static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw)
{
s32 ret_val = 0;
u32 mdicnfg;
u16 nvm_data = 0;
if (hw->mac.type != e1000_82580)
goto out;
if (!igb_sgmii_active_82575(hw))
goto out;
ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
&nvm_data);
if (ret_val) {
hw_dbg("NVM Read Error\n");
goto out;
}
mdicnfg = rd32(E1000_MDICNFG);
if (nvm_data & NVM_WORD24_EXT_MDIO)
mdicnfg |= E1000_MDICNFG_EXT_MDIO;
if (nvm_data & NVM_WORD24_COM_MDIO)
mdicnfg |= E1000_MDICNFG_COM_MDIO;
wr32(E1000_MDICNFG, mdicnfg);
out:
return ret_val;
}
/**
* igb_clear_hw_cntrs_82575 - Clear device specific hardware counters
* @hw: pointer to the HW structure
*
* Clears the hardware counters by reading the counter registers.
**/
static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw)
{
igb_clear_hw_cntrs_base(hw);
rd32(E1000_PRC64);
rd32(E1000_PRC127);
rd32(E1000_PRC255);
rd32(E1000_PRC511);
rd32(E1000_PRC1023);
rd32(E1000_PRC1522);
rd32(E1000_PTC64);
rd32(E1000_PTC127);
rd32(E1000_PTC255);
rd32(E1000_PTC511);
rd32(E1000_PTC1023);
rd32(E1000_PTC1522);
rd32(E1000_ALGNERRC);
rd32(E1000_RXERRC);
rd32(E1000_TNCRS);
rd32(E1000_CEXTERR);
rd32(E1000_TSCTC);
rd32(E1000_TSCTFC);
rd32(E1000_MGTPRC);
rd32(E1000_MGTPDC);
rd32(E1000_MGTPTC);
rd32(E1000_IAC);
rd32(E1000_ICRXOC);
rd32(E1000_ICRXPTC);
rd32(E1000_ICRXATC);
rd32(E1000_ICTXPTC);
rd32(E1000_ICTXATC);
rd32(E1000_ICTXQEC);
rd32(E1000_ICTXQMTC);
rd32(E1000_ICRXDMTC);
rd32(E1000_CBTMPC);
rd32(E1000_HTDPMC);
rd32(E1000_CBRMPC);
rd32(E1000_RPTHC);
rd32(E1000_HGPTC);
rd32(E1000_HTCBDPC);
rd32(E1000_HGORCL);
rd32(E1000_HGORCH);
rd32(E1000_HGOTCL);
rd32(E1000_HGOTCH);
rd32(E1000_LENERRS);
/* This register should not be read in copper configurations */
if (hw->phy.media_type == e1000_media_type_internal_serdes ||
igb_sgmii_active_82575(hw))
rd32(E1000_SCVPC);
}
static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
{
u32 ctrl;
s32 ret_val;
ctrl = rd32(E1000_CTRL);
ctrl |= E1000_CTRL_SLU;
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
wr32(E1000_CTRL, ctrl);
ret_val = igb_setup_serdes_link_82575(hw);
if (ret_val)
goto out;
if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
msleep(300);
ret_val = hw->phy.ops.reset(hw);
if (ret_val) {
hw_dbg("Error resetting the PHY.\n");
goto out;
}
}
switch (hw->phy.type) {
case e1000_phy_m88:
if (hw->phy.id == I347AT4_E_PHY_ID ||
hw->phy.id == M88E1112_E_PHY_ID)
ret_val = igb_copper_link_setup_m88_gen2(hw);
else
ret_val = igb_copper_link_setup_m88(hw);
break;
case e1000_phy_igp_3:
ret_val = igb_copper_link_setup_igp(hw);
break;
case e1000_phy_82580:
ret_val = igb_copper_link_setup_82580(hw);
break;
default:
ret_val = -E1000_ERR_PHY;
break;
}
if (ret_val)
goto out;
ret_val = igb_setup_copper_link(hw);
out:
return ret_val;
}
/**
* igb_setup_copper_link_82575 - Configure copper link settings
* @hw: pointer to the HW structure
*
* Configures the link for auto-neg or forced speed and duplex. Then we check
* for link, once link is established calls to configure collision distance
* and flow control are called.
