void __init setup_local_APIC (void)
{
unsigned long oldvalue, value, ver, maxlvt;
/* Pound the ESR really hard over the head with a big hammer - mbligh */
if (esr_disable) {
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
}
value = apic_read(APIC_LVR);
ver = GET_APIC_VERSION(value);
if ((SPURIOUS_APIC_VECTOR & 0x0f) != 0x0f)
__error_in_apic_c();
/*
* Double-check whether this APIC is really registered.
*/
if (!apic_id_registered())
BUG();
/*
* Intel recommends to set DFR, LDR and TPR before enabling
* an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
* document number 292116). So here it goes...
*/
init_apic_ldr();
/*
* Set Task Priority to 'accept all'. We never change this
* later on.
*/
value = apic_read(APIC_TASKPRI);
value &= ~APIC_TPRI_MASK;
apic_write_around(APIC_TASKPRI, value);
/*
* Now that we are all set up, enable the APIC
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
/*
* Enable APIC
*/
value |= APIC_SPIV_APIC_ENABLED;
/*
* Some unknown Intel IO/APIC (or APIC) errata is biting us with
* certain networking cards. If high frequency interrupts are
* happening on a particular IOAPIC pin, plus the IOAPIC routing
* entry is masked/unmasked at a high rate as well then sooner or
* later IOAPIC line gets 'stuck', no more interrupts are received
* from the device. If focus CPU is disabled then the hang goes
* away, oh well :-(
*
* [ This bug can be reproduced easily with a level-triggered
* PCI Ne2000 networking cards and PII/PIII processors, dual
* BX chipset. ]
*/
/*
* Actually disabling the focus CPU check just makes the hang less
* frequent as it makes the interrupt distributon model be more
* like LRU than MRU (the short-term load is more even across CPUs).
* See also the comment in end_level_ioapic_irq(). --macro
*/
#if 1
/* Enable focus processor (bit==0) */
value &= ~APIC_SPIV_FOCUS_DISABLED;
#else
/* Disable focus processor (bit==1) */
value |= APIC_SPIV_FOCUS_DISABLED;
#endif
/*
* Set spurious IRQ vector
*/
value |= SPURIOUS_APIC_VECTOR;
apic_write_around(APIC_SPIV, value);
/*
* Set up LVT0, LVT1:
*
* set up through-local-APIC on the BP's LINT0. This is not
* strictly necessery in pure symmetric-IO mode, but sometimes
* we delegate interrupts to the 8259A.
*/
/*
* TODO: set up through-local-APIC from through-I/O-APIC? --macro
*/
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && (pic_mode || !value)) {
value = APIC_DM_EXTINT;
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
smp_processor_id());
} else {
value = APIC_DM_EXTINT | APIC_LVT_MASKED;
apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
smp_processor_id());
}
apic_write_around(APIC_LVT0, value);
/*
* only the BP should see the LINT1 NMI signal, obviously.
*/
if (!smp_processor_id())
value = APIC_DM_NMI;
else
value = APIC_DM_NMI | APIC_LVT_MASKED;
if (!APIC_INTEGRATED(ver)) /* 82489DX */
value |= APIC_LVT_LEVEL_TRIGGER;
apic_write_around(APIC_LVT1, value);
if (APIC_INTEGRATED(ver) && !esr_disable) { /* !82489DX */
maxlvt = get_maxlvt();
if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
apic_write(APIC_ESR, 0);
oldvalue = apic_read(APIC_ESR);
value = ERROR_APIC_VECTOR; // enables sending errors
apic_write_around(APIC_LVTERR, value);
/*
* spec says clear errors after enabling vector.
