void FXAS21002C::measure() { /* status register and data as read back from the device */ #pragma pack(push, 1) struct { uint8_t cmd; uint8_t status; int16_t x; int16_t y; int16_t z; } raw_gyro_report; #pragma pack(pop) struct gyro_report gyro_report; /* start the performance counter */ perf_begin(_sample_perf); check_registers(); if (_register_wait != 0) { // we are waiting for some good transfers before using // the sensor again. _register_wait--; perf_end(_sample_perf); return; } /* fetch data from the sensor */ memset(&raw_gyro_report, 0, sizeof(raw_gyro_report)); raw_gyro_report.cmd = DIR_READ(FXAS21002C_STATUS); transfer((uint8_t *)&raw_gyro_report, (uint8_t *)&raw_gyro_report, sizeof(raw_gyro_report)); if (!(raw_gyro_report.status & DR_STATUS_ZYXDR)) { perf_end(_sample_perf); perf_count(_duplicates); return; } /* * The TEMP register contains an 8-bit 2's complement temperature value with a range * of –128 °C to +127 °C and a scaling of 1 °C/LSB. The temperature data is only * compensated (factory trim values applied) when the device is operating in the Active * mode and actively measuring the angular rate. */ if ((_read % _current_rate) == 0) { _last_temperature = read_reg(FXAS21002C_TEMP) * 1.0f; gyro_report.temperature = _last_temperature; } /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ gyro_report.timestamp = hrt_absolute_time(); // report the error count as the number of bad // register reads. This allows the higher level // code to decide if it should use this sensor based on // whether it has had failures gyro_report.error_count = perf_event_count(_bad_registers); gyro_report.x_raw = swap16(raw_gyro_report.x); gyro_report.y_raw = swap16(raw_gyro_report.y); gyro_report.z_raw = swap16(raw_gyro_report.z); float xraw_f = gyro_report.x_raw; float yraw_f = gyro_report.y_raw; float zraw_f = gyro_report.z_raw; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_in_new = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float y_in_new = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float z_in_new = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; gyro_report.x = _gyro_filter_x.apply(x_in_new); gyro_report.y = _gyro_filter_y.apply(y_in_new); gyro_report.z = _gyro_filter_z.apply(z_in_new); matrix::Vector3f gval(x_in_new, y_in_new, z_in_new); matrix::Vector3f gval_integrated; bool gyro_notify = _gyro_int.put(gyro_report.timestamp, gval, gval_integrated, gyro_report.integral_dt); gyro_report.x_integral = gval_integrated(0); gyro_report.y_integral = gval_integrated(1); gyro_report.z_integral = gval_integrated(2); gyro_report.scaling = _gyro_range_scale; /* return device ID */ gyro_report.device_id = _device_id.devid; _reports->force(&gyro_report); /* notify anyone waiting for data */ if (gyro_notify) { poll_notify(POLLIN); if (!(_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro_topic, &gyro_report); } } _read++; /* stop the perf counter */ perf_end(_sample_perf); }
void MPU9250::measure() { if (hrt_absolute_time() < _reset_wait) { // we're waiting for a reset to complete return; } struct MPUReport mpu_report; struct Report { int16_t accel_x; int16_t accel_y; int16_t accel_z; int16_t temp; int16_t gyro_x; int16_t gyro_y; int16_t gyro_z; } report; /* start measuring */ perf_begin(_sample_perf); /* * Fetch the full set of measurements from the MPU9250 in one pass. */ if (OK != _interface->read(MPU9250_SET_SPEED(MPUREG_INT_STATUS, MPU9250_HIGH_BUS_SPEED), (uint8_t *)&mpu_report, sizeof(mpu_report))) { return; } check_registers(); if (check_duplicate(&mpu_report.accel_x[0])) { return; } #ifdef USE_I2C if (_mag->is_passthrough()) { #endif _mag->_measure(mpu_report.mag); #ifdef USE_I2C } else { _mag->measure(); } #endif /* * Convert from big to little endian */ report.accel_x = int16_t_from_bytes(mpu_report.accel_x); report.accel_y = int16_t_from_bytes(mpu_report.accel_y); report.accel_z = int16_t_from_bytes(mpu_report.accel_z); report.temp = int16_t_from_bytes(mpu_report.temp); report.gyro_x = int16_t_from_bytes(mpu_report.gyro_x); report.gyro_y = int16_t_from_bytes(mpu_report.gyro_y); report.gyro_z = int16_t_from_bytes(mpu_report.gyro_z); if (check_null_data((uint32_t *)&report, sizeof(report) / 4)) { return; } if (_register_wait != 0) { // we are waiting for some good transfers before using the sensor again // We still increment _good_transfers, but don't return any data yet _register_wait--; return; } /* * Swap axes and negate y */ int16_t accel_xt = report.accel_y; int16_t accel_yt = ((report.accel_x == -32768) ? 32767 : -report.accel_x); int16_t gyro_xt = report.gyro_y; int16_t gyro_yt = ((report.gyro_x == -32768) ? 32767 : -report.gyro_x); /* * Apply the swap */ report.accel_x = accel_xt; report.accel_y = accel_yt; report.gyro_x = gyro_xt; report.gyro_y = gyro_yt; /* * Report buffers. */ accel_report arb; gyro_report grb; /* * Adjust and scale results to m/s^2. */ grb.timestamp = arb.timestamp = hrt_absolute_time(); // report the error count as the sum of the number of bad // transfers and bad register reads. This allows the higher // level code to decide if it should use this sensor based on // whether it has had failures grb.error_count = arb.error_count = perf_event_count(_bad_transfers) + perf_event_count(_bad_registers); /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ /* NOTE: Axes have been swapped to match the board a few lines above. */ arb.x_raw = report.accel_x; arb.y_raw = report.accel_y; arb.z_raw = report.accel_z; float xraw_f = report.accel_x; float yraw_f = report.accel_y; float zraw_f = report.accel_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_in_new = ((xraw_f * _accel_range_scale) - _accel_scale.x_offset) * _accel_scale.x_scale; float y_in_new = ((yraw_f * _accel_range_scale) - _accel_scale.y_offset) * _accel_scale.y_scale; float z_in_new = ((zraw_f * _accel_range_scale) - _accel_scale.z_offset) * _accel_scale.z_scale; arb.x = _accel_filter_x.apply(x_in_new); arb.y = _accel_filter_y.apply(y_in_new); arb.z = _accel_filter_z.apply(z_in_new); math::Vector<3> aval(x_in_new, y_in_new, z_in_new); math::Vector<3> aval_integrated; bool accel_notify = _accel_int.put(arb.timestamp, aval, aval_integrated, arb.integral_dt); arb.x_integral = aval_integrated(0); arb.y_integral = aval_integrated(1); arb.z_integral = aval_integrated(2); arb.scaling = _accel_range_scale; arb.range_m_s2 = _accel_range_m_s2; _last_temperature = (report.temp) / 361.0f + 35.0f; arb.temperature_raw = report.temp; arb.temperature = _last_temperature; grb.x_raw = report.gyro_x; grb.y_raw = report.gyro_y; grb.z_raw = report.gyro_z; xraw_f = report.gyro_x; yraw_f = report.gyro_y; zraw_f = report.gyro_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_gyro_in_new = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float y_gyro_in_new = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float z_gyro_in_new = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; grb.x = _gyro_filter_x.apply(x_gyro_in_new); grb.y = _gyro_filter_y.apply(y_gyro_in_new); grb.z = _gyro_filter_z.apply(z_gyro_in_new); math::Vector<3> gval(x_gyro_in_new, y_gyro_in_new, z_gyro_in_new); math::Vector<3> gval_integrated; bool gyro_notify = _gyro_int.put(arb.timestamp, gval, gval_integrated, grb.integral_dt); grb.x_integral = gval_integrated(0); grb.y_integral = gval_integrated(1); grb.z_integral = gval_integrated(2); grb.scaling = _gyro_range_scale; grb.range_rad_s = _gyro_range_rad_s; grb.temperature_raw = report.temp; grb.temperature = _last_temperature; _accel_reports->force(&arb); _gyro_reports->force(&grb); /* notify anyone waiting for data */ if (accel_notify) { poll_notify(POLLIN); } if (gyro_notify) { _gyro->parent_poll_notify(); } if (accel_notify && !(_pub_blocked)) { /* log the time of this report */ perf_begin(_controller_latency_perf); /* publish it */ orb_publish(ORB_ID(sensor_accel), _accel_topic, &arb); } if (gyro_notify && !(_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro->_gyro_topic, &grb); } /* stop measuring */ perf_end(_sample_perf); }