**/
static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
{
u32 ctrl;
s32 ret_val;
ctrl = rd32(E1000_CTRL);
ctrl |= E1000_CTRL_SLU;
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
wr32(E1000_CTRL, ctrl);
ret_val = igb_setup_serdes_link_82575(hw);
if (ret_val)
goto out;
if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
/* allow time for SFP cage time to power up phy */
msleep(300);
ret_val = hw->phy.ops.reset(hw);
if (ret_val) {
hw_dbg("Error resetting the PHY.\n");
goto out;
}
}
switch (hw->phy.type) {
case e1000_phy_m88:
ret_val = igb_copper_link_setup_m88(hw);
break;
case e1000_phy_igp_3:
ret_val = igb_copper_link_setup_igp(hw);
break;
case e1000_phy_82580:
ret_val = igb_copper_link_setup_82580(hw);
break;
default:
ret_val = -E1000_ERR_PHY;
break;
}
if (ret_val)
goto out;
ret_val = igb_setup_copper_link(hw);
out:
return ret_val;
}
/**
* igb_shutdown_serdes_link_82575 - Remove link during power down
* @hw: pointer to the HW structure
*
* In the case of fiber serdes, shut down optics and PCS on driver unload
* when management pass thru is not enabled.
**/
void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
u16 eeprom_data = 0;
if (hw->phy.media_type != e1000_media_type_internal_serdes ||
igb_sgmii_active_82575(hw))
return;
if (hw->bus.func == E1000_FUNC_0)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
else if (hw->mac.type == e1000_82580)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
&eeprom_data);
else if (hw->bus.func == E1000_FUNC_1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
/*
* If APM is not enabled in the EEPROM and management interface is
* not enabled, then power down.
*/
if (!(eeprom_data & E1000_NVM_APME_82575) &&
!igb_enable_mng_pass_thru(hw)) {
/* Disable PCS to turn off link */
reg = rd32(E1000_PCS_CFG0);
reg &= ~E1000_PCS_CFG_PCS_EN;
wr32(E1000_PCS_CFG0, reg);
/* shutdown the laser */
reg = rd32(E1000_CTRL_EXT);
reg |= E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
/* flush the write to verify completion */
wrfl();
msleep(1);
}
return;
}
/**
* igb_power_up_serdes_link_82575 - Power up the serdes link after shutdown
* @hw: pointer to the HW structure
**/
void igb_power_up_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
return;
/* Enable PCS to turn on link */
reg = rd32(E1000_PCS_CFG0);
reg |= E1000_PCS_CFG_PCS_EN;
wr32(E1000_PCS_CFG0, reg);
/* Power up the laser */
reg = rd32(E1000_CTRL_EXT);
reg &= ~E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
/* flush the write to verify completion */
wrfl();
msleep(1);
}
void igb_power_up_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
return;
reg = rd32(E1000_PCS_CFG0);
reg |= E1000_PCS_CFG_PCS_EN;
wr32(E1000_PCS_CFG0, reg);
reg = rd32(E1000_CTRL_EXT);
reg &= ~E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
wrfl();
msleep(1);
}
/**
* igb_shutdown_serdes_link_82575 - Remove link during power down
* @hw: pointer to the HW structure
*
* In the case of fiber serdes, shut down optics and PCS on driver unload
* when management pass thru is not enabled.