*/
if (maxlvt > 3)
apic_write(APIC_ESR, 0);
value = apic_read(APIC_ESR);
if (value != oldvalue)
apic_printk(APIC_VERBOSE, "ESR value before enabling "
"vector: 0x%08lx after: 0x%08lx\n",
oldvalue, value);
} else {
if (esr_disable)
/*
* Something untraceble is creating bad interrupts on
* secondary quads ... for the moment, just leave the
* ESR disabled - we can't do anything useful with the
* errors anyway - mbligh
*/
printk("Leaving ESR disabled.\n");
else
printk("No ESR for 82489DX.\n");
}
if (nmi_watchdog == NMI_LOCAL_APIC)
setup_apic_nmi_watchdog();
apic_pm_activate();
}
/**
* setup_local_APIC - setup the local APIC
*/
void __cpuinit setup_local_APIC(void)
{
unsigned int value;
int i, j;
value = apic_read(APIC_LVR);
BUILD_BUG_ON((SPURIOUS_APIC_VECTOR & 0x0f) != 0x0f);
/*
* Double-check whether this APIC is really registered.
* This is meaningless in clustered apic mode, so we skip it.
*/
if (!apic_id_registered())
BUG();
/*
* Intel recommends to set DFR, LDR and TPR before enabling
* an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
* document number 292116). So here it goes...
*/
init_apic_ldr();
/*
* Set Task Priority to 'accept all'. We never change this
* later on.
*/
value = apic_read(APIC_TASKPRI);
value &= ~APIC_TPRI_MASK;
apic_write(APIC_TASKPRI, value);
/*
* After a crash, we no longer service the interrupts and a pending
* interrupt from previous kernel might still have ISR bit set.
*
* Most probably by now CPU has serviced that pending interrupt and
* it might not have done the ack_APIC_irq() because it thought,
* interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
* does not clear the ISR bit and cpu thinks it has already serivced
* the interrupt. Hence a vector might get locked. It was noticed
* for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
*/
for (i = APIC_ISR_NR - 1; i >= 0; i--) {
value = apic_read(APIC_ISR + i*0x10);
for (j = 31; j >= 0; j--) {
if (value & (1<<j))
ack_APIC_irq();
}
}
/*
* Now that we are all set up, enable the APIC
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
/*
* Enable APIC
*/
value |= APIC_SPIV_APIC_ENABLED;
/* We always use processor focus */
/*
* Set spurious IRQ vector
*/
value |= SPURIOUS_APIC_VECTOR;
apic_write(APIC_SPIV, value);
/*
* Set up LVT0, LVT1:
*
* set up through-local-APIC on the BP's LINT0. This is not
* strictly necessary in pure symmetric-IO mode, but sometimes
* we delegate interrupts to the 8259A.
*/
/*
* TODO: set up through-local-APIC from through-I/O-APIC? --macro
*/
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && !value) {
value = APIC_DM_EXTINT;
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
smp_processor_id());
} else {
value = APIC_DM_EXTINT | APIC_LVT_MASKED;
apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
smp_processor_id());
}
apic_write(APIC_LVT0, value);
/*
* only the BP should see the LINT1 NMI signal, obviously.
*/
if (!smp_processor_id())
value = APIC_DM_NMI;
else
value = APIC_DM_NMI | APIC_LVT_MASKED;
apic_write(APIC_LVT1, value);
}
void __devinit setup_local_APIC(void)
{
unsigned long oldvalue, value, ver, maxlvt;
int i, j;
/* Pound the ESR really hard over the head with a big hammer - mbligh */
if (esr_disable) {
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
apic_write(APIC_ESR, 0);
}
value = apic_read(APIC_LVR);
ver = GET_APIC_VERSION(value);
BUILD_BUG_ON((SPURIOUS_APIC_VECTOR & 0x0f) != 0x0f);
/*
* Double-check whether this APIC is really registered.
*/
if (!apic_id_registered())
BUG();
/*
* Intel recommends to set DFR, LDR and TPR before enabling
* an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
* document number 292116). So here it goes...
*/
init_apic_ldr();
/*
* Set Task Priority to reject any interrupts below FIRST_DYNAMIC_VECTOR.
*/
apic_write_around(APIC_TASKPRI, (FIRST_DYNAMIC_VECTOR & 0xF0) - 0x10);
/*
* After a crash, we no longer service the interrupts and a pending
* interrupt from previous kernel might still have ISR bit set.
