static int mx31_config(struct spi_imx_data *spi_imx,
struct spi_imx_config *config)
{
unsigned int reg = MX31_CSPICTRL_ENABLE | MX31_CSPICTRL_MASTER;
reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, config->speed_hz) <<
MX31_CSPICTRL_DR_SHIFT;
if (cpu_is_mx31())
reg |= (config->bpw - 1) << MX31_CSPICTRL_BC_SHIFT;
else if (cpu_is_mx25() || cpu_is_mx35()) {
reg |= (config->bpw - 1) << MX35_CSPICTRL_BL_SHIFT;
reg |= MX31_CSPICTRL_SSCTL;
}
if (config->mode & SPI_CPHA)
reg |= MX31_CSPICTRL_PHA;
if (config->mode & SPI_CPOL)
reg |= MX31_CSPICTRL_POL;
if (config->mode & SPI_CS_HIGH)
reg |= MX31_CSPICTRL_SSPOL;
if (config->cs < 0) {
if (cpu_is_mx31())
reg |= (config->cs + 32) << MX31_CSPICTRL_CS_SHIFT;
else if (cpu_is_mx25() || cpu_is_mx35())
reg |= (config->cs + 32) << MX35_CSPICTRL_CS_SHIFT;
}
writel(reg, spi_imx->base + MXC_CSPICTRL);
return 0;
}
static int __init mx3_devices_init(void)
{
if (cpu_is_mx31()) {
mxc_nand_resources[0].start = MX31_NFC_BASE_ADDR;
mxc_nand_resources[0].end = MX31_NFC_BASE_ADDR + 0xfff;
imx_wdt_resources[0].start = MX31_WDOG_BASE_ADDR;
imx_wdt_resources[0].end = MX31_WDOG_BASE_ADDR + 0x3fff;
mxc_register_device(&mxc_rnga_device, NULL);
}
if (cpu_is_mx35()) {
mxc_nand_resources[0].start = MX35_NFC_BASE_ADDR;
mxc_nand_resources[0].end = MX35_NFC_BASE_ADDR + 0x1fff;
otg_resources[0].start = MX35_OTG_BASE_ADDR;
otg_resources[0].end = MX35_OTG_BASE_ADDR + 0x1ff;
otg_resources[1].start = MXC_INT_USBOTG;
otg_resources[1].end = MXC_INT_USBOTG;
mxc_usbh1_resources[0].start = MX35_OTG_BASE_ADDR + 0x400;
mxc_usbh1_resources[0].end = MX35_OTG_BASE_ADDR + 0x5ff;
mxc_usbh1_resources[1].start = MXC_INT_USBHS;
mxc_usbh1_resources[1].end = MXC_INT_USBHS;
imx_ssi_resources0[1].start = MX35_INT_SSI1;
imx_ssi_resources0[1].end = MX35_INT_SSI1;
imx_ssi_resources1[1].start = MX35_INT_SSI2;
imx_ssi_resources1[1].end = MX35_INT_SSI2;
imx_wdt_resources[0].start = MX35_WDOG_BASE_ADDR;
imx_wdt_resources[0].end = MX35_WDOG_BASE_ADDR + 0x3fff;
}
return 0;
}
void pmic_voltage_init(void)
{
t_regulator_voltage volt;
/* Enable 4 mc13783 output voltages */
pmic_write_reg(REG_ARBITRATION_SWITCHERS, (1 << 5), (1 << 5));
/* Set mc13783 DVS speed 25mV each 4us */
pmic_write_reg(REG_SWITCHERS_4, (0 << 6), (3 << 6));
if (cpu_is_mx31())
volt.sw1a = SW1A_1_625V;
else
volt.sw1a = SW1A_1_425V;
pmic_power_regulator_set_voltage(SW_SW1A, volt);
volt.sw1a = SW1A_1_25V;
pmic_power_switcher_set_dvs(SW_SW1A, volt);
if (cpu_is_mx32()) {
volt.sw1a = SW1A_0_975V;
pmic_power_switcher_set_stby(SW_SW1A, volt);
}
volt.sw1b = SW1A_1_25V;
pmic_power_switcher_set_dvs(SW_SW1B, volt);
volt.sw1b = SW1A_1_25V;
pmic_power_switcher_set_stby(SW_SW1B, volt);
}
static void mxc_init_nand_mtd(void)
{
if (__raw_readl(MXC_CCM_RCSR) & MXC_CCM_RCSR_NF16B) {
mxc_nand_data.width = 2;
}
if (cpu_is_mx31()) {
(void)platform_device_register(&mxc_nand_mtd_device);
}
if (cpu_is_mx32()) {
(void)platform_device_register(&mxc_nandv2_mtd_device);
}
}
int mxc_set_usbcontrol(int port, unsigned int flags)
{
unsigned int v;
if (cpu_is_mx31()) {
v = readl(IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_OTG_SIC_SHIFT;
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v |= MX31_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H1_SIC_SHIFT;
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v |= MX31_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H2_DT_BIT;
break;
}
writel(v, IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
printk(KERN_WARNING
"%s() unable to setup USBCONTROL for this CPU\n", __func__);
return -EINVAL;
}
static int post_cpu_init(void)
{
#ifdef CONFIG_MACH_MX27
if (cpu_is_mx27())
ipipe_mach_allow_hwtimer_uaccess(MX27_IO_P2V(MX27_AIPI_BASE_ADDR), 3);
#endif /* CONFIG_MACH_MX27 */
#ifdef CONFIG_MACH_MX25
if (cpu_is_mx25())
ipipe_mach_allow_hwtimer_uaccess(MX25_AIPS1_BASE_ADDR_VIRT,
MX25_AIPS2_BASE_ADDR_VIRT);
#endif /* CONFIG_MACH_MX25 */
#ifdef CONFIG_MACH_MX31
if (cpu_is_mx31())
ipipe_mach_allow_hwtimer_uaccess(AIPS1_BASE_ADDR_VIRT,
AIPS2_BASE_ADDR_VIRT);
#endif /* CONFIG_MACH_MX31 */
return 0;
}
static int mxc_audmux_v2_init(void)
{
int ret;
if (cpu_is_mx35()) {
audmux_clk = clk_get(NULL, "audmux");
if (IS_ERR(audmux_clk)) {
ret = PTR_ERR(audmux_clk);
printk(KERN_ERR "%s: cannot get clock: %d\n", __func__,
ret);
return ret;
}
}
if (cpu_is_mx31() || cpu_is_mx35())
audmux_base = IO_ADDRESS(AUDMUX_BASE_ADDR);
return 0;
}
static int mxc_init_l2x0(void)
{
void __iomem *l2x0_base;
void __iomem *clkctl_base;
if (!cpu_is_mx31() && !cpu_is_mx35())
return 0;
/*
* First of all, we must repair broken chip settings. There are some
* i.MX35 CPUs in the wild, comming with bogus L2 cache settings. These
* misconfigured CPUs will run amok immediately when the L2 cache gets enabled.
* Workaraound is to setup the correct register setting prior enabling the
* L2 cache. This should not hurt already working CPUs, as they are using the
* same value.
*/
#define L2_MEM_VAL 0x10
clkctl_base = ioremap(MX35_CLKCTL_BASE_ADDR, 4096);
if (clkctl_base != NULL) {
writel(0x00000515, clkctl_base + L2_MEM_VAL);
iounmap(clkctl_base);
} else {
pr_err("L2 cache: Cannot fix timing. Trying to continue without\n");
}
l2x0_base = ioremap(MX3x_L2CC_BASE_ADDR, 4096);
if (IS_ERR(l2x0_base)) {
printk(KERN_ERR "remapping L2 cache area failed with %ld\n",
PTR_ERR(l2x0_base));
return 0;
}
l2x0_init(l2x0_base, 0x00030024, 0x00000000);
return 0;
}
int mxc_initialize_usb_hw(int port, unsigned int flags)
{
unsigned int v;
#if defined(CONFIG_ARCH_MX25)
if (cpu_is_mx25()) {
v = readl(MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX35_H1_TLL_BIT;
if (flags & MXC_EHCI_INTERNAL_PHY)
v |= MX35_H1_USBTE_BIT;
if (flags & MXC_EHCI_IPPUE_DOWN)
v |= MX35_H1_IPPUE_DOWN_BIT;
if (flags & MXC_EHCI_IPPUE_UP)
v |= MX35_H1_IPPUE_UP_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_ARCH_MX25 */
#if defined(CONFIG_ARCH_MX3)
if (cpu_is_mx31()) {
v = readl(MX31_IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H2_DT_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX31_IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
if (cpu_is_mx35()) {
v = readl(MX35_IO_ADDRESS(MX35_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX35_H1_TLL_BIT;
if (flags & MXC_EHCI_INTERNAL_PHY)
v |= MX35_H1_USBTE_BIT;
if (flags & MXC_EHCI_IPPUE_DOWN)
v |= MX35_H1_IPPUE_DOWN_BIT;
if (flags & MXC_EHCI_IPPUE_UP)
v |= MX35_H1_IPPUE_UP_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX35_IO_ADDRESS(MX35_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_ARCH_MX3 */
