static int __devinit avma1cs_config(struct pcmcia_device *link)
{
int i = -1;
char devname[128];
IsdnCard_t icard;
int busy = 0;
dev_dbg(&link->dev, "avma1cs_config(0x%p)\n", link);
devname[0] = 0;
if (link->prod_id[1])
strlcpy(devname, link->prod_id[1], sizeof(devname));
if (pcmcia_loop_config(link, avma1cs_configcheck, NULL))
return -ENODEV;
do {
/*
* allocate an interrupt line
*/
if (!link->irq) {
/* undo */
pcmcia_disable_device(link);
break;
}
/*
* configure the PCMCIA socket
*/
i = pcmcia_enable_device(link);
if (i != 0) {
pcmcia_disable_device(link);
break;
}
} while (0);
/* If any step failed, release any partially configured state */
if (i != 0) {
avma1cs_release(link);
return -ENODEV;
}
icard.para[0] = link->irq;
icard.para[1] = link->resource[0]->start;
icard.protocol = isdnprot;
icard.typ = ISDN_CTYPE_A1_PCMCIA;
i = hisax_init_pcmcia(link, &busy, &icard);
if (i < 0) {
printk(KERN_ERR "avma1_cs: failed to initialize AVM A1 "
"PCMCIA %d at i/o %#x\n", i,
(unsigned int) link->resource[0]->start);
avma1cs_release(link);
return -ENODEV;
}
link->priv = (void *) (unsigned long) i;
return 0;
} /* avma1cs_config */
static int __devinit teles_cs_config(struct pcmcia_device *link)
{
local_info_t *dev;
int i;
IsdnCard_t icard;
dev_dbg(&link->dev, "teles_config(0x%p)\n", link);
dev = link->priv;
i = pcmcia_loop_config(link, teles_cs_configcheck, NULL);
if (i != 0)
goto cs_failed;
if (!link->irq)
goto cs_failed;
i = pcmcia_request_configuration(link, &link->conf);
if (i != 0)
goto cs_failed;
/* Finally, report what we've done */
dev_info(&link->dev, "index 0x%02x:",
link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
printk("\n");
icard.para[0] = link->irq;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_TELESPCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "teles_cs: failed to initialize Teles PCMCIA %d at i/o %#x\n",
i, link->io.BasePort1);
teles_cs_release(link);
return -ENODEV;
}
((local_info_t*)link->priv)->cardnr = i;
return 0;
cs_failed:
teles_cs_release(link);
return -ENODEV;
} /* teles_cs_config */
static int __devinit sedlbauer_config(struct pcmcia_device *link)
{
int ret;
IsdnCard_t icard;
dev_dbg(&link->dev, "sedlbauer_config(0x%p)\n", link);
link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_CHECK_VCC |
CONF_AUTO_SET_VPP | CONF_AUTO_AUDIO | CONF_AUTO_SET_IO;
ret = pcmcia_loop_config(link, sedlbauer_config_check, NULL);
if (ret)
goto failed;
ret = pcmcia_enable_device(link);
if (ret)
goto failed;
icard.para[0] = link->irq;
icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_SEDLBAUER_PCMCIA;
ret = hisax_init_pcmcia(link,
&(((local_info_t *)link->priv)->stop), &icard);
if (ret < 0) {
printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d with %pR\n",
ret, link->resource[0]);
sedlbauer_release(link);
return -ENODEV;
} else
((local_info_t *)link->priv)->cardnr = ret;
return 0;
failed:
sedlbauer_release(link);
return -ENODEV;
} /* sedlbauer_config */
static int elsa_cs_config(struct pcmcia_device *link)
{
int i;
IsdnCard_t icard;
dev_dbg(&link->dev, "elsa_config(0x%p)\n", link);
link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
i = pcmcia_loop_config(link, elsa_cs_configcheck, NULL);
if (i != 0)
goto failed;
if (!link->irq)
goto failed;
i = pcmcia_enable_device(link);
if (i != 0)
goto failed;
icard.para[0] = link->irq;
icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_ELSA_PCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t *)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "elsa_cs: failed to initialize Elsa "
"PCMCIA %d with %pR\n", i, link->resource[0]);
elsa_cs_release(link);
} else
((local_info_t *)link->priv)->cardnr = i;
return 0;
failed:
elsa_cs_release(link);
return -ENODEV;
} /* elsa_cs_config */
static int __devinit teles_cs_config(struct pcmcia_device *link)
{
int i;
IsdnCard_t icard;
dev_dbg(&link->dev, "teles_config(0x%p)\n", link);
i = pcmcia_loop_config(link, teles_cs_configcheck, NULL);
if (i != 0)
goto cs_failed;
if (!link->irq)
goto cs_failed;
i = pcmcia_enable_device(link);
if (i != 0)
goto cs_failed;
icard.para[0] = link->irq;
icard.para[1] = link->resource[0]->start;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_TELESPCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "teles_cs: failed to initialize Teles PCMCIA %d at i/o %#x\n",
i, (unsigned int) link->resource[0]->start);
teles_cs_release(link);
return -ENODEV;
}
((local_info_t*)link->priv)->cardnr = i;
return 0;
cs_failed:
teles_cs_release(link);
return -ENODEV;
} /* teles_cs_config */
static void elsa_cs_config(dev_link_t *link)
{
client_handle_t handle;
tuple_t tuple;
cisparse_t parse;
local_info_t *dev;
int i, j, last_fn;
u_short buf[128];
cistpl_cftable_entry_t *cf = &parse.cftable_entry;
IsdnCard_t icard;
DEBUG(0, "elsa_config(0x%p)\n", link);
handle = link->handle;
dev = link->priv;
/*
This reads the card's CONFIG tuple to find its configuration
registers.
*/
tuple.DesiredTuple = CISTPL_CONFIG;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleDataMax = 255;
tuple.TupleOffset = 0;
tuple.Attributes = 0;
i = first_tuple(handle, &tuple, &parse);
if (i != CS_SUCCESS) {
last_fn = ParseTuple;
goto cs_failed;
}
link->conf.ConfigBase = parse.config.base;
link->conf.Present = parse.config.rmask[0];
/* Configure card */
link->state |= DEV_CONFIG;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleOffset = 0; tuple.TupleDataMax = 255;
tuple.Attributes = 0;
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
i = first_tuple(handle, &tuple, &parse);
while (i == CS_SUCCESS) {
if ( (cf->io.nwin > 0) && cf->io.win[0].base) {
printk(KERN_INFO "(elsa_cs: looks like the 96 model)\n");
link->conf.ConfigIndex = cf->index;
link->io.BasePort1 = cf->io.win[0].base;
i = pcmcia_request_io(link->handle, &link->io);
if (i == CS_SUCCESS) break;
} else {
printk(KERN_INFO "(elsa_cs: looks like the 97 model)\n");
link->conf.ConfigIndex = cf->index;
for (i = 0, j = 0x2f0; j > 0x100; j -= 0x10) {
link->io.BasePort1 = j;
i = pcmcia_request_io(link->handle, &link->io);
if (i == CS_SUCCESS) break;
}
break;
}
i = next_tuple(handle, &tuple, &parse);
}
if (i != CS_SUCCESS) {
last_fn = RequestIO;
goto cs_failed;
}
i = pcmcia_request_irq(link->handle, &link->irq);
if (i != CS_SUCCESS) {
link->irq.AssignedIRQ = 0;
last_fn = RequestIRQ;
goto cs_failed;
}
i = pcmcia_request_configuration(link->handle, &link->conf);
if (i != CS_SUCCESS) {
last_fn = RequestConfiguration;
goto cs_failed;
}
/* At this point, the dev_node_t structure(s) should be
initialized and arranged in a linked list at link->dev. *//* */
sprintf(dev->node.dev_name, "elsa");
dev->node.major = dev->node.minor = 0x0;