**/
void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
if (hw->phy.media_type != e1000_media_type_internal_serdes &&
igb_sgmii_active_82575(hw))
return;
if (!igb_enable_mng_pass_thru(hw)) {
/* Disable PCS to turn off link */
reg = rd32(E1000_PCS_CFG0);
reg &= ~E1000_PCS_CFG_PCS_EN;
wr32(E1000_PCS_CFG0, reg);
/* shutdown the laser */
reg = rd32(E1000_CTRL_EXT);
reg |= E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
/* flush the write to verify completion */
wrfl();
msleep(1);
}
}
void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
{
u32 reg;
if (hw->phy.media_type != e1000_media_type_internal_serdes &&
igb_sgmii_active_82575(hw))
return;
if (!igb_enable_mng_pass_thru(hw)) {
reg = rd32(E1000_PCS_CFG0);
reg &= ~E1000_PCS_CFG_PCS_EN;
wr32(E1000_PCS_CFG0, reg);
reg = rd32(E1000_CTRL_EXT);
reg |= E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, reg);
wrfl();
msleep(1);
}
}
static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
struct e1000_nvm_info *nvm = &hw->nvm;
struct e1000_mac_info *mac = &hw->mac;
struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575;
u32 eecd;
s32 ret_val;
u16 size;
u32 ctrl_ext = 0;
switch (hw->device_id) {
case E1000_DEV_ID_82575EB_COPPER:
case E1000_DEV_ID_82575EB_FIBER_SERDES:
case E1000_DEV_ID_82575GB_QUAD_COPPER:
mac->type = e1000_82575;
break;
case E1000_DEV_ID_82576:
case E1000_DEV_ID_82576_NS:
case E1000_DEV_ID_82576_NS_SERDES:
case E1000_DEV_ID_82576_FIBER:
case E1000_DEV_ID_82576_SERDES:
case E1000_DEV_ID_82576_QUAD_COPPER:
case E1000_DEV_ID_82576_SERDES_QUAD:
mac->type = e1000_82576;
break;
case E1000_DEV_ID_82580_COPPER:
case E1000_DEV_ID_82580_FIBER:
case E1000_DEV_ID_82580_SERDES:
case E1000_DEV_ID_82580_SGMII:
case E1000_DEV_ID_82580_COPPER_DUAL:
mac->type = e1000_82580;
break;
default:
return -E1000_ERR_MAC_INIT;
break;
}
/* Set media type */
/*
* The 82575 uses bits 22:23 for link mode. The mode can be changed
* based on the EEPROM. We cannot rely upon device ID. There
* is no distinguishable difference between fiber and internal
* SerDes mode on the 82575. There can be an external PHY attached
* on the SGMII interface. For this, we'll set sgmii_active to true.
*/
phy->media_type = e1000_media_type_copper;
dev_spec->sgmii_active = false;
ctrl_ext = rd32(E1000_CTRL_EXT);
switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
case E1000_CTRL_EXT_LINK_MODE_SGMII:
dev_spec->sgmii_active = true;
ctrl_ext |= E1000_CTRL_I2C_ENA;
break;
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
hw->phy.media_type = e1000_media_type_internal_serdes;
ctrl_ext |= E1000_CTRL_I2C_ENA;
break;
default:
ctrl_ext &= ~E1000_CTRL_I2C_ENA;
break;
}
wr32(E1000_CTRL_EXT, ctrl_ext);
/*
* if using i2c make certain the MDICNFG register is cleared to prevent
* communications from being misrouted to the mdic registers
*/
if ((ctrl_ext & E1000_CTRL_I2C_ENA) && (hw->mac.type == e1000_82580))
wr32(E1000_MDICNFG, 0);
/* Set mta register count */
mac->mta_reg_count = 128;
/* Set rar entry count */
mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
if (mac->type == e1000_82576)
mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
if (mac->type == e1000_82580)
mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
/* reset */
if (mac->type == e1000_82580)
mac->ops.reset_hw = igb_reset_hw_82580;
else
mac->ops.reset_hw = igb_reset_hw_82575;
/* Set if part includes ASF firmware */
mac->asf_firmware_present = true;
/* Set if manageability features are enabled. */
mac->arc_subsystem_valid =
(rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK)
? true : false;
/* physical interface link setup */
mac->ops.setup_physical_interface =
(hw->phy.media_type == e1000_media_type_copper)
? igb_setup_copper_link_82575
: igb_setup_serdes_link_82575;
/* NVM initialization */
eecd = rd32(E1000_EECD);
nvm->opcode_bits = 8;
nvm->delay_usec = 1;
switch (nvm->override) {
case e1000_nvm_override_spi_large:
nvm->page_size = 32;
nvm->address_bits = 16;
break;
case e1000_nvm_override_spi_small:
nvm->page_size = 8;
nvm->address_bits = 8;
break;
default:
nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
break;
}
nvm->type = e1000_nvm_eeprom_spi;
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
/*
* Added to a constant, "size" becomes the left-shift value
* for setting word_size.