void L3GD20::measure() { /* status register and data as read back from the device */ #pragma pack(push, 1) struct { uint8_t cmd; int8_t temp; uint8_t status; int16_t x; int16_t y; int16_t z; } raw_report; #pragma pack(pop) gyro_report report; /* start the performance counter */ perf_begin(_sample_perf); check_registers(); /* fetch data from the sensor */ memset(&raw_report, 0, sizeof(raw_report)); raw_report.cmd = ADDR_OUT_TEMP | DIR_READ | ADDR_INCREMENT; transfer((uint8_t *)&raw_report, (uint8_t *)&raw_report, sizeof(raw_report)); if (!(raw_report.status & STATUS_ZYXDA)) { perf_end(_sample_perf); perf_count(_duplicates); return; } /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ report.timestamp = hrt_absolute_time(); report.error_count = perf_event_count(_bad_registers); switch (_orientation) { case SENSOR_BOARD_ROTATION_000_DEG: /* keep axes in place */ report.x_raw = raw_report.x; report.y_raw = raw_report.y; break; case SENSOR_BOARD_ROTATION_090_DEG: /* swap x and y */ report.x_raw = raw_report.y; report.y_raw = raw_report.x; break; case SENSOR_BOARD_ROTATION_180_DEG: /* swap x and y and negate both */ report.x_raw = ((raw_report.x == -32768) ? 32767 : -raw_report.x); report.y_raw = ((raw_report.y == -32768) ? 32767 : -raw_report.y); break; case SENSOR_BOARD_ROTATION_270_DEG: /* swap x and y and negate y */ report.x_raw = raw_report.y; report.y_raw = ((raw_report.x == -32768) ? 32767 : -raw_report.x); break; } report.z_raw = raw_report.z; #if defined(CONFIG_ARCH_BOARD_MINDPX_V2) int16_t tx = -report.y_raw; int16_t ty = -report.x_raw; int16_t tz = -report.z_raw; report.x_raw = tx; report.y_raw = ty; report.z_raw = tz; #endif report.temperature_raw = raw_report.temp; float xraw_f = report.x_raw; float yraw_f = report.y_raw; float zraw_f = report.z_raw; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float xin = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float yin = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float zin = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; report.x = _gyro_filter_x.apply(xin); report.y = _gyro_filter_y.apply(yin); report.z = _gyro_filter_z.apply(zin); math::Vector<3> gval(xin, yin, zin); math::Vector<3> gval_integrated; bool gyro_notify = _gyro_int.put(report.timestamp, gval, gval_integrated, report.integral_dt); report.x_integral = gval_integrated(0); report.y_integral = gval_integrated(1); report.z_integral = gval_integrated(2); report.temperature = L3GD20_TEMP_OFFSET_CELSIUS - raw_report.temp; report.scaling = _gyro_range_scale; report.range_rad_s = _gyro_range_rad_s; _reports->force(&report); if (gyro_notify) { /* notify anyone waiting for data */ poll_notify(POLLIN); /* publish for subscribers */ if (!(_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro_topic, &report); } } _read++; /* stop the perf counter */ perf_end(_sample_perf); }