#ifdef CONFIG_MACH_MX27
if (cpu_is_mx27()) {
/* On i.MX27 we can use the i.MX31 USBCTRL bits, they
* are identical
*/
v = readl(MX27_IO_ADDRESS(MX27_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H2_DT_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX27_IO_ADDRESS(MX27_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_MACH_MX27 */
#ifdef CONFIG_ARCH_MX51
if (cpu_is_mx51()) {
void __iomem *usb_base;
u32 usbotg_base;
u32 usbother_base;
int ret = 0;
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
switch (port) {
case 0: /* OTG port */
usbotg_base = usb_base + MXC_OTG_OFFSET;
break;
case 1: /* Host 1 port */
usbotg_base = usb_base + MXC_H1_OFFSET;
break;
default:
printk(KERN_ERR"%s no such port %d\n", __func__, port);
ret = -ENOENT;
goto error;
}
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
switch (port) {
case 0: /*OTG port */
if (flags & MXC_EHCI_INTERNAL_PHY) {
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v |= (MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is not used */
else
v &= ~(MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is used */
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
if (flags & MXC_EHCI_WAKEUP_ENABLED)
v |= MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup enable */
else
v &= ~MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup disable */
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
}
break;
case 1: /* Host 1 */
/*Host ULPI */
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
if (flags & MXC_EHCI_WAKEUP_ENABLED)
v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
else
v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
else
v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
else
v |= MXC_H1_OC_DIS_BIT; /* OC is not used */
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
v = __raw_readl(usbotg_base + MXC_USBCMD_OFFSET);
if (flags & MXC_EHCI_ITC_NO_THRESHOLD)
/* Interrupt Threshold Control:Immediate (no threshold) */
v &= MXC_UCMD_ITC_NO_THRESHOLD_MASK;
__raw_writel(v, usbotg_base + MXC_USBCMD_OFFSET);
break;
}
error:
iounmap(usb_base);
return ret;
}
#endif
printk(KERN_WARNING
"%s() unable to setup USBCONTROL for this CPU\n", __func__);
return -EINVAL;
}
static int __devinit spi_imx_probe(struct platform_device *pdev)
{
struct spi_imx_master *mxc_platform_info;
struct spi_master *master;
struct spi_imx_data *spi_imx;
struct resource *res;
int i, ret;
mxc_platform_info = dev_get_platdata(&pdev->dev);
if (!mxc_platform_info) {
dev_err(&pdev->dev, "can't get the platform data\n");
return -EINVAL;
}
master = spi_alloc_master(&pdev->dev, sizeof(struct spi_imx_data));
if (!master)
return -ENOMEM;
platform_set_drvdata(pdev, master);
master->bus_num = pdev->id;
master->num_chipselect = mxc_platform_info->num_chipselect;
spi_imx = spi_master_get_devdata(master);
spi_imx->bitbang.master = spi_master_get(master);
spi_imx->chipselect = mxc_platform_info->chipselect;
for (i = 0; i < master->num_chipselect; i++) {
if (spi_imx->chipselect[i] < 0)
continue;
ret = gpio_request(spi_imx->chipselect[i], DRIVER_NAME);
if (ret) {
while (i > 0) {
i--;
if (spi_imx->chipselect[i] >= 0)
gpio_free(spi_imx->chipselect[i]);
}
dev_err(&pdev->dev, "can't get cs gpios\n");