link->dev = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x: Vcc %d.%d",
dev->node.dev_name, link->conf.ConfigIndex,
link->conf.Vcc/10, link->conf.Vcc%10);
if (link->conf.Vpp1)
printk(", Vpp %d.%d", link->conf.Vpp1/10, link->conf.Vpp1%10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
printk("\n");
link->state &= ~DEV_CONFIG_PENDING;
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_ELSA_PCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "elsa_cs: failed to initialize Elsa PCMCIA %d at i/o %#x\n",
i, link->io.BasePort1);
elsa_cs_release(link);
} else
((local_info_t*)link->priv)->cardnr = i;
return;
cs_failed:
cs_error(link->handle, last_fn, i);
elsa_cs_release(link);
} /* elsa_cs_config */
static int teles_cs_config(struct pcmcia_device *link)
{
local_info_t *dev;
int i, last_fn;
IsdnCard_t icard;
DEBUG(0, "teles_config(0x%p)\n", link);
dev = link->priv;
i = pcmcia_loop_config(link, teles_cs_configcheck, NULL);
if (i != 0) {
last_fn = RequestIO;
goto cs_failed;
}
i = pcmcia_request_irq(link, &link->irq);
if (i != 0) {
link->irq.AssignedIRQ = 0;
last_fn = RequestIRQ;
goto cs_failed;
}
i = pcmcia_request_configuration(link, &link->conf);
if (i != 0) {
last_fn = RequestConfiguration;
goto cs_failed;
}
/* At this point, the dev_node_t structure(s) should be
initialized and arranged in a linked list at link->dev. *//* */
sprintf(dev->node.dev_name, "teles");
dev->node.major = dev->node.minor = 0x0;
link->dev_node = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x:",
dev->node.dev_name, link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
printk("\n");
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_TELESPCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "teles_cs: failed to initialize Teles PCMCIA %d at i/o %#x\n",
i, link->io.BasePort1);
teles_cs_release(link);
return -ENODEV;
}
((local_info_t*)link->priv)->cardnr = i;
return 0;
cs_failed:
cs_error(link, last_fn, i);
teles_cs_release(link);
return -ENODEV;
} /* teles_cs_config */
static int sedlbauer_config(struct pcmcia_device *link)
{
local_info_t *dev = link->priv;
tuple_t tuple;
cisparse_t parse;
int last_fn, last_ret;
u8 buf[64];
config_info_t conf;
win_req_t req;
memreq_t map;
IsdnCard_t icard;
DEBUG(0, "sedlbauer_config(0x%p)\n", link);
/*
This reads the card's CONFIG tuple to find its configuration
registers.
*/
tuple.DesiredTuple = CISTPL_CONFIG;
tuple.Attributes = 0;
tuple.TupleData = buf;
tuple.TupleDataMax = sizeof(buf);
tuple.TupleOffset = 0;
CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
CS_CHECK(GetTupleData, pcmcia_get_tuple_data(link, &tuple));
CS_CHECK(ParseTuple, pcmcia_parse_tuple(link, &tuple, &parse));
link->conf.ConfigBase = parse.config.base;
link->conf.Present = parse.config.rmask[0];
CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(link, &conf));
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including
voltage, IO window, memory window, and interrupt settings.
We make no assumptions about the card to be configured: we use
just the information available in the CIS. In an ideal world,
this would work for any PCMCIA card, but it requires a complete
and accurate CIS. In practice, a driver usually "knows" most of
these things without consulting the CIS, and most client drivers
will only use the CIS to fill in implementation-defined details.
*/
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple));
while (1) {
cistpl_cftable_entry_t dflt = { 0 };
cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
if (pcmcia_get_tuple_data(link, &tuple) != 0 ||
pcmcia_parse_tuple(link, &tuple, &parse) != 0)
goto next_entry;
if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg;
if (cfg->index == 0) goto next_entry;
link->conf.ConfigIndex = cfg->index;
/* Does this card need audio output? */
if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
}
/* Use power settings for Vcc and Vpp if present */
/* Note that the CIS values need to be rescaled */
if (cfg->vcc.present & (1<<CISTPL_POWER_VNOM)) {
if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM]/10000)
goto next_entry;
} else if (dflt.vcc.present & (1<<CISTPL_POWER_VNOM)) {
if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM]/10000)
goto next_entry;
}
if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
link->conf.Vpp =
cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
else if (dflt.vpp1.present & (1<<CISTPL_POWER_VNOM))
link->conf.Vpp =
dflt.vpp1.param[CISTPL_POWER_VNOM]/10000;
/* Do we need to allocate an interrupt? */
if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
link->conf.Attributes |= CONF_ENABLE_IRQ;
/* IO window settings */
link->io.NumPorts1 = link->io.NumPorts2 = 0;
if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
if (!(io->flags & CISTPL_IO_8BIT))
link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
if (!(io->flags & CISTPL_IO_16BIT))
link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
/* new in dummy.cs 2001/01/28 MN
link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
*/
link->io.BasePort1 = io->win[0].base;
link->io.NumPorts1 = io->win[0].len;
if (io->nwin > 1) {
link->io.Attributes2 = link->io.Attributes1;
link->io.BasePort2 = io->win[1].base;
link->io.NumPorts2 = io->win[1].len;
}
/* This reserves IO space but doesn't actually enable it */
if (pcmcia_request_io(link, &link->io) != 0)
goto next_entry;
}
/*
Now set up a common memory window, if needed. There is room
in the struct pcmcia_device structure for one memory window handle,
but if the base addresses need to be saved, or if multiple
windows are needed, the info should go in the private data
structure for this device.
Note that the memory window base is a physical address, and
needs to be mapped to virtual space with ioremap() before it
is used.
*/
if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
cistpl_mem_t *mem =
(cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM;
req.Attributes |= WIN_ENABLE;
req.Base = mem->win[0].host_addr;
req.Size = mem->win[0].len;
/* new in dummy.cs 2001/01/28 MN
if (req.Size < 0x1000)
req.Size = 0x1000;
*/
req.AccessSpeed = 0;
if (pcmcia_request_window(&link, &req, &link->win) != 0)
goto next_entry;
map.Page = 0; map.CardOffset = mem->win[0].card_addr;
if (pcmcia_map_mem_page(link->win, &map) != 0)
goto next_entry;
}
/* If we got this far, we're cool! */
break;
next_entry:
CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(link, &tuple));
}
/*
Allocate an interrupt line. Note that this does not assign a
handler to the interrupt, unless the 'Handler' member of the
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ)
CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq));
/*
This actually configures the PCMCIA socket -- setting up
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf));
/*
At this point, the dev_node_t structure(s) need to be
initialized and arranged in a linked list at link->dev.
*/
sprintf(dev->node.dev_name, "sedlbauer");
dev->node.major = dev->node.minor = 0;
link->dev_node = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x:",
dev->node.dev_name, link->conf.ConfigIndex);
if (link->conf.Vpp)
printk(", Vpp %d.%d", link->conf.Vpp/10, link->conf.Vpp%10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req.Base,
req.Base+req.Size-1);
printk("\n");
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_SEDLBAUER_PCMCIA;
last_ret = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->stop), &icard);
if (last_ret < 0) {
printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d at i/o %#x\n",
last_ret, link->io.BasePort1);
sedlbauer_release(link);
return -ENODEV;
} else
((local_info_t*)link->priv)->cardnr = last_ret;
return 0;
cs_failed:
cs_error(link, last_fn, last_ret);
sedlbauer_release(link);
return -ENODEV;
} /* sedlbauer_config */
static int avma1cs_config(struct pcmcia_device *link)
{
tuple_t tuple;
cisparse_t parse;
cistpl_cftable_entry_t *cf = &parse.cftable_entry;
local_info_t *dev;
int i;
u_char buf[64];
char devname[128];
IsdnCard_t icard;
int busy = 0;
dev = link->priv;
DEBUG(0, "avma1cs_config(0x%p)\n", link);
/*
This reads the card's CONFIG tuple to find its configuration
registers.