void BMI160::measure() { if (hrt_absolute_time() < _reset_wait) { // we're waiting for a reset to complete return; } struct BMIReport bmi_report; struct Report { int16_t accel_x; int16_t accel_y; int16_t accel_z; int16_t temp; int16_t gyro_x; int16_t gyro_y; int16_t gyro_z; } report; /* start measuring */ perf_begin(_sample_perf); /* * Fetch the full set of measurements from the BMI160 in one pass. */ bmi_report.cmd = BMIREG_GYR_X_L | DIR_READ; uint8_t status = read_reg(BMIREG_STATUS); if (OK != transfer((uint8_t *)&bmi_report, ((uint8_t *)&bmi_report), sizeof(bmi_report))) { return; } check_registers(); if ((!(status & (0x80))) && (!(status & (0x04)))) { perf_end(_sample_perf); perf_count(_duplicates); _got_duplicate = true; return; } _last_accel[0] = bmi_report.accel_x; _last_accel[1] = bmi_report.accel_y; _last_accel[2] = bmi_report.accel_z; _got_duplicate = false; uint8_t temp_l = read_reg(BMIREG_TEMP_0); uint8_t temp_h = read_reg(BMIREG_TEMP_1); report.temp = ((temp_h << 8) + temp_l); report.accel_x = bmi_report.accel_x; report.accel_y = bmi_report.accel_y; report.accel_z = bmi_report.accel_z; report.gyro_x = bmi_report.gyro_x; report.gyro_y = bmi_report.gyro_y; report.gyro_z = bmi_report.gyro_z; if (report.accel_x == 0 && report.accel_y == 0 && report.accel_z == 0 && report.temp == 0 && report.gyro_x == 0 && report.gyro_y == 0 && report.gyro_z == 0) { // all zero data - probably a SPI bus error perf_count(_bad_transfers); perf_end(_sample_perf); // note that we don't call reset() here as a reset() // costs 20ms with interrupts disabled. That means if // the bmi160 does go bad it would cause a FMU failure, // regardless of whether another sensor is available, return; } perf_count(_good_transfers); if (_register_wait != 0) { // we are waiting for some good transfers before using // the sensor again. We still increment // _good_transfers, but don't return any data yet _register_wait--; return; } /* * Report buffers. */ accel_report arb; gyro_report grb; /* * Adjust and scale results to m/s^2. */ grb.timestamp = arb.timestamp = hrt_absolute_time(); // report the error count as the sum of the number of bad // transfers and bad register reads. This allows the higher // level code to decide if it should use this sensor based on // whether it has had failures grb.error_count = arb.error_count = perf_event_count(_bad_transfers) + perf_event_count(_bad_registers); /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ /* NOTE: Axes have been swapped to match the board a few lines above. */ arb.x_raw = report.accel_x; arb.y_raw = report.accel_y; arb.z_raw = report.accel_z; float xraw_f = report.accel_x; float yraw_f = report.accel_y; float zraw_f = report.accel_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_in_new = ((xraw_f * _accel_range_scale) - _accel_scale.x_offset) * _accel_scale.x_scale; float y_in_new = ((yraw_f * _accel_range_scale) - _accel_scale.y_offset) * _accel_scale.y_scale; float z_in_new = ((zraw_f * _accel_range_scale) - _accel_scale.z_offset) * _accel_scale.z_scale; arb.x = _accel_filter_x.apply(x_in_new); arb.y = _accel_filter_y.apply(y_in_new); arb.z = _accel_filter_z.apply(z_in_new); math::Vector<3> aval(x_in_new, y_in_new, z_in_new); math::Vector<3> aval_integrated; bool accel_notify = _accel_int.put(arb.timestamp, aval, aval_integrated, arb.integral_dt); arb.x_integral = aval_integrated(0); arb.y_integral = aval_integrated(1); arb.z_integral = aval_integrated(2); arb.scaling = _accel_range_scale; arb.range_m_s2 = _accel_range_m_s2; _last_temperature = 23 + report.temp * 1.0f / 512.0f; arb.temperature_raw = report.temp; arb.temperature = _last_temperature; /* return device ID */ arb.device_id = _device_id.devid; grb.x_raw = report.gyro_x; grb.y_raw = report.gyro_y; grb.z_raw = report.gyro_z; xraw_f = report.gyro_x; yraw_f = report.gyro_y; zraw_f = report.gyro_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_gyro_in_new = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float y_gyro_in_new = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float z_gyro_in_new = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; grb.x = _gyro_filter_x.apply(x_gyro_in_new); grb.y = _gyro_filter_y.apply(y_gyro_in_new); grb.z = _gyro_filter_z.apply(z_gyro_in_new); math::Vector<3> gval(x_gyro_in_new, y_gyro_in_new, z_gyro_in_new); math::Vector<3> gval_integrated; bool gyro_notify = _gyro_int.put(arb.timestamp, gval, gval_integrated, grb.integral_dt); grb.x_integral = gval_integrated(0); grb.y_integral = gval_integrated(1); grb.z_integral = gval_integrated(2); grb.scaling = _gyro_range_scale; grb.range_rad_s = _gyro_range_rad_s; grb.temperature_raw = report.temp; grb.temperature = _last_temperature; /* return device ID */ grb.device_id = _gyro->_device_id.devid; _accel_reports->force(&arb); _gyro_reports->force(&grb); /* notify anyone waiting for data */ if (accel_notify) { poll_notify(POLLIN); } if (gyro_notify) { _gyro->parent_poll_notify(); } if (accel_notify && !(_pub_blocked)) { /* log the time of this report */ perf_begin(_controller_latency_perf); /* publish it */ orb_publish(ORB_ID(sensor_accel), _accel_topic, &arb); } if (gyro_notify && !(_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro->_gyro_topic, &grb); } /* stop measuring */ perf_end(_sample_perf); }
void BMI055_gyro::measure() { if (hrt_absolute_time() < _reset_wait) { // we're waiting for a reset to complete return; } struct BMI_GyroReport bmi_gyroreport; struct Report { int16_t temp; int16_t gyro_x; int16_t gyro_y; int16_t gyro_z; } report; /* start measuring */ perf_begin(_sample_perf); /* * Fetch the full set of measurements from the BMI055 gyro in one pass. */ bmi_gyroreport.cmd = BMI055_GYR_X_L | DIR_READ; if (OK != transfer((uint8_t *)&bmi_gyroreport, ((uint8_t *)&bmi_gyroreport), sizeof(bmi_gyroreport))) { return; } check_registers(); uint8_t temp = read_reg(BMI055_ACC_TEMP); report.temp = temp; report.gyro_x = bmi_gyroreport.gyro_x; report.gyro_y = bmi_gyroreport.gyro_y; report.gyro_z = bmi_gyroreport.gyro_z; if (report.temp == 0 && report.gyro_x == 0 && report.gyro_y == 0 && report.gyro_z == 0) { // all zero data - probably a SPI bus error perf_count(_bad_transfers); perf_end(_sample_perf); // note that we don't call reset() here as a reset() // costs 20ms with interrupts disabled. That means if // the bmi055 does go bad it would cause a FMU failure, // regardless of whether another sensor is available, return; } perf_count(_good_transfers); if (_register_wait != 0) { // we are waiting for some good transfers before using // the sensor again. We still increment // _good_transfers, but don't return any data yet _register_wait--; return; } /* * Report buffers. */ gyro_report grb; grb.timestamp = hrt_absolute_time(); // report the error count as the sum of the number of bad // transfers and bad register reads. This allows the higher // level code to decide if it should use this sensor based on // whether it has had failures grb.error_count = perf_event_count(_bad_transfers) + perf_event_count(_bad_registers); /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ grb.x_raw = report.gyro_x; grb.y_raw = report.gyro_y; grb.z_raw = report.gyro_z; float xraw_f = report.gyro_x; float yraw_f = report.gyro_y; float zraw_f = report.gyro_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_gyro_in_new = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float y_gyro_in_new = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float z_gyro_in_new = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; grb.x = _gyro_filter_x.apply(x_gyro_in_new); grb.y = _gyro_filter_y.apply(y_gyro_in_new); grb.z = _gyro_filter_z.apply(z_gyro_in_new); matrix::Vector3f gval(x_gyro_in_new, y_gyro_in_new, z_gyro_in_new); matrix::Vector3f gval_integrated; bool gyro_notify = _gyro_int.put(grb.timestamp, gval, gval_integrated, grb.integral_dt); grb.x_integral = gval_integrated(0); grb.y_integral = gval_integrated(1); grb.z_integral = gval_integrated(2); grb.scaling = _gyro_range_scale; grb.range_rad_s = _gyro_range_rad_s; grb.temperature_raw = report.temp; grb.temperature = _last_temperature; grb.device_id = _device_id.devid; _gyro_reports->force(&grb); /* notify anyone waiting for data */ if (gyro_notify) { poll_notify(POLLIN); } if (gyro_notify && !(_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro_topic, &grb); } /* stop measuring */ perf_end(_sample_perf); }
