static void __init bahamas_init(void)
{
int rc;
printk("bahamas_init() revision=%d\n", system_rev);
/*
* Setup common MSM GPIOS
*/
sdc1_boot_reset();
// printk("\n\nboard-mega.c: sdc1 boot reset\n\n");
config_gpios();
// printk("\n\nboard-mega.c: config gpios\n\n");
msm_hw_reset_hook = bahamas_reset;
// printk("\n\nboard-mega.c: msm hw reset hook\n\n");
msm_acpu_clock_init(&bahamas_clock_data);
// printk("\n\nmsm acpu clock init\n\n");
perflock_init(&bahamas_perflock_data);
// printk("\n\nperflock init\n\n");
/* adjust GPIOs based on bootloader request */
/* XXX: on Memphis,
* GPIO#86 is H2W DAT / UART RX for HTC 11-Pin
* GPIO#87 is H2W CLK / UART TX for HTC 11-Pin
* We would need to use UART3 as debug port
*
* TODO: switch UART3 and H2W (for headset detect)
* based on bootloader request.
*/
/*#if defined(CONFIG_MSM_SERIAL_DEBUGGER)
if (!opt_disable_uart3)
msm_serial_debug_init(MSM_UART3_PHYS, INT_UART3,
&msm_device_uart3.dev, 1);
#endif*/
/* touchscreen must be powered before we enable i2c pullup */
#if 0 /* TODO: do some equivalent operations here */
udelay(50);
trout_gpio_write(NULL, TROUT_GPIO_I2C_PULL, 1);
#endif
/* put the AF VCM in powerdown mode to avoid noise */
#if 0
trout_gpio_write(NULL, TROUT_GPIO_VCM_PWDN, 1);
mdelay(100);
trout_i2c_sysdev_resume(NULL);
#endif
#if 0 /* TODO: do some equivalent operations here */
if(sysdev_class_register(&trout_i2c_sysdev_class) == 0)
sysdev_register(&trout_i2c_sys_device);
#endif
#ifdef CONFIG_SERIAL_MSM_HS
msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
msm_add_serial_devices(3);
#else
msm_add_serial_devices(0);
#endif
msm_add_serial_devices(2);
msm_add_usb_devices(NULL,NULL);
//msm_change_usb_id(0x0bb4, 0x0c06);
if (board_mcp_monodie())
msm_add_mem_devices(&pmem_setting_monodie);
else
msm_add_mem_devices(&pmem_setting_dualdie);
msm_init_pmic_vibrator();
// printk("\n\nboard-mega.c: msm init pmic vibrator\n\n");
bahamas_init_h2w_power_gpio();
// printk("\n\nboard-mega.c: bahamas init h2w power gpio\n\n");
//#if 1
rc = bahamas_init_mmc(system_rev);
// printk("\n\nboard-mega.c: init mmc\n\n");
if (rc)
printk(KERN_CRIT "%s: MMC init failure (%d)\n", __func__, rc);
//#endif
if(!system_rev)
bahamas_reset_keys_device.dev.platform_data = &bahamas_reset_keys_pdata0;
/*CC090319*/
/* if (bahamas_is_3M_camera()) {
msm_camera_device_data.sinfo = &msm_camera_sensor_mt9t013;
}
else {
msm_camera_device_data.sinfo = &msm_camera_sensor_s5k4b2fx;
}*/
if(system_rev < 3) {
if (panel_detect() == PANEL_WINTEK) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_0_wint);
microp_data.pin_config = microp_pins_0_wint;
} else {
microp_data.num_pins = ARRAY_SIZE(microp_pins_0);
microp_data.pin_config = microp_pins_0;
}
i2c_microp_devices.irq = 0;
} else if (panel_detect() == PANEL_WINTEK) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_1_wint);
microp_data.pin_config = microp_pins_1_wint;
}
/*~CC090319*/
//platform_add_devices(devices, ARRAY_SIZE(devices));
/* Read Config 8 200 (Full Speed USB Mode) */
/*if (readl(MSM_SHARED_RAM_BASE + 0xFC054) & 0x200)
bahamas_h2w_data.flags |= FULL_SPEED_USB;