*/
size += NVM_WORD_SIZE_BASE_SHIFT;
/* EEPROM access above 16k is unsupported */
if (size > 14)
size = 14;
nvm->word_size = 1 << size;
/* if 82576 then initialize mailbox parameters */
if (mac->type == e1000_82576)
igb_init_mbx_params_pf(hw);
/* setup PHY parameters */
if (phy->media_type != e1000_media_type_copper) {
phy->type = e1000_phy_none;
return 0;
}
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
phy->reset_delay_us = 100;
/* PHY function pointers */
if (igb_sgmii_active_82575(hw)) {
phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
} else if (hw->mac.type == e1000_82580) {
phy->ops.reset = igb_phy_hw_reset;
phy->ops.read_reg = igb_read_phy_reg_82580;
phy->ops.write_reg = igb_write_phy_reg_82580;
} else {
phy->ops.reset = igb_phy_hw_reset;
phy->ops.read_reg = igb_read_phy_reg_igp;
phy->ops.write_reg = igb_write_phy_reg_igp;
}
/* set lan id */
hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >>
E1000_STATUS_FUNC_SHIFT;
/* Set phy->phy_addr and phy->id. */
ret_val = igb_get_phy_id_82575(hw);
if (ret_val)
return ret_val;
/* Verify phy id and set remaining function pointers */
switch (phy->id) {
case M88E1111_I_PHY_ID:
phy->type = e1000_phy_m88;
phy->ops.get_phy_info = igb_get_phy_info_m88;
phy->ops.get_cable_length = igb_get_cable_length_m88;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
break;
case IGP03E1000_E_PHY_ID:
phy->type = e1000_phy_igp_3;
phy->ops.get_phy_info = igb_get_phy_info_igp;
phy->ops.get_cable_length = igb_get_cable_length_igp_2;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp;
phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
break;
case I82580_I_PHY_ID:
phy->type = e1000_phy_82580;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
phy->ops.get_cable_length = igb_get_cable_length_82580;
phy->ops.get_phy_info = igb_get_phy_info_82580;
break;
default:
return -E1000_ERR_PHY;
}
return 0;
}
/**
* igb_get_phy_id_82575 - Retrieve PHY addr and id
* @hw: pointer to the HW structure
*
* Retrieves the PHY address and ID for both PHY's which do and do not use
* sgmi interface.
**/
static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val = 0;
u16 phy_id;
u32 ctrl_ext;
/*
* For SGMII PHYs, we try the list of possible addresses until
* we find one that works. For non-SGMII PHYs
* (e.g. integrated copper PHYs), an address of 1 should
* work. The result of this function should mean phy->phy_addr
* and phy->id are set correctly.
*/
if (!(igb_sgmii_active_82575(hw))) {
phy->addr = 1;
ret_val = igb_get_phy_id(hw);
goto out;
}
/* Power on sgmii phy if it is disabled */
ctrl_ext = rd32(E1000_CTRL_EXT);
wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA);
wrfl();
msleep(300);
/*
* The address field in the I2CCMD register is 3 bits and 0 is invalid.
* Therefore, we need to test 1-7
*/
for (phy->addr = 1; phy->addr < 8; phy->addr++) {
ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id);
if (ret_val == 0) {
hw_dbg("Vendor ID 0x%08X read at address %u\n",
phy_id, phy->addr);
/*
* At the time of this writing, The M88 part is
* the only supported SGMII PHY product.
*/
if (phy_id == M88_VENDOR)
break;
} else {
hw_dbg("PHY address %u was unreadable\n", phy->addr);
}
}
/* A valid PHY type couldn't be found. */
if (phy->addr == 8) {
phy->addr = 0;
ret_val = -E1000_ERR_PHY;
goto out;
} else {
ret_val = igb_get_phy_id(hw);
}
/* restore previous sfp cage power state */
wr32(E1000_CTRL_EXT, ctrl_ext);
out:
return ret_val;
}
/**
* igb_setup_serdes_link_82575 - Setup link for serdes
* @hw: pointer to the HW structure
*
* Configure the physical coding sub-layer (PCS) link. The PCS link is
* used on copper connections where the serialized gigabit media independent
* interface (sgmii), or serdes fiber is being used. Configures the link
* for auto-negotiation or forces speed/duplex.
**/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
u32 ctrl_ext, ctrl_reg, reg;
bool pcs_autoneg;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
return 0;
/*
* On the 82575, SerDes loopback mode persists until it is
* explicitly turned off or a power cycle is performed. A read to
* the register does not indicate its status. Therefore, we ensure
* loopback mode is disabled during initialization.
