void ICACHE_FLASH_ATTR user_init()
{
// Initialize the GPIO subsystem.
//UART_init(BIT_RATE_115200, BIT_RATE_115200, 0);
//UART_SetPrintPort(UART0);
stdout_init();
i2c_master_gpio_init();
user_set_station_config();
pcf8754_i2c_write_byte(I2C_INPUT_ADDRESS, 0);
// =================================================
// Initialize GPIO2 and GPIO0 as GPIO
// =================================================
PIN_FUNC_SELECT(PERIPHS_IO_MUX_U0RXD_U, FUNC_GPIO3);
PIN_PULLUP_DIS(PERIPHS_IO_MUX_U0RXD_U);
gpio_output_set(0, 0, 0, GPIO_ID_PIN(3)); // set set gpio 0 as input
ETS_GPIO_INTR_DISABLE();
// Attach interrupt handle to gpio interrupts.
ETS_GPIO_INTR_ATTACH(gpio_intr_handler, NULL);
GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(3)); // clear gpio status
gpio_pin_intr_state_set(GPIO_ID_PIN(3), GPIO_PIN_INTR_ANYEDGE); // clear gpio status.
ETS_GPIO_INTR_ENABLE(); // Enable interrupts by GPIO
// register a callback function to let user code know that system
// initialization is complete
system_init_done_cb(&post_user_init_func);
//Start os task
system_os_task(user_procTask, user_procTaskPrio,user_procTaskQueue, user_procTaskQueueLen);
}
void ICACHE_FLASH_ATTR user_init(void) {
uart_div_modify(0, UART_CLK_FREQ / BAUD);
wifi_set_opmode(STATION_MODE);
wifi_station_connect();
/*** I²C init ***/
i2c_master_gpio_init();
mpu9250_init();
ak8963_init();
os_delay_us(10000);
i2c_scanbus();
/*** LCD Init ***/
ssd1306_init(0);
ssd1306_text_small(10, 10, "Init...");
ssd1306_flip();
// ~Charge input
PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTCK_U, FUNC_GPIO13);
gpio_output_set(0, 0, 0, BIT13);
// Button inputs
buttons_init();
ak8963_calibration_start(10000, on_ak8963_calibration);
os_printf("Startup\r\n");
}
void bus_init(void) {
#if ENABLE_BUS_I2C
i2c_master_gpio_init();
i2c_master_init();
#endif
#if ENABLE_BUS_ONEWIRE
onewire_init();
#endif
}
uint32_t platform_i2c_setup( unsigned id, uint8_t sda, uint8_t scl, uint32_t speed ){
if (sda >= NUM_GPIO || scl >= NUM_GPIO)
return 0;
// platform_pwm_close(sda);
// platform_pwm_close(scl);
// disable gpio interrupt first
platform_gpio_mode(sda, PLATFORM_GPIO_INPUT, PLATFORM_GPIO_PULLUP); // inside this func call platform_pwm_close
platform_gpio_mode(scl, PLATFORM_GPIO_INPUT, PLATFORM_GPIO_PULLUP); // disable gpio interrupt first
i2c_master_gpio_init(sda, scl);
return PLATFORM_I2C_SPEED_SLOW;
}
/*
* This is entry point for user code
*/
void user_init(void)
{
// Configure the UART
uart_init(BIT_RATE_9600,0);
i2c_master_gpio_init();
// Set up a timer to send the message
// os_timer_disarm(ETSTimer *ptimer)
os_timer_disarm(&read_timer);
// os_timer_setfn(ETSTimer *ptimer, ETSTimerFunc *pfunction, void *parg)
os_timer_setfn(&read_timer, read_cb, (void *)0);
// void os_timer_arm(ETSTimer *ptimer,uint32_t milliseconds, bool repeat_flag)
os_timer_arm(&read_timer, DELAY, 1);
}
/******************************************************************************
* FunctionName : user_init
* Description : entry of user application, init user function here
* Parameters : none
* Returns : none
*******************************************************************************/
void ICACHE_FLASH_ATTR user_init(void) {
system_init_done_cb(user_init_done);
// UART Devices
mod_rfid_init();
mod_finger_init();
mod_emtr_init();
devices_init();
debug("\n\nSDK version: %s\n", system_get_sdk_version());
debug("Firmware: %s\n", config_firmware_bin());
memory_info();
user_config_init();
user_config_load();
#if SSL_ENABLE
user_config_load_private_key();
user_config_load_certificate();
#endif
user_events_init();
// Scan
webserver_register_handler_callback(DEVICES_URL, devices_handler);
webserver_register_handler_callback(WIFI_SCAN_URL, wifi_scan_handler);
// Native Devices
user_button_init();
user_relay_init();
user_adc_init();
// I2C Devices
i2c_master_gpio_init();
mod_rgb_init();
