void main_init( void )
{
int sts;
sts = get_reset_reason();
main_status = MAIN_STS_NO_SNS_ERR;
main_is_enter_stby_mode = 0;
bio_init();
clk_init();
uart_init();
dbg_wait();
#ifdef FEATURE_WDOG_TRIG
IWDG_Enable();
bio_led_ctrl( BIO_LED_IX_POWER, 0, 0, 0 );
#else // FEATURE_WDOG_TRIG
dbg_out( "\r\n**********==> Watchdog Disabled!!!!!\r\n" );
bio_led_ctrl( BIO_LED_IX_POWER, 500, 500, BIO_LED_ALWAYS_WINK );
#endif // FEATURE_WDOG_TRIG
dbg_out_pool_const( UART_DBG_MSG_ENTER3 );
dbg_out( "================== 0x%02X =================\r\n", sts );
dbg_out( "==== Welcome to %s Ver %d.%02X ====\r\n",
MAIN_TIT_STR, MAIN_VER_MAJ, MAIN_VER_MIN );
dbg_out( "===== i=%d, si=%d, li=%d, f=%d, d=%d =====\r\n",
sizeof( int ), sizeof( short int ),
sizeof( long int ),sizeof( float ),sizeof( double ) );
dbg_out( "===== %dMHz %s %s =====\r\n",
SystemCoreClock / 1000000, __DATE__, __TIME__ );
dbg_out_pool_const( UART_DBG_MSG_EQ_LINE );
dbg_wait();
view_reset_reason( sts );
eep_param_init();
IWDG_ReloadCounter();
u3_ctrl.sw_baud = 115200;
uart3_init();
sns_init();
adc_init();
zb_init();
encb_init();
fnd_init();
indc_init();
bio_set_fan_pwm_base_freq( eep_hw_info.fan_base_f );
cmd_rx_ptr = u1_ctrl.rx_bptr;
// set monitor timer
clk_set_timer( &monit_timer, MAIN_MONITOR_MS, MAIN_MONITOR_MS,
CLK_SIGS_MONITOR );
} // end of main_init()
/**
* Internal function to initialize SoC reset reason at system initialization
*/
static void __esp_reset_reason_init(int init)
{
const uint32_t hw_reset = esp_rtc_get_reset_reason();
#if CONFIG_RESET_REASON_CHECK_WAKEUP
const uint32_t hw_wakeup = esp_rtc_get_wakeup_reason();
#else
const uint32_t hw_wakeup = 0;
#endif
const uint32_t hint = esp_reset_reason_get_hint(hw_reset);
s_reset_reason = get_reset_reason(hw_reset, hint);
if (init && hint != ESP_RST_UNKNOWN) {
esp_reset_reason_clear_hint();
}
if (init)
ESP_LOGI(TAG, "RTC reset %u wakeup %u store %u, reason is %u", hw_reset, hw_wakeup, hint, s_reset_reason);
}
static void ther_device_init(struct ther_info *ti)
{
/*
* 1. gpio init
*/
ther_port_init();
/*
* 2. uart init
*/
ther_uart_init(UART_PORT_0, UART_BAUD_RATE_115200, ther_at_handle);
print(LOG_INFO, "\n");
print(LOG_INFO, "-------------------------------------\n");
print(LOG_INFO, " Firmware V%d.%d\n",
FIRMWARE_MAJOR_VERSION, FIREWARM_MINOR_VERSION);
print(LOG_INFO, " %s, %s\n",
__DATE__, __TIME__);
print(LOG_INFO, " by <%s>\n", get_reset_reason());
uart_delay(UART_WAIT);
print(LOG_INFO, "\n");
print(LOG_INFO, " Copyright (c) 2015 [email protected]\r\n");
print(LOG_INFO, " All rights reserved.\r\n");
print(LOG_INFO, "-------------------------------------\r\n");
/*
* 2. buzzer init
*/
ther_buzzer_init(ti->task_id);
/*
* 3. button init
*/
ther_button_init(ti->task_id);
/*
* 4. oled display init
*/
oled_display_init(ti->task_id, ther_display_event_report);
/*
* 5. mtd
*/
ther_mtd_init();
/*
* 6. storage
*/
ther_storage_init();
/*
* 7. temp init
*/
ther_temp_init();
/* read high temp warning thershold */
if (!storage_read_high_temp_enabled(&ti->warning_enabled)) {
print(LOG_INFO, MODULE "read high temp enalbe failed, set enabled\n");
ti->warning_enabled = TRUE;
storage_write_high_temp_enabled(ti->warning_enabled);
}
if (!storage_read_high_temp_threshold(&ti->high_temp_threshold)) {
ti->high_temp_threshold = DEFAULT_HIGH_TEMP_THRESHOLD;
print(LOG_INFO, MODULE "read high temp threshold failed, set as %d\n", ti->high_temp_threshold);
storage_write_high_temp_threshold(ti->high_temp_threshold);
}
ti->next_warning_threshold = ti->high_temp_threshold;
/*
* 8. ble init
*/
ther_ble_init(ti->task_id, ther_handle_ts_event, ther_handle_ps_event, ther_handle_wechat_event);
// HCI_EXT_ClkDivOnHaltCmd( HCI_EXT_ENABLE_CLK_DIVIDE_ON_HALT );
// Enable stack to toggle bypass control on TPS62730 (DC/DC converter)
// HCI_EXT_MapPmIoPortCmd( HCI_EXT_PM_IO_PORT_NONE, HCI_EXT_PM_IO_PORT_PIN0 );
//the TI interface to set TXPOWER is not satisfying, so I have to
//set register TXPOWER myself.
// HCI_EXT_SetTxPowerCmd(LL_EXT_TX_POWER_0_DBM);
}