*/
do {
tuple.DesiredTuple = CISTPL_CONFIG;
i = pcmcia_get_first_tuple(link, &tuple);
if (i != CS_SUCCESS) break;
tuple.TupleData = buf;
tuple.TupleDataMax = 64;
tuple.TupleOffset = 0;
i = pcmcia_get_tuple_data(link, &tuple);
if (i != CS_SUCCESS) break;
i = pcmcia_parse_tuple(link, &tuple, &parse);
if (i != CS_SUCCESS) break;
link->conf.ConfigBase = parse.config.base;
} while (0);
if (i != CS_SUCCESS) {
cs_error(link, ParseTuple, i);
return -ENODEV;
}
do {
tuple.Attributes = 0;
tuple.TupleData = buf;
tuple.TupleDataMax = 254;
tuple.TupleOffset = 0;
tuple.DesiredTuple = CISTPL_VERS_1;
devname[0] = 0;
if( !first_tuple(link, &tuple, &parse) && parse.version_1.ns > 1 ) {
strlcpy(devname,parse.version_1.str + parse.version_1.ofs[1],
sizeof(devname));
}
/*
* find IO port
*/
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleOffset = 0; tuple.TupleDataMax = 255;
tuple.Attributes = 0;
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
i = first_tuple(link, &tuple, &parse);
while (i == CS_SUCCESS) {
if (cf->io.nwin > 0) {
link->conf.ConfigIndex = cf->index;
link->io.BasePort1 = cf->io.win[0].base;
link->io.NumPorts1 = cf->io.win[0].len;
link->io.NumPorts2 = 0;
printk(KERN_INFO "avma1_cs: testing i/o %#x-%#x\n",
link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1 - 1);
i = pcmcia_request_io(link, &link->io);
if (i == CS_SUCCESS) goto found_port;
}
i = next_tuple(link, &tuple, &parse);
}
found_port:
if (i != CS_SUCCESS) {
cs_error(link, RequestIO, i);
break;
}
/*
* allocate an interrupt line
*/
i = pcmcia_request_irq(link, &link->irq);
if (i != CS_SUCCESS) {
cs_error(link, RequestIRQ, i);
/* undo */
pcmcia_disable_device(link);
break;
}
/*
* configure the PCMCIA socket
*/
i = pcmcia_request_configuration(link, &link->conf);
if (i != CS_SUCCESS) {
cs_error(link, RequestConfiguration, i);
pcmcia_disable_device(link);
break;
}
} while (0);
/* At this point, the dev_node_t structure(s) should be
initialized and arranged in a linked list at link->dev. */
strcpy(dev->node.dev_name, "A1");
dev->node.major = 45;
dev->node.minor = 0;
link->dev_node = &dev->node;
/* If any step failed, release any partially configured state */
if (i != 0) {
avma1cs_release(link);
return -ENODEV;
}
printk(KERN_NOTICE "avma1_cs: checking at i/o %#x, irq %d\n",
link->io.BasePort1, link->irq.AssignedIRQ);
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = isdnprot;
icard.typ = ISDN_CTYPE_A1_PCMCIA;
i = hisax_init_pcmcia(link, &busy, &icard);
if (i < 0) {
printk(KERN_ERR "avma1_cs: failed to initialize AVM A1 PCMCIA %d at i/o %#x\n", i, link->io.BasePort1);
avma1cs_release(link);
return -ENODEV;
}
dev->node.minor = i;
return 0;
} /* avma1cs_config */
static int __devinit sedlbauer_config(struct pcmcia_device *link)
{
win_req_t *req;
int ret;
IsdnCard_t icard;
dev_dbg(&link->dev, "sedlbauer_config(0x%p)\n", link);
req = kzalloc(sizeof(win_req_t), GFP_KERNEL);
if (!req)
return -ENOMEM;
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including
voltage, IO window, memory window, and interrupt settings.
We make no assumptions about the card to be configured: we use
just the information available in the CIS. In an ideal world,
this would work for any PCMCIA card, but it requires a complete
and accurate CIS. In practice, a driver usually "knows" most of
these things without consulting the CIS, and most client drivers
will only use the CIS to fill in implementation-defined details.