*
* Most probably by now CPU has serviced that pending interrupt and
* it might not have done the ack_APIC_irq() because it thought,
* interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
* does not clear the ISR bit and cpu thinks it has already serivced
* the interrupt. Hence a vector might get locked. It was noticed
* for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
*/
for (i = APIC_ISR_NR - 1; i >= 0; i--) {
value = apic_read(APIC_ISR + i*0x10);
for (j = 31; j >= 0; j--) {
if (value & (1<<j))
ack_APIC_irq();
}
}
/*
* Now that we are all set up, enable the APIC
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
/*
* Enable APIC
*/
value |= APIC_SPIV_APIC_ENABLED;
/*
* Some unknown Intel IO/APIC (or APIC) errata is biting us with
* certain networking cards. If high frequency interrupts are
* happening on a particular IOAPIC pin, plus the IOAPIC routing
* entry is masked/unmasked at a high rate as well then sooner or
* later IOAPIC line gets 'stuck', no more interrupts are received
* from the device. If focus CPU is disabled then the hang goes
* away, oh well :-(
*
* [ This bug can be reproduced easily with a level-triggered
* PCI Ne2000 networking cards and PII/PIII processors, dual
* BX chipset. ]
*/
/*
* Actually disabling the focus CPU check just makes the hang less
* frequent as it makes the interrupt distributon model be more
* like LRU than MRU (the short-term load is more even across CPUs).
* See also the comment in end_level_ioapic_irq(). --macro
*/
#if 1
/* Enable focus processor (bit==0) */
value &= ~APIC_SPIV_FOCUS_DISABLED;
#else
/* Disable focus processor (bit==1) */
value |= APIC_SPIV_FOCUS_DISABLED;
#endif
/*
* Set spurious IRQ vector
*/
value |= SPURIOUS_APIC_VECTOR;
/*
* Enable directed EOI
*/
if ( directed_eoi_enabled )
{
value |= APIC_SPIV_DIRECTED_EOI;
apic_printk(APIC_VERBOSE, "Suppress EOI broadcast on CPU#%d\n",
smp_processor_id());
}
apic_write_around(APIC_SPIV, value);
/*
* Set up LVT0, LVT1:
*
* set up through-local-APIC on the BP's LINT0. This is not
* strictly necessery in pure symmetric-IO mode, but sometimes
* we delegate interrupts to the 8259A.
*/
/*
* TODO: set up through-local-APIC from through-I/O-APIC? --macro
*/
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && (pic_mode || !value)) {
value = APIC_DM_EXTINT;
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
smp_processor_id());
} else {
value = APIC_DM_EXTINT | APIC_LVT_MASKED;
apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
smp_processor_id());
}
apic_write_around(APIC_LVT0, value);
/*
* only the BP should see the LINT1 NMI signal, obviously.
*/
if (!smp_processor_id())
value = APIC_DM_NMI;
else
value = APIC_DM_NMI | APIC_LVT_MASKED;
if (!APIC_INTEGRATED(ver)) /* 82489DX */
value |= APIC_LVT_LEVEL_TRIGGER;
apic_write_around(APIC_LVT1, value);
if (APIC_INTEGRATED(ver) && !esr_disable) { /* !82489DX */
maxlvt = get_maxlvt();
if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
apic_write(APIC_ESR, 0);
oldvalue = apic_read(APIC_ESR);
value = ERROR_APIC_VECTOR; // enables sending errors
apic_write_around(APIC_LVTERR, value);
/*
* spec says clear errors after enabling vector.
*/
if (maxlvt > 3)
apic_write(APIC_ESR, 0);
value = apic_read(APIC_ESR);
if (value != oldvalue)
apic_printk(APIC_VERBOSE, "ESR value before enabling "
"vector: %#lx after: %#lx\n",
oldvalue, value);
} else {
if (esr_disable)
/*
* Something untraceble is creating bad interrupts on
* secondary quads ... for the moment, just leave the
* ESR disabled - we can't do anything useful with the
* errors anyway - mbligh
*/
printk("Leaving ESR disabled.\n");
else
printk("No ESR for 82489DX.\n");
}
if (nmi_watchdog == NMI_LOCAL_APIC)
setup_apic_nmi_watchdog();
apic_pm_activate();
}
void __cpuinit setup_local_APIC (void)
{
unsigned int value, maxlvt;
int i, j;
value = apic_read(APIC_LVR);
if ((SPURIOUS_APIC_VECTOR & 0x0f) != 0x0f)
__error_in_apic_c();
/*
* Double-check whether this APIC is really registered.
