPORT_INIT_LOW);
// Setting PORT_USART0_bm to one will move the pin location
// of USARTC0 (in mode SPI) from Px[3:0] to Px[7:4].
PORTC.REMAP |= PORT_USART0_bm;
#endif
#ifdef CONF_BOARD_LCD_BACKLIGHT_PWM
backlight_start_pwm();
#endif
#ifdef CONF_BOARD_ENABLE_USARTC0
ioport_configure_pin(IOPORT_CREATE_PIN(PORTC, 3), IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(IOPORT_CREATE_PIN(PORTC, 2), IOPORT_DIR_INPUT);
#endif
#ifdef CONF_BOARD_ENABLE_USARTE0
/* Note: this will disable touch buttons 2 and 3 as they share the same
* physical pins at the USART E module. */
ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 3), IOPORT_DIR_OUTPUT
| IOPORT_INIT_HIGH);
ioport_configure_pin(IOPORT_CREATE_PIN(PORTE, 2), IOPORT_DIR_INPUT);
#endif
#if defined (SENSORS_XPLAINED_BOARD)
/* Configure the Xplained Sensor extension board, if any, after
* the platform Xplained board has configured basic clock settings,
* GPIO pin mapping, interrupt controller options, etc.
*/
sensor_board_init ();
#endif
}
void ui_wakeup(void)
{
backlight_start_pwm();
adc_enable(&LIGHT_SENSOR_ADC_MODULE);
led_power_on();
}