*/
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
/* power on the sfp cage if present */
ctrl_ext = rd32(E1000_CTRL_EXT);
ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, ctrl_ext);
ctrl_reg = rd32(E1000_CTRL);
ctrl_reg |= E1000_CTRL_SLU;
if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) {
/* set both sw defined pins */
ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1;
/* Set switch control to serdes energy detect */
reg = rd32(E1000_CONNSW);
reg |= E1000_CONNSW_ENRGSRC;
wr32(E1000_CONNSW, reg);
}
reg = rd32(E1000_PCS_LCTL);
/* default pcs_autoneg to the same setting as mac autoneg */
pcs_autoneg = hw->mac.autoneg;
switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
case E1000_CTRL_EXT_LINK_MODE_SGMII:
/* sgmii mode lets the phy handle forcing speed/duplex */
pcs_autoneg = true;
/* autoneg time out should be disabled for SGMII mode */
reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
break;
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
/* disable PCS autoneg and support parallel detect only */
pcs_autoneg = false;
default:
/*
* non-SGMII modes only supports a speed of 1000/Full for the
* link so it is best to just force the MAC and let the pcs
* link either autoneg or be forced to 1000/Full
*/
ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
E1000_CTRL_FD | E1000_CTRL_FRCDPX;
/* set speed of 1000/Full if speed/duplex is forced */
reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
break;
}
wr32(E1000_CTRL, ctrl_reg);
/*
* New SerDes mode allows for forcing speed or autonegotiating speed
* at 1gb. Autoneg should be default set by most drivers. This is the
* mode that will be compatible with older link partners and switches.
* However, both are supported by the hardware and some drivers/tools.
*/
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
/*
* We force flow control to prevent the CTRL register values from being
* overwritten by the autonegotiated flow control values
*/
reg |= E1000_PCS_LCTL_FORCE_FCTRL;
if (pcs_autoneg) {
/* Set PCS register for autoneg */
reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
/* Set PCS register for forced link */
reg |= E1000_PCS_LCTL_FSD; /* Force Speed */
hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
wr32(E1000_PCS_LCTL, reg);
if (!igb_sgmii_active_82575(hw))
igb_force_mac_fc(hw);
return 0;
}
static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
struct e1000_nvm_info *nvm = &hw->nvm;
struct e1000_mac_info *mac = &hw->mac;
struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575;
u32 eecd;
s32 ret_val;
u16 size;
u32 ctrl_ext = 0;
switch (hw->device_id) {
case E1000_DEV_ID_82575EB_COPPER:
case E1000_DEV_ID_82575EB_FIBER_SERDES:
case E1000_DEV_ID_82575GB_QUAD_COPPER:
mac->type = e1000_82575;
break;
case E1000_DEV_ID_82576:
case E1000_DEV_ID_82576_NS:
case E1000_DEV_ID_82576_NS_SERDES:
case E1000_DEV_ID_82576_FIBER:
case E1000_DEV_ID_82576_SERDES:
case E1000_DEV_ID_82576_QUAD_COPPER:
case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
case E1000_DEV_ID_82576_SERDES_QUAD:
mac->type = e1000_82576;
break;
case E1000_DEV_ID_82580_COPPER:
case E1000_DEV_ID_82580_FIBER:
case E1000_DEV_ID_82580_QUAD_FIBER:
case E1000_DEV_ID_82580_SERDES:
case E1000_DEV_ID_82580_SGMII:
case E1000_DEV_ID_82580_COPPER_DUAL:
case E1000_DEV_ID_DH89XXCC_SGMII:
case E1000_DEV_ID_DH89XXCC_SERDES:
case E1000_DEV_ID_DH89XXCC_BACKPLANE:
case E1000_DEV_ID_DH89XXCC_SFP:
mac->type = e1000_82580;
break;
case E1000_DEV_ID_I350_COPPER:
case E1000_DEV_ID_I350_FIBER:
case E1000_DEV_ID_I350_SERDES:
case E1000_DEV_ID_I350_SGMII:
mac->type = e1000_i350;
break;
default:
return -E1000_ERR_MAC_INIT;
break;
}
phy->media_type = e1000_media_type_copper;
dev_spec->sgmii_active = false;
ctrl_ext = rd32(E1000_CTRL_EXT);
switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