*/
ret = pcmcia_loop_config(link, sedlbauer_config_check, req);
if (ret)
goto failed;
/*
This actually configures the PCMCIA socket -- setting up
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
ret = pcmcia_request_configuration(link, &link->conf);
if (ret)
goto failed;
/* Finally, report what we've done */
dev_info(&link->dev, "index 0x%02x:",
link->conf.ConfigIndex);
if (link->conf.Vpp)
printk(", Vpp %d.%d", link->conf.Vpp/10, link->conf.Vpp%10);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
if (link->win)
printk(", mem 0x%06lx-0x%06lx", req->Base,
req->Base+req->Size-1);
printk("\n");
icard.para[0] = link->irq;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_SEDLBAUER_PCMCIA;
ret = hisax_init_pcmcia(link,
&(((local_info_t *)link->priv)->stop), &icard);
if (ret < 0) {
printk(KERN_ERR "sedlbauer_cs: failed to initialize SEDLBAUER PCMCIA %d at i/o %#x\n",
ret, link->io.BasePort1);
sedlbauer_release(link);
return -ENODEV;
} else
((local_info_t *)link->priv)->cardnr = ret;
return 0;
failed:
sedlbauer_release(link);
return -ENODEV;
} /* sedlbauer_config */
static int teles_cs_config(struct pcmcia_device *link)
{
tuple_t tuple;
cisparse_t parse;
local_info_t *dev;
int i, j, last_fn;
u_short buf[128];
cistpl_cftable_entry_t *cf = &parse.cftable_entry;
IsdnCard_t icard;
DEBUG(0, "teles_config(0x%p)\n", link);
dev = link->priv;
tuple.TupleData = (cisdata_t *)buf;
tuple.TupleOffset = 0; tuple.TupleDataMax = 255;
tuple.Attributes = 0;
tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
i = first_tuple(link, &tuple, &parse);
while (i == CS_SUCCESS) {
if ( (cf->io.nwin > 0) && cf->io.win[0].base) {
printk(KERN_INFO "(teles_cs: looks like the 96 model)\n");
link->conf.ConfigIndex = cf->index;
link->io.BasePort1 = cf->io.win[0].base;
i = pcmcia_request_io(link, &link->io);
if (i == CS_SUCCESS) break;
} else {
printk(KERN_INFO "(teles_cs: looks like the 97 model)\n");
link->conf.ConfigIndex = cf->index;
for (i = 0, j = 0x2f0; j > 0x100; j -= 0x10) {
link->io.BasePort1 = j;
i = pcmcia_request_io(link, &link->io);
if (i == CS_SUCCESS) break;
}
break;
}
i = next_tuple(link, &tuple, &parse);
}
if (i != CS_SUCCESS) {
last_fn = RequestIO;
goto cs_failed;
}
i = pcmcia_request_irq(link, &link->irq);
if (i != CS_SUCCESS) {
link->irq.AssignedIRQ = 0;
last_fn = RequestIRQ;
goto cs_failed;
}
i = pcmcia_request_configuration(link, &link->conf);
if (i != CS_SUCCESS) {
last_fn = RequestConfiguration;
goto cs_failed;
}
/* At this point, the dev_node_t structure(s) should be
initialized and arranged in a linked list at link->dev. *//* */
sprintf(dev->node.dev_name, "teles");
dev->node.major = dev->node.minor = 0x0;
link->dev_node = &dev->node;
/* Finally, report what we've done */
printk(KERN_INFO "%s: index 0x%02x:",
dev->node.dev_name, link->conf.ConfigIndex);
if (link->conf.Attributes & CONF_ENABLE_IRQ)
printk(", irq %d", link->irq.AssignedIRQ);
if (link->io.NumPorts1)
printk(", io 0x%04x-0x%04x", link->io.BasePort1,
link->io.BasePort1+link->io.NumPorts1-1);
if (link->io.NumPorts2)
printk(" & 0x%04x-0x%04x", link->io.BasePort2,
link->io.BasePort2+link->io.NumPorts2-1);
printk("\n");
icard.para[0] = link->irq.AssignedIRQ;
icard.para[1] = link->io.BasePort1;
icard.protocol = protocol;
icard.typ = ISDN_CTYPE_TELESPCMCIA;
i = hisax_init_pcmcia(link, &(((local_info_t*)link->priv)->busy), &icard);
if (i < 0) {
printk(KERN_ERR "teles_cs: failed to initialize Teles PCMCIA %d at i/o %#x\n",
i, link->io.BasePort1);
teles_cs_release(link);
return -ENODEV;
}
((local_info_t*)link->priv)->cardnr = i;
return 0;
cs_failed:
cs_error(link, last_fn, i);
teles_cs_release(link);
return -ENODEV;
} /* teles_cs_config */