if (system_rev >= 3)
bahamas_h2w_data.flags |= _35MM_MIC_DET_L2H;
/* if (system_rev >= 5)
i2c_register_board_info(0, i2c_sensor, ARRAY_SIZE(i2c_sensor));
i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
i2c_register_board_info(0 ,&i2c_microp_devices, 1);
/* SD card door should wake the device */
//trout_gpio_irq_set_wake(TROUT_GPIO_TO_INT(TROUT_GPIO_SD_DOOR_N), 1);
msm_hsusb_set_vbus_state(1);
}
static void __init bahamas_init(void)
{
int rc;
char *cid = NULL;
printk("bahamas_init() revision = 0x%X\n", system_rev);
printk(KERN_INFO "mfg_mode=%d\n", board_mfg_mode());
msm_clock_init();
board_get_cid_tag(&cid);
/*
* Setup common MSM GPIOS
*/
config_gpios();
gpio_request(BAHAMAS_GPIO_CABLE_IN2, "gpio_cable_in2");
gpio_request(BAHAMAS_GPIO_AUD_EXTMIC_SEL, "gpio_aud_extmic_sel");
gpio_request(BAHAMAS_GPIO_WFM_ANT_SW, "gpio_wfm_ant_sw");
msm_hw_reset_hook = bahamas_reset;
msm_acpu_clock_init(&bahamas_clock_data);
#if defined(CONFIG_PERFLOCK)
perflock_init(&bahamas_perflock_data);
#endif
#if defined(CONFIG_MSM_SERIAL_DEBUGGER)
if (!opt_disable_uart3)
msm_serial_debug_init(MSM_UART3_PHYS, INT_UART3,
&msm_device_uart3.dev, 1,
MSM_GPIO_TO_INT(BAHAMAS_GPIO_UART3_RX));
#endif
msm_add_devices();
#if defined(CONFIG_SERIAL_MSM_HS)
msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
msm_add_serial_devices(3);
#else
msm_add_serial_devices(0);
#endif
msm_add_serial_devices(2);
#if defined(CONFIG_USB_FUNCTION)
msm_register_usb_phy_init_seq(bahamas_phy_init_seq);
msm_add_usb_devices(bahamas_phy_reset, NULL);
#endif
#if defined(CONFIG_USB_ANDROID)
android_usb_pdata.products[0].product_id =
android_usb_pdata.product_id;
android_usb_pdata.serial_number = board_serialno();
msm_hsusb_pdata.serial_number = board_serialno();
msm_device_hsusb.dev.platform_data = &msm_hsusb_pdata;
platform_device_register(&msm_device_hsusb);
#if defined(CONFIG_USB_ANDROID_RNDIS)
platform_device_register(&rndis_device);
#endif
platform_device_register(&usb_mass_storage_device);
platform_device_register(&android_usb_device);
#endif
if (board_mcp_monodie())
msm_add_mem_devices(&pmem_setting_monodie);
else
msm_add_mem_devices(&pmem_setting_dualdie);
bahamas_init_h2w_power_gpio();
rc = bahamas_init_mmc(system_rev);
if (rc)
printk(KERN_CRIT "%s: MMC init failure (%d)\n", __func__, rc);
if(system_rev < 3) {
if (panel_detect() == PANEL_WINTEK) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_0_wint);
microp_data.pin_config = microp_pins_0_wint;
} else {
microp_data.num_pins = ARRAY_SIZE(microp_pins_0);
microp_data.pin_config = microp_pins_0;
}
i2c_microp_devices.irq = 0;
} else if (panel_detect() == PANEL_WINTEK) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_1_wint);
microp_data.pin_config = microp_pins_1_wint;
}
msm_device_i2c_init();
platform_add_devices(devices, ARRAY_SIZE(devices));
if (system_rev >= 3)
bahamas_h2w_data.flags |= _35MM_MIC_DET_L2H;
i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
i2c_register_board_info(0 ,&i2c_microp_devices, 1);
bahamas_init_keypad();
bahamas_init_panel();
msm_init_pmic_vibrator(3000);
}