* This is meaningless in clustered apic mode, so we skip it.
*/
if (!apic_id_registered())
BUG();
/*
* Intel recommends to set DFR, LDR and TPR before enabling
* an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
* document number 292116). So here it goes...
*/
init_apic_ldr();
/*
* Set Task Priority to 'accept all'. We never change this
* later on.
*/
value = apic_read(APIC_TASKPRI);
value &= ~APIC_TPRI_MASK;
apic_write(APIC_TASKPRI, value);
/*
* After a crash, we no longer service the interrupts and a pending
* interrupt from previous kernel might still have ISR bit set.
*
* Most probably by now CPU has serviced that pending interrupt and
* it might not have done the ack_APIC_irq() because it thought,
* interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
* does not clear the ISR bit and cpu thinks it has already serivced
* the interrupt. Hence a vector might get locked. It was noticed
* for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
*/
for (i = APIC_ISR_NR - 1; i >= 0; i--) {
value = apic_read(APIC_ISR + i*0x10);
for (j = 31; j >= 0; j--) {
if (value & (1<<j))
ack_APIC_irq();
}
}
/*
* Now that we are all set up, enable the APIC
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
/*
* Enable APIC
*/
value |= APIC_SPIV_APIC_ENABLED;
/*
* Some unknown Intel IO/APIC (or APIC) errata is biting us with
* certain networking cards. If high frequency interrupts are
* happening on a particular IOAPIC pin, plus the IOAPIC routing
* entry is masked/unmasked at a high rate as well then sooner or
* later IOAPIC line gets 'stuck', no more interrupts are received
* from the device. If focus CPU is disabled then the hang goes
* away, oh well :-(
*
* [ This bug can be reproduced easily with a level-triggered
* PCI Ne2000 networking cards and PII/PIII processors, dual
* BX chipset. ]
*/
/*
* Actually disabling the focus CPU check just makes the hang less
* frequent as it makes the interrupt distributon model be more
* like LRU than MRU (the short-term load is more even across CPUs).
* See also the comment in end_level_ioapic_irq(). --macro
*/
#if 1
/* Enable focus processor (bit==0) */
value &= ~APIC_SPIV_FOCUS_DISABLED;
#else
/* Disable focus processor (bit==1) */
value |= APIC_SPIV_FOCUS_DISABLED;
#endif
/*
* Set spurious IRQ vector
*/
value |= SPURIOUS_APIC_VECTOR;
apic_write(APIC_SPIV, value);
/*
* Set up LVT0, LVT1:
*
* set up through-local-APIC on the BP's LINT0. This is not
* strictly necessary in pure symmetric-IO mode, but sometimes
* we delegate interrupts to the 8259A.
*/
/*
* TODO: set up through-local-APIC from through-I/O-APIC? --macro
*/
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && (pic_mode || !value)) {
value = APIC_DM_EXTINT;
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", smp_processor_id());
} else {
value = APIC_DM_EXTINT | APIC_LVT_MASKED;
apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n", smp_processor_id());
}
apic_write(APIC_LVT0, value);
/*
* only the BP should see the LINT1 NMI signal, obviously.
*/
if (!smp_processor_id())
value = APIC_DM_NMI;
else
value = APIC_DM_NMI | APIC_LVT_MASKED;
apic_write(APIC_LVT1, value);
{
unsigned oldvalue;
maxlvt = get_maxlvt();
oldvalue = apic_read(APIC_ESR);
value = ERROR_APIC_VECTOR; // enables sending errors
apic_write(APIC_LVTERR, value);
/*
* spec says clear errors after enabling vector.
*/
if (maxlvt > 3)
apic_write(APIC_ESR, 0);
value = apic_read(APIC_ESR);
if (value != oldvalue)
apic_printk(APIC_VERBOSE,
"ESR value after enabling vector: %08x, after %08x\n",
oldvalue, value);
}
nmi_watchdog_default();
if (nmi_watchdog == NMI_LOCAL_APIC)
setup_apic_nmi_watchdog();
apic_pm_activate();
}