goto out_master_put;
}
}
spi_imx->bitbang.chipselect = spi_imx_chipselect;
spi_imx->bitbang.setup_transfer = spi_imx_setupxfer;
spi_imx->bitbang.txrx_bufs = spi_imx_transfer;
spi_imx->bitbang.master->setup = spi_imx_setup;
spi_imx->bitbang.master->cleanup = spi_imx_cleanup;
spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
init_completion(&spi_imx->xfer_done);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "can't get platform resource\n");
ret = -ENOMEM;
goto out_gpio_free;
}
if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
dev_err(&pdev->dev, "request_mem_region failed\n");
ret = -EBUSY;
goto out_gpio_free;
}
spi_imx->base = ioremap(res->start, resource_size(res));
if (!spi_imx->base) {
ret = -EINVAL;
goto out_release_mem;
}
spi_imx->irq = platform_get_irq(pdev, 0);
if (spi_imx->irq <= 0) {
ret = -EINVAL;
goto out_iounmap;
}
ret = request_irq(spi_imx->irq, spi_imx_isr, 0, DRIVER_NAME, spi_imx);
if (ret) {
dev_err(&pdev->dev, "can't get irq%d: %d\n", spi_imx->irq, ret);
goto out_iounmap;
}
if (cpu_is_mx25() || cpu_is_mx31() || cpu_is_mx35()) {
spi_imx->intctrl = mx31_intctrl;
spi_imx->config = mx31_config;
spi_imx->trigger = mx31_trigger;
spi_imx->rx_available = mx31_rx_available;
} else if (cpu_is_mx27() || cpu_is_mx21()) {
spi_imx->intctrl = mx27_intctrl;
spi_imx->config = mx27_config;
spi_imx->trigger = mx27_trigger;
spi_imx->rx_available = mx27_rx_available;
} else if (cpu_is_mx1()) {
spi_imx->intctrl = mx1_intctrl;
spi_imx->config = mx1_config;
spi_imx->trigger = mx1_trigger;
spi_imx->rx_available = mx1_rx_available;
} else
BUG();
spi_imx->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(spi_imx->clk)) {
dev_err(&pdev->dev, "unable to get clock\n");
ret = PTR_ERR(spi_imx->clk);
goto out_free_irq;
}
clk_enable(spi_imx->clk);
spi_imx->spi_clk = clk_get_rate(spi_imx->clk);
if (cpu_is_mx1() || cpu_is_mx21() || cpu_is_mx27())
writel(1, spi_imx->base + MXC_RESET);
/* drain receive buffer */
if (cpu_is_mx25() || cpu_is_mx31() || cpu_is_mx35())
while (readl(spi_imx->base + MX3_CSPISTAT) & MX3_CSPISTAT_RR)
readl(spi_imx->base + MXC_CSPIRXDATA);
spi_imx->intctrl(spi_imx, 0);
ret = spi_bitbang_start(&spi_imx->bitbang);
if (ret) {
dev_err(&pdev->dev, "bitbang start failed with %d\n", ret);
goto out_clk_put;
}
dev_info(&pdev->dev, "probed\n");
return ret;
out_clk_put:
clk_disable(spi_imx->clk);
clk_put(spi_imx->clk);
out_free_irq:
free_irq(spi_imx->irq, spi_imx);
out_iounmap:
iounmap(spi_imx->base);
out_release_mem:
release_mem_region(res->start, resource_size(res));
out_gpio_free:
for (i = 0; i < master->num_chipselect; i++)
if (spi_imx->chipselect[i] >= 0)
gpio_free(spi_imx->chipselect[i]);
out_master_put:
spi_master_put(master);
kfree(master);
platform_set_drvdata(pdev, NULL);
return ret;
}
static int __devinit spi_imx_probe(struct platform_device *pdev)
{
struct spi_imx_master *mxc_platform_info;
struct spi_master *master;
struct spi_imx_data *spi_imx;
struct resource *res;
int i, ret;
mxc_platform_info = dev_get_platdata(&pdev->dev);
if (!mxc_platform_info) {
dev_err(&pdev->dev, "can't get the platform data\n");
return -EINVAL;
}
master = spi_alloc_master(&pdev->dev, sizeof(struct spi_imx_data));
if (!master)
return -ENOMEM;