case E1000_CTRL_EXT_LINK_MODE_SGMII:
dev_spec->sgmii_active = true;
break;
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
hw->phy.media_type = e1000_media_type_internal_serdes;
break;
default:
break;
}
mac->mta_reg_count = 128;
mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
if (mac->type == e1000_82576)
mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
if (mac->type == e1000_82580)
mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
if (mac->type == e1000_i350)
mac->rar_entry_count = E1000_RAR_ENTRIES_I350;
if (mac->type >= e1000_82580)
mac->ops.reset_hw = igb_reset_hw_82580;
else
mac->ops.reset_hw = igb_reset_hw_82575;
mac->asf_firmware_present = true;
mac->arc_subsystem_valid =
(rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK)
? true : false;
if (mac->type == e1000_i350)
dev_spec->eee_disable = false;
else
dev_spec->eee_disable = true;
mac->ops.setup_physical_interface =
(hw->phy.media_type == e1000_media_type_copper)
? igb_setup_copper_link_82575
: igb_setup_serdes_link_82575;
eecd = rd32(E1000_EECD);
nvm->opcode_bits = 8;
nvm->delay_usec = 1;
switch (nvm->override) {
case e1000_nvm_override_spi_large:
nvm->page_size = 32;
nvm->address_bits = 16;
break;
case e1000_nvm_override_spi_small:
nvm->page_size = 8;
nvm->address_bits = 8;
break;
default:
nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
break;
}
nvm->type = e1000_nvm_eeprom_spi;
size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
E1000_EECD_SIZE_EX_SHIFT);
size += NVM_WORD_SIZE_BASE_SHIFT;
if ((hw->mac.type == e1000_82576) && (size > 15)) {
pr_notice("The NVM size is not valid, defaulting to 32K\n");
size = 15;
}
nvm->word_size = 1 << size;
if (nvm->word_size == (1 << 15))
nvm->page_size = 128;
nvm->ops.acquire = igb_acquire_nvm_82575;
if (nvm->word_size < (1 << 15))
nvm->ops.read = igb_read_nvm_eerd;
else
nvm->ops.read = igb_read_nvm_spi;
nvm->ops.release = igb_release_nvm_82575;
switch (hw->mac.type) {
case e1000_82580:
nvm->ops.validate = igb_validate_nvm_checksum_82580;
nvm->ops.update = igb_update_nvm_checksum_82580;
break;
case e1000_i350:
nvm->ops.validate = igb_validate_nvm_checksum_i350;
nvm->ops.update = igb_update_nvm_checksum_i350;
break;
default:
nvm->ops.validate = igb_validate_nvm_checksum;
nvm->ops.update = igb_update_nvm_checksum;
}
nvm->ops.write = igb_write_nvm_spi;
switch (mac->type) {
case e1000_82576:
case e1000_i350:
igb_init_mbx_params_pf(hw);
break;
default:
break;
}
if (phy->media_type != e1000_media_type_copper) {
phy->type = e1000_phy_none;
return 0;
}
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
phy->reset_delay_us = 100;
ctrl_ext = rd32(E1000_CTRL_EXT);
if (igb_sgmii_active_82575(hw)) {
phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
ctrl_ext |= E1000_CTRL_I2C_ENA;
} else {
phy->ops.reset = igb_phy_hw_reset;
ctrl_ext &= ~E1000_CTRL_I2C_ENA;
}
wr32(E1000_CTRL_EXT, ctrl_ext);
igb_reset_mdicnfg_82580(hw);
if (igb_sgmii_active_82575(hw) && !igb_sgmii_uses_mdio_82575(hw)) {
phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
} else if (hw->mac.type >= e1000_82580) {
phy->ops.read_reg = igb_read_phy_reg_82580;
phy->ops.write_reg = igb_write_phy_reg_82580;
} else {
phy->ops.read_reg = igb_read_phy_reg_igp;
phy->ops.write_reg = igb_write_phy_reg_igp;
}
hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >>
E1000_STATUS_FUNC_SHIFT;
ret_val = igb_get_phy_id_82575(hw);
if (ret_val)
return ret_val;
switch (phy->id) {
case I347AT4_E_PHY_ID:
case M88E1112_E_PHY_ID:
case M88E1111_I_PHY_ID:
phy->type = e1000_phy_m88;
phy->ops.get_phy_info = igb_get_phy_info_m88;
if (phy->id == I347AT4_E_PHY_ID ||
phy->id == M88E1112_E_PHY_ID)
phy->ops.get_cable_length = igb_get_cable_length_m88_gen2;
else
phy->ops.get_cable_length = igb_get_cable_length_m88;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