mod_tc_mk2_init();
mod_io2_init();
mod_irda_init();
// SPI Devices
mod_led_8x8_rgb_init();
webserver_init();
}
/******************************************************************************
* FunctionName : user_init
* Description : entry of user application, init user function here
* Parameters : none
* Returns : none
*******************************************************************************/
void ICACHE_FLASH_ATTR user_init(void) {
system_init_done_cb(user_init_done);
// wifi_set_phy_mode(PHY_MODE_11N);
// wifi_set_sleep_type(MODEM_SLEEP_T);
#if UART0_SWAP
stdout_disable();
system_uart_swap();
#endif
#if UART1_ENABLE
stdout_init(UART1);
#endif
// UART Devices
#if DEVICE == PLUG
user_plug_init();
#endif
#if DEVICE == SWITCH1
user_switch1_init();
#endif
#if DEVICE == SWITCH2
user_switch2_init();
#endif
#if MOD_RFID_ENABLE
mod_rfid_init();
#endif
#if MOD_FINGER_ENABLE
mod_finger_init();
#endif
#if MOD_EMTR_ENABLE
mod_emtr_init();
#endif
devices_init();
debug("\n\nSDK version: %s\n", system_get_sdk_version());
debug("Firmware: %s\n", config_firmware_bin());
memory_info();
user_config_init();
user_config_load();
#if SSL_ENABLE
user_config_load_private_key();
user_config_load_certificate();
#endif
user_events_init();
// Scan
webserver_register_handler_callback(DEVICES_URL, devices_handler);
webserver_register_handler_callback(WIFI_SCAN_URL, wifi_scan_handler);
// Native Devices
#if BUTTON_ENABLE
user_button_init();
#endif
#if RELAY_ENABLE
user_relay_init();
#endif
#if ADC_ENABLE
user_adc_init();
#endif
#if BATTERY_ENABLE
user_battery_init();
#endif
#if I2C_ENABLE
// I2C Devices
i2c_master_gpio_init();
#if MOD_RGB_ENABLE
mod_rgb_init();
#endif
#if MOD_TC_MK2_ENABLE
mod_tc_mk2_init();
#endif
#if MOD_IO2_ENABLE
mod_io2_init();
#endif
#if MOD_IRDA_ENABLE
mod_irda_init();
#endif
#if DEVICE == DIMMER
user_dimmer_init();
#endif
#endif
// SPI Devices
#if MOD_LED_8x8_RGB_ENABLE
mod_led_8x8_rgb_init();
#endif
#if DEVICE == BADGE
badge_init();
#endif
key_init();
webserver_init();
}
/******************************************************************************
* FunctionName : user_mvh3004_init
* Description : init mvh3004, mainly i2c master gpio
* Parameters : none
* Returns : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
user_mvh3004_init(void)
{
i2c_master_gpio_init();
}
void ICACHE_FLASH_ATTR
mcp3221_init(void)
{
i2c_master_gpio_init();
}
/******************************************************************************
* FunctionName : user_init
* Description : entry of user application, init user function here
* Parameters : none
* Returns : none
*******************************************************************************/
void ICACHE_FLASH_ATTR user_init(void) {
system_init_done_cb(user_init_done);
// UART Devices
#if MOD_RFID_ENABLE
mod_rfid_init();
#endif
#if MOD_FINGER_ENABLE
mod_finger_init();
#endif
#if MOD_EMTR_ENABLE
mod_emtr_init();
#endif
devices_init();
debug("\n\nSDK version: %s\n", system_get_sdk_version());
debug("Firmware: %s\n", config_firmware_bin());
memory_info();
user_config_init();
user_config_load();
#if SSL_ENABLE
user_config_load_private_key();
user_config_load_certificate();
#endif
user_events_init();
// Scan
webserver_register_handler_callback(DEVICES_URL, devices_handler);
webserver_register_handler_callback(WIFI_SCAN_URL, wifi_scan_handler);
// Native Devices
#if BUTTON_ENABLE
user_button_init();
#endif
#if RELAY_ENABLE
user_relay_init();
#endif
#if ADC_ENABLE
user_adc_init();
#endif
#if BATTERY_ENABLE
user_battery_init();
#endif
// I2C Devices
i2c_master_gpio_init();
#if MOD_RGB_ENABLE
mod_rgb_init();
#endif
#if MOD_TC_MK2_ENABLE
mod_tc_mk2_init();
#endif
#if MOD_IO2_ENABLE
mod_io2_init();
#endif
#if MOD_IRDA_ENABLE
mod_irda_init();
#endif
// SPI Devices
#if MOD_LED_8x8_RGB_ENABLE
mod_led_8x8_rgb_init();
#endif
key_init();
webserver_init();
}