platform_set_drvdata(pdev, master);
master->bus_num = pdev->id;
master->num_chipselect = mxc_platform_info->num_chipselect;
spi_imx = spi_master_get_devdata(master);
spi_imx->bitbang.master = spi_master_get(master);
spi_imx->chipselect = mxc_platform_info->chipselect;
for (i = 0; i < master->num_chipselect; i++) {
if (spi_imx->chipselect[i] < 0)
continue;
ret = gpio_request(spi_imx->chipselect[i], DRIVER_NAME);
if (ret) {
while (i > 0) {
i--;
if (spi_imx->chipselect[i] >= 0)
gpio_free(spi_imx->chipselect[i]);
}
dev_err(&pdev->dev, "can't get cs gpios\n");
goto out_master_put;
}
}
spi_imx->bitbang.chipselect = spi_imx_chipselect;
spi_imx->bitbang.setup_transfer = spi_imx_setupxfer;
spi_imx->bitbang.txrx_bufs = spi_imx_transfer;
spi_imx->bitbang.master->setup = spi_imx_setup;
spi_imx->bitbang.master->cleanup = spi_imx_cleanup;
spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
init_completion(&spi_imx->xfer_done);
if (pdev->id_entry->driver_data == SPI_IMX_VER_AUTODETECT) {
if (cpu_is_mx25() || cpu_is_mx35())
spi_imx->devtype_data =
spi_imx_devtype_data[SPI_IMX_VER_0_7];
else if (cpu_is_mx25() || cpu_is_mx31() || cpu_is_mx35())
spi_imx->devtype_data =
spi_imx_devtype_data[SPI_IMX_VER_0_4];
else if (cpu_is_mx27() || cpu_is_mx21())
spi_imx->devtype_data =
spi_imx_devtype_data[SPI_IMX_VER_0_0];
else if (cpu_is_mx1())
spi_imx->devtype_data =
spi_imx_devtype_data[SPI_IMX_VER_IMX1];
else
BUG();
} else
spi_imx->devtype_data =
spi_imx_devtype_data[pdev->id_entry->driver_data];
if (!spi_imx->devtype_data.intctrl) {
dev_err(&pdev->dev, "no support for this device compiled in\n");
ret = -ENODEV;
goto out_gpio_free;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "can't get platform resource\n");
ret = -ENOMEM;
goto out_gpio_free;
}
if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
dev_err(&pdev->dev, "request_mem_region failed\n");
ret = -EBUSY;
goto out_gpio_free;
}
spi_imx->base = ioremap(res->start, resource_size(res));
if (!spi_imx->base) {
ret = -EINVAL;
goto out_release_mem;
}
spi_imx->irq = platform_get_irq(pdev, 0);
if (spi_imx->irq <= 0) {
ret = -EINVAL;
goto out_iounmap;
}
ret = request_irq(spi_imx->irq, spi_imx_isr, 0, DRIVER_NAME, spi_imx);
if (ret) {
dev_err(&pdev->dev, "can't get irq%d: %d\n", spi_imx->irq, ret);
goto out_iounmap;
}
spi_imx->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(spi_imx->clk)) {
dev_err(&pdev->dev, "unable to get clock\n");
ret = PTR_ERR(spi_imx->clk);
goto out_free_irq;
}
clk_enable(spi_imx->clk);
spi_imx->spi_clk = clk_get_rate(spi_imx->clk);
spi_imx->devtype_data.reset(spi_imx);
spi_imx->devtype_data.intctrl(spi_imx, 0);
ret = spi_bitbang_start(&spi_imx->bitbang);
if (ret) {
dev_err(&pdev->dev, "bitbang start failed with %d\n", ret);
goto out_clk_put;
}
dev_info(&pdev->dev, "probed\n");
return ret;
out_clk_put:
clk_disable(spi_imx->clk);
clk_put(spi_imx->clk);
out_free_irq:
free_irq(spi_imx->irq, spi_imx);
out_iounmap:
iounmap(spi_imx->base);
out_release_mem:
release_mem_region(res->start, resource_size(res));
out_gpio_free:
for (i = 0; i < master->num_chipselect; i++)
if (spi_imx->chipselect[i] >= 0)
gpio_free(spi_imx->chipselect[i]);
out_master_put:
spi_master_put(master);
kfree(master);
platform_set_drvdata(pdev, NULL);
return ret;
}