void MPU9250::measure() { if (hrt_absolute_time() < _reset_wait) { // we're waiting for a reset to complete return; } struct MPUReport mpu_report; struct ICMReport icm_report; struct Report { int16_t accel_x; int16_t accel_y; int16_t accel_z; int16_t temp; int16_t gyro_x; int16_t gyro_y; int16_t gyro_z; } report; /* start measuring */ perf_begin(_sample_perf); /* * Fetch the full set of measurements from the MPU9250 in one pass */ if ((!_magnetometer_only || _mag->is_passthrough()) && _register_wait == 0) { if (_whoami == MPU_WHOAMI_9250 || _whoami == MPU_WHOAMI_6500) { if (OK != read_reg_range(MPUREG_INT_STATUS, MPU9250_HIGH_BUS_SPEED, (uint8_t *)&mpu_report, sizeof(mpu_report))) { perf_end(_sample_perf); return; } } else { // ICM20948 select_register_bank(REG_BANK(ICMREG_20948_ACCEL_XOUT_H)); if (OK != read_reg_range(ICMREG_20948_ACCEL_XOUT_H, MPU9250_HIGH_BUS_SPEED, (uint8_t *)&icm_report, sizeof(icm_report))) { perf_end(_sample_perf); return; } } check_registers(); if (check_duplicate(MPU_OR_ICM(&mpu_report.accel_x[0], &icm_report.accel_x[0]))) { return; } } /* * In case of a mag passthrough read, hand the magnetometer data over to _mag. Else, * try to read a magnetometer report. */ # ifdef USE_I2C if (_mag->is_passthrough()) { # endif _mag->_measure(mpu_report.mag); # ifdef USE_I2C } else { _mag->measure(); } # endif /* * Continue evaluating gyro and accelerometer results */ if (!_magnetometer_only && _register_wait == 0) { /* * Convert from big to little endian */ if (_whoami == ICM_WHOAMI_20948) { report.accel_x = int16_t_from_bytes(icm_report.accel_x); report.accel_y = int16_t_from_bytes(icm_report.accel_y); report.accel_z = int16_t_from_bytes(icm_report.accel_z); report.temp = int16_t_from_bytes(icm_report.temp); report.gyro_x = int16_t_from_bytes(icm_report.gyro_x); report.gyro_y = int16_t_from_bytes(icm_report.gyro_y); report.gyro_z = int16_t_from_bytes(icm_report.gyro_z); } else { // MPU9250/MPU6500 report.accel_x = int16_t_from_bytes(mpu_report.accel_x); report.accel_y = int16_t_from_bytes(mpu_report.accel_y); report.accel_z = int16_t_from_bytes(mpu_report.accel_z); report.temp = int16_t_from_bytes(mpu_report.temp); report.gyro_x = int16_t_from_bytes(mpu_report.gyro_x); report.gyro_y = int16_t_from_bytes(mpu_report.gyro_y); report.gyro_z = int16_t_from_bytes(mpu_report.gyro_z); } if (check_null_data((uint16_t *)&report, sizeof(report) / 2)) { return; } } if (_register_wait != 0) { /* * We are waiting for some good transfers before using the sensor again. * We still increment _good_transfers, but don't return any data yet. * */ _register_wait--; return; } /* * Get sensor temperature */ _last_temperature = (report.temp) / 333.87f + 21.0f; /* * Convert and publish accelerometer and gyrometer data. */ if (!_magnetometer_only) { /* * Keeping the axes as they are for ICM20948 so orientation will match the actual chip orientation */ if (_whoami != ICM_WHOAMI_20948) { /* * Swap axes and negate y */ int16_t accel_xt = report.accel_y; int16_t accel_yt = ((report.accel_x == -32768) ? 32767 : -report.accel_x); int16_t gyro_xt = report.gyro_y; int16_t gyro_yt = ((report.gyro_x == -32768) ? 