break;
case IGP03E1000_E_PHY_ID:
phy->type = e1000_phy_igp_3;
phy->ops.get_phy_info = igb_get_phy_info_igp;
phy->ops.get_cable_length = igb_get_cable_length_igp_2;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp;
phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
break;
case I82580_I_PHY_ID:
case I350_I_PHY_ID:
phy->type = e1000_phy_82580;
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
phy->ops.get_cable_length = igb_get_cable_length_82580;
phy->ops.get_phy_info = igb_get_phy_info_82580;
break;
default:
return -E1000_ERR_PHY;
}
return 0;
}
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
u32 ctrl_ext, ctrl_reg, reg;
bool pcs_autoneg;
s32 ret_val = E1000_SUCCESS;
u16 data;
if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
!igb_sgmii_active_82575(hw))
return ret_val;
wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
ctrl_ext = rd32(E1000_CTRL_EXT);
ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
wr32(E1000_CTRL_EXT, ctrl_ext);
ctrl_reg = rd32(E1000_CTRL);
ctrl_reg |= E1000_CTRL_SLU;
if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) {
ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1;
reg = rd32(E1000_CONNSW);
reg |= E1000_CONNSW_ENRGSRC;
wr32(E1000_CONNSW, reg);
}
reg = rd32(E1000_PCS_LCTL);
pcs_autoneg = hw->mac.autoneg;
switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
case E1000_CTRL_EXT_LINK_MODE_SGMII:
pcs_autoneg = true;
reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
break;
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
pcs_autoneg = false;
default:
if (hw->mac.type == e1000_82575 ||
hw->mac.type == e1000_82576) {
ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data);
if (ret_val) {
printk(KERN_DEBUG "NVM Read Error\n\n");
return ret_val;
}
if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT)
pcs_autoneg = false;
}
ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
E1000_CTRL_FD | E1000_CTRL_FRCDPX;
reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
break;
}
wr32(E1000_CTRL, ctrl_reg);
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
/*
* We force flow control to prevent the CTRL register values from being
* overwritten by the autonegotiated flow control values
*/
reg |= E1000_PCS_LCTL_FORCE_FCTRL;
if (pcs_autoneg) {
reg |= E1000_PCS_LCTL_AN_ENABLE |
E1000_PCS_LCTL_AN_RESTART;
hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
reg |= E1000_PCS_LCTL_FSD;
hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
wr32(E1000_PCS_LCTL, reg);
if (!igb_sgmii_active_82575(hw))
igb_force_mac_fc(hw);
return ret_val;
}
static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
s32 ret_val = 0;
u16 phy_id;
u32 ctrl_ext;
u32 mdic;
if (!(igb_sgmii_active_82575(hw))) {
phy->addr = 1;
ret_val = igb_get_phy_id(hw);
goto out;
}
if (igb_sgmii_uses_mdio_82575(hw)) {
switch (hw->mac.type) {
case e1000_82575:
case e1000_82576:
mdic = rd32(E1000_MDIC);
mdic &= E1000_MDIC_PHY_MASK;
phy->addr = mdic >> E1000_MDIC_PHY_SHIFT;
break;
case e1000_82580:
case e1000_i350:
mdic = rd32(E1000_MDICNFG);
mdic &= E1000_MDICNFG_PHY_MASK;
phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT;
break;
default:
ret_val = -E1000_ERR_PHY;
goto out;
break;
}
ret_val = igb_get_phy_id(hw);
goto out;
}
ctrl_ext = rd32(E1000_CTRL_EXT);
wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA);
wrfl();
msleep(300);
for (phy->addr = 1; phy->addr < 8; phy->addr++) {
ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id);
if (ret_val == 0) {
hw_dbg("Vendor ID 0x%08X read at address %u\n",
phy_id, phy->addr);
if (phy_id == M88_VENDOR)
break;
} else {
hw_dbg("PHY address %u was unreadable\n", phy->addr);
}
}
if (phy->addr == 8) {
phy->addr = 0;
ret_val = -E1000_ERR_PHY;
goto out;
} else {
ret_val = igb_get_phy_id(hw);
}
wr32(E1000_CTRL_EXT, ctrl_ext);
out:
return ret_val;
}
