void enable_board_pin_mux(void)
{
enable_uart3_pin_mux();
configure_module_pin_mux(nand_pin_mux);
configure_module_pin_mux(ethernet_pin_mux);
configure_module_pin_mux(gpios_pin_mux);
}
void set_uart_mux_conf(void)
{
#if CONFIG_CONS_INDEX == 1
enable_uart0_pin_mux();
#elif CONFIG_CONS_INDEX == 2
enable_uart1_pin_mux();
#elif CONFIG_CONS_INDEX == 3
enable_uart2_pin_mux();
#elif CONFIG_CONS_INDEX == 4
enable_uart3_pin_mux();
#elif CONFIG_CONS_INDEX == 5
enable_uart4_pin_mux();
#elif CONFIG_CONS_INDEX == 6
enable_uart5_pin_mux();
#endif
}
void set_uart_mux_conf(void)
{
#ifdef CONFIG_SERIAL1
enable_uart0_pin_mux();
#endif /* CONFIG_SERIAL1 */
#ifdef CONFIG_SERIAL2
enable_uart1_pin_mux();
#endif /* CONFIG_SERIAL2 */
#ifdef CONFIG_SERIAL3
enable_uart2_pin_mux();
#endif /* CONFIG_SERIAL3 */
#ifdef CONFIG_SERIAL4
enable_uart3_pin_mux();
#endif /* CONFIG_SERIAL4 */
#ifdef CONFIG_SERIAL5
enable_uart4_pin_mux();
#endif /* CONFIG_SERIAL5 */
#ifdef CONFIG_SERIAL6
enable_uart5_pin_mux();
#endif /* CONFIG_SERIAL6 */
}
void enable_uart_pin_mux(u32 addr)
{
switch (addr) {
case CONFIG_SYS_NS16550_COM1:
enable_uart0_pin_mux();
break;
case CONFIG_SYS_NS16550_COM2:
enable_uart1_pin_mux();
break;
case CONFIG_SYS_NS16550_COM3:
enable_uart2_pin_mux();
break;
case CONFIG_SYS_NS16550_COM4:
enable_uart3_pin_mux();
break;
case CONFIG_SYS_NS16550_COM5:
enable_uart4_pin_mux();
break;
case CONFIG_SYS_NS16550_COM6:
enable_uart5_pin_mux();
break;
}
}
/*
* early system init of muxing and clocks.
*/
void s_init(void)
{
/* WDT1 is already running when the bootloader gets control
* Disable it to avoid "random" resets
*/
writel(0xAAAA, &wdtimer->wdtwspr);
while (readl(&wdtimer->wdtwwps) != 0x0)
;
writel(0x5555, &wdtimer->wdtwspr);
while (readl(&wdtimer->wdtwwps) != 0x0)
;
#ifdef CONFIG_SPL_BUILD
/* Setup the PLLs and the clocks for the peripherals */
pll_init();
/* Enable RTC32K clock */
rtc32k_enable();
/* UART softreset */
u32 regVal;
#ifdef CONFIG_SERIAL1
enable_uart0_pin_mux();
#endif /* CONFIG_SERIAL1 */
#ifdef CONFIG_SERIAL2
enable_uart1_pin_mux();
#endif /* CONFIG_SERIAL2 */
#ifdef CONFIG_SERIAL3
enable_uart2_pin_mux();
#endif /* CONFIG_SERIAL3 */
#ifdef CONFIG_SERIAL4
enable_uart3_pin_mux();
#endif /* CONFIG_SERIAL4 */
#ifdef CONFIG_SERIAL5
enable_uart4_pin_mux();
#endif /* CONFIG_SERIAL5 */
#ifdef CONFIG_SERIAL6
enable_uart5_pin_mux();
#endif /* CONFIG_SERIAL6 */
regVal = readl(&uart_base->uartsyscfg);
regVal |= UART_RESET;
writel(regVal, &uart_base->uartsyscfg);
while ((readl(&uart_base->uartsyssts) &
UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
;
/* Disable smart idle */
regVal = readl(&uart_base->uartsyscfg);
regVal |= UART_SMART_IDLE_EN;
writel(regVal, &uart_base->uartsyscfg);
gd = &gdata;
preloader_console_init();
/* Initalize the board header */
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
if (read_eeprom() < 0)
puts("Could not get board ID.\n");
enable_board_pin_mux(&header);
if (board_is_evm_sk()) {
/*
* EVM SK 1.2A and later use gpio0_7 to enable DDR3.
* This is safe enough to do on older revs.
*/
gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
gpio_direction_output(GPIO_DDR_VTT_EN, 1);
}
if (board_is_evm_sk() || board_is_bone_lt())
config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data);
else if (board_is_evm_15_or_later())
config_ddr(303, MT41J512M8RH125_IOCTRL_VALUE, &ddr3_evm_data,
&ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data);
else
config_ddr(266, MT47H128M16RT25E_IOCTRL_VALUE, &ddr2_data,
&ddr2_cmd_ctrl_data, &ddr2_emif_reg_data);
#endif
}
