void mainboard_early_init(int s3resume)
{
/* Do ec reset as early as possible, but skip it on S3 resume */
if (!s3resume) {
early_ec_init();
}
}
void main(unsigned long bist)
{
int boot_mode = 0;
int cbmem_was_initted;
struct pei_data pei_data = {
.pei_version = PEI_VERSION,
.mchbar = (uintptr_t)DEFAULT_MCHBAR,
.dmibar = (uintptr_t)DEFAULT_DMIBAR,
.epbar = DEFAULT_EPBAR,
.pciexbar = CONFIG_MMCONF_BASE_ADDRESS,
.smbusbar = SMBUS_IO_BASE,
.wdbbar = 0x4000000,
.wdbsize = 0x1000,
.hpet_address = CONFIG_HPET_ADDRESS,
.rcba = (uintptr_t)DEFAULT_RCBABASE,
.pmbase = DEFAULT_PMBASE,
.gpiobase = DEFAULT_GPIOBASE,
.thermalbase = 0xfed08000,
.system_type = 0, // 0 Mobile, 1 Desktop/Server
.tseg_size = CONFIG_SMM_TSEG_SIZE,
.spd_addresses = { 0xA0, 0x00,0xA4,0x00 },
.ts_addresses = { 0x00, 0x00, 0x00, 0x00 },
.ec_present = 1,
// 0 = leave channel enabled
// 1 = disable dimm 0 on channel
// 2 = disable dimm 1 on channel
// 3 = disable dimm 0+1 on channel
.dimm_channel0_disabled = 2,
.dimm_channel1_disabled = 2,
.max_ddr3_freq = 1600,
.usb_port_config = {
/* enabled usb oc pin length */
{ 1, 0, 0x0040 }, /* P0: USB 3.0 1 (OC0) */
{ 1, 0, 0x0040 }, /* P1: USB 3.0 2 (OC0) */
{ 0, 1, 0x0000 }, /* P2: Empty */
{ 1, 1, 0x0040 }, /* P3: Camera (no OC) */
{ 1, 1, 0x0040 }, /* P4: WLAN (no OC) */
{ 1, 1, 0x0040 }, /* P5: WWAN (no OC) */
{ 0, 1, 0x0000 }, /* P6: Empty */
{ 0, 1, 0x0000 }, /* P7: Empty */
{ 0, 5, 0x0000 }, /* P8: Empty */
{ 1, 4, 0x0040 }, /* P9: USB 2.0 (AUO4) (OC4) */
{ 0, 5, 0x0000 }, /* P10: Empty */
{ 0, 5, 0x0000 }, /* P11: Empty */
{ 0, 5, 0x0000 }, /* P12: Empty */
{ 1, 5, 0x0040 }, /* P13: Bluetooth (no OC) */
},
.usb3 = {
.mode = XHCI_MODE,
.hs_port_switch_mask = XHCI_PORTS,
.preboot_support = XHCI_PREBOOT,
.xhci_streams = XHCI_STREAMS,
},
};
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
if (bist == 0)
enable_lapic();
pch_enable_lpc();
/* Enable GPIOs */
pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE|1);
pci_write_config8(PCH_LPC_DEV, GPIO_CNTL, 0x10);
setup_pch_gpios(&stout_gpio_map);
/* Initialize console device(s) */
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG, "soft reset detected\n");
boot_mode = 1;
/* System is not happy after keyboard reset... */
printk(BIOS_DEBUG, "Issuing CF9 warm reset\n");
outb(0x6, 0xcf9);
halt();
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
sandybridge_early_initialization(SANDYBRIDGE_MOBILE);
printk(BIOS_DEBUG, "Back from sandybridge_early_initialization()\n");
boot_mode = southbridge_detect_s3_resume() ? 2 : 0;
/* Do ec reset as early as possible, but skip it on S3 resume */
if (boot_mode < 2)
early_ec_init();
post_code(0x38);
/* Enable SPD ROMs and DDR-III DRAM */
enable_smbus();
/* Prepare USB controller early in S3 resume */
if (boot_mode == 2)
enable_usb_bar();
post_code(0x39);
post_code(0x3a);
pei_data.boot_mode = boot_mode;
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(&pei_data);
timestamp_add_now(TS_AFTER_INITRAM);
post_code(0x3b);
/* Perform some initialization that must run before stage2 */
early_pch_init();
post_code(0x3c);
rcba_config();
post_code(0x3d);
quick_ram_check();
post_code(0x3e);
cbmem_was_initted = !cbmem_recovery(boot_mode==2);
if (boot_mode!=2)
save_mrc_data(&pei_data);
if (boot_mode==2 && !cbmem_was_initted) {
/* Failed S3 resume, reset to come up cleanly */
outb(0x6, 0xcf9);
halt();
}
northbridge_romstage_finalize(boot_mode==2);
post_code(0x3f);
#if CONFIG_CHROMEOS
init_chromeos(boot_mode);
#endif
timestamp_add_now(TS_END_ROMSTAGE);
}