32767 : -report.gyro_x); /* * Apply the swap */ report.accel_x = accel_xt; report.accel_y = accel_yt; report.gyro_x = gyro_xt; report.gyro_y = gyro_yt; } /* * Report buffers. */ sensor_accel_s arb; sensor_gyro_s grb; /* * Adjust and scale results to m/s^2. */ grb.timestamp = arb.timestamp = hrt_absolute_time(); // report the error count as the sum of the number of bad // transfers and bad register reads. This allows the higher // level code to decide if it should use this sensor based on // whether it has had failures grb.error_count = arb.error_count = perf_event_count(_bad_transfers) + perf_event_count(_bad_registers); /* * 1) Scale raw value to SI units using scaling from datasheet. * 2) Subtract static offset (in SI units) * 3) Scale the statically calibrated values with a linear * dynamically obtained factor * * Note: the static sensor offset is the number the sensor outputs * at a nominally 'zero' input. Therefore the offset has to * be subtracted. * * Example: A gyro outputs a value of 74 at zero angular rate * the offset is 74 from the origin and subtracting * 74 from all measurements centers them around zero. */ /* NOTE: Axes have been swapped to match the board a few lines above. */ arb.x_raw = report.accel_x; arb.y_raw = report.accel_y; arb.z_raw = report.accel_z; float xraw_f = report.accel_x; float yraw_f = report.accel_y; float zraw_f = report.accel_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_in_new = ((xraw_f * _accel_range_scale) - _accel_scale.x_offset) * _accel_scale.x_scale; float y_in_new = ((yraw_f * _accel_range_scale) - _accel_scale.y_offset) * _accel_scale.y_scale; float z_in_new = ((zraw_f * _accel_range_scale) - _accel_scale.z_offset) * _accel_scale.z_scale; arb.x = _accel_filter_x.apply(x_in_new); arb.y = _accel_filter_y.apply(y_in_new); arb.z = _accel_filter_z.apply(z_in_new); matrix::Vector3f aval(x_in_new, y_in_new, z_in_new); matrix::Vector3f aval_integrated; bool accel_notify = _accel_int.put(arb.timestamp, aval, aval_integrated, arb.integral_dt); arb.x_integral = aval_integrated(0); arb.y_integral = aval_integrated(1); arb.z_integral = aval_integrated(2); arb.scaling = _accel_range_scale; arb.temperature = _last_temperature; /* return device ID */ arb.device_id = _accel->_device_id.devid; grb.x_raw = report.gyro_x; grb.y_raw = report.gyro_y; grb.z_raw = report.gyro_z; xraw_f = report.gyro_x; yraw_f = report.gyro_y; zraw_f = report.gyro_z; // apply user specified rotation rotate_3f(_rotation, xraw_f, yraw_f, zraw_f); float x_gyro_in_new = ((xraw_f * _gyro_range_scale) - _gyro_scale.x_offset) * _gyro_scale.x_scale; float y_gyro_in_new = ((yraw_f * _gyro_range_scale) - _gyro_scale.y_offset) * _gyro_scale.y_scale; float z_gyro_in_new = ((zraw_f * _gyro_range_scale) - _gyro_scale.z_offset) * _gyro_scale.z_scale; grb.x = _gyro_filter_x.apply(x_gyro_in_new); grb.y = _gyro_filter_y.apply(y_gyro_in_new); grb.z = _gyro_filter_z.apply(z_gyro_in_new); matrix::Vector3f gval(x_gyro_in_new, y_gyro_in_new, z_gyro_in_new); matrix::Vector3f gval_integrated; bool gyro_notify = _gyro_int.put(arb.timestamp, gval, gval_integrated, grb.integral_dt); grb.x_integral = gval_integrated(0); grb.y_integral = gval_integrated(1); grb.z_integral = gval_integrated(2); grb.scaling = _gyro_range_scale; grb.temperature = _last_temperature; /* return device ID */ grb.device_id = _gyro->_device_id.devid; _accel_reports->force(&arb); _gyro_reports->force(&grb); /* notify anyone waiting for data */ if (accel_notify) { _accel->poll_notify(POLLIN); } if (gyro_notify) { _gyro->parent_poll_notify(); } if (accel_notify && !(_accel->_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_accel), _accel_topic, &arb); } if (gyro_notify && !(_gyro->_pub_blocked)) { /* publish it */ orb_publish(ORB_ID(sensor_gyro), _gyro->_gyro_topic, &grb); } } /* stop measuring */ perf_end(_sample_perf